TSic 206/203/201/306/303/301 Temperature Sensor IC For a fully calibrated and accurate low power temperature measurement

Transcription

1 TSic 206/203/201/306/303/301 For a fully calibrated and accurate low power temperature measurement Benefits & Characteristics Fully calibrated Custom calibration and assembly available Outstanding accuracy of +/- 0.3 K (TSic 30x) Accuracy range of 80 K can be shifted (default: 10 C to 90 C) Very low power consumption Available with digital, analog and ratiometric output signal Excellent long-term stability Illustration Technical Data Operating temperature range:* -50 C to +150 C (+/- 3 C of measurement limits) Accuracy:* TSic 20x +/- 0.5 K in the range of 10 C to 90 C (other ranges on request) TSic 30x +/- 0.3 K in the range of 10 C to 90 C (other ranges on request) Resolution:* 0.1 K Sampling rate:* 10 Hz Supply voltage: V + = 3 V to 5.5 V, high precision operation in range V + = 4.5 V to 5.5 V Supply current: typ. 30 μa at 25 C and V + = 3.3 V for minimal self-heating Packaging:* SOP-8 or TO92 (other packaging on request) * Customer specific alternatives available Packaging pin assignment: Pin 1 Pin 2 Pin 3 Pin 4 SOP-8 (5, 6, 7 and 8 not used) V+, Supply voltage (3 V to 5.5V) Signal Not used GND TO92 GND Signal V+, Supply voltage (3 V to 5.5 V) 1/4

2 TSic 206/203/201/306/303/301 For a fully calibrated and accurate low power Absolute max. rating Min Max Supply voltage (V + ) -0.3 V 6 V Voltages to analog I/O Pins (V INA, V OUTA ) -0.3 V V DDA +0.3 V Storage temperature range (T STOR ) -20 C 80 C Operating conditions Min Typ Max Supply voltage to GND (V + ) 2.97 V 5 V 5.5 V Supply current (I V+ V + = 3.3 V, RT 25 μa 30 μa 60 μa Operating temperature range (T amb ) -50 C +150 C Output load capacitance (C L ) External capacitance between V + and GND 1) (C V+ ) Output load resistance between signal and GND (or V + ) 100 nf (recommended) 47 kohm 15 nf Temperature accuracies 2) TSic 30x TSic 20x T1: +10 C to 90 C +/- 0.3 K +/- 0.3 K T2: -20 C to +110 C +/- 0.6 K +/- 1 K T3: -50 C to +150 C +/- 1.2 K +/- 2 K 1) Recommended as close to TSic V + and GND-Pins as possible 2) The sensor is calibrated at 5 V. The provided accuracy is applicable for a supply voltage between 4.5 V and 5.5 V. The accuracy is smaller with a supply voltage between 2.97 V and 4.5 V. For applications where the best accuracy at 3 V is requested, ask for a custom specific 3 V calibrated device. Other TSic TM products with custom specific calibrations are available upon request e.g. other temperature range for high accuracy. Accuracy at delivery; the assembly method can influence the accuracy! Order Information - SOP-8 Output signal Analog Analog ratiometric Digital, ZACWire protocol 201/203/206 TSic 201 SOP-8 TSic 203 SOP-8 TSic 206 SOP-8 Order code /303/306 TSic 301 SOP-8 TSic 303 SOP-8 TSic 306 SOP-8 Order code /4

3 TSic 206/203/201/306/303/301 For a fully calibrated and accurate low power Order Information - TO92 Output signal Analog Analog ratiometric Digital, ZACWire protocol 201/203/206 TSic 201 TO92 TSic 203 TO92 TSic 206 TO92 Order code /303/306 TSic 301 TO92 TSic 303 TO92 TSic 306 TO92 Order code Additional Electronics Labkit Document name: DTTSicLABkit_E 3/4

4 Order Information Secondary reference TSic Accuracy 2 = +/- 0.5 C at 80 C range 3 = +/- 0.3 C at 80 C range 4 = not defined 5 = +/- 0.1 C at 40 C range (limited measuring range from -10 C to + 60 C) 6 = not defined 7 = +/ C at 20 C range (limited measuring range from -10 C to + 60 C) Bit size 0 = 11 bit 1 = 14 bit Output signal 1 = analog 0 V to 1 V 3 = ratiometric 10 % to 90 % V + 6 = digital ZACWire protocol Housing SOP-8 TO92 KGD ( known-good-die in waffle pack, 100 pcs/pkg) Special E.g. 250 Hz for a high sampling rate or -30/70 for temperature and tolerance range 1) TSic TO92-30/70 TSic TO92-30/70 1) Standard: no value DTTSic20x_30x_E2.1 Innovative Sensor Technology IST AG, Stegrütistrasse 14, CH-9642 Ebnat-Kappel, Switzerland, Phone: +41 (0) Fax: +41 (0) info@ist-ag.com Web: 4/4 All mechanical dimensions are valid at 25 C ambient temperature, if not differently indicated All data except the mechanical dimensions only have information purposes and are not to be understood as assured characteristics Technical changes without previous announcement as well as mistakes reserved The information on this data sheet was examined carefully and will be accepted as correct; No liability in case of mistakes Load with extreme values during a longer period can affect the reliability The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner Typing errors and mistakes reserved Product specifications are subject to change without notice All rights reserved

5 TSic 506F/503F/501F For a fully calibrated and very accurate low power Benefits & Characteristics Fully calibrated Custom calibration and assembly available Outstanding accuracy of +/- 0.1 K Available with digital, analog and ratiometric output signal Very low power consumption Accuracy range of 40 K can be shifted (default: 5 C to 45 C) Excellent long-term stability Illustration Technical Data Operating temperature range:* Accuracy:* Resolution:* Sampling rate:* Supply voltage: Supply current: Packaging:* -10 C to +60 C (+/- 3 C of measurement limits) +/- 0.1 K in the range of 5 C to 45 C (other ranges upon request) K 10 Hz V + = 3 V to 5.5 V, high precision operation in range V + = 4.5 V to 5.5 V typ. 30 μa at 25 C and V + = 3.3 V for minimal self-heating SOP-8 or TO92 * Customer specific alternatives available Packaging pin assignment: Pin 1 Pin 2 Pin 3 Pin 4 SOP-8 V+, Supply voltage (3 V to 5.5V) Signal Not used GND TO92 GND Signal V+, Supply voltage (3 V to 5.5 V) 1/4

6 TSic 506F/503F/501F For a fully calibrated and very accurate low power Absolute max. rating: Min Max Supply voltage (V + ): -0.3 V 6 V Voltages to analog I/O Pins (V INA, V OUTA ): -0.3 V V DDA +0.3 V Storage temperature range (T STOR ): -20 C 80 C Operating conditions: Min Typ Max Supply voltage to GND (V + ): 2.97 V 5 V 5.5 V Supply current (I V+ V + = 3.3 V, RT: 25 μa 30 μa 60 μa Operating temperature range (T amb ): -10 C +60 C Output load capacitance (C L ): External capacitance between V + and GND 1) (C V+ ): Output load Resistance between signal and GND (or V + ): 100 nf (recommended) 47 kohm 15 nf Temperature accuracies: 2) T1: 5 C to 45 C +/- 0.1 K T2: -10 C to 60 C +/- 0.2 K 1) Recommended as close to TSic V + and GND-Pins as possible 2) The sensor is calibrated at 5 V. The provided accuracy is applicable for a supply voltage between 4.5 V and 5.5 V. The accuracy is smaller with a supply voltage between 2.97 V and 4.5 V. For applications where the best accuracy at 3 V is requested, ask for a custom specific 3 V calibrated device. Other TSic TM products with custom specific calibrations are available upon request e.g. other temperature range for high accuracy. Accuracy at delivery; the assembly method can influence the accuracy! Order Information - SOP-8 Output signal Analog Analog ratiometric Digital, ZACWire protocol 501/503/506 TSic 501F SOP-8 TSic 503F SOP-8 TSic 506F SOP-8 Order code /4

7 TSic 506F/503F/501F For a fully calibrated and very accurate low power Order Information - TO92 Output signal Analog Analog ratiometric Digital, ZACWire protocol 501/503/506 TSic 501F TO92 TSic 503 TO92 5V TSic 506F TO92 Order code Additional Electronics Labkit Document name: DTTSicLABkit_E 3/4

8 Order Information Secondary reference TSic Accuracy 2 = +/- 0.5 C at 80 C range 3 = +/- 0.3 C at 80 C range 4 = not defined 5 = +/- 0.1 C at 40 C range (limited measuring range from -10 C to + 60 C) 6 = not defined 7 = +/ C at 20 C range (limited measuring range from -10 C to + 60 C) Bit size 0 = 11 bit 1 = 14 bit Output signal 1 = analog 0 V to 1 V 3 = ratiometric 10 % to 90 % V + 6 = digital ZACWire protocol Housing SOP-8 TO92 KGD ( known-good-die in waffle pack, 100 pcs/pkg) Special E.g. 250 Hz for a high sampling rate or -30/70 for temperature and tolerance range 1) TSic TO92-30/70 TSic TO92-30/70 1) Standard: no value DTTSic50x_E2.1 Innovative Sensor Technology IST AG, Stegrütistrasse 14, CH-9642 Ebnat-Kappel, Switzerland, Phone: +41 (0) Fax: +41 (0) info@ist-ag.com Web: 4/4 All mechanical dimensions are valid at 25 C ambient temperature, if not differently indicated All data except the mechanical dimensions only have information purposes and are not to be understood as assured characteristics Technical changes without previous announcement as well as mistakes reserved The information on this data sheet was examined carefully and will be accepted as correct; No liability in case of mistakes Load with extreme values during a longer period can affect the reliability The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner Typing errors and mistakes reserved Product specifications are subject to change without notice All rights reserved

9 TSic 716 For a fully calibrated and extremely accurate low power Benefits & Characteristics Fully calibrated (custom calibration and assembly available) Accuracy range of 20 K can be shifted (default: 25 C to 45 C) Outstanding accuracy of +/ K Easy to integrate (digital output signal) Very low power consumption Capable of communicating over a distance of > 10 m Excellent long-term stability Illustration Technical Data Operating temperature range:* Accuracy:* Resolution:* Sampling rate:* Supply voltage:* Supply current: Digital signal output: Packaging:* -10 C to +60 C (+/- 3 C of measurement limits) +/ K in the range of 25 C to 45 C (other ranges upon request) 4 mk 10 Hz 4.5 V to 5.5 V typ. 45 μa at 25 C and 5 V for minimal self-heating (14 bit) compatible with state-of-the-art microcontrollers using only a single signal wire TO92 * Customer specific alternatives available Packaging pin assignment: Pin 1 Pin 2 Pin 3 Pin 4 TO92 GND Signal V+, Supply voltage (3 V to 5.5 V) 1/3

10 TSic 716 For a fully calibrated and extremely accurate low power Absolute max. rating: Min Max Supply voltage (V + ) -0.3 V 6 V Voltages to analog I/O Pins (V INA, V OUTA ) -0.3 V V DDA +0.3 V Storage temperature range (T STOR ) -20 C 80 C Operating condition Min Typ Max Supply voltage to GND (V + ) 2.97 V 5 V 5.5 V Supply current (I V+ V + = 3.3 V, RT 30 μa 45 μa 80 μa Operating temperature range (T amb ) -10 C +60 C Output load capacitance (C L ) External capacitance between V + and GND 1) (C V+ ) Output load resistance between signal and GND (or V + ) 100 nf (recommended) 47 kohm 15 nf Temperature accuracies 2) T1: 25 C to 45 C +/ K T2: -10 C to 60 C +/- 0.2 K 1) Recommended as close to TSic V + and GND-Pins as possible 2) The sensor is calibrated at 5 V. The provided accuracy is applicable for a supply voltage between 4.5 V and 5.5 V. The accuracy is smaller with a supply voltage between 2.97 V and 4.5 V. For applications where the best accuracy at 3 V is requested, ask for a custom specific 3 V calibrated device. Other TSic TM products with custom specific calibrations are available on request e.g. other temperature range for high accuracy. Accuracy at delivery; the assembly method can influence the accuracy! Order Information - TO92 Output signal Digital, ZACWire protocol 716 TSic 716 TO92 Order code Additional Electronics Labkit Document name: DTTSicLABkit_E 2/3

11 Order Information Secondary reference TSic Accuracy 2 = +/- 0.5 C at 80 C range 3 = +/- 0.3 C at 80 C range 4 = not defined 5 = +/- 0.1 C at 40 C range (limited measuring range from -10 C to + 60 C) 6 = not defined 7 = +/ C at 20 C range (limited measuring range from -10 C to + 60 C) Bit size 0 = 11 bit 1 = 14 bit Output signal 1 = analog 0 V to 1 V 3 = ratiometric 10 % to 90 % V + 6 = digital ZACWire protocol Housing SOP-8 TO92 KGD ( known-good-die in waffle pack, 100 pcs/pkg) Special E.g. 250 Hz for a high sampling rate or -30/70 for temperature and tolerance range 1) TSic TO92-30/70 TSic TO92-30/70 1) Standard: no value DTTSic716_E2.1 Innovative Sensor Technology IST AG, Stegrütistrasse 14, CH-9642 Ebnat-Kappel, Switzerland, Phone: +41 (0) Fax: +41 (0) info@ist-ag.com Web: 3/3 All mechanical dimensions are valid at 25 C ambient temperature, if not differently indicated All data except the mechanical dimensions only have information purposes and are not to be understood as assured characteristics Technical changes without previous announcement as well as mistakes reserved The information on this data sheet was examined carefully and will be accepted as correct; No liability in case of mistakes Load with extreme values during a longer period can affect the reliability The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner Typing errors and mistakes reserved Product specifications are subject to change without notice All rights reserved

12 TSic LABkit for USB/Windows An effective Plug&Play development tool Benefits & Characteristics Allows simultaneous display (up to 4 temperature signals in real time) TM Easy testing of TSic without programming microcontrollers User-friendly software for temperature data display and customer-specific sensor configurations Display of min., max. and average temperatures for each attached sensor Measurement interval selection and data recording Data recording in a text file (can be exported to other applications e.g. Excel) Illustration Technical Data Compatible TSic TM sensors: PC system requirements: PC-connection: TSic206, TSic306, TSic506F, TSic716 Microsoft Windows 98, Windows 8.1, 2000 or XP; 200 MHz CPU; 64 MB RAM; 10 MB disk space; CDROM or DVD drive; USB interface USB with 1 m (3 ft.) cable Connector: Molex LABkit includes: USB adapter for up to four temperature sensors (USB cable included), 4 TSic 306 TO92 1) sensor ICs with cable, recorder data acquisition, display and recording software for PC/Windows 2) 1) Other sensor combinations on request 2) Installation in German only; running software both in German and English V+ (must be connected in the white area) SIG GND Packaging pin assignment: Pin 1 Pin 2 Pin 3 TO92 GND (VSS) Signal V+ (VDD), supply voltage (3 V to 5.5 V) 1/2

13 TSic LABkit for USB/Windows An effective Plug&Play development tool Order Information Order code TSic LABkit für USB/Windows DTTSic LABKit_E2.1 Innovative Sensor Technology IST AG, Stegrütistrasse 14, CH-9642 Ebnat-Kappel, Switzerland, Phone: +41 (0) Fax: +41 (0) Web: 2/2 All mechanical dimensions are valid at 25 C ambient temperature, if not differently indicated All data except the mechanical dimensions only have information purposes and are not to be understood as assured characteristics Technical changes without previous announcement as well as mistakes reserved The information on this data sheet was examined carefully and will be accepted as correct; No liability in case of mistakes Load with extreme values during a longer period can affect the reliability The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner Typing errors and mistakes reserved Product specifications are subject to change without notice All rights reserved