Compact EDFA. HIGH Power Fiber Technology.

Transcription

1 HIGH Power Compact EDFA Features: - Output Power up to +20 dbm - Industry Standard Form Factor (70x90x12mm) - Gain-Flattened Version for Wideband Amplification - Uncooled Pump Option - Telcordia Qualified - ROHS Compliant Applications: - Long Haul and Metro Networks - Transmitter and Receiver Amplification - Single Channel, Narrowband and Wideband DWDM The Manlight compact EDFA is field proven and offers excellent optical performance and reliability. The compact EDFA gain block is intended for DWDM applications in the C- & L-band wavelength range. It can be optimized to perform as a booster, line or pre-amplifier in DWDM systems and subsystems for metro and long haul applications. The gain block contains input and output monitor diodes and isolators. The EDFA can be configured to use an uncooled pump laser that enables low power consumption which allows system designers to achieve compact solutions, lower costs and flexibility in system design.

2 HIGH Power Optical Characteristics Parameter Booster Single-Channel Pre-Amp Single-Channel Gain - Flattened Wavelength Range nm Maximum Output Power dbm Input Power Range -10 to to to -5 dbm Nominal Gain db Gain Flatness Nominal Gain N/A N/A 1.0 db Gain Flatness Nominal Gain N/A N/A 1.5 db Noise Figure Nominal Gain db Noise Figure Nominal Gain db Polarization Mode Dispersion ps Polarization Dependent Gain db Unit Electrical & Environmental Characteristics Power Consumption (typical / max EOL) 4.0 / / / 8.0 W Power Consumption (Uncooled version) 1.0 / / / 1.5 W Operating Case Temperature 0 to +70 C Storage Temperature -40 to +85 C Operating Humidity (non-condensing) 5-95 % RH Electrical Pin-Out The electrical connector is a 20-pin male connector. Pin # Description Pin # Description 1 GND 11 Thermoelectric Cooler, Positive 2 Input Monitor Cathode 12 Thermoelectric Cooler, Positive 3 Input Monitor Anode 13 Thermoelectric Cooler, Positive 4 Output Monitor Cathode 14 Thermoelectric Cooler, Negative 5 Output Monitor Anode 15 Thermoelectric Cooler, Negative 6 Thermistor 16 Thermoelectric Cooler, Negative 7 Laser Diode Anode 17 GND 8 Laser Diode Anode 18 Thermistor 9 Backface Monitor Cathode 19 Laser Diode Cathode 10 Backface Monitor Anode 20 Laser Diode Cathode Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice.

3 HIGH Power Compact EDFA with Control Electronics Features: - Fast Transient Control - Output Power up to +23 dbm - ROHS Compliant - Uncooled Pump Option - Telcordia Qualified - Gain-Flattened Version for Full-band Amplification - Industry Standard Form Factor (70x90x15mm) - State-of-the-Art Integrated Control Electronics Applications: - Long Haul and Metro Networks - Transmitter and Receiver Amplification - Single Channel, Narrowband and Wideband DWDM The Manlight Compact EDFA gain module with integrated control electronics is suitable for DWDM systems where fast transient control and gain flattening is required. It can be optimized to perform as a booster, line and pre-amplifier in systems and subsystems for metro and long haul applications. It operates in constant gain, constant power mode or in constant current mode. The gain block contains input and output monitor diodes and isolators. The EDFA can be configured to use an uncooled pump laser that enables low power consumption which allows system designers to achieve compact solutions, lower costs and flexibility in system design.

4 HIGH Power Optical Characteristics Parameter Booster Single-Channel Pre-Amp Single-Channel Gain - Flattened Wavelength Range nm Maximum Output Power dbm Input Power Range -10 to to to -3 dbm Nominal Gain db Gain Flatness Nominal Gain N/A N/A 0.8 db Gain Flatness Nominal Gain N/A N/A 1.5 db Noise Figure Nominal Gain db Noise Figure Nominal Gain db Polarization Mode Dispersion ps Polarization Dependent Gain db Electrical & Environmental Characteristics Transient Settling Time (typ / max) 50 / 200 μs Transient Overshoot/Undershoot (typ/max) 0.3 / 0.8 db Power Consumption (typical / max EOL) 6.0 / / / 12.0 W Power Consumption (Uncooled version) 2.0 / / / 3.5 W Power Supply Voltage +3.3 or +5.0 VDC Operating Case Temperature 0 to +70 C Storage Temperature -40 to +85 C Operating Humidity (non-condensing) 5-95 % RH Unit Electrical Pin-Out The electrical connector is a 30-pin female connector. Pin# Description Pin# Description Pin# Description V / +5.0 V 11 NC 21 Input Power Mon GND V / +5.0 V 12 Reset 22 Output Power Mon GND V / +5.0 V 13 Amplifier Disable 23 Input Power Monitor V / +5.0 V 14 Output Power Mute 24 Output Power Monitor 5 GND 15 Case Temp Alarm 25 GND 6 GND 16 NC 26 GND 7 RS-232 IN (TTL) 17 Pump Temp. Alarm V / +5.0 V 8 RS-232 OUT (TTL) 18 Pump Bias Alarm V / +5.0 V 9 GND 19 Loss of Input Alarm V / +5.0 V 10 GND 20 Loss of Output Alarm V / +5.0 V Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice.

5 HIGH Power High Power Amplifier Features: - Output Power up to +35 dbm - 1 to 16 Output Ports - Cost Effective Amplification - Low Power Consumption - RS-232 Command Interface - ROHS Compliant Applications: - CATV - FTTx, PON - Free space, Broadband Access - R&D, Test & Measurement The Manlight High Power Amplifier for CATV and FTTx applications offers a cost effective solution in bringing the bandwidth closer to the end users. With a unique design based on Manlights in-house pump combiner and optical know-how, the high power amplifiers are optimized to offer high power and low noise figure with proven reliability and quality. The output power can be distributed between 1 to 16 output ports. The use of efficient and reliable uncooled pump diodes allows the Manlight amplifiers to reach high output powers with low overall power consumption. The control electronics featuring alarms, automatic shutdown, and RS-232 communication interface is driven by a 5 / 24 VDC power supply.

6 HIGH Power Optical Characteristics Parameter General 16x20 dbm Unit Wavelength Range nm Output Power Up to per port dbm Number of Output Ports Input Power Range -10 to to +10 dbm Noise 1550nm, +0dBm Input Power db Port to Port Variation 0.6 for 8 ports 1.0 db Polarization Mode Dispersion ps Polarization Dependent Gain db Electrical & Environmental Characteristics Power Consumption (typical) - 32 W Power Supply Voltage 5 or 24 VDC Operating Case Temperature 0 to +65 C Storage Temperature -40 to +85 C Operating Humidity (non-condensing) % RH Connector type D-sub 25 Mechanical Dimensions 150 x 125 x32 or 240 x170 x 38 mm Mechanical Drawing 80,00 A 150,00 20,80 143,50 B 11,00 8,50 4,25 47,00 A Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice. 22,00 32,00 B 118,50 A 3,50 (x4) A 125,00

7 HIGH Power High Power Benchtop 1.5µm Amplifier Features: - Output Power up to +43 dbm - Low Noise Figure - RS-232 and GPIB interfaces - Labview drivers - Wide display and easy access menus - High reliability Applications: - Test and Measurements - Booster Amplifier for Transmitters - Sensor & LIDAR The Manlight high power bench top amplifiers are optimized to offer high performance and low noise figure with proven reliability and quality. These amplifiers are intended to be used in various domains like high speed optical transmissions, booster amplifier for transmitters, sensors as well as test and measurement setups. Featuring on board control electronics capabilities, these PM EDFAs can be operated in variety of control modes including Automatic Current Control (ACC), Automatic Power Control (APC) or Automatic Gain Control (AGC). Delivered with standard GPIB and RS-232 interfaces, these units offer a user-friendly interface ideal for PC-remote-controlled system experiments. Available in a x 257 x 376 mm package.

8 HIGH Power Optical Characteristics Parameter B27 B30 B33 B37 B43 Unit Wavelength Range nm Output Power dbm Input Power Range -10 to to to to to +10 dbm Noise 1550nm, +0dBm db Polarization Mode Dispersion ps Optical Return Loss db Polarization Dependent Gain db Electrical & Environmental Characteristics Interface type RS232 and GPIB Power Supply Voltage , 50-60Hz V Operating Case Temperature 10 to +45 C Control modes Alarms Optical Connectors APC, ACC, AGC Output power loss Pump bias alarm Pump temperature alarm SC or FC Mechanical Dimensions 155,5 x 257 x 376 mm Bench top Functionality Easy access menus with display Optical characteristics display: Output & Input Power Programmable operating point (Output power, Pump current) Electrical characteristics display: Laser currents, laser temperatures Alarms display Save and recall functions for easy restart Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice.

9 HIGH Power Features: - Output Power up to +40 dbm - High Polarization Extinction Ratio - RS-232 and GPIB interfaces - Labview drivers - Wide display and easy access menus - High reliability High Power Polarization1.5µm Maintaining Benchtop Amplifier Applications: - Test and Measurements - Booster Amplifier for PM Transmitters - Sensor & LIDAR The Manlight high power polarization maintaining bench top amplifiers are optimized to offer high performance and low noise figure with proven reliability and quality. These amplifiers are intended to be used in various domains like high speed optical transmissions (polarization multiplexing), PM transmitters, sensors as well as test and measurement setups. Featuring on board control electronics capabilities, these PM EDFAs can be operated in variety of control modes including Automatic Current Control (ACC), Automatic Power Control (APC) or Automatic Gain Control (AGC). Delivered with standard GPIB and RS-232 interfaces, these units offer a user-friendly interface ideal for PC-remote-controlled system experiments. Available in a x 257 x 376 mm package.

10 HIGH Power Optical Characteristics Parameter PM27 PM30 PM33 PM37 PM40 Unit Wavelength Range nm Output Power dbm Input Power Range -10 to to to to to +10 dbm Polarization Extinction Ratio db Noise 1550nm, +0dBm db Polarization Axis Slow axis Slow axis Slow axis Slow axis Slow axis Optical Return Loss db Polarization Dependent Gain db Electrical & Environmental Characteristics Interface type Mechanical Drawing and Electrical Pin-Out RS232 and GPIB Power Supply Voltage , 50-60Hz V Operating Case Temperature 10 to +45 C Control modes Alarms Optical Connectors APC, ACC, AGC Output power loss Pump bias alarm Pump temperature alarm SC or FC Mechanical Dimensions 155,5 x 257 x 376 mm Bench top Functionality Easy access menus with display Optical characteristics display: Output & Input Power Programmable operating point (Output power, Pump current) Electrical characteristics display: Laser currents, laser temperatures Alarms display Save and recall functions for easy restart Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice.

11 HIGH Power Compact Multi-Port Gain Block Features: - Up to 8 Output Ports - Cost Effective Amplification - Low Power Consumption - Compact Form Factor (70x90x15mm) - Uncooled Pump - ROHS Compliant Applications: - CATV - FTTx, PON - Free space, Broadband Access The Manlight Compact Multi-Port Gain Block for CATV and FTTx applications offers a cost effective solution in bringing the bandwidth closer to the end users. With a unique design based on Manlights in-house pump combiner and optical know-how, the high power amplifiers are optimized to offer high power and low noise figure with proven reliability and quality. The output power can be distributed between 1 to 8 output ports. The use of efficient and reliable uncooled pump diodes allows the Manlight amplifiers to reach high output powers with low overall power consumption.

12 60,00 HIGH Power Optical Characteristics Parameter 4x18 dbm 4x20 dbm 8x18 dbm 8x20 dbm Unit Wavelength Range nm Output Power per Port dbm Number of Output Ports Input Power Range 0 to to to to +15 dbm Noise 1550nm, +6dBm Input Power db Port to Port Variation db Polarization Mode Dispersion ps Polarization Dependent Gain db Electrical & Environmental Characteristics Power Consumption (typical) W Power Consumption (maximum, EOL) W Operating Case Temperature 0 to +65 C Storage Temperature -20 to +75 C Operating Humidity (non-condensing) % RH Mechanical Characteristics Mechanical Dimensions 70x90x15 70x108x15 70x90x15 70x108 x15 70x90x15 70x108x15 70x108x15 mm Mechanical Drawing 40,00A 70,00 A 15,00 21,00 21,50 63,00 A 4,50 Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice. 4,00 10,50 101,00 B 108,00 Samtec SQ Tail Socket SQT L-D B

13 HIGH Power Variable Gain Amplifier Features: - Two Independent Variable Gain Stages - State-of-the-Art Control Electronics with Fast Transient Suppression Control - Mid-Stage Access - Integrated Optical Supervisory Channel Add/Drop - Ultra Compact Package Size (100 x 130 x 15 mm) - Provides Flat Gain Across a Wide Gain Range of 15dB, ensuring Compatibility with Systems with Differing Link Losses - Telcordia Qualified - ROHS Compliant Applications: - Test and Measurements - Booster Amplifier for PM Transmitters - Sensor & LIDAR The Manlight Variable Gain Amplifier is the next-generation controlled amplifier with two independent variable gain stages that enables significant cost and space saving. With stateof-the-art transient suppression control and best in class optical performance the Manlight variable gain amplifier is well suited for agile networks with reconfigurable optical add/drop nodes (ROADM) and varying link budgets. Designed for use in the long haul and Metro DWDM optical networking systems, where the ability to respond to changing conditions is a key requirement.

14 HIGH Power Optical Characteristics Parameter VGA Mid-Stage Access VGA 2 Separate Stages Comments Wavelength Range nm Maximum Output Power dbm Input Power Range -32 to to +12 Dynamic Range: 40 db dbm Gain Range Dynamic Range: 15 db db Mid-Stage Loss Range 0-15 N/A db Gain Flatness Nominal Gain Peak to Peak db Gain Flatness Nominal Gain Peak to Peak db Noise Figure Max Gain & Power db Noise Figure Max Gain & Power db Polarization Mode Dispersion ps Polarization Dependent Gain db Optical Supervisory Channel Electrical & Environmental Characteristics Optional Transient Settling Time (15dB Add/Drop) (typ/max) 150 / 400 μs Transient Overshoot/Undershoot (15dB Add/Drop) (typ/max) 0.5 / 1.0 db Power Consumption (typical / max, EOL worst case) 10 / 20 W Power Supply Voltage +5.0 VDC Operating Case Temperature 0 to +70 C Storage Temperature -40 to +85 C Operating Humidity (non-condensing) 5-95 % RH Unit nm Mechanical Drawing Information given in this data sheet is belived to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Manlight. These products are sold only according to Manlight s general conditions of sale, unless otherwise confirmed in writing. Product specifications subject to change without notice.

15 Information countains in this document is subject to change without notice Features: - Linear Polarization - For SLM laser amplification - Excellent beam quality (M²<1.1) - Up to 15W CW of output power in 1.0µm - Up to 10W CW of output power in 1.5µm - All optical isolated - Highly reliable laser diode pumps - Convenient front panel control - Maintenance free operation - Compact & rugged design - Including heat sink & fan - Cables including - Safety interlock - Air cooled - USB Applications: - Atom cooling and atom trapping - Spectroscopy - Frequency doubling - Micromachining - Measurement - Telecom - Component testing - Coherent detection - Medical - R&D HED Product Line 1.0µm and 1.5µm CW SLM PM Fiber Amplifiers ML-YFA-CW-SLM-P-TKS Series ML-EYFA-CW-SLM-P-TKS Series The ML-YFA/EYFA-CW-SLM-P-TKS, Turn Key System is a compact CW Fibre Amplifier delivering up to 15W of output power at 1.0µm and 10W at 1.5µm, through a near diffraction limited linearly polarized beam (M²<1.3). The ML-YFA/EYFA-CW-SLM-P-TKS is optimised for the amplification of Single Longitudinal Mode (SLM) laser sources of down to 10kHz instantaneous Full Width at Half Maximum (FWHM). The design and configuration of this amplifier render it unique and reliable. The power is delivered trough a polarized beam and with excellent power stability. Our patented Injection Technology allows the use of highly reliable broad area laser diode pumps, for a cost-effective and maintenance-free operation. The allfibre design guarantees the robustness of the amplifier, without any optical parts to align or to stabilise. The simple integration of the Bench Top system requires no after-installation service. Manlight, based in Brittany, has chosen words in local Celt language, the Breton, to personalize its product portfolio. Each of the eight fiber laser and amplifier product lines starts with a letter of Manlight. HED in Breton stands for Wavelength. Thus perfectly adapted to our 1.5µm and 1.0µm high power CW PM SLM fiber amplifiers Manlight S.A.S. - 4, rue Louis de Broglie Lannion, France - sales@manlight-alcen.com

16 HED Product Line ML**-YFA-CW-SLM-P-TKS Series Technical Specification: Ordering Information: MLxx-YFA-CW-SLM-P-TKS xx = Average output power in Watts Parameter Value Unit Operation mode CW - Nominal Seed Laser Wavelength 1064 typ. nm Seed Laser Wavelegth Range nm Seed Laser Instantaneous Linewidth > 10 khz Nominal input power 25 mw Input power range mw Nominal output power (@ 25mW input) W Output power tunability % Long term stability (RMS, over 1h@25 C) <+/- 2 % Polarization Linear - PER (Polarization Extinction Ratio) >15 >15 >15 >15 >13 db Input fiber type Panda 980 Input fiber length 1 m Input fiber connector FC/APC Output fibre length typ. 50 cm Output fibre termination Collimated beam - Typical beam <1 mm Optical isolation Input, inter-stages and output - Beam quality M² <1.3 - Dimensions 3U 19 (448 x 451 x 132) mm³ Weight < 13 kg Storage / Operation Temperature - 0 to + 50 / + 15 to + 35 C Control mode ACC - Control interface Front panel or USB V Operating voltage AC 88 to 264 V Typ. power consumption (@ 25 C) <150 < 350<150 <250 <320 <350 W Options: - 10x beam expander - Customised specs on request - Extended warranty. Operating and safety considerations Manlight Fibre Amplifiers comply with CE, FDA & RoHS. All Manlight Fibre Lasers are patent pending. The Manlight Fibre Amplifiers emit both invisible Class IV and visible Class II radiations. Direct and scattered radiation can be harmful to the human eye. Proper laser safety eyewear must be worn during operation. Information in this document is subject to change without notice. Mechanical drawings: Manlight S.A.S. - 4, rue Louis de Broglie Lannion, France - sales@manlight-alcen.com ML-HED-1001-Rev.01

17 HED Product Line ML**-EYFA-CW-SLM-P-TKS Series Technical Specification: Ordering Information: MLxx-EYFA-CW-SLM-P-TKS xx = Average output power in Watts Parameter Value Unit Operation mode CW - Nominal Seed Laser Wavelength 1550 typ. nm Seed Laser Wavelegth Range nm Seed Laser Instantaneous Linewidth > 10 khz Nominal input power 25 mw Input power range mw Nominal output power (@ 25mW input) W Output power tunability % Long term stability (RMS, over 1h@25 C) <+/- 2 % Polarization Linear - PER (Polarization Extinction Ratio) >15 >15 >13 >13 db Input fiber type Panda 1550 Input fiber length 1 m Input fiber connector FC/APC Output fibre length typ. 50 cm Output fibre termination Collimated beam - Typical beam <1 mm Optical isolation Input, inter-stages and output - Beam quality M² <1.3 - Dimensions 3U 19 (448 x 451 x 132) mm³ Weight < 13 kg Storage / Operation Temperature - 0 to + 50 / + 15 to + 35 C Control mode ACC - Control interface Front panel or USB V Operating voltage AC 88 to 264 V Typ. power consumption (@ 25 C) <150 < 350<150 <250 <320 W Options: - 10x beam expander - Customised specs on request - Extended warranty. Operating and safety considerations Manlight Fibre Amplifiers comply with CE, FDA & RoHS. All Manlight Fibre Lasers are patent pending. The Manlight Fibre Amplifiers emit both invisible Class IV and visible Class II radiations. Direct and scattered radiation can be harmful to the human eye. Proper laser safety eyewear must be worn during operation. Information in this document is subject to change without notice. Mechanical drawings: Manlight S.A.S. - 4, rue Louis de Broglie Lannion, France - sales@manlight-alcen.com ML-HED-1001-Rev.01