SOIL INSTRUMENTS BEAM ELECTROLEVEL, ELECTROLEVEL TILTMETER & HELM INSTALLATION MANUAL (Including Cable-Free sensor zeroing)

Size: px

Start display at page:

Download "SOIL INSTRUMENTS BEAM ELECTROLEVEL, ELECTROLEVEL TILTMETER & HELM INSTALLATION MANUAL (Including Cable-Free sensor zeroing)"

Ross Floyd
5 years ago
Views:

1 SOIL INSTRUMENTS BEAM ELECTROLEVEL, ELECTROLEVEL TILTMETER & HELM INSTALLATION MANUAL (Including Cable-Free sensor zeroing) Man 173 6(A5) 04/4/2006 C. Rasmussen Phil Day Chris Rasmussen Manual No. Revision Date Originator Checked Authorised for Issue 1

2 Contents Section 1 : Introduction...3 Section 2 : Installation Horizontal Beam & Sensor Installation Tiltmeter and Vertical Beam & Sensor Installation Digital Radio (Cable Free) Enabled Sensors Zeroing The Sensor Using The HELM Readout...9 Section 3 : Zeroing A Sensor Section 4 : Wiring...12 Section 5 : Data Reduction (A) For Linear ( 4mm) calibrations (B) For polynomial ( 12mm) calibrations...14 Appendix A.Sample Installation Record Sheet

3 Section 1 : Introduction This manual covers four related products; (1) The Soil Instruments Beam Electrolevel, (2) The Electrolevel Tiltmeter, (3) the HELM readout and (4) The Soil Instruments Radio enabled Electrolevel zeroing. The Beam Electrolevel is used to monitor vertical deflections (heave or settlement) and is mounted horizontally in beams typically 1 to 2.5 metres in length. The Electolevel Tiltmeter is designed to be either attached to a structure or a vertical beam and the HELM is a set up and readout tool for both Electrolevel products Pictured below is a horizontal electrolevel beam containing the Beam Electrolevel sensor. The electrolevel tiltmeter for attachment directly to a structure or vertical beam 3

4 The HELM (Hand Held Electrolevel Meter), the HELM reads all Soil Instruments Electroelevel products as well as up to 20VDC and 2K, making it an ideal all round site readout for a variety of instruments as well as a tool to check power supplies and lead / sensor continuity. The electrolevel tiltmeter with the Soil Instruments Digital Radio Transmitter fitted (a factory option) to form a Cable Free Tiltmeter 4

Section 2 : Installation The installation section of this manual is split into three sections; (a) Horizontal beam and sensor installation, (b) Tiltmeter direct and Vertical beam installation, and,

5 Section 2 : Installation The installation section of this manual is split into three sections; (a) Horizontal beam and sensor installation, (b) Tiltmeter direct and Vertical beam installation, and, (c) sensor zero setting (common to both sensor types). The wiring is also common and dealt with in the wiring chapter Horizontal Beam & Sensor Installation The nominal beam length will have been specified at time of order, a parts list for a single beam installation is detailed thus; - Horizontal beam with end fittings - Horizontal beam sensor (may be already fitted into beam) - Two anchor end kits These parts are pictured below The installation sequence is; (1) drill mounting holes and fit anchors, (2) attach and level beam (3) zero sensor. The anchor kit supplied by Soil Instruments has either and expanding shell M10 anchor or a groutable M10 anchor. Both require an 11mm or 12mm hole to be drilled approx 60mm deep into the structure to be monitored. Hold the beam up against the structure with a spirit level along the top face, level and mark the centre of each end fitting, remove the beam and drill two holes to approx. 60mm depth. If using an expanding shell anchor, insert and set with the supplied tool. If using a groutable anchor, grout and wait the required time for setting (with quick set grout such as Hilti HIT-C this is approx minutes) 5

Before installing the beam, fit the sensor into the beam (if not already there) and check that the two retaining screws through the back of the beam to the sensor are tight.

from the wall outwards. Back nut, washer, beam end fitting, plastic washer, washer, nylock nut.

6 Before installing the beam, fit the sensor into the beam (if not already there) and check that the two retaining screws through the back of the beam to the sensor are tight. The anchor kit has a series of nuts and washers, to ensure that longitudinal thermal expansion of the beam does not cause spurious readings, these must be fitted in the correct order, detailed below, from the wall outwards. Back nut, washer, beam end fitting, plastic washer, washer, nylock nut. The nylock nut should only be tightened so it just compresses the spring washer, a drawing of the correct sequence is below for both a single and a pair of beams (where a pair will share end fitings) Right, single beam end fitting, far right a pair of beams sharing a single mounting stud (note extra washer between beams) Once the anchors are in place and the beam fitted, check with a spirit level that both horizontal axis of the beam are level (i.e. both along and across the beam), it may be necessary to loosing the large bolt which attaches the end fitting to the beam by approx. 1 turn and rotate the beam to achieve the across level. Once level, carefully retighten the end fitting bolts. Repeat the above for further beams, sharing end fittings as shown above if it is desired to fit two beams to a single mounting stud. Before zeroing the sensors, it is desirable to run the cables to the datalogger or readout point, but not to make the connection to the sensor. It is permissible to attach cables to beams, but slack cable must be left (by forming a small omega loop) at the joint between a pair of beams to allow for movement. Once all of the above is complete the beam can be set to zero, see section C of the installation chapter and then wired, see the wiring chapter. 6

2.02 Tiltmeter and Vertical Beam & Sensor Installation The Tiltmeter has two uses, it can be fitted directly to the structure for vertical settlement / heave monitoring, or onto a vertical beam for

7 2.02 Tiltmeter and Vertical Beam & Sensor Installation The Tiltmeter has two uses, it can be fitted directly to the structure for vertical settlement / heave monitoring, or onto a vertical beam for lateral deflections. To fix directly to a structure, hold the tiltmeter against the structure, with a spirit level on top and mark the location of the two fixing holes. The tiltmeter can be fixed using expanding plastic anchors such as Rawlbolts, expanding shell anchors, or groutable anchors. Ensure that the anchor head bolt (whichever method is used) has a washer between it and the tiltmeter mounting plate. A typical installation is shown right of a Tiltmeter attached to a brick wall The tiltmeter can also be attached to a vertical beam, the nominal beam length will have been specified at time of order, a parts list for a single beam installation is detailed thus; - Vertical beam with end fittings - Vertical tiltmeter with fitting kit (may be already fitted onto beam) - Two anchor end kits (must be vertical anchor kits) The installation sequence is; (1) drill mounting holes and fit anchors, (2) attach and level beam (3) zero sensor. The anchor kit supplied by Soil Instruments has either and expanding shell M10 anchor or a groutable M10 anchor. Both require an 11mm or 12mm hole to be drilled approx 60mm deep into the structure to be monitored. Hold the beam up against the structure with a spirit level along the side face, level and mark the centre of each end fitting, remove the beam and drill two holes to approx. 60mm depth. If using an expanding shell anchor, insert and set with the supplied tool. If using a groutable anchor, grout and wait the required time for setting (with quick set grout such as Hilti HIT-C this is approx minutes) 7

Before installing the beam, fit the sensor into the beam (if not already there) and check that the two retaining screws on the rear of the tiltmeter mounting bracket are tight and that once installed

The anchor kit has a series of nuts and washers, to ensure that longitudinal thermal expansion of the beam does not cause spurious readings, these must be fitted in the correct order, detailed below,

The nylock nut should only be tightened so it just compresses the spring washer, a drawing of the correct sequence is below for both a single and a pair of beams (where a pair will share end fitings)

8 Before installing the beam, fit the sensor into the beam (if not already there) and check that the two retaining screws on the rear of the tiltmeter mounting bracket are tight and that once installed the tilmeter sensitive axis will be correctly orientated. The anchor kit has a series of nuts and washers, to ensure that longitudinal thermal expansion of the beam does not cause spurious readings, these must be fitted in the correct order, detailed below, from the wall outwards. Back nut, washer, beam end fitting, washer, spring washer, nylock nut. The nylock nut should only be tightened so it just compresses the spring washer, a drawing of the correct sequence is below for both a single and a pair of beams (where a pair will share end fitings) Right, single beam end fitting, far right a pair of beams sharing a single mounting stud (note extra washer between beams) Once the anchors are in place and the beam fitted, check that the tiltmeter is at 90 to the structure to be monitored, it may be necessary to loosing the large bolt which attaches the end fitting to the beam by approx. 1 turn and rotate the beam to achieve the across level. Once level, carefully retighten the end fitting bolts. Repeat the above for further beams, sharing end fittings as shown above if it is desired to fit two beams to a single mounting stud. Before zeroing the sensors, it is desirable to run the cables to the datalogger or readout point, but not to make the connection to the sensor. It is permissible to attach cables to beams, but slack cable must be left (by forming a small omega loop) at the joint between a pair of beams to allow for movement. Once all of the above is complete the beam can be set to zero, see section C of the installation chapter and then wired, see the wiring chapter. 8

9 2.03 Digital Radio (Cable Free) Enabled Sensors These are installed in exactly the same way as the standard (HELM or Datalogger readout sensors) the zeroing sequence is also the same as the standard product. The only difference is that there is no cable to a readout point or datalogger. Please see section 2.04 below for details on zeroing the Cable Free option. For reading the cable free sensors, please refer to manual 183, available from Soil Instruments and supplied with Digital Radio Cable Free Readouts Zeroing The Sensor Using The HELM Readout The electrolevel sensor used in the beam sensor and the tiltmeter is a narrow angle, high accuracy device. As such it must be set to zero when installed to both allow maximum range for the monitoring to take place and to maximise the insensitivity to temperature variations. This task is simply achieved using the Soil Instruments HELM readout. The HELM has two switches, which select the following; Left Hand Switch Off/On Electrolevel Volts (0-20VDC) Ohms (0-2k Right Hand Switch Backlight Off Backlight On Sounder On Backlight and Sounder On A full explanation of each function is below:- Left Hand switch Off/On - Switches HELM off or on regardless of position of right hand switch position Electrolevel (symbol) - Places HELM into electrolevel read mode, right hand switch allows selection of backlight and sounder Volts (symbol) - Selects voltmeter mode, the HELM can read 0-20VDC with an accuracy of 20%FS Ohms (symbol) - Selects Ohms mode, the HELM can read 0-2k with an accuracy of 2%FS 9

10 Right Hand switch Off - Backlight and sounder are off Backlight (symbol) - Switches on display backlight for use in tunnels and at night Sounder (symbol) - Turns on an audible tone which increases in volume as zero is approached on an electrolevel sensor. Allows for the sensor zero to be set without the need to view the display. Backlight & Sounder (Symbol) - Turns both the backlight and the sounder on. Note, battery life will be shortened if the HELM is continuously run in this mode 10

Section 3 : Zeroing A Sensor To zero a sensor, proceed as follows.

switch the HELM on and select electrolevel mode with the desired combination of sounder and backlight.

as possible. It is desirable to set the sensor to within 10 digits of zero, which equates to approx.

When the zero has been set, withdraw the lead from the HELM and apply a small amount of acrylic varnish (such as

11 Section 3 : Zeroing A Sensor To zero a sensor, proceed as follows. Connect the lead supplied with the HELM to the small blue jack socket on the PCB adjacent to the sensor housing, switch the HELM on and select electrolevel mode with the desired combination of sounder and backlight. (see pictures above) Use the two adjuster screws, in unison to bring the reading on the display as close to zero as possible. It is desirable to set the sensor to within 10 digits of zero, which equates to approx. 20 arc seconds (0.097mm/metre) from absolute sensor zero. Take care not to overtighten the two adjuster screws. When the zero has been set, withdraw the lead from the HELM and apply a small amount of acrylic varnish (such as nail polish) to lock the screws against vibration. To zero the Cable-Free sensors, proceed as above, but ensure the radio is both switched on and not in fast read mode (see manual Man-183) 11

12 Section 4 : Wiring Soil Instruments electrolevel products require precise AC excitation and must be read with the same type of readout with which they were calibrated. The factory calibration is carried out with a Campbell CR10 datalogger the data from this being used to derive the HELM calibration factors. Therefore Soil Instruments only recommends and supports our electrolevel products when read with a Campbell CR10 logger or a HELM. The sensors can be read by simply plugging the HELM into the connector on the sensor PCB, in which case no external wiring is required. Alternatively, cables can be run to a central switch box from where HELM readings can be taken. The wiring for the external switch box/helm option is contained in the manual supplied with the switch box, this manual concerns wiring to a CR10 based system only. If the CR10 has been supplied by Soil Instruments, it will have a wiring diagram included within it. If others are supplying the CR10 and writing the read/log program then the table below contains the information they need to connect sensors to either/or a CR10/AM416/AM16/32 and the P program instruction ranges. If in doubt we highly recommend that Soil Instruments are contacted for advice and a logging program. Connector Strip On PCB Function Pin 1 (Top) Excitation (CR10 E1/H1) Pin 3 (Third From Top) Output (CR10 L1) Pin 4 (Bottom) Ground (CR10 AG) Parameter Range Excitation Campbell CR10 Instruction Fast P5 AC half bridge Voltage 2500mV (15) Input 2500mV (15) Multiplier 10 It is mandatory to use a cable which conforms to Belden 9927 specifications, Soil Instruments 4C cable is ideal. No guarantee of performance can be made or given unless this requirement is adhered to. The comments below in respect of temperature effects on cable and long cable runs apply only to Belden 9927 specification cable. Soil Instruments has extensive data on the effects of cable lengths with electrolevel sensors. The sensor used has a relatively high resistance/impedance in comparison with the cable, thus cable runs between sensor and datalogger/readout box of up to 250 metres may be used. The same resistance/impedance relationship exits for change in cable properties due to temperature, a temperature range (over a year) of up to 70 C is tolerated without the need for additional precautions. 12

13 Section 5 : Data Reduction Two calibrations are available. These are based on two tilt ranges, a narrow angle range resulting in a linear (slope and offset) calibration and a wider angle range resulting in a 5 th order polynomial calibration. Depending on the expected range of movement and the accuracy required, the user selects which calibration to use. The table below contains details of these calibrations. Sensor Type Range (mm/metre) Range (arc degrees) Hz Beam arc minutes Tiltmeter arc minutes Hz Beam arc minutes Tiltmeter arc minutes Calibration Type Accuracy arc degrees Accuracy mm Linear mm Linear mm Polynomial mm Polynomial mm In all cases, mm equates to current read x calibration factor(s) less initial reading x calibration factor(s). Examples for both are given below (A) For Linear ( 4mm) calibrations Delta mm = (current reading x Sf)-(initial reading x Sf) x Gauge Length Where Sf is the calibration factor from the calibration certificate For example, where an initial reading is 5.001, current reading is 5.202, the gauge length is 1.5 metres and Sf is the formula would calculate as follows mm = (5.202 x ) - (5.001 x ) x 1.5 ( ) - ( )x1.5 = mm A positive resultant indicates the right hand end of the sensor is moving up (rotating counter clockwise), a negative result indicates the left hand end of the sensor is moving up (clockwise rotation). Do not apply gauge length multiplication factors to tiltmeters mounted directly onto a structure, only when they are fixed to a vertical beam. 13

14 5.02 (B) For polynomial ( 12mm) calibrations It is recommended that the application of polynomial function calibration factors are carried out (or at least set up by) someone who has an understanding of advanced mathematics. Soil Instruments cannot provide technical support for a lack of understanding of the process of this type of mathematical function. Delta mm = (current reading x [b o + b 1 X + b 2 X 2 + b 3 X 3 + b 4 X 4 + b 5 X 5 ]) - (initial reading x [b 0 + b 1 X + b 2 X 2 + b 3 X 3 + b 4 X 4 + b 5 X 5 ]) x Gauge Length Where X is the sensor data and b 0,b 1,b 2,b 3,b 4 & b 5 are the polynomial factors from the calibration certificate For example, where an initial reading is 5.001, current reading is 5.202, the gauge length is 1.5 metres, bo is , b1 is , b2 is , b3 is , + b4 is and b5 is , the formula would calculate as follows: mm = ( x 5.202) + ( x ) + ( x ) + ( x ) +( x ) ( x 5.001) + ( x 25.01) + ( x ) + ( x ) +( x ) x 1.5 = mm A positive resultant indicates the right hand end of the sensor is moving up (rotating counter clockwise), a negative result indicates the left hand end of the sensor is moving up (clockwise rotation). Note that in the examples given above, the difference between the linear and polynomial calibrations, when reduced by the raw data example, is less than 0.012mm/metre. A sample calibration certificate showing these values for sensor serial number 5908 is shown at the end of this manual. It is recommended that if the polynomial factors are to be used, then a spreadsheet is set up with pages for raw data, calibration factors, processed data and delta mm data. In this was a simple cut and past exercise will enable quick and easy application of the polynomial function with little chance for errors, a sample spreadsheet is available from Soil Instruments. If a fully automated program, such as I-Site is used, then the application of the polynomial function will become part of that package and errors will then be reduced to an absolute minimum. 14

15 Appendix A. Sample Installation Record Sheet EL Beam / Tiltmeter Installation Record Sheet Date Installer Site Location Length Location Sensor Number String No: Hz/V/Tilt No: Of Sensors Serial Number Gauge Length Channel Notes 15

Mems Tiltmeter (IPI Sensor Based) User Manual. Man /08/2014 Final Chris Rasmussen Phil Day

Mems Tiltmeter (IPI Sensor Based) Man193 2.0.2 07/08/2014 Final Chris Rasmussen Phil Day Manual No. Revision Date Originator Checked Authorised for Issue 1 Contents Section 1 : Section 2 : Introduction...