DR/2000 and DR/2010 Spectrophotometer
|
|
|
- Elfrieda McCarthy
- 6 years ago
- Views:
Transcription
1 DR/2000 and DR/2010 Spectrophotometer Wavelength Calibration Adjustment Purpose These instructions provide a step-by-step procedure for performing a wavelength calibration adjustment for the DR/2000 Spectrophotometer (software versions 2.0, 2.2, 3.0 and greater) and DR/2010 Spectrophotometer. Do not perform this procedure if your instrument has or 1.27 software! Perform the adjustment any time the lamp assembly (Cat. No ) is replaced and periodically for optimum performance. The adjustment assures the best possible accuracy and repeatability. Use the Calibration Filter Assembly (Cat. No ) to make the adjustment. Start by following the three steps below. Then choose the step-by-step instructions that apply to the specific instrument and software you are using to finish the calibration adjustment. 1. If lamp replacement is necessary, see the Lamp Replacement instructions shipped with the lamp. 2. Determine which software version applies to the spectrophotometer being adjusted. For the DR/2010 Spectrophotometer, the software version will briefly appear after the instrument is turned on. For the DR/2000 Spectrophotometer, different messages will appear, depending on the software in the instrument (see Table 1): DR/2000 Software Version Table 1 DR/2000 Messages Indicating Software Versions Display 2.0 or 2.2 If the first display is Method #?, pressshift CONFIG/METH, then enter 888 with the numeric keys. Press READ/ENTER. The display will show V2.0 or V and greater Self-Test V3.X and 1.27 DO NOT perform the calibration adjustment. Monochromator calibration could be permanently lost (Hach Service cannot restore the calibration). Select the appropriate wavelength calibration adjustment procedure on the following pages and continue.
2 DR/2010 Spectrophotometer Procedure 1. Empty the cell compartment and close the cover. Adjust the wavelength to about. 2. Press SHIFT SETUP/2 to enter the Setup Menu. Press the DOWN ARROW twice to access Lamp:. Ifin Momentary mode, press ENTER then UP ARROW, then ENTER again. If in Constant- On mode, go to step Scroll to the Adjust nm option with the UP ARROW key and press ENTER. The display will show: Peak Filter: 4. Press: ENTER.The display will show: Zero Required 5. Press: ENTER 100 %T Peak Filter 6. Insert the calibration filter into the cell compartment with the tab facing right. Close the cover. 7. Slowly adjust the wavelength by turning the control counterclockwise. Record the wavelength where the % transmittance reading is greatest. 8. Turn the wavelength control clockwise so the wavelength is at least 10 nm higher than the wavelength value recorded in step 7. 2
3 To use factory default setting, see instructions below this box. 9. Slowly turn the wavelength control counterclockwise. Watch the %T values displayed. Stop exactlyonthe highest transmittance. 10. Press: ENTER Are You Sure? 11. Press: ENTER The calibration adjustment will occur automatically. If successful, the display will show Completed and then Adjust nm. If you cannot obtain a good adjustment, contact the Hach Service center serving you. 12. To use the factory default setting, press SHIFT SETUP, then press UP ARROW twice. The display shows Adjust nm:.pressenter. PressUP ARROW once to display Default Setup:, thenenter. The display shows Completed.PressEXIT twice to get the Enter Program # prompt. DR/2000 Spectrophotometer Procedure, Version 3.0 and Greater 1. Press: SHIFT CONFIG/METH If CONSTANT ON is displayed, go to step 2. If MOMENTARY is displayed, press READ/ENTER to toggle to CONSTANT ON. 2. Press CONFIG/METH twicetoreturntothe METHOD #? prompt. 3. Press SHIFT % T to select the %T mode. The display will read: %T 4. With the cell compartment empty and the cover closed, rotate the wavelength dial until the small display shows: 1. Do not do this calibration if your instrument has version or 1.27 software! 3
4 5. Press: CLEAR/ZERO %T Note: If the display does not read within ±0.3 %T, press CLEAR/ZERO again. 6. Place the Calibration Filter into the cell holder. Close the cover. Note: Alignthetabwiththe notch in the cell holder opening. 7. Slowly turn the wavelength dial counterclockwise (decreasing wavelength). Record the wavelength where the %T is highest. 8. Turn the wavelength control clockwise so the wavelength is at least 10 nm higher than the wavelength value recorded in step Slowly turn the wavelength control counterclockwise. Watch the %T values displayed. Stop exactly on the highest transmittance. 10. Press SHIFT CONFIG/METH and scroll with the Arrow keys until the display shows: ADJUST nm 11. Press: READ/ENTER ARE YOU SURE? Press READ/ENTER again. If the wavelength calibration adjustment was successful, the display will show: COMPLETED with 808 in the nm field and then: ADJUST nm If you cannot obtain a good adjustment, contact the Hach Service center serving you. 12. Press CONFIG/METH three times to return the display to: METHOD #? 4
5 DR/2000 Spectrophotometer Procedure, Versions 2.0 and Press: SHIFT CONFIG/METH Scroll with the Arrow keys until the display shows: 2. Press READ/ENTER three times to accept the mode choice and return to the METHOD #? prompt. 3. Press SHIFT %T to select the %T mode. The display will show: %T 4. With the cell compartment empty and the cover closed, rotate the wavelength dial until the small display shows: CONSTANT ON Note: Do not do this calibration if your instrument has or 1.27 version software! 5. Press: CLEAR/ZERO 100.0% T Note: If the display does not read within ±0.3 %T, press CLEAR/ZERO again. 6. Place the Calibration Filter into the cell holder. Close the cover. Note: Align the key with the notch in the cell holder opening. 7. Slowly turn the wavelength dial counterclockwise (decreasing wavelength). Record the wavelength where the %T is highest. 8. Turn the wavelength control clockwise so the wavelength is at least 10 nm higher than the wavelength value recorded in step 7. 5
6 9. Slowly turn the wavelength control counterclockwise. Watch the %T values displayed. Stop exactlyonthe highest transmittance. 10. Press: SHIFT CONFIG/METH Enter 888 with the numeric keys. 11. Press READ/ENTER and immediately key in 123and READ/ENTER. If the calibration was successful, the display will show 808 in the nm field with the METHOD #? prompt. If you cannot obtain a good adjustment, contact the Hach Service center serving you. Hach Company, All rights reserved. Printed in the U.S.A. hm/dk 6/99 1ed
DPC-10. DPC-10 Software Operating Manual. Table of Contents. Section 1. Section 2. Section 3. Section 4. Section 5
Table of Contents Section 1 Section 2 Section 3 Section 4 Section 5 About the Software Test Function Programming Functions Connections Basic Mode Connection RC Mode Connection Using the DPC-10 Test Functions
UV-Vis-NIR Spectrophotometer Quick Start Guide
UV-Vis-NIR Spectrophotometer Quick Start Guide The following instructions are provided as a Quick Start Guide for powering up, running measurements, and shutting down the Lambda 950 UV-Vis Spectrophotometer.
Initial Power-Up Tests
Initial Power-Up Tests The signal generator will not function properly until the blank EEPROM has been programmed with a set of default values. The CPU will accomplish this task if the RxTx control line
I.D.A. Operation manual
TRX-200 Wide ide Band Receiver Operation manual Thank you for purchasing the TRX-200 all modes wide band monitoring receiver. Please read this operating manual carefully to avoid miss operation of the
Z-Truck Up-and-Down Motion. Y-Truck Side-to-Side Motion. Head. Squaring Plate. Sliding Plate FIGURE 1: THE CARVEWRIGHT MACHINE
Setup and use of CarveWright CO2 Powered Dragster Jig The CO 2 powered Dragster Jig will arrive from the factory fully assembled, calibrated, and squared. In order to get the best results, your CarveWright
Automated Double Aperture Accessory
For the Cary 1, 3, 100, 300, 4, 5, 400, 500, 500i, 4000, 5000, 6000i, Deep UV Installation Category II Pollution Degree 2 Equipment Class I Table of Contents Introduction Theory Operation Installation
1 Radar calibration at first installation
1 Radar calibration at first installation At first installation is necessary to properly calibrate the radar. This includes: Heading Line Transmission Trigger Delay Antenna Parking Position (only MDS 9
Laser LAX 300 G. Operating instructions
Laser LAX 300 G en Operating instructions A1 4 3 2a 1a 2b 8 4 5 9 1b 6 7 A2 A3 11 10 A4 A5 A6 L1 ± 0,3 mm/m ± 23/64 A7 L1 ± 0,3 mm/m ± 23/64 L2 ± 1/4 ± 0,2 mm/m B1 B2 90 C1 C2 C3 C4 X1 X2 X3 5m 5m S
COFFEE LABORATORY. Operators Manual COFFEE PRO MOISTURE MAC
COFFEE LABORATORY Operators Manual COFFEE PRO MOISTURE MAC Contents Page Components... 10-1 Error messages... 10-1 Operating conditions... 10-2 Screen and button Information... 10-3 Moisture testing procedure...
Dear Dark Fire owner,
Dear Dark Fire owner, One of the best aspects of Dark Fire is that it is software-based. As the Dark Fire community makes suggestions, and Gibson enhances functionality, these changes can be incorporated
Borders. Use QuiltMotion Touch for BERNINA to create a variety of border styles. Quick Borders. Borders using Simple Block Designs
Borders Use QuiltMotion Touch for BERNINA to create a variety of border styles. Quick Borders Borders using Simple Block Designs Clockwise and Counter Clockwise Borders Clockwise and Counter Clockwise
OTHER RECORDING FUNCTIONS
OTHER RECORDING FUNCTIONS This chapter describes the other powerful features and functions that are available for recording. Exposure Compensation (EV Shift) Exposure compensation lets you change the exposure
MicroLab 500-series Getting Started
MicroLab 500-series Getting Started 2 Contents CHAPTER 1: Getting Started Connecting the Hardware....6 Installing the USB driver......6 Installing the Software.....8 Starting a new Experiment...8 CHAPTER
SPECTRONIC Standards User Guide
SPECTRONIC Standards User Guide The information in this publication is provided for reference only. All information contained in this publication is believed to be correct and complete. Thermo Fisher Scientific
STANDARD OPERATING MANUAL Rev
STANDARD OPERATING MANUAL Rev. 5-31-12 (Software Version: 05-31-12) Coastal Amusements, Inc. 1950 Swarthmore Ave. Lakewood, NJ 08701 +1 (732) 905-6662 sales@coastalamusements.com http://www.coastalamusements.com
Laser LAX 300. Operating instructions
Laser LAX 300 en Operating instructions A1 4 3 2a 1a 2b 8 4 5 9 1b 6 7 X1 X2 X3 5m 5m S = 5m X X S = 5m Y X Y3 Y1 Y2 X Y en Operating instructions The STABILA LAX 300 is an easy to use crossed line and
Setting Part Zero and Setting Cutting Tool for Wheel Lathe
There are three sections in this document: A: Setting Tool #1 and Tool #2 on center line height to the spindle which are explained in steps 1 thru 3 B: Setting Part 0 for X & Z and setting X & Z reference
Solving the Rubik s Cube
Solving the Rubik s Cube The Math Behind the Cube: How many different combinations are possible on a 3x3 cube? There are 6 sides each with 9 squares giving 54 squares. Thus there will be 54 53 52 51 50
Cricut Design Space App for ipad User Manual
Cricut Design Space App for ipad User Manual Cricut Explore design-and-cut system From inspiration to creation in just a few taps! Cricut Design Space App for ipad 1. ipad Setup A. Setting up the app B.
CCG Referral App - Northern Ireland
CCG Referral App - Northern Ireland For practices in Northern Ireland who use the Referral Screen supplied by the CCG, the way you access the screen has been updated. A Vision App has been created to enable
Operation Guide 3721
MA0410-EA Modes and Hand Movement Each press of the B button sounds a confirmation tone and cycles through available modes in the sequence shown below. The watch will revert to the Timekeeping Mode automatically
Installing the detector filter assembly (G )
s1 Installing the detector filter assembly (G1600-62700) The detector filter transmits light of a defined wavelength range. Figure 1 shows a typical transmission spectrum. Maximum transmission is between
Vernier SpectroVis Plus Spectrophotometer (Order Code: SVIS-PL)
Vernier SpectroVis Plus Spectrophotometer (Order Code: SVIS-PL) SpectroVis Plus is a portable, visible to near-ir spectrophotometer and fluorometer. What is included with the SpectroVis Plus? One SpectroVis
Instruction Manual. B Series Program Mode (BLDC Servos)
Introduction Instruction Manual Congratulations on the purchase of the HFP-30. The HFP-30 is designed to program all Hitec Digital Programmable Servos (D Series, 5xxx/7xxx, and Brushless) as well as test
ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012
ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012 Introduction The KX3 standard VFO temperature compensation is entirely adequate for most
DXXX Series Servo Programming...9 Introduction...9 Connections HSB-9XXX Series Servo Programming...19 Introduction...19 Connections...
DPC-11 Operation Manual Table of Contents Section 1 Introduction...2 Section 2 Installation...4 Software Installation...4 Driver Installastion...7 Section 3 Operation...9 D Series Servo Programming...9
OTHER RECORDING FUNCTIONS
OTHER RECORDING FUNCTIONS This chapter describes the other powerful features and functions that are available for recording. Exposure Compensation (EV Shift) Exposure compensation lets you change the exposure
Software Manual for the Economy LBIC Demo
printed organic photovoltaics solar testing euipment specialty materials Software Manual for the Economy LBIC Demo Introduction This demonstration program is meant to show the capabilities of the infinitypv
Panorama TELEPACK 608
Quick Reference Guide Datascope Panorama TELEPACK 608 SpO 2 Panorama_Telepk QRG_0003_rB.indd 1 Note: The Panorama Telepack SpO 2 Quick Reference Guide is not intended as a replacement to the Operating
ADMS-847 Programming Software for the Yaesu FT-847
for the Yaesu FT-847 Memory Types Memories Limit Memories VFO A VFO B Home Satellite Memories One Touch Memory Channel Functions Transmit Frequency Offset Frequency Offset Direction CTCSS DCS Skip The
BATTERY GRIP INSTRUCTION MANUAL
BG-D700 BG-D90 BATTERY GRIP INSTRUCTION MANUAL Product Diagram 1- Contact Cap 2- Holder for Nikon dslr Signal Contact Cover 3- Signal Contacts 4- Auto-Focus Button 5- Main Control Dial 6- Multi-Selector
AA-35 ZOOM. RigExpert. User s manual. Antenna and cable analyzer
AA-35 ZOOM Antenna and cable analyzer RigExpert User s manual . Table of contents Introduction Operating the AA-35 ZOOM First time use Main menu Multifunctional keys Connecting to your antenna SWR chart
FILM SCANNER P Instruction Manual
FILM SCANNER P16-41458 Instruction Manual CONTENTS Safety Precautions 0 Features & Package Contents 1 Description of Parts 2 Loading Slides 3 Loading Negatives 4 Scanning Slides or Film 5-9 Transferring
Guide to Confocal 5. Starting session
Guide to Confocal 5 Remember that when booking and before starting session you can check for any problems at https://www.bris.ac.uk/biochemistry/uobonly/cif/index.html Starting session Switch on microscope
Instant Engagement Pair Structures. User s Manual. Instant Engagement 2011 Kagan Publishing
Instant Engagement Pair Structures User s Manual Instant Engagement 2011 Kagan Publishing www.kaganonline.com 1.800.933.2667 2 Instant Engagement Pair Structures Table of Contents GAME OVERVIEW... 3 Setup...3
A3 Pro INSTRUCTION MANUAL. Oct 25, 2017 Revision IMPORTANT NOTES
A3 Pro INSTRUCTION MANUAL Oct 25, 2017 Revision IMPORTANT NOTES 1. Radio controlled (R/C) models are not toys! The propellers rotate at high speed and pose potential risk. They may cause severe injury
Precision Pipeline Locator System User Guide. Rev
Precision Pipeline Locator System User Guide Rev 0 04.2001 TABLE OF CONTENTS Title SAFETY NOTES INTRODUCTION... 1 PPL RECEIVER... 1 PPL BAR... 1 PCM TRANSMITTER... 1 PPL RECEIVER FEATURES... 2 RECEIVER
BASIC IMAGE RECORDING
BASIC IMAGE RECORDING BASIC IMAGE RECORDING This section describes the basic procedure for recording an image. Recording an Image Aiming the Camera Use both hands to hold the camera still when shooting
Seized Drugs Operational Guidelines for the Thermo FTIR Comparative and Analytical Division
Operational Guidelines for the Thermo FTIR Comparative and Analytical Division THERMO FOURIER TRANSFORM INFRARED (FTIR) SPECTROMETER Instrument Nicolet 4700 Series FTIR spectrometer (Serial Number AFZ0400253)
Universal Camera Registration User Guide for ILS 9.75 & 12.75
User Guide for ILS 9.75 & 12.75 www.ulsinc.com Overview Camera Registration allows the laser system to automate the alignment of a vector path with the material for the purpose of tightening process control
CC200 USER S MANUAL. MANUAL NO. CC200m-UM-151 CH 1. PRIOR TO USE INDEX CH 3. CRAFT ROBO CONTROLLER PREFACE. Appendix A. Standard Specifications
CC200 USER S MANUAL MANUAL NO. CC200m-UM-151 PREFACE Thank you for purchasing the Craft ROBO CC200. Based on cutting-plotter technology developed by Graphtec over many years, CC200 provides outstanding
Laser LA-4P. Operating instructions
Laser LA-4P GB Operating instructions A 1 2 3a 5 3c 3b 3a 4 11 11 6 10 7 14a 14b 14c 12 9 8 B C 2. 1. D E F Ø 50mm - 115 mm Ø 2-4,5 G I K s > 6m > 20ft L M N P1 Q O 13 P2 GB Operating instructions The
Calibration Instruction Manual Emerson 475 Field Communicator. Manual Revision FC.2
Calibration Instruction Manual Emerson 475 Field Communicator Manual Revision FC.2 ABM 2 Wire Radar with HART ABM Sensor Technologies Inc 2013, all rights reserved. Emerson is a registered trademark of
What s in the pack? Getting Started - Initial Setup of Head Unit. Pairing a Remote
V0.02 What s in the pack? Remote Key: 1 - Menu 6 - Station Right 2 - Add/Delete 7 - Preset Down 3 - Preset Up 8 - Scan 4 - Station Left 9 - On/Off 5 - OK Getting Started - Initial Setup of Head Unit On
Connevans. DeafEquipment.co.uk. This product may be purchased from Connevans Limited secure online store at
Connevans Solutions to improve the quality of life This product may be purchased from Connevans Limited secure online store at www.deafequipment.co.uk DeafEquipment.co.uk Solutions to improve the quality
Step 1: Set up the variables AB Design. Use the top cells to label the variables that will be displayed on the X and Y axes of the graph
Step 1: Set up the variables AB Design Use the top cells to label the variables that will be displayed on the X and Y axes of the graph Step 1: Set up the variables X axis for AB Design Enter X axis label
RISK OF SHOCK: DO NOT WIPE DOWN ANY ELECTRICAL COMPONENTS. ALWAYS KEEP AWAY FROM ALL AREAS WHERE ELECTRONIC COMPONENTS ARE INSTALLED.
Maintenance General Cleaning Waste material from the printing process can accumulate inside the printer. Using a slightly damp, lint-free cloth, wipe the interior of the CubePro including the print plate,
CAST Application User Guide
CAST Application User Guide for DX900+ Electromagnetic Multilog Sensor U.S. Patent No. 7,369,458. UK 2 414 077. Patents Pending 17-630-01-rev.b 05/24/17 1 Copyright 2017 Airmar Technology Corp. All rights
Mill Operator Users Guide. Mike Cope Product Technical Specialist
Mill Operator Users Guide Mike Cope Product Technical Specialist copem@hurco.com Table of Contents Performing a Tool Change Clear the Tool in Spindle Tool Touch-off Without touch probe With touch probe
Please read carefuly before using. Aerobic Lateral Trainer ASSEMBLY MANUAL H901
Please read carefuly before using. Aerobic Lateral Trainer ASSEMBLY MANUAL H901 TABLE OF CONTENTS 1 IMPORTANT SAFETY INFORMATION 2 Important Safety Precautions 2 Weight Limit Capacities 2 Warning 2 2
Image Smoothing. Controlling printed output. Printing. Using color. Paper handling. Maintenance. Troubleshooting. Administration.
Your printer driver provides you with the best quality output for various types of printing needs. However, you may want more control over how your printed document will look. 1 Your printer default is
Creating a Color Compensation file for Roche LightCycler 480 vers.i & vers. II
Creating a Color Compensation file for Roche LightCycler 480 vers.i & vers. II Due to ROX and Cy5 dye emmision spectra overlap Roche LightCycler 480 can pick up signals from a dye measured by another channel.
RQflex 2. Manual English
RQflex 2 Manual English Contents 1 Introduction 3 2 Description of the instrument 5 display, keys 6 technical data 8 3 Setting up the instrument 9 insertion of batteries 10 setting the time and date 11
Drawing Layouts Paper space & Model Space
Drawing Layouts Paper space & Model Space Users of Bricscad will have seen the tabs at the bottom left of the drawings area labelled: Model, Layout1, Layout2 but may not know how to use them or what they
1. Start with scatter plot: 2. Find corner points. 3. Capture image. 4. Corners
1. Start with scatter plot: 2. Find corner points Easiest way to insert picture properly in GeoGebra is to have corner points. We see that: bottom corner is (2,10) top corner is (9,21) 3. Capture image
RPS-9000 Programming Software for the TYT TH-9000
for the TYT TH-9000 Memory Types Memories Limit Memories VFO Channels Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS DCS Rx DCS Memory
Instruction Manual for the Software of ASSAN V2 Series Receiver
Instruction Manual for the Software of ASSAN V2 Series Receiver I. Setup 1. Double click SETUP to enter the welcome interface and click Next. 2. Enter your name and company name and click Next. 3. Select
Leica SPEII confocal microscope. Short Manual
Leica SPEII confocal microscope Short Manual Switching ON sequence: 1. Turn on the Workstation under the bench (top, far right). 2. Turn on the Supply Unit - Laser box (big green switch first and then
Channel Remote Programming: For the (35R Motor with or without a Plug) LEFT SIDE AND RIGHT SIDE MOTORS
2016 15 Channel Remote Programming: For the (35R Motor with or without a Plug) LEFT SIDE AND RIGHT SIDE MOTORS Right Side Worms FRONT REMOTE CONTROL BACK Left Side Worms Channel Display Up Stop Down Channel
Section 1 WHAT IS HAPPENING IN THE WIRES?
Section 1 WHAT IS HAPPENING IN THE WIRES? INTRODUCTION Electricity is usually invisible. Except for lightning and sparks, you never see it in daily life. However, light bulbs and a magnetic compass can
Color Insight: Color Optimization
Color Insight: Color Optimization Rev March 2016 Document Outline 1. Function of the optimization process 2. Color Insight terminology 3. Color matching preset creation 4. Optimization process overview
LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display.
LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. Four band MTR 4B shown Overview: The Mountain Topper Rigs are designed to be a very small,
Energate Foundation Meter Data Collector Installation Guide
Energate Foundation Meter Data Collector Installation Guide The Meter Data Collector works with Foundation s built-in Meter Data Receiver. The collector attaches to the meter provided by your electricity
Using Olympus dotslide for polarising microscopy
Using Olympus dotslide for polarising microscopy Background Because the dotslide system is built using a conventional microscope frame it lends itself to acquiring scans in different imaging modes whose
ATP-5189 Programming Software for the Anytone AT-5189
for the Anytone AT-5189 Memory Types Memories Limit Memories VFO Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS DCS Memory Channel
PANalytical X pert Pro High Resolution Specular and Rocking Curve Scans User Manual (Version: )
University of Minnesota College of Science and Engineering Characterization Facility PANalytical X pert Pro High Resolution Specular and Rocking Curve Scans User Manual (Version: 2012.10.17) The following
ScanGear CS-U 5.6. for CanoScan FB1210U Color Scanner. User s Guide
ScanGear CS-U 5.6 for CanoScan FB1210U Color Scanner User s Guide Copyright Notice Copyright 2000 Canon Inc. This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
MAXYM Mortiser Operating Manual
MAXYM Mortiser Operating Manual Rev 2.112/16/02 Copyright MAXYM Technologies Inc. Table of Contents Visual Tour 1-2 Operating the Maxym Mortiser 3 Starting the Mortiser 3 Touch Screen Description 3 Mortise
ATP-588 Programming Software for the Anytone AT-588
for the Anytone AT-588 Memory Channel Functions Memory Types Memories Limit Memories VFO Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS
RENISHAW INVIA RAMAN SPECTROMETER
STANDARD OPERATING PROCEDURE: RENISHAW INVIA RAMAN SPECTROMETER Purpose of this Instrument: The Renishaw invia Raman Spectrometer is an instrument used to analyze the Raman scattered light from samples
RA-1713G INTRODUCTION
INTRODUCTION The RA-1713G is an auxiliary electronics system for use with the Westrex RA- 1712G. It comprises a current regulated digital readout recorder lamp supply, a direct-photocell monitor amplifier
Horiba LabRAM ARAMIS Raman Spectrometer Revision /28/2016 Page 1 of 11. Horiba Jobin-Yvon LabRAM Aramis - Raman Spectrometer
Page 1 of 11 Horiba Jobin-Yvon LabRAM Aramis - Raman Spectrometer The Aramis Raman system is a software selectable multi-wavelength Raman system with mapping capabilities with a 400mm monochromator and
Impedance Transformation with Transmission Lines
Impedance Transformation with Transmission Lines Software Installation and Operation Manual Don Cochran WAØJOW 21826 Gardner Rd. Spring Hill, KS 66083 (913) 856-4075 Manual Revision 1 Page 1 Table of Contents
Measurement Method of High Absorbance (Low Transmittance) Samples by UH4150 INTRODUCTION
INTRODUCTION With UH4150, a detector can be selected depending on the analysis purpose. When analyzing a solid sample which doesn t contain any diffuse components, by selecting the direct light detector,
CAMM-1 GR Series VersaWorks Dual & PerfCutContour Workflow Guide
CAMM-1 GR Series VersaWorks Dual & PerfCutContour Workflow Guide October 25, 2017 Table of Contents Summary 1 Dual-Position Blade Holder 1 CutContour Optimal Blade Extension 2 PerfCutContour Optimal Blade
Assignment 5 due Monday, May 7
due Monday, May 7 Simulations and the Law of Large Numbers Overview In both parts of the assignment, you will be calculating a theoretical probability for a certain procedure. In other words, this uses
Contents STARTUP MICROSCOPE CONTROLS CAMERA CONTROLS SOFTWARE CONTROLS EXPOSURE AND CONTRAST MONOCHROME IMAGE HANDLING
Operations Guide Contents STARTUP MICROSCOPE CONTROLS CAMERA CONTROLS SOFTWARE CONTROLS EXPOSURE AND CONTRAST MONOCHROME IMAGE HANDLING Nikon Eclipse 90i Operations Guide STARTUP Startup Powering Up Fluorescence
BandMaster V Manual. Installation
BandMaster V Manual Installation Installing and configuring the BM-5 BandMaster V is a simple process. All the configuration process is done from the front panel. Installation and configuration steps are
reference guide reference guide reference guide
hp photosmart 240 series reference guide reference guide reference guide contents 1 welcome..................................... 1 find more information.............................. 1 what s in the box.................................
Moving money forward. CASSIDA TillTally + TillTally Elite Money Counting Scales
Moving money forward CASSIDA TillTally + TillTally Elite Money Counting Scales Table of contents: 1. INTRODUCTION 1.1 About the Cassida TillTally 2 1.2 Box contents 2 1.3 Front and rear views 3 1.4 Display
knitcompanion NextGen for ios Reference Guide
Contents Options... 2 Home Page... 3 Main Knitting Page Knit Mode... 7 Main Knitting Page Edit Mode... 12 Linked Counters... 16 PDF Viewer... 18 Magic Markers... 20 Setup Mode... 22 Smart Counters... 27
UV / VIS Spectrophotometer EMCLAB Instruments GmbH
A Professional Manufacturer UV / VIS Spectrophotometer EMCLAB Instruments GmbH EMCLAB Instruments GmbH Bismarckstrasse 120 47057 Duisburg Germany Phone: +49 203 3064042 Fax: +49 203 3064044 E-mail: info@emc-lab.de
FE-110/X-705 FE-100/X-710
DIGITAL CAMERA FE-110/X-705 FE-100/X-710 Advanced Manual Detailed explanations of all the functions for getting the most out of your camera. Basic Operation Shooting Playing Back Printing Online Pictures
How to remove Jammed Paper
How to remove Jammed Paper MC851(+)/MC860/MC861(+)/ ES8451MFP/ES8460MFP/ ES8461MFP Rev.1 Paper Jams Paper jams occasionally occur due to paper misfeeding from a paper tray or at any point on the paper
GENESYS 20 GENERAL PRACTICES AND INFORMATION
TECHNICAL MEMORANDUM NOTICE: This document is version controlled and was produced as a part of the GEX Information Program which requires that all Series 100 documents be reviewed periodically to maintain
For more information on these functions and others please refer to the PRONET-E User s Manual.
PRONET-E Quick Start Guide PRONET-E Quick Start Guide BASIC FUNCTIONS This guide will familiarize the user with the basic functions of the PRONET-E Servo Drive and assist with start up. The descriptions
User Operation of JEOL 1200 EX II
**Log onto Computer** Open item program Start Up Procedure User Operation of JEOL 1200 EX II 1. If scope is not running, locate an electron microscopy technician (EMT) to find out why not. 2. Turn up brightness
Quick Start MMRC Nicolet 6700 Revised 10/24/2018
Do Not Remove Quick Start MMRC Nicolet 6700 Revised 10/24/2018 1. Fill out the logbook before you begin. 2. Before you start the Nicolet should be on with purge gas flowing. 3. Check that the purge gas
Operating Checklist for using the Scanning Electron Microscope, JEOL JSM 6400.
Smith College August 2005 Operating Checklist for using the Scanning Electron Microscope, JEOL JSM 6400. CONTENT, page no. Pre-Check, 1 Specimen Insertion, 1 Startup, 2 Filament Saturation, 2 Beam Alignment,
Deceptive Jamming Using Amplitude-Modulated Signals
Exercise 3-1 Deceptive Jamming Using Amplitude-Modulated Signals EXERCISE OBJECTIVE To demonstrate the effect of AM noise and repeater inverse gain jamming, two angular deceptive EA used against sequential
TECHNICAL MEMORANDUM
TECHNICAL MEMORANDUM NOTICE: This document is version controlled and was produced as a part of the GEX Information Program which requires that all Series 100 documents be reviewed periodically to maintain
User s Guide. Slide Feeder for Flextight 949 and X5 Scanners English
User s Guide Slide Feeder for Flextight 949 and X5 Scanners English Table of contents Introduction 3 I m p o r t a n t Wa r n i n g s a n d R e s t r i c t i o n s 3 Sy s t e m R e q u i r e m e n t s
Thermo Scientific SPECTRONIC 200
molecular spectroscopy Thermo Scientific SPECTRONIC 200 Part of Thermo Fisher Scientific The New Standard for Routine Measurements Robust, Multifunction Sample Compartment Whether you measure in 10 mm
User manual AWR-8000 / AWR Advanced Wireless Communications
User manual AWR-8000 / AWR-8001 Advanced Wireless Communications THANK YOU! Thank you for your purchase of Advanced Wireless Communications AWR-8000 / AWR-8001 two-way radio. This portable two-way radio
ScanGear CS-U 6.0. for CanoScan D646U Color Scanner. User s Guide
ScanGear CS-U 6.0 for CanoScan D646U Color Scanner User s Guide Copyright Notice Copyright 2000 Canon Inc. This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
Basic Sewing Machine Parts/Their Purpose and Function
Basic Sewing Machine Parts/Their Purpose and Function Basic Sewing Machine Parts/Their Purpose and Function: 1) Bobbin Provides the bottom thread, the underside of the stitches a sewing machine forms.
Reference and User Manual May, 2015 revision - 3
Reference and User Manual May, 2015 revision - 3 Innovations Foresight 2015 - Powered by Alcor System 1 For any improvement and suggestions, please contact customerservice@innovationsforesight.com Some
Push-to-talk ios User Guide (v8.0)
Push-to-talk ios User Guide (v8.0) PTT 8.0 ios - Table of Contents 1 Activating PTT on your ios device... 4 How to activate PTT on your Android Smartphone... 4 How to Logout and Login to the PTT Service...
Conductivity +/ 2% 1 or 2 point remotely through PLC or directly on board. Any two lead Conductivity probe (K 0.01, K 0.1, K 1.
V 2.0 Revised 1/16/17 Conductivity IXIAN Transmitter Reads Range Accuracy Calibration Supported probes Temp probe Conductivity 0.07µS 100,000µS +/ 2% 1 or 2 point remotely through PLC or directly on board
Fire CR Calibration Guide
1 Fire CR Calibration Guide This reference guide will guide you through the steps to complete the calibration for the Fire CR.. Getting Started: 1. Click on the Opal Icon on the Desktop. Figure 1 2. Once