Light Control guide for Soundlight Comfort Ceiling OccuSwitch DALI Control Guide

Transcription

1 Light Control guide for Soundlight Comfort Ceiling OccuSwitch DALI Control Guide

2 Content: Ensure right physical install of all hardware / use remote control to commission the OccuSwitch Definitions of ceiling plan Calibrate light level Setting a mode Assign DALI function to every LED tile cluster Optional functions Set background level (optional, default 20%) Set power up state Set IR group to match system with remote control Movement test Back to basic setting Switch lights on/off!!! Attention Always keep pointed to OccuSwitch DALI sensor Attention Lights will allways flash once after every successful change Attention Luxmeter needed for calibration of the installation

3 1 Max 1 m Ensure right physical install of all hardware. See Installation Guide IG324 Definitions of ceiling plan Follow the lighting design for specified room type made by the lighting designer Examples: Group 2 x = Led Tile in assigned cluster o = Led Tile in assigned cluster LED Tile cluster = LED Tiles connected to same Control box Group = one or several LED Tile cluster having the same Dali assignment. E.g window or LED Tiles in cluster behaves equally

4 Calibrate the light level Luxmeter 3 1 Push Up or Down to set the required light level 2 Press Save when the lux meter is showing the required lux level (eg 500 lux)! Attention Always calibrate the installation Calibration must be done at night and office must be furnished Setting the modes 4 1 Press Select Press OK (4) (Check mode) m/s = master / slave t/w = task lighting / workspace lighting Mode Application 1 cell office m/s 2 open plan m/s 3 classroom m/s 4 open plan t/w 5 cell office t/w 6 7 toilets 8 meeting room 9 open plan t/w 10 custom More detailed information about Mode overview (default settings), see last page

5 DALI function assignment 5 1 Press Dali 2 Wait for a cluster of LED Tiles to flash If no flash occurs press 1 until a cluster of LED Tiles start flashing 3 Select function for cluster of LED Tiles: 1=window 2= 3=additional presence 4=additional absence 4 Repeat for next flashing cluster of LED Tiles (5 Press Dali to abort) When finished all luminaires flash once! Optional functions 6-11

6 Change Background level 6 1 Press % 2 Select 10%-70% 3 Press OK m/s = master / slave t/w = task lighting / workspace lighting Mode Application Background Factory default 1 cell m/s 2 open plan m/s 20% (all lights)* 3 classroom m/s 4 open plan t/w Preset 1** 5 cell t/w 6 20% (all lights)* 7 toilets Preset 1** 8 meeting room 9 open plan t/w 20% (all lights)* 10 custom Preset 1** * = default ** = workspace Change power-up state 7 1 Press power up 2 Select on/off status 3 Press OK Mode Power-up (factory default) 1 off 2 off 3 off 4 off 5 off 6 on 7 on 8 off 9 on 10 on

7 IR group addressing 1 Press IR group 8 2 Select group A-G 3 Press OK Set IR group remote control Movement test 9 1 Press test OccuSwitch DALI will now operate 10x faster than normal. MD timer = 30 sec fixed 2 Press test to stop (automatic stop after 60s no movement)

8 Back to basic setting (mode 1) 1 Press basic 10 2 Press OK Switch lights on or off 11 1 Press ON 2 Press OFF

9 Mode Application Occupancy 1 2 Cell office (default) Open plan office 3 Class room ManualON/ autooff Smart timer (minutes) Background period (minutes) Daylight override 10 0 N.a. 4 Open plan* Disabled 10 0 N.a. 5 Cell office* Disabled 10 0 N.a. 6 Corridor 7 Toilets 8 Meeting room ManualON/ autooff 9 Open plan office** Mode overview (default settings) (portal ) 10 0 Disabled 10 Infinite Daylight dependent regulation Daylight dependent switching Disabled Disabled Disabled 10 custom N.a. N.a. N.a. N.a. N.a. N.a. N.a. Parallel link period (Advanced ) N.a. N.a. Background lighting * Equals mode 1 and 2, but without MD active. Do not use these modes for normal applications. ** This mode works differently in the advanced (LRM2080) version. Here the lights will switch off (the basic never switches off) when none of the advanced OccuSwitch DALI units in the parallel network detect movement. If one, or more, do detect movement all other units will go to background level.