LightFlex Tunable-White LED nlight Programming Guide Programming Guide Overview
|
|
- Joanna Woods
- 5 years ago
- Views:
Transcription
1 LightFlex Tunable-White LED nlight Programming Guide Programming Guide Overview 1.1 nlight Hardware Components Available SensorView Settings, Factory Defaults Device Operation.... 6
2 1.1 nlight Hardware Components The LightFlex tunable-white LED is made up of the following nlight components see additional descriptions for each product below: OPTIONAL
3 nes ADCX LFT this is an open loop photosensor located in the LightFlex tube used to read sunlight. This photosensor broadcasts on two nlight photocell channels by default: Photocell Channel 1: Used for providing open loop intensity dimming control of the luminaire Photocell Channel 2: Used for providing open loop open/close control of the louver NOTE: If multiple LightFlex tubes are in the space, therefore multiple nes ADCX LFT devices, one photocell will operate as the master (i.e. the unit with the lowest nlight serial ID). For uniform control of all LightFlex tube louvers and luminaires, it is recommended to choose the nes ADCX LFT from the most centrally located LightFlex, and disable all other nes ADCX LFT from broadcasting. nsp5 2P LFT this is 2-pole relay device used to control the louver open/close based on nlight photosensor and (optionally) switch commands. Control of the louver is completed through line voltage control of the louver control motor. This louver control devices tracks the following channels by default: Switch Channel 3: This provides switch control of the louver with the npodm SW3 OCB by default, or other nlight switches if programmed accordingly Photocell Channel 2: Used for opening/closing the louver based on nes ADCX LFT reading Occupancy Channel 1: No occupancy sensors are provided by default, but introducing an occupancy sensor will provide open/close control nps 80 this is an nlight power supply used to provide bus power to all nlight devices listed here. nio EZDL CCT LFT this device provides a connection to the EldoLED driver to control the luminaire intensity and correlated color temperature (CCT). CAT5 3 total pre-terminated CAT5e cables are provided for connection between the following nlight devices: nes ADCX LFT and nsp5 2P LFT (length of cable provided will depend on tube length) nsp5 2P LFT and nps 80 nps 80 and nio EZDL CCT LFT CAT5 1FT Y J1 1 foot 1-male to 2-female CAT5 Y splitter. This would typically plug directly into the open port on the nio EZDL CCT LFT and allow for the LightFlex to be in the middle of the nlight daisychain Optional Items (sold separately): npodm SW3 OCB this is a standard nlight on/off WallPod with factory default programming to broadcast on switch channel 3 for plug-n-play control of the louver. Additionally, the factory pad printing reads OPEN and CLOSE to display to the user that this control is used for opening/closing the louver.
4 npodm 2P DX CCT this is a standard nlight wallpod used to control the LightFlex luminaire. Pole 1 of the switch, marked by ON/OFF and up/down arrows, broadcasts on switch channel 1 and is used to control luminaire LED intensity. Pole 2 of the switch, marked by CCT and up/down arrows, broadcasts on switch channel 2 and is used to control luminaire correlated color temperature (CCT) intensity. 1.2 Available SensorView Settings, Factory Defaults The following are default nlight broadcasting and tracking channels with the LightFlex solution, including optional npodm 2P DX CCT and npodm SW3 OCB:
5 The NEW settings that were introduced with the LightFlex solution, or changes to traditional default device settings, are the following: nes ADCX LFT: NOTE: Open loop photocell operation is shown graphically below Input High Trim (LED 100% Follow Photocell Level): Foot-candle level in the shaft in which the LEDs will begin dimming down from 100%. Default = 500FC Input Middle Trim (LED 50% Follow Photocell Level): Foot-candle level in the shaft in which the LEDs will be dimmed to 50%. Default = 1200FC Input Low Trim (LED 1% Follow Photocell Level): Foot-candle level in the shaft in which the LEDs will be full dim at 1%. Default = 2000FC Input Deadband Trim (LED Inhibit Offset): Offset (deadband) above Input Low Trim before Photocell Transition Off timer begins. Default = 50FC Morning Sun Inhibit (Louver Inhibit): Foot-candle level in shaft in which the Louver Transitions from Full Open to Full Close (Evening) or Full Close to Full Open (Morning) nsp5 2P LFT: Switch Tracking Channel: This is set to channel 3 by default, to track the npodm SW3 OCB. Photocell Tracking Channel: This is set to channel 2 by default, to track the second pole of the nes ADCX LFT. nio EZDL CCT LFT: Follow Photocell Mode: This is typically disabled by default, but in order to respond to the photosensor, this is now set to Enabled Both Positive and Negative by default. WallPod Dimming Adjustments: This is typically set to Permanent by default, but for the LightFlex solution it is set to Temporary Override. Under Temporary Override, any dimming wallpod command will temporary disable the LEDs from following the photosensor dimming commands until the lights are cycled by switch or occupancy sensor (upon which they will return to following the photosensor). Color Temperature Percent: The default color temperature is set to 25%, which is ~3600K npodm SW3 OCB: Switch Broadcasting Channel: This is set to channel 3 by default, to control the nsp5 2P LVR by default. npodm 2P DX CCT: The default settings on this device match that of a typical npodm 2P DX.
6 1.3 Device Operation The intended out-of-box operation of the LightFlex tunable white LED is the following: NOTES: If multiple LightFlex tubes are in the space, therefore multiple nes ADCX LFT devices, one photocell will operate as the master (i.e. the unit with the lowest nlight serial ID). For uniform control of all LightFlex tube louvers and luminaires, it is recommended to choose the nes ADCX LFT from the most centrally located LightFlex, and disable all other nes ADCX LFT from broadcasting. If individual photocell control of each LightFlex is desired, there is a limit to eight (8) LightFlex tubes in the same nlight daisy-chain. Each LightFlex photosensor broadcasts on two photocell channels, and there are 16 available photocell channels on a local nlight zone. All values shown below in bold are configurable settings. Morning Sequence: o Photosensor Reads 50 FC louver opens, allowing light into the space o Photosensor Reads 500 FC LEDs begin dimming o Photosensor Reads 1200 FC LEDs dimmed to 50% Mid-Day Sequence: o Photosensor Reads 2000 FC LEDs dimmed to 1% o Photosensor Reads 2050 FC (Low Setpoint + Dead-band) LEDs turn off Afternoon Sequence: o Photosensor Reads 2000 FC LEDs turn on to 1% o Photosensor Reads 1200 FC LEDs dimmed to 50% o Photosensor Reads 500 FC LEDs at full bright, 100% o Photosensor Reads 50 FC louver closes, preventing electric light from escaping the space
LIGHTFLEX LED (SLFTL) tunable-white LED
SPECIFICATIONS LightFlex LED Type: SLFTL Tubular Daylighting System SLFTLfeaturing Tunable White LEDs Project: OVERVIEW LightFlex LED is the industry s first commercial daylighting system with integrated
More informationFeatures Grayscale and Color Accent. Full control over Grayscale speed on second pole. Full control over Color Accent color on second pole
ntune Rubik Grayscale & Color Accent User Programming Guide The ntune programming guide provides an overview of the Grayscale and Color Accent Mainstream Dynamic Features application in SensorView with
More informationCatalog Number. Notes
Catalog Number FETURES & SPECIFICTIONS INTENDED USE The LT est-in-value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationCatalog Number. Notes
Catalog Number FETURES & SPECIFICTIONS INTENDED USE The LT est-in-value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationGR i. design guide. Control Panel. MicroPanel-iDH and -idim. Switches. Photosensor. The MicroPanel-iDH or -idim. Accessories
The Micro Panel -idim and -idh have been specifically designed for daylight harvesting situations. This design guide is to help in the layout of such systems to achieve the proper balance of electric lighting
More informationSingle-zone Daylighting Control Sequences of Operation. Topic: DLM Operation with LMLS-400 Photosensor, v2.xx Issue: # TB185 Date: March 10, 2012
Understanding the capabilities of Digital Lighting Management (DLM) photosensors, and how to configure the sensors for the desired control strategy is one key to successful daylighting controls projects.
More informationThis document is intended for Lighting Control Systems professionals
This document is intended for Lighting Control Systems professionals This document applies to fixture with factory installed SVPD1, SVPD2, SVPD3 integrated sensors. Table of contents Quick Reference Guide...
More informationCatalog Number. Notes
Catalog Number Notes FETURES & SPECIFICTIONS INTENDED USE The LT est-in-value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationCatalog Number. Notes
Catalog Number Notes FETURES & SPECIFICTIONS INTENDED USE The LT est-in-value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationCatalog Number. Notes
Catalog Number Notes FETURES & SPECIFICTIONS INTENDED USE The LT est-in-value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationSlot PSW LED. Beauty Performance Control
Slot PSW LED Beauty Performance Control Lens Options Asymmetric Edge View Louver Batwing/Lambertian Wall Graze Wall Wash Lambertian Exceptional Performance The Slot PSW LED is available in 2 and 4" apertures,
More informationUser manual. KNX MultiController DALI. Article number: 5410x / 5411x. function Technology AS
User manual KNX MultiController DALI Article number: 5410x / 5411x Picture: KNX MultiController DALI with Reed panel and sensor function Technology AS Table of contents 1 KNX MULTICONTROLLER... 3 2 INTRODUCTION...
More informationGRX-DACPI Automatic Daylighting Control
Automatic Daylighting Control Description Saves energy in spaces with windows, skylights, or doors. Automatically dims lights when the sun is bright. Monitors ambient daylight via Lutron s MW-PS-WH photosensor
More informationOCCUPANCY SENSOR REMOTE USER GUIDE
OCCUPANCY SENSOR REMOTE USER GUIDE Use the handheld programming remote to test and adjust the settings of your occupancy sensor, which can accommodate up to six sensor parameter profiles. FSP-2X1 is the
More informationUser Manual. KNX MultiLight Dali. Article number: function Technology AS. Picture: KNX MultiLight products
User Manual KNX MultiLight Dali Article number: 44002 Picture: KNX MultiLight products function Technology AS Table of Contents 1 THE KNX MULTILIGHT DALI... 3 2 INTRODUCTION... 3 3 START-UP AND GENERAL
More informationModbus communication module for TCX2: AEX-MOD
Modbus communication module for TCX2: Communication Specification TCX2 is factory installed in TCX2 series controllers with -MOD suffix, and is also available separately upon request for customer installation
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
FSP-2X1 Digital High/Low Pir Fixture Integrated Sensor INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
More informationInstalling the FSP-211 Sensor in Light Fixture
(grey) WATTSTOPPER VOLTAGE HIGH/LOW/OFF PIR FIXTURE INTEGRATED OUTDOOR PHOTO/MOTION SENSOR Product Overview The is a passive infrared (PIR) outdoor sensor that raises or lowers the electric lighting level
More informationTEC Controller Constant Volume with Hot Water Reheat, Application Application Note Building Technologies
TEC Controller Constant Volume with Hot Water Reheat, Application 2033 Application Note 140-1023 Building Technologies Table of Contents Overview... 4 Hardware Inputs... 5 Hardware Outputs... 5 Secure
More informationFIXTURE INTEGRATED DAYLIGHT DIMMING PHOTOSENSOR
FIXTURE INTEGRATED DAYLIGHT DIMMING PHOTOSENSOR Product Overview The is a fixture-integrated dimming photosensor. It provides a continuous dimming signal to a 0-10 VDC dimming ballast, based on daylight
More informationSRC-110 Series Zone Controllers with Modbus RTU
Product sheet CT2.142 Type SRC-110-MOD SRC-110 Series Zone Controllers with Modbus RTU The SRC-110 series controllers have been designed for zone heating and cooling control. The controllers have 3 analogue
More informationPhilips Ledalite Phone: Fax: Web: Programming Guide Version 2.0
Philips Ledalite Phone: 604.888.6811 Fax: 800.665.5223 Web: www.ledalite.com Programming Guide Version 2.0 AIRWAVE PROGRAMMING GUIDE 1.0 Linking/Unlinking an Airwave Switch or Photosensor to a Transceiver
More informationHigh/Low Bay Passive Infrared Occupancy Sensor
Models Sensors: HBP-111-L7, with IR remote capability HBP-112-L7, no IR capability High/Low Bay Passive Infrared Occupancy Sensor Mounting Modules: HBP-EM1 extender module HBP-SM1 surface mount module
More informationLC8 & LC8-15. Single Level Lighting Controller INSTALLATION AND MAINTENANCE MANUAL (IMM) 205_LC8_R4
Single Level Lighting Controller INSTALLATION AND MAINTENANCE MANUAL (IMM) 205_LC8_R4 TABLE of CONTENTS 1 INTRODUCTON...3 1.1 GENERAL...3 1.2 OVERVIEW...3 2 INSTALLATION...4 2.1 POWER CONNECTIONS...4 2.2
More information800 TO 5500 LUMEN 8 LED CYLINDER HYPERBOLIC / PARABOLIC / WALLWASH / OPEN APERTURE LC8 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from to over Efficacies up to lm/w Superior-quality white LED light output using Chip on Board technology
More informationEVDP610 IXDP610 Digital PWM Controller IC Evaluation Board
IXDP610 Digital PWM Controller IC Evaluation Board General Description The IXDP610 Digital Pulse Width Modulator (DPWM) is a programmable CMOS LSI device, which accepts digital pulse width data from a
More informationBruno LED Design2Ship
SPECIFICATIONS HIGHLIGHTS Design2Ship DIMENSIONS BRM9L 1 3 4 Maximum order qty of 500 linear feet 5 business days from clean release of the order Total System Integration features 5-year limited warranty
More information800 TO 5500 LUMEN 6 LED CYLINDER HYPERBOLIC / PARABOLIC / WALLWASH / OPEN APERTURE LC6 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from to over Efficacies up to lm/w Superior-quality white LED light output using Chip on Board technology
More informationManual and application description
Manual and application description Audio-Actuator AM 840 1. Device description 1.1 General This device was developed according to the rules of the EIBA and EIBA certified. Condition for working with this
More informationRelay Driver Overview and Applications
Relay Driver Overview and Applications Describes Basic and Advanced Settings for common and alternative/novel uses for the Relay driver (RD-1). Morningstar s Relay Driver (RD-1) is a fully programmable
More informationActuating Terminal Equipment Controller (ATEC) Base VAV - Cooling or Heating, Application Application Note
Actuating Terminal Equipment Controller (ATEC) Base VAV - Cooling or Heating, Application 2521 Application Note 140-1218 Building Technologies Table of Contents Overview... 4 Hardware Inputs... 5 Hardware
More informationAL-DALI-010v 0-10v Dimmer 3-Way switch with DALI
ATX LED Consultants Inc 815-A Brazos #326 Austin Tx, 78701 512 377 6052 http://atx-led.com AL-DALI-010v 0-10v Dimmer 3-Way switch with DALI Product Description - AL-DALI wall switch with 0-10v output Combine
More information800 TO 2800 LUMEN 4 LED CYLINDER HYPERBOLIC / PARABOLIC / WALLWASH / OPEN APERTURE LC4 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from to over Efficacies up to lm/w Superior-quality white LED light output using Chip on Board technology
More informationHIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE FOR FLEXIBLE MOUNTING
HIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE FOR FLEXIBLE MOUNTING Product Overview The FSP-2x1B is a family of passive infrared (PIR) outdoor sensors that raise or lower the electric
More information800 TO 5500 LUMEN 6 LED CYLINDER HYPERBOLIC / PARABOLIC / WALLWASH / OPEN APERTURE LC6 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from to over Efficacies up to lm/w Superior-quality white LED light output using Chip on Board technology
More informationAL-DALI-010v 0-10v Dimmer 3-Way switch with DALI
ATX LED Consultants Inc 815-A Brazos #326 Austin Tx, 78701 512 377 6052 http://atx-led.com AL-DALI-010v 0-10v Dimmer 3-Way switch with DALI Product Description - AL-DALI wall switch with 0-10v output Combine
More informationSentido KNX Manual. Sentido KNX. Manual. basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium
basalte bvba hundelgemsesteenweg a 980 merelbeke belgium / 68 06 basalte Table of contents:. Introduction... 3. Installation... 4. 3. Identifying the parts... 5 General... 6 3. General functions... 7 3.
More informationUniversal Controller
Universal Controller Overview and Configuration Manual Overview... 1 About this Manual... 1 Introduction... 5 Hardware Overview... 5 Software Overview... 7 Interpreting Flow Diagrams... 8 Foreign Language
More informationHIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE WITH BLUETOOTH
HIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE WITH BLUETOOTH Product Overview The FSP-3x1B is a family of passive infrared (PIR) outdoor sensors that raise or lower the electric lighting
More informationJaguar Motor Controller (Stellaris Brushed DC Motor Control Module with CAN)
Jaguar Motor Controller (Stellaris Brushed DC Motor Control Module with CAN) 217-3367 Ordering Information Product Number Description 217-3367 Stellaris Brushed DC Motor Control Module with CAN (217-3367)
More informationHuman Centric Lighting System
Human Centric Lighting System PIR HHC24 HHC23 HHC245 Circadian Rhythm sensor with Tunable white LED driver Lighting can reduce energy bills, it also can boost productivity and promote the wellbeing of
More informationUSER MANUAL. EPP Intelligent Positioner Control Unit 1/22.
USER MANUAL - Intelligent Positioner Control Unit 1/22 Table of contents: 1 General... 3 1.1 Safety instructions... 3 2 Application... 4 3 Electrical specifications and terminals... 5 3.1 Control loop...
More informationluxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationCost Effective Simplified Controls for Daylight Harvesting
Cost Effective Simplified Controls for Daylight Harvesting Konstantinos Papamichael, Erik Page, and Keith Graeber California Lighting Technology Center, University of California, Davis ABSTRACT Most commercial
More informationDLC-PDC PHOTODIODE CONTROLLER
DLC-PDC PHOTODIODE CONTROLLER INSTALLATION AND OPERATION INSTRUCTIONS 203 Cooper Circle, Peachtree City, GA 30269 Customer Service: Telephone: (800) 553-3879 Fax: (800) 954-7016 DLC-PDC Rev. 2 TABLE of
More information815LT Submersible Smart Level Transmitter
These instructions provide information for installation, process connection, electrical connection, configuration, operation and maintenance of the 815LT Submersible Smart Level Transmitter. The 815LT
More informationcontrol & display PROGRAMMABLE SENSOR CONTROLLER COMPLETE VERSATILITY OF SENSOR MANAGEMENT & DATA COMMUNICATIONS
S E N S O R S PROGRAMMABLE SENSOR CONTROLLER TX9044 COMPLETE VERSATILITY OF SENSOR MANAGEMENT & DATA COMMUNICATIONS Analogue sensors, temperature devices, frequency inputs and digital sensors direct fingertip
More informationWhite Paper - Photosensors
Page 1 of 13 Photosensors: Technology and Major Trends by Craig DiLouie, Lighting Controls Association Posted December 2009 Special thanks to the following Lighting Controls Association member representatives
More informationFixture Built-in Sensor Daylight Harvest Version
Fixture Built-in Sensor Daylight Harvest Version Model: HC419VRC /DH Infrared remote receiver Detection area Hold-time Daylight sensor Buzzer Sensor antenna Photocell Installation hole (4.2mm) 4.2 45 Stand-by
More informationBrushed DC Motor Control. Module with CAN (MDL-BDC24)
Stellaris Brushed DC Motor Control Module with CAN (MDL-BDC24) Ordering Information Product No. MDL-BDC24 RDK-BDC24 Description Stellaris Brushed DC Motor Control Module with CAN (MDL-BDC24) for Single-Unit
More informationMARK ARCHITECTURAL LIGHTING TM. Slot 2 LED Direct Pendant. Technical Drawing. Specification Features. Fixture Performance
The Slot LED family of luminaires offers an unparalleled package of performance and features for your next lighting project. Precision lumen DIRECTIR optics deliver optimized light where needed for ceilings
More informationLight Control guide for Soundlight Comfort Ceiling OccuSwitch DALI Control Guide
Light Control guide for Soundlight Comfort Ceiling OccuSwitch DALI 2013.09 Control Guide Content: 1 2 3 4 5 6 7 8 9 10 11 Ensure right physical install of all hardware / use remote control to commission
More informationFSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR
FSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR CAUTIONS INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including
More informationSlot 4 LED Direct Pendant MARK ARCHITECTURAL LIGHTING TM. Technical Drawing. Specification Features. Fixture Performance
The Slot LED family of luminaires offers an unparalleled package of performance and features for your next lighting project. Precision lumen DIRECTIR optics deliver optimized light where needed for ceilings
More informationBlue Point Engineering
DMX Data Analyzer Board nstruction Overview DMX Analyzer - Tester PC Board Design your own enclosure with an analyzer / tester display or add to your existing equipment or system. The DMX Analyzer is a
More information2 Pendant Adjustment. Pendant Slider Plate. 3/4 (19mm) IP, (29mm) O.D. Knockouts. 1/2 (13mm) IP, (22mm) O.D. Knockout
CXB Series LED Luaire Universal Hook and Cord, and Optional Junction box or Pendant Mount with Sensor IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed
More informationChanging settings in the BlueSolar MPPT Charge Controllers
2016-11-21 07:40 1/14 Changing settings in the BlueSolar MPPT Charge Controllers Changing settings in the BlueSolar MPPT Charge Controllers DEPRECATED: Use VictronConnect instead of mpptprefs We recommend
More informationNRT 105: Electronic fan-coil controller, equiflex
Product data sheet 4.04 R 105: Electronic fan-coil controller, equiflex How energy efficiency is improved ECO Meter for displaying the current energy consumption and digital input for the change-over between
More informationApplications. HBT02 Transceiver Node. Features. Note: This datasheet is intended for information related to the hardware only.
Synchrony ighting Control With Wireless Technology HBT01 / HBT02 with HC038V / HCD038 Built-in Detachable Version Applications The freedom of wireless mesh networks configured by smartphone APP s considerably
More informationE-BUS Digital Room Sensor Technical Guide
E-BUS Digital Room Sensor Technical Guide TABLE OF CONTENTS OVERVIEW... 3 BASIC OPERATION... 4 Sensor Operation... 4 LED Operation... 4 MOUNTING AND WIRING... 5 Dimensions... 5 Environmental Requirements...
More informationDALI slave, one to four channels PWM and I2C output
DALI slave, one to four channels PWM and I2C output 1. Features DALI to PWM and I2C controller Pin selectable 1 to 4 channels Access to raw arc power values via I2C Access to mapped brightness values via
More informationSeries 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual
THE HIGH PERFORMANCE COMPANY Series 70 Hold 1 sec. Hold 1 sec. FOR MORE INFORMATION ON THIS PRODUCT AND OTHER BRAY PRODUCTS PLEASE VISIT OUR WEBSITE www.bray.com Table of Contents 1. Definition of Terms.........................................2
More informationCXB Series SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. LED Luminaire TO INSTALL: INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION
CXB Series LED Luaire Junction Box, Pendant and Hook and Cord IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND
More informationSELECTABLE MODE HIGH/LOW/OFF PIR FIXTURE INTEGRATED INDOOR/OUTDOOR MOTION/PHOTO SENSOR
SELECTABLE MODE HIGH/LOW/OFF PIR FIXTURE INTEGRATED INDOOR/OUTDOOR MOTION/PHOTO SENSOR FSP-22 FSP-212 * Models FSP-22, 12-32VDC Use with dim-to-off driver or ballast or with Wattstopper power pack FSP-212,
More informationGUIDE SPECIFICATIONS CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP GENERAL DESCRIPTION
GUIDE SPECIFICATIONS 256920-UGS-A-0506 Simplicity Intelli-Comfort Optional Control in 3-25 Ton Packaged Units GENERAL DESCRIPTION CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP Equipment with Simplicity
More informationTECO F510 Inverter. Quick Start Guide. Step 1. Supply & Motor connection
Quick Start Guide TECO F510 Inverter This guide is to assist you in installing and running the inverter and verify that it is functioning correctly for it s main and basic features. For detailed information
More informationDESCRIPTION & OPERATION: PIR OCCUPANCY SENSOR MSWSFSP221B-D FEATURES:
PROJECT NAME: CATALOG NUMBER: NOTES: FIXTURE SCHEDULE: Page: 1 of 5 PIR OCCUPANCY SENSOR DESCRIPTION & OPERATION: These fixture mounted sensors provide multi-level control based on motion and/or daylight
More informationRAM 712 KNX room thermostat for surface-mounted and flush-mounted installation
RAM 712 KNX room thermostat for surface-mounted and flush-mounted installation RAM 712 712 9 200 Version: Dec-10 (subject to change) Page 1 of 65 Contents 1 Functional characteristics... 4 1.1 Operation...
More informationLITECOM. Special luminaires SEQUENCE infinity
LITECOM Special luminaires SEQUENCE infinity Legal information Copyright Copyright Zumtobel Lighting GmbH All rights reserved. Manufacturer Zumtobel Lighting GmbH Schweizerstrasse 30 6850 Dornbirn AUSTRIA
More informationServo 8 Torque Board Doc V 1.2
Features: Servo 8 Torque Board Doc V 1.2 RS-232 hobby servo controller with torque feedback No servo modifications required Eight independent 8-bit servo control outputs allow 254 positions for each servo.
More informationmaxon document number:
maxon document number: 791272-04 1 Table of contents... 2 2 Table of figures... 3 3 Introduction... 4 4 How to use this guide... 4 5 Safety Instructions... 5 6 Performance Data... 6 6.1 Motor data... 6
More informationapplication software
application software A faire Input module - ON/OFF outputs and blind shutter Electrical/Mechanical characteristics: See product user manual Product reference Product designation Application software ref
More informationCHAPTER AC DRIVE PARAMETERS. In This Chapter...
CHAPTER AC DRIVE 4 PARAMETERS In This Chapter... GS2 Parameter Summary....................4 2 Detailed Parameter Listings.................4 11 Motor Parameters........................4 11 Ramp Parameters.........................4
More informationRadio Window Sensor and Temperature Sensor Programming in HomeWorks QS
Radio Window Sensor and Temperature Sensor Programming in HomeWorks QS Table of Contents 1. Overview... 2 2. General Operation... 2 2.1. Radio Window Sensor Communication... 2 2.2. Temperature Sensor Communication...
More informationEmergency PHM Series. Emergency PowerHUBB Node - Master/Control/Tunable White. Dimensional Data. Ordering Information (Example: PHM4PC EM)
Emergency PHM Series Emergency PowerHUBB Node - Master/Control/Tunable White Project Name NETWORK Catalog No. Date Product Features The Hubbell Control Solutions' (HCS) PowerHUBB node provides power distribution
More informationD824-LED D Low Profile Gladetino Luminaire. 10 Yr USA. Performance Data
84-LE Low Profile Gladetino Luminaire Performance ata CRI 70+, 9 Optional CCT 3000K, 300K, 4000K, 000K, Amber Projected Lifetime 86,000 ours (L70) 8,000 ours (L80) imming 0-0V imming Standard, 0% to 00%
More informationLighting Depth: Physical Therapy Suite Franklin Care Center, Franklin Lakes, NJ
Physical Therapy Suite Overview: The physical therapy suite will be used by the patients for physical rehabilitation. It is similar to a small gym with exercise mats, bikes, a treadmill, stairs, parallel
More information1. Use of the application program
s GAMMA instabus 12 A1S2 Blind, 2 inputs 207301 1. Use of the application program 2. Product description 2.1. Description of the blind actuator UP 520/31 2.2. Delivered with the blind actuator UP 520/31
More informationFor Direct computer control see the Data Out connector description. For Radio control see the Data In connector description.
Transceiver interface Operation for Steppir For Direct computer control see the Data Out connector description. For Radio control see the Data In connector description. The following radios are supported:
More informationLIGHTING Common terminology 2. Sources and luminaires 3. Controls
LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in
More informationEQ-ROBO Programming : bomb Remover Robot
EQ-ROBO Programming : bomb Remover Robot Program begin Input port setting Output port setting LOOP starting point (Repeat the command) Condition 1 Key of remote controller : LEFT UP Robot go forwards after
More informationADVANCED PLC PROGRAMMING. Q. Explain the ONE SHOT (ONS) function with an application.
Q. Explain the ONE SHOT (ONS) function with an application. One of the important functions provided by PLC is the ability to program an internal relay so that its contacts are activated for just one cycle,
More informationSPTO 1D2. Control module SPAC 3 C. User s manual and Technical description. U aux V _ V _. f n SPTO 1D2. I n = 1 / 5 A( I o)
SPTO 1D2 Control module User s manual and Technical description f n = 50 60 Hz I n = 1 / 5 A ( I ) I n = 1 / 5 A( I o) SPAC 3 C 2 5 IRF O I TEST INTERLOCK GAS PRESSURE MOTOR VOLTAGE STEP R L U aux 80...
More informationCrestron CLS-C6 Series ilux Integrated Lighting System User Guide
. Crestron CLS-C6 Series ilux Integrated Lighting System User Guide Contents ilux Integrated Lighting System: CLS-C6 Series 1 Introduction...1 Operating Modes...5 Standard Mode...5 Lights Mode...5 Shades
More informationTEAM DIGITAL. SC82 Servo Controller
TEAM DIGITAL SC Servo Controller Improving the world of DCC > DCC compatible accessory decoder > Control servos motors > Output status LEDs > inputs for turnout control > 6 inputs for semaphore signaling
More informationTimeless looks, smart optics. Linear. Sona
Linear Sona Suspended & wall Timeless looks, smart optics Incredible efficacy & boundless lighting choices mean the re-engineered Sona LED linear is destined to become a future classic. Sona suspended
More informationLIGHTING Common terminology 2. Sources and luminaires 3. Controls
LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in
More informationLP B C D E F G H I MOUNTING FINISH
84-LE Low Profile Gladetino Luminaire Client: Project Name: Order #: Type: Qty: Performance ata CRI 70+, 9 Optional CCT 3000K, 300K, 4000K, 000K, Amber Projected Lifetime 86,000 ours (L70) 8,000 ours (L80)
More informationGeneral Description. The TETRIX MAX Servo Motor Expansion Controller features the following:
General Description The TETRIX MAX Servo Motor Expansion Controller is a servo motor expansion peripheral designed to allow the addition of multiple servo motors to the PRIZM Robotics Controller. The device
More informationWall Mounted E-BUS CO 2. Sensor Technical Guide
Wall Mounted E-BUS CO 2 Sensor TABLE OF CONTENTS OVERVIEW... 3 Features... 3 Environmental Requirements... 3 WALL MOUNTED E-BUS CO 2 WIRING TO DDC CONTROLLER... 4 TROUBLESHOOTING... 5 Setting The Sensor
More informationKNX manual 1-channel flush-mounted switch actuator SU 1
KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product
More informationLOAD AWG Solid CU Wire Only LINE NEUT FSP-211. High/Low PIR Occupancy Sensor 230 VAC, 50 Hz 1200W max ballast 5E4
DESCRIPTION AND OPERATION The is a motion sensor that dims lighting from high to low based on movement. This slim, low-profile sensor is designed for installation inside the bottom of a light fixture body.
More informationHigh Current DC Motor Driver Manual
High Current DC Motor Driver Manual 1.0 INTRODUCTION AND OVERVIEW This driver is one of the latest smart series motor drivers designed to drive medium to high power brushed DC motor with current capacity
More informationHome Automation, Inc. Omnistat2. RC-1000 and RC-2000 Communicating Thermostat. Serial Protocol Description
Home Automation, Inc. Omnistat2 RC-1000 and RC-2000 Communicating Thermostat Serial Protocol Description This document contains the intellectual property of Home Automation, Inc. (HAI). HAI authorizes
More informationXIM Gen4 Sensor Programming Examples. Rev /05/2016
XIM Gen Sensor Programming Examples Rev 0.6 2/0/206 Overview The latest XIM Gen firmware (V0.28), Xsensor firmware (V0.0) and XIM-BLE Control Panel (V..) update includes significant changes to sensor support.
More informationIndustrial Lighting Products
Project Name: Catalog Number: Volts/Watts: Fixture Type: Lamps/Board: Commercial HIGH BAY - 100W LED FEATURES Aluminum Body Tool-Less Hinged Bottom Ballast Access Door Frosted or Polycarbonate Lens Options
More informationBENCHMARK LIGHTING: COST SAVING TECHNOLOGIES
BENCHMARK LIGHTING: COST SAVING TECHNOLOGIES TECHNOLOGY UPGRADES ALVIN WAI, E.I.T. BC Hydro Power Smart Engineering Twitter hashtag: #ps10 DYNAMIC/CONTROLLED LIGHTING Saves money Energy costs Maintenance
More informationCineMoco v2.0. anual
CineMoco v2.0 anual Table of Contents 1 Introduction 2 Hardware 3 User Interface 4 Menu Status Bar General (GEN) Controller (CON) Motor (MTR) Camera (CAM) 5 Recording Modes 6 Setup Styles 7 Move Types
More informationBeveLED 2.2 Infinite Color+ - B4RC-FC1 4.5 Round Deep Regress Downlight
Field Convertible from Trimless or Millwork to Trimmed Trimmed - B4RCF-FC1 Trimless - B4RCL-FC1 usailighting.com/infinitecolor Millwork - B4RCM-FC1 BeveLED 2.2 Infinite Color+ - Access to a wide variety
More informationTable of Contents Thank You... 5 What is the Liquid Router?... 5 Operating Guidelines... 6
Table of Contents Thank You... 5 What is the Liquid Router?... 5 Operating Guidelines... 6 Powering the unit... 6 Which MIDI Cables Should Be Used... 6 Care and Cleaning... 7 Installing Expansion Devices...
More information