HAWK Magnetostrictive Level Transmitter (CSA/FM, ATEX, IECEx)

Transcription

1 Heading Product Name A Higher Level of Performance Data Sheet HAWK Magnetostrictive Level Transmitter For more information, please visit >

2 Model HLT Transmitter with Analog Output and HART Product overview The Model HLT liquid level transmitter satisfies the demand for an analog communication interface for sightglass (bypass chamber) applications. The Model HLT transmitter provides a 4-20 ma output for most magnetic level gauge manufacturers and allows for mounting external to the chamber without interrupting the process. Model HLT transmitters are modular in design offering a selection of mounting options and pipe styles. The modularity also offers simple field replacement. Subject to local electrical codes, the sensing element and electronics can be removed from the transmitter pipe without disturbing the operation of the process saving both time and money. The model HLT transmitter uses HART communication for setup, calibration, and diagnostics. HART can be utilized via a hand-held communicator or with the HAWK setup software via a PC and HART to serial converter. The optional on-board display and keypad is also provided for local indication and programming. Features Applications Markets 4 to 20 ma Analog Output with HART No Scheduled Maintenance or Recalibration High Accuracy and Repeatability AMS Aware Explosion-proof and/or Intrinsically Safe Inventory Control Process Vessel Bypass Chamber Petroleum and Petrochemical Power Generation Specialty Chemical All specifications are subject to change. Contact HAWK for specifications and engineering drawings that are critical to your application. Drawings contained in this document are for reference only. 2

3 Product specifications Parameters LEVEL OUTPUT Specifications Measured Product level variable: Total Level or Interface Level Output signal / Protocol: 4 to 20 ma with HART Order length: Rigid pipe: 508 mm (20 in.) to 3658 mm (144 in.) Contact factory for longer lengths. Order length equals the measurement range plus the inactive zone. Non-linearity: 0.02% F.S. or mm (1/32 in.) * * Whichever is greater Repeatability: 0.01% F.S. or mm (0.015 in.) * (any direction) Contact factory for alternative materials. COMPATIBILI TY MRA3/4 chamber compatibility: ELECTRONICS Input voltage: Fail safe: Reverse polarity protection: Lightning/ Transient protection: CALIBRATION Zero adjust range: Span adjust range: HAWK K-Tek Jerguson Kenco Wika Klinger Quest-Tec Vize Penberthy Others 10.5 to 36.1 Vdc, 28 Vdc maximum for I.S. ATEX approval High (21.4 ma), or Low (3.8 ma) Series diode Stage 1: Line-to-ground surge suppression; IEC Stage 2: Line-to-line and line-to-ground transient suppressors; IEC Anywhere within the active length Full scale to 152 mm (6 in.) from zero Parameters ENVIRONMENTAL Enclosure rating: Humidity: Operating temperatures: FIELD INSTALLATION Housing dimensions: Specifications NEMA Type 4X 0 to 100% relative humidity, non-condensing Electronics: -40 C (-40 F) to 71 C (160 ºF) Sensing element: -40 C (-40 F) to C (257 F) Higher temperatures are available using a small insulation pad.. Contact factory for specific temperature ranges. Single cavity: 127 mm (5 in.) by 123 mm (4.85 in.) 121 mm (4.75 in.) O.D. MOUNTING Rigid pipe: Hose clamp to chamber WIRING Connections: 2-wire shielded cable twisted pair, ELECTRICAL CONNECTIONS Dual Single Compartment Cavity: Housings: ¾ in. conduit 3/4 in. opening, conduit opening, M20 M20 for for ATEX Version Single Cavity: 3/4 in. conduit version opening, M20 for ATEX Version DISPLAY Measured variables: Product level Size: 13 mm (0.5 in.) Number of digits: 16 3

4 Agency Approvals explosion proof FM 3615 C22.2 No. 30 Class I, Division 1, Groups B, C and D Class II, Division 1, Groups E, F and G Division 1, NEMA Type 4X Explosion-proof housing required 90 electronic mount is only for Groups C and D Intrinsically safe FM 3610 C22.2 No. 157 en Class I, Division 1, Groups A, B, C and D Class II, Division 1, Groups E, F and G Class III, T4 Division 1, NEMA Type 4X PTB 00 ATEX 2069X II 1/2 G bzw. II 2 G EEx ia IIB T4 bzw. EEx ia IIA T4 HART ART handheld communicator programming The Model HLT transmitter programming can also be performed by using handheld HART communicator device such as the Rosemount 375 or 475. Setpoint programming using the display Any Model HLT transmitter that is purchased with a display has the ability to adjust the 4 and 20 ma setpoints by pressing the appropriate button located at the bottom of the display. 4

5 Product dimensions and mounting HAWK offers the Model HLT transmitter configured for external mounting to most Magnetic Level Gauges (MLG) (see Figure 1 ). The Model HLT can be ordered with the standard 5/8 inch OD pipe or the optional 1/2 inch OD pipe from 508 mm (20 in.) to 3658 mm (144 in.). Stainless steel hose clamps are typically used to secure the Model HLT to the MLG. The Model HLT transmitter Measuring Range is equal to the Order Length minus the Inactive Zone. The Measuring Range should equal the measuring range of the MLG. Ensure that there are no obstructions that will limit the ability to mount the Model HLT on the MLG. Current Pulse Start pulse Magnetic Float Assembly 132 mm (5.19 in.) mm (8 in.) Sensor Wire Inactive Zone 95.3 mm (3.75 in.) Measuring Range Order length Inactive Zone 76.2 mm (3 in.) Figure 1 5

6 Product dimensions and mounting HAWK offers the Model HLT transmitter configured for external mounting to most Magnetic Level Gauges (MLG) (see Figure 2 ). The Model HLT can be ordered with the standard 5/8 inch OD pipe or the optional 1/2 inch OD pipe from 508 mm (20 in.) to 3658 mm (144 in.). Stainless steel hose clamps are typically used to secure the Model HLT to the MLG. The Model HLT offers an optional 90 degree fitting for an MLG with both top and bottom flanges. The 90 degree fitting allows the electronic head of the Model HLT to be positioned to the side of the pipe allowing for simpler mounting. The Model HLT transmitter Measuring Range is equal to the Order Length minus the Inactive Zone. The Measuring Range should equal the measuring range of the MLG. Ensure that there are no obstructions that will limit the ability to mount the Model HLT on the MLG. 2 ft ft Figure 2. Model MRA3/4 mounting, top and bottom flange Figure 2 6

7 Ordering information for FM-CSA approvals Agency Approvals 1 Model M Magnetostrictive Gauge 2 Type R Analog Transmitter 3 Approval Agency F FM FM 4 CSA CSA 4 Output ma High Gain w/ Display, 1 Loop All ma High Gain w/o Display, 1 Loop All B Single cavity (XP) 5 Housing Type C D Dual cavity (XP)* Single cavity (XP) w/ Display window All E Dual cavity (XP) w/ Display window* *Dual cavity requires electronic mount 90 degree bend 1 Integral Electronics All 3 90 degree bend, housing top left 6 Electronics Mounting 4 90 degree bend, housing top right 5 90 degree bend, housing bottom left 6 90 degree bend, housing bottom right All 7 Sensor Pipe B Industrial Pipe (5/8 in OD) All R Industrial Pipe (1/2 in OD) All 8 Material of Construction 1 316L SS 9 Process Connection Type X None 10 Process Connection Size X None 11 Temperature Element 0 None 12 Unit of measurement 13,14,15,16,17 Length 14 Special M U S E Metric US Customary XXX.XX Inches XXXXX mm Standard product Engineered Special (>144 w/ factory approval) 7

8 Ordering information for ATEX and IECEx approval Agency Approvals 1 Model M Magnetostrictive Gauge 2 Type R Analog Transmitter E ATEX Approval ATEX Ex d or Ex ia H IECEx Approval IECEx Ex d 3 Approval Agency B INMETRO Approval INMETRO Ex d K KC Approval KC Ex d P CCoE Approval CCoE Ex d 4 Output ma High Gain w/ Display, 1 Loop All ma High Gain w/o Display, 1 Loop All B Single cavity (XP) C D Dual cavity (XP)* Single cavity (XP) w/ Display window ATEX, IECEx, INMETRO, KC, CCoE, Ex d Only E Dual cavity (XP) w/ Display window* G Single cavity (XP) 5 Housing Type H J Dual cavity (XP)* Single cavity (XP) w/ Display window ATEX, Ex ia IIA K Dual cavity (XP) w/ Display window* R Single cavity (XP) S T Dual cavity (XP)* Single cavity (XP) w/ Display window ATEX, Ex ia IIB U Dual cavity (XP) w/ Display window* *Dual cavity requires electronic mount 90 degree bend 1 Integral Electronics All 3 90 degree bend, housing top left Ex d Only 6 Electronics Mounting 4 90 degree bend, housing top right Ex d Only 5 90 degree bend, housing bottom left Ex d Only 6 90 degree bend, housing bottom right Ex d Only 7 Sensor Pipe B Industrial Pipe (5/8 in OD) All R Industrial Pipe (1/2 in OD) All 8 Material of Construction 1 316L SS 9 Process Connection Type X None 10 Process Connection Size X None 11 Temperature Element 0 None 12 Unit of measurement M Metric U US Customary 13,14,15,16,17 Length 18 Special S E XXX.XX Inches XXXXX mm Standard Engineered Special (>144 w/ factory approval) 8

9 Programming and hardware accessories HARDWARE HarDWare PART Part NUMBER NuMBer Hart to rs-232 adapter (SMAR H1-311) FM APPROVED 9

10 HAWK, Since 1988 Hawk Measurement Systems Pty Ltd (HAWK) was established in It's founding members saw the universal requirement of various industries requiring improved process control and efficiency in their operations. We Can Help HAWK understands the difficulties customers face when seeking accurate level measurement. Every application is different, involving a multitude of environmental factors. This is where HAWK excels. Our aim is to ensure that customers not only feel comfortable with our technology, but that we also to ensure a consistent and reliable solution is in place for the long term. We believe that a combination of application and product expertise, as well as forward thinking and proactive support policies are the foundation of successful customer-supplier relationships. 10

11 Progressive Technical Support HAWK believes that the future of the Level Measurement Industry revolves around the quality of pre and post sales - support. Our aim is for all sales & support staff to be product experts, and more importantly application experts making our customers applications as efficient and consistent as possible. Remote Innovation HAWK understands the need for immediate technical assistance. Knowledge Sharing HAWK believes that knowledge sharing is key to creating long term relationships. Empowering our customers and our worldwide distribution network, whilst being available at all times to lend a helping hand, is the perfect recipe for long term solutions and relationships. HAWK openly extends an invitation to share our 25 years of level measurement experience, and ensure that your day to day processes are efficient, understood, and always working. The HAWKLink 3G communication device allows any computer with internet access and our free GosHawK diagnostic & calibration software; to dial in, calibrate, test, and check the performance of HAWK products. This innovative system allows our Global Support Team to assist with commissioning and after sales service of HAWK equipment worldwide. Measurement problems are addressed as they happen; not days or weeks later. 11

12 A Higher Level of Performance Hawk Measurement Systems Hawk Measurement (Head Office) 96 Glenn Street Maurice Court Lawrence, MA 01843, USA Nunawading VIC 3131, AUSTRALIA Phone: HAWKLEVEL ( ) Phone: Phone: Fax: Fax: info@hawk.com.au info@hawkmeasure.com For more information and global representatives: Represented by: DOC-MLT-ICSA-FM-DAT 0315