LIMO40-F400-DL980-LM High Power Diode Laser System for Medical Applications

Transcription

1 LIMO40-F400-DL980-LM High Power Diode Laser System for Medical Applications Your product benefits: - Plug and play fiber connector - Compact housing - High E/O efficiency - Hermetically sealed housing - 2 temperature sensors (NTC/PT100) - Exchangeable protection window Medical Solutions product similar to image Laser Module Unit Value Unit Value Optical Data Fiber Connection Data CW - nominal output power W 40 Fiber core diameter µm 400 Center wavelength nm 980 Numerical aperture 0,22 Wavelength tolerance (±) nm 10 Fiber - optic connector SMA905 Spectral width (FWHM) nm 5 Cladding mode (max) % Not specified Wavelength temperature drift nm/k 0,4 Thermal Operation Conditions Package Nominal diode heat sink temperature C 25 Dimensions mm³ 111x25x37 Diode heat sink operation temperature C Weight basic package kg 0,35 Minimum heat sink capacity W 80 Storage temperature C Electrical Data Typical operation current A 55 Max. operation current A 66 Typical threshold current A 8 Typical operation voltage V 2 Typical slope W/A 0,9 Typical O/E efficiency % 44 Additional Features Unit Value Unit Value Pilot Beam 2 x Monitor diode Output power (min) mw 0,7 Operation voltage V 5 Wavelength nm 650 Output signal (min) V 0 Voltage V 3 5 Output signal (max) V 2,5 Current (max) ma x Fiber detection sensor (PNP) Other Features Voltage V 12 Temperature sensors NTC & PT100 Current (max) ma 100 Exchangeable protection window Yes LIMO Lissotschenko Mikrooptik GmbH Bookenburgweg Dortmund, Germany Phone: Fax: kontakt@limo.de Management: Dr. Vitalij Lissotschenko and Dr. Lutz Aschke and Dr. Paul Harten Trade Register Dortmund HRB 11639

2 LIMO40-F400-DL980-LM High Power Diode Laser System for Medical Applications LIMO40-F400-DL980-LM with thermoelectric cooling RoHS compliant 2002/95/EG All data provided are typically measured with a diode heat sink temperature of 25 C. All measurements are made with a LIMO reference fiber 400 µm, length 1.5 m, and non AR coated. Copyright 2012 LIMO GmbH. All rights reserved. All LIMO products are patent pending. Subject to change without notice. Version August 01, 2012 LIMO Lissotschenko Mikrooptik GmbH Bookenburgweg Dortmund, Germany Phone: Fax: kontakt@limo.de Management: Dr. Vitalij Lissotschenko and Dr. Lutz Aschke and Dr. Paul Harten Trade Register Dortmund HRB 11639

3 Laser & Peltier Driver Type: ds11-la75v05-pa07v48-t12734-v1-579 Laser max.: 75A, 5V TEC max.: 7A, 48V trise-tfall < 25us (optional < 10us) Supply Voltage: 90~230VAC External, Internal, Analog and Digital Modulation, Bias Current option, Pilot Laser Supply, External Fan Support, optional additional TECs Laser Connector Sub-5W5, female Type as viewed from backside PIN.No Abbr. Function A3;A4 LDA+ Laser Diode Anode (+) A1;A2 LDC- Laser Diode Cathode (-) Peltier Connector Sub-D 15, female Type as viewed from backside LPEL+ PDC- PL+ LED LPEL V GND TEMP1 SCR PIN.No Abbr. Function 4 LED LASER-RUN LED 5 PL+ PILOTLASER+ Pin 6 PDC- Photo-Diode Kathode (connect Anode to GND) 7;8 LPEL+ L Peltier element (+) 11 TEMP1 Temperature Sensor Input vs. GND 12 GND Common Ground V 1..24V Supply, max. 800mA (vs GND) supports fan etc. 14;15 LPEL- L Peltier element (-) 1;2;9;10 n.c. SCR Common Screen c_lp_t12734_v1_579 OsTech (c) /2

4 Laser & Peltier Driver RS232 Connector AMOD/DMOD Connector Interlock Connector GND TXD RXD Sub-D 9, female BNC Coaxial Connector Jack Connector 3.5mm Standard RS232-Connector connected to PC (No Null-Modem Cable!) Input-Impdanz 10kOhm Digital Modulation with TTL-Pegel Analog Modulation 0-4[V] => 0-Imax[A] Interlock - Laser runs only if closed (ca. 5mA over 2V -> R Interlock <=400R) rear of the device length = 275mm (10.8 ) c_lp_t12734_v1_579 OsTech (c) /2

5 active cooling block Type: HSA F012-B02-M07-D06-S cooling block corresponding to OsTech laser-tec-driver pinout for Lumics LuOcean Mini direct mounting of diode lasers to cooling block with integrated TEC modules Cooling block could handle typical power loss of laser-diode in conjunction with laser temperature: ambient temperature 25 C ambient temperature 35 C max. el. fan data: 2x 24V / 3,6W max. noise value: 44dB(A) max. TEC values: 8A / 14V (1,25 Ohm/25 C) mounting area: 85mm x 65mm 15 C 75W 20 C 85W 25 C 95W 30 C 105W 15 C 44W 20 C 53W 25 C 62W 30 C 71W optional: Mounting plate for heat sink 15p male connector, if using 1:1 cable and Ostech driver unit Lumics type (e.g. 282) Sub-D 15, male Type V+ FIN TSENI LLED PL+ PD PEL V TSENSUP GND 1..24V PEL- SCR abbr. function 1 12V+ Fibre Sensor Supply 12V 2 FIN Fibre Sensor Input 3 TSENI Temp. Sensor Input 4 LLED connected Laser On LED 5 PL+ optional Pilot Laser (+) (PL- at Pin GND) c_hsa_ VER:01 OsTech (c) /2

6 active cooling block Type: HSA F012-B02-M07-D06-S PD optional Photo Diode 0..4V 7;8 PEL+ connected Peltier element (+) 10 +5V optional 5V Supply 11 TSENUP optional Temp. Sensor Supply; 12 GND connected Common Ground N.C. To Screen V connected 1..24V Supply, max. 300mA (-24V at GND) supports fan etc. 14;15 PEL- connected Peltier element (-) SCR Common Screen Laser Connector SubD-2W2, male Type PIN.No Abbr. Function A1 LDA+ Laser Diode Anode (+) A2 LDC- Laser Diode Cathode (-) c_hsa_ VER:01 OsTech (c) /2