Vectron International Filter specification TFS 243E 1/5

Transcription

1 Vectron International Filter specification TFS 243E /5 Measurement condition Ambient temperature T A: 23 C Input power level: 0 dbm Terminating impedance: * Input: 350 Ω -3.8 pf Output: 350 Ω -3.8 pf Characteristics Remark: The reference level for the relative attenuation a rel of the TFS 243E is the minimum of the pass band attenuation a min. The minimum of the pass band attenuation a min is defined as the insertion loss a e. The centre frequency f c is the arithmetic mean value of the upper and lower frequencies at the 3 db filter attenuation level relative to the insertion loss a e. The nominal frequency is fixed at MHz without any tolerance. The given values for both the relative attenuation a rel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency f c is shifted due to the temperature coefficient of frequency TC f in the operating temperature range and due to a production tolerance for the centre frequency f c. D a t a typ. value tolerance / limit Insertion loss a e.4 db max. 2.5 db (reference level) Nominal frequency MHz Centre frequency at ambient temperature f c MHz MHz Passband PB ± 25 khz Pass band ripple 0.5 db max. ±0.5 db Bandwidth BW 0.5 db - min. ± 25 khz 3 db 440 khz - Relative attenuation a rel ± 0.5 MHz ±.0 MHz 5 db min. 7 db ±.0 MHz ± 3.0 MHz 30 db min. 25 db ± 3.0 MHz ± 5.0 MHz 37 db min. 25 db ± 5.0 MHz ± 8.0 MHz 43 db min. 25 db ± 8.0 MHz ± 20.0 MHz 48 db min. 40 db Input power level - max. 5 dbm Operating temperature range OTR C Storage temperature range C Frequency inversion temperature T o +28 C - Temperature coefficient of frequency TC f** ppm/k 2 - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) = Generated: Checked / Approved:.

2 Vectron International Filter specification TFS 243E 2/5 Filter characteristic magnitude in db magnitude in db frequency in MHz Construction and pin connection (All dimensions in mm) S 243E J9 3 7,2 Max. 2,54 ± 0,2 2 Max. 2,54 ± 0, frequency in MHz Date code Input 2 Ground 3 Ground 4 Ground 5 Ground 6 Ground 7 Output 8 Ground 9 Ground 0 Ground Ground 2 Ground 5,2 Max. Date code: Year + week J 207 K 208 L ,80 50 Ω Test circuit L 7 SAW L2 2, 3, 4, 5, 6, 8, 9, 0,, 2

3 Vectron International Filter specification TFS 243E 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification:. Shock: 500 g, ms, half sine wave, 3 shocks each plane; DIN IEC T Vibration: 0 Hz to 2000 Hz, 0.35 mm or 5 g respectively, octave per min, 0 cycles per plane, 3 planes; DIN IEC T Change of temperature: 4. Resistance to solder heat (reflow): -55 C to 25 C / 5 min. each / 00 cycles DIN IEC part 2 4 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; 5. SAW devices are Electrostatic Discharge (ESD) sensitive devices. This filter is RoHS compliant (20/65/EU) Packing Tape & Reel: IEC 286 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader: min. 500 mm trailer: min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : /-0. Po : 4.00 ±0. Do : /-0 E :.75 ±0. F : 7.50 ±0. G(min) : 0.75 P2 : 2.00 ±0. P : 8.00 ±0. D(min) :.50 Ao : 5.40 ±0. Bo : 7.60 ±0. Ct : 3.30 ±0. Ko : 2.00 ±0. t : 0.30 ±0.05 t Ko Ct Do Typ Date Code PIN Marker W 2 Po D P P2 Ao Bo G G F E W Reel (all dimensions in mm) A : 330 or 80 W : /-0 W2(max) : N(min) : C : /-0.2 A C N W The minimum bending radius is 45 mm.

4 Vectron International Filter specification TFS 243E 4/5 Air reflow temperature conditions Conditions Exposure Average ramp-up rate (30 C to 27 C) less than 3 C / second > 00 C between 300 and 600 seconds > 50 C between 240 and 500 seconds > 27 C between 30 and 50 seconds Peak temperature max. 260 C Time within 5 C of actual peak temperature between 0 and 30 seconds Cool-down rate (Peak to 50 C) less than 6 C / second Time from 30 C to Peak temperature no greater than 300 seconds Temperature / C Chip-mount air reflow profile max. 260 C 27 C max. 300 s s s Time / s

5 Vectron International Filter specification TFS 243E 5/5 History Version Reason of Changes Name Date.0 Generation of development specification. Strehl db added. Strehl Generation of filter specification and typical values added. Sabah Insertion loss, bandwidth and relative attenuation updated. Strehl Stability characteristics updated..4 Relative attenuation corrected. Strehl Filter characteristic corrected. Strehl Centre frequency at ambient temperature including tolerances added. Schönbein Frequency inversion temperature added to data table. 2. Storage temperature range updated. Schönbein