Operating instructions II / 2004
|
|
- Mariah Hopkins
- 6 years ago
- Views:
Transcription
1 Operating instructions II / 2004 Light and presence sensor TOUCH DIM LS/PD LI OSRAM GmbH Costumer-Service-Center (CSC) Steinerne Furt Augsburg, Germany Tel. : (+49) 1803 / (charges apply) Fax.: (+49) 1803 /
2 General Contents General Installation Operation Appendix Application and function...2 Design and dimensions...3 Wiring diagram...3 Installation hints...4 General functions...5 Controlling brightness at the workplace...5 Troubleshooting...7 Technical data...8 Application and function The TOUCH DIM LS/PD LI sensor was developed to regulate and control the brightness at workplaces. The sensor measures the brightness and detects the presence of persons. The lighting conditions at the workplace are maintained at a user-adjustable set point by providing artificial light according to the amount of available daylight. If there is more than sufficient daylight, the connected luminaries are switched off. The TOUCH DIM sensor can be installed in luminaires (e.g. floor-standing luminaires), or by use of a flush device box with adequate cover also into the ceiling. Good workplace lighting makes the working environment more comfortable. Energy savings of up to 70% can be made compared with conventional workplace lighting. Safety and installation information The unit should be installed and tested only by a qualified electrician. Power to the units must be switched off before any work is undertaken. The relevant safety and accident prevention regulations must be observed. The TOUCH DIM sensor is used exclusively for controlling electronic control gear type QUICKTRONIC INTELLIGENT LI (QTi LI...DIM) or HALOTRONIC INTELLIGENT LI (HTi LI..DIM). No further control units may be operated on the control line. Other applications are not permitted. They may destroy the TOUCH DIM LS/PD LI and other equipment. The maximal number of ECG and the maximal overall cable length between push button, sensor and ECG has to be respected (see Technical data). If the control cable is wired with external voltage, the unit may be destroyed. The TOUCH DIM Sensor may only be supplied with AC operating voltage. This is particularly important to remember if UPS systems are used. page 2 OSRAM - operating instructions TOUCH DIM LS/PD LI
3 Installation Design and dimensions Wiring diagram L N PE Push button (manual control) L N S TOUCH DIM Sensor signal wire length max. 10m ECG QTi LI ECG QTi LI ECG QTi LI Lamp Lamp Lamp max. 4 QTi ECG or HTi transform ers Push button and sensor have to be connected to the same mains phase! ECG QTi LI Lamp OSRAM - operating instructions TOUCH DIM LS/PD LI page 3
4 Installation Installation hints The sensor is connected to a 3 wire cable which is admitted for mains voltage. Parallel connection of several sensors is not allowed. The sensor is typically installed in luminaires, ceiling installation is possible by use of a flush device box and an adequate cover. A sensor has a detection angle of approx If it is installed at a height of 3 m, it can mo nitor an area with a maximum diameter of 5-7 m. When installing the sensor, please note the following: The entire workplace must lie within the monitoring cone of the sensor. Avoid placing the sensor where it is directly exposed to light from other sources as this will lead to incorrect measurements. The sensor should be installed centrally in the sphere of action, so that all controlled lumnaires contribute with the same proportion to the measured brightness. The sensor must not be exposed to drafts (e.g. near air vents). A draft could be misinterpreted as the presence of a person in the room. Example: Office with 4 controlled luminaires: window controlled luminaire controlled luminaire possible place of installation window controlled luminaire controlled luminaire optimal place of installation Touch DIM Sensor 2m window min. 40 1m Height above window sill 0m 1m min. distance to window 2m 0m Diagram: minimal distance to windows page 4 OSRAM - operating instructions TOUCH DIM LS/PD LI
5 Operation General functions Switching the luminaire on/off 1. Briefly press the switch once. The luminaire is switched on or off each time the switch is operated. Changing the brightness With the luminaire switched off: 1. Press the switch. Keep pressing the switch until the required brightness is reached. With the luminaire switched on: 1. Press the switch. Keep pressing the switch until the required brightness is reached. The luminaire goes on at minimum brightness. The longer the switch is pressed, the brighter the luminaire gets. When the switch is released the luminaire will remain at the brightness it has reached. The brightness will change. When the switch is released the luminaire will remain at the brightness it has reached. Switching between more and less brightness: 2. Release the switch then press it again. Keep pressing the switch until the required brightness is reached. Every time the switch is held down the unit toggles between more light and less light. Note: Changing the brightness deactivates brightness control. When the unit is switched on again brightness control is reactivated, if a set point value was is stored. Controlling brightness at the workplace Switching the luminaire on and off automatically If the motion detector does not detect movement for 15 minutes, the lighting control unit will reduce the brightness level to the minimum value and then switch off the luminaire. As soon as motion is detected the luminaire will be switched on again, provided that artificial light is needed. If natural daylight is more than max. range of operation, the lighting control unit will switch off the luminaire. To avoid unnecessary and disturbing switching of the lamps, the light is switched off with a delay of approx. 15 minutes. If the brightness at the workplace gets less and persons are present, the lighting control unit will switch on the luminaire again and control the brightness. Adjustment / Storage of the set point for brightness control 1. Change the brightness to the required level by holding down the switch. 2. Once the set point is reached, make a double click (switch pressed twice briefly within short time) within 30 s. The brightness will change. When the switch is released the luminaire will remain at the brightness it has reached. The brightness you have just set will be stored as the new set point. The luminaire will flash twice to confirm that this value has been stored. OSRAM - operating instructions TOUCH DIM LS/PD LI page 5
6 Operation Switching off at the switch, switching on via motion detection If the luminaire is has been switched off at the switch, then it will not be switched on automatically via the motion detector until an interval of 60s without movement has elapsed. Every further detected movement within this time retriggers the interval. After this interval the next detected motion will switch on the luminaire, provided that artificial light is needed. Deactivation of the brightness control Brightness control can be completely deactivated: 1. If the luminaire is switched on, switch off the luminaire by briefly pressing the switch. 2. Make a double click (switch pressed twice briefly within short time). The set point is erased and brightness control is now disabled. To activate the brightness control again, store a new set point as described on the previous page. Deactivation of the motion detection / Holiday mode If desired the motion detection can be deactivated. The brightness must not be manually changed 30 seconds before this holiday mode is activated. 1. Make a double click (switch pressed twice briefly within short time) The luminaire is switched off. Motion detection is deactivated until the luminaire is switched on again at the switch. page 6 OSRAM - operating instructions TOUCH DIM LS/PD LI
7 Appendix Troubleshooting The luminaire is not working. Possible cause: There is no power. Check if the luminaire is connected to power. The lamps are faulty. Replace them. The luminaire was switched off at the switch. Switch the luminaire on. The sensor is overexposed to ambient light. Cover the sensor and observe how the luminaire behaves. The luminaire is not regulating its brightness to the set point. Possible cause: After setting the brightness you must press the switch twice within 30 seconds. If you press the switch later you will activate holiday mode. Bear this time in mind. Brightness control is not started until 5 seconds after the set point has been set. Within this time any other switch operations are ignored. Bear this time in mind. Brightness control was deactivated by changing the brightness level with the switch. Switch the luminaire off and on again. Brightness control is deactivated because set point was erased. Store a new set point. The luminaire is not switched on automatically by the motion detector. Possible cause: The luminaire was switched off less than 30 s ago at the switch. Please note: after the luminaire is switched off, motion detection is deactivated for 30s. The motion detector is not covering the workplace. Wave your hand in front of the sensor and observe how the luminaire behaves. If the luminaire reacts to the movement, realign the luminaire over the workplace. More than adequate natural daylight is available and no additional artificial light is needed. The holiday mode is active. For deactivation of the holiday mode please press the switch Holiday mode cannot be activated. Possible cause: The brightness level was changed at the switch less than 30 seconds ago. Wait at least 30 seconds after changing the brightness before activating holiday mode. The luminaire is not reacting as expected to switch operations. Possible cause: The switch is being pressed too long. Please note: Hold down the switch to change the brightness until the luminaire reaches the brightness level you want. For all other functions, just briefly press the switch. If you cannot remedy the problem, please contact the customer service department of your luminaire manufacturer. OSRAM - operating instructions TOUCH DIM LS/PD LI page 7
8 Appendix Technical data Designation: Operating voltage: Connections: Interface: overall length of signal connection: Power consumption: TOUCH DIM LS/PD LI, light and presence sensor V AC / 50 60Hz (no DC operation) L, N, S (signal) OSRAM specific, max. 4 QTi LI ECG or. 4 HTi transformers connectable Max. 10 m approx. 0,5 W Operating temperature: 0C C Adjustable light value: lux measured at sensor resp. approx lux at desk surface Presence Detection area: conical, approx aperture angle Pollution severity: 2 Dry, not conductive to IEC 664 CE requirement: EMC to EN Dimensions: 63 x 29 x 21mm (L x W x H) Protection class: Protection type: IP 20 II The CE symbol signifies compliance with the relevant EU Directives. page 8 OSRAM - operating instructions TOUCH DIM LS/PD LI
luxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationShort operating instructions
gottardo LED office floor lamp series I Short operating instructions Visit us online too. gottardo-led.swiss Product film on Youtube Operating instructions gottardo series I Version: 1.0/20180406/SN SW:20170224
More informationData sheet. Function description. Benefits
uminaire-integrated modules SESOTEC MB Sensor Modules 110042808 SESOTEC MB HF1 COM1 110051733 SESOTEC MB HF1 DAI 110059684 SESOTEC MB HF2 COM1 Function description With the new HF sensor modules, you,
More informationluxcontrol lighting control system DALI sensors basicdim RCL DBC Control module for combination with ambient light sensor, switch and presence sensor
basicdim RCL DBC Control module for combination with ambient light sensor, switch and presence sensor Digital control module with ambient light sensor, motion detector and switch input DALI Broadcast control
More informationEBDSM-PRM Product Guide
EBDSM-PRM Product Guide Ceiling PIR presence/absence detector Overview The EBDSM-PRM PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual control.
More informationluxcontrol lighting control system DSI sensors smartdim SM lp Control module for combination with ambient light sensor, switch or presence sensor
Control module for combination with ambient light sensor, switch or presence sensor Product description Digital DSI control module (luminaire installation unit) for daylight control, motion detector and
More informationluxcontrol DALI MSensor 5DPI 14 Product Manual
luxcontrol DALI MSensor 5DPI 14 Product Manual ... c 2 / 48 Table of Contents Table of Contents 1 Validity.......................................................................... 5 1.1 Copyright.............................................................................
More informationSwitch actuator. Movement detector Move/monitoring 1305/1.0, Art. No , ,
0.0.1 Move/monitoring 1305/1.0, Art. No. 6316.., 6326.., 6318.. General Application 1305/1.0 has been developed for the KNX movement detector, Merten article numbers 6316.., 6326.. and 6318... In the following
More informationMOTION DETECTOR WITH CONSTANT LIGHT CONTROL DM KNT 003
MOTION DETECTOR WITH CONSTANT LIGHT CONTROL DM KNT 003 INSTRUCTIONS MANUAL Tel.: +34 943627988 E-mail: knx@dinuy.com Web: www.dinuy.com General Description Indoor universal mechanism box mounted KNX motion
More informationLight Management Systems for Indoor Use MULTISENSORS
Light Management Systems for Indoor Use MULTISENSORS MULTISENSORS Daylight and motion sensors both enable greater energy savings to be made and increase the convenience factor. For this reason, we have
More informationOT FIT 15/ /500 LT2 LP
www.osram.com Preliminary OT FIT 15/220-240/500 LT2 LP SELV Constant current LED driver Wide operating area up to 500mA The reliable component when LEDset flexibility, small dimensions and low ripple are
More informationEBDSPIR-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDSPIR-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDSPIR-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More informationThe universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal.
, GH Q631 0026 R0111 SK 0097 B97 The universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal. The device has 32 freely programmable inputs/outputs,
More informationRadio motion detector comfort 1.1 m/2.2 m quicklink Order number
Radio motion detector comfort 1.1 m/2.2 m quicklink Order number 8534 51.. Operating instructions 1. Safety instructions Electrical equipment may only be installed and assembled by a qualified electrician
More informationRadio bus system Radio-universal dimming actuator, 1-gang. 1 Safety instructions. 2 Device components. Order-No. : Operating instructions
Order-No. : 1135 00 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure to observe the instructions may cause damage
More information1 Safety instructions. 2 Device components. Radio bus system. Radio socket outlet adapter for dimming Order No. : Operating instructions
Order No. : 1185.. Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationABB i-bus EIB Light controller LR/S and light sensor LF/U 1.1
Product manual ABB i-bus EIB Light controller LR/S 2.2.1 and light sensor LF/U 1.1 Intelligent Installation Systems Contents Page 1. Notes............................................... 2 2. Light intensity
More informationKNX manual 1-channel flush-mounted switch actuator SU 1
KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product
More informationRev ABB i-bus KNX 6151/11 U-500. Power and productivity for a better world TM
1 73-1-7831 Rev. 01 3.2012 6151/11 U-500 Power and productivity for a better world TM Page: 1 of 31 Switching actuator 1gang with binary Inputs, FM Actuator Article-no.: 6151/11 U-500 ETS search path:
More informationProduct Manual. ABB i-bus EIB / KNX. Universal Interface US/U Intelligent Installation Systems
Product Manual ABB i-bus EIB / KNX Universal Interface US/U 12.2 Intelligent Installation Systems US/U 12.2, Universal Interface, 12-fold, FM Contents Page 1 General.3 1.1 Product and functional overview..3
More informationFL ballasts Electronic dimming. PCA T8 ECO lp Y, 3x18 W and 4x18 W ECO T8
T8 PCA T8 ECO lp Y, x18 W and x18 W ECO T8 Product description Processor-controlled ballast with y inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DSI signal, switchdim
More informationHuman Centric Lighting System
Human Centric Lighting System PIR HHC24 HHC23 HHC245 Circadian Rhythm sensor with Tunable white LED driver Lighting can reduce energy bills, it also can boost productivity and promote the wellbeing of
More informationFL ballasts Electronic dimming. PCA T5 ECO lp Y, 3x14/24 W and 4x14/24 W ECO T5
T5 PCA T5 ECO lp Y, x1/ W and x1/ W ECO T5 Product description Processor-controlled ballast with y inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DSI signal, switchdim
More informationLCC1653, LCC1656, LRI1653 Datasheet ActiLume DALI System
1/8 Product description The Philips ActiLume lighting control system consists of a small, lightweight sensor and controller, designed for easy integration into luminaires. ActiLume is a true Plug and Play
More informationFixture Built-in Sensor Daylight Harvest Version
Fixture Built-in Sensor Daylight Harvest Version Model: HC419VRC /DH Infrared remote receiver Detection area Hold-time Daylight sensor Buzzer Sensor antenna Photocell Installation hole (4.2mm) 4.2 45 Stand-by
More informationProduct and Applications Description
Product and pplications Description Diagram The transmitter 230V wave UP 110 (Diagram ) is a flushmounted device with radio communication for the wireless operation of room functions. It is possible to
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Order No. : 5490.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationPCA ECO lp Y, W T8 fluorescent lamps
T8 PCA ECO lp Y, 58 W T8 fluorescent lamps Product description Processor-controlled ballast with y inside Noise-free precise control via DSI signal, switchdim or corridorfunction CELMA energy class A1
More informationData sheet. Constant current LED control gear 26 W, 350 / 500 / 700 ma, DALI, 1 10 V Intelligent temperature protection SELV output.
Data sheet Constant current LED control gear 26 W, 3 / / 7 ma, DALI, 1 1 V Intelligent temperature protection output Kompakt III LED Kompakt III LED control gear More than 2 years of experience in the
More informationRoHS. Electronic ballasts for dimming to 1 % Linear lamps T5, 16 mm high efficiency, high output
T5 1 8 V 5// Hz RoHS D,1,95 1 side fixing feature side fixing feature,1 world first: first processor-controlled ballast with inside operation of T5 lamps of the same length (e.g. FH 8 / FQ 5 ) automatic
More informationRF Wireless Version On/off Control
RF Wireless Version On/off Control HC08V/RF + HC0RF Loop in 8 hours Detection Pattern 0 /88 / 5 /95 MHz Ambient daylight threshold Loop out manual on Condominium control 5s~0min ~50Lux Rotary coding switch(tx)
More informationProduct Specification
Product Specification Project: Microwave motion sensor Version:5.0 Date: 24/12.2008 Model : HC001S Pages:15 1 Objective The objective of this microwave motion sensor is to provide automatic intelligent
More informationFL ballasts Electronic dimming. PCA T8 ECO lp Y II, W ECO T8
T8 PCA T8 ECO lp Y II, 18 58 W ECO T8 Product description Processor-controlled ballast with y II inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DALI or DSI signal,
More informationTechnical data: Instabus EIB supply Voltage: YY 6 x 0.6 mm; red: bus (+) / black: bus (-)
Product designation: switching actuator 2fold 6A FM Design: FM (flush-mounted type) Article no.: 1057 00 ETS search path: Gira Giersiepen / Output / Binary output, 2fold / switching actuator 2fold 6A FM
More informationEBDHS-MB-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDHS-MB-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDHS-MB-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More informationEC5401B. B-Tronic EasyControl. Assembly and Operating Instructions. Wall/hand-held transmitter, 1-channel, bidirectional
B-Tronic EasyControl EC5401B en Assembly and Operating Instructions Wall/hand-held transmitter, 1-channel, bidirectional Important information for: Fitters / Electricians / Users Please forward accordingly!
More informationUniversal Radio Cord Dimmer Order No.: Function
Order o.: 0335 0 a) b) Function The permits radio-operated control of lighting fixtures. The device permits switching (short actuation) or dimming (long actuation) of the lighting. The dimmer is operated
More information1: White buttons Used by the user on a daily basis. 2: Grey buttons Used only upon first startup.
Fig. 1 Lock/ unlock 30 1000 Light 1 100 300 zone 1 Learn actual lux LED 600 2000 0,4 0,6 0,8 1,0 1,2 Time 1 Light 2 zone 2 1,4 1,6 Factor of lux zone 1 Pulse 2min 5min Time Time 2 10min 15min 30min 1 2
More informationOPTOTRONIC Intelligent
OPTOTRONIC Intelligent Dimmable DALI Areas of application _ Installation in emergency lighting systems according to IEC 61347-2-13, appendix J _ Suitable for use in luminaires with flexible current setting
More informationBossDim RS. User manual - UK
BossDim RS User manual - UK Congratulations on acquiring your new BossDim RS We are happy you have chosen our product to control your home lighting, and we hope it gives you hours of pleasure. On the following
More informationInstaller manual inputs/outputs interface for led KNX
Installer manual 01514 2 inputs/outputs interface for led KNX Exclusion of liability: Despite checking that the contents of this document match the hardware and software, deviations cannot be completely
More informationanimeo KNX/EIB 4 AC Motor Controller WM/DRM V AC
somfy.com animeo KNX/EIB 4 AC Motor Controller WM/DRM 220-240V AC Installation manual Ref. 1860114 Ref. 1860116 2007, SOMFY SAS. ALL RIGHTS RESERVERD. REF. 5050779-30/04/2007 Table of contents Introduction...
More informationWidth (W): 44 mm. bus connecting and branching terminal External supply --- Inputs: Number: up to 2 (depending on parameterization: channel 1 to 2)
Product name: Design: 2-channel push button interface UP (flush-mounting type) Item no.: 1118 00 ETS search path: Gira Giersiepen / input / binary input, 2fold / Universal push putton interface 2fold Functional
More informationTechnical data lumina MS4/RC
Technical data 1. Product description The LON multisensor lumina MS4/RC is a combination of occupancy sensor, two light sensor, external temperature sensors, infrared remote control receiver and EnOcean
More informationinstabus EIB product documentation
Page: 1 of 39 Push button interface 4-gang Sensor Product name: Push button interface 4-gang Design: UP (flush-mounting type) Item no.: 2076-4T-01 ETS search path: Input / Binary Input, 4-gang / Push button
More informationL DN 2810 FL DE 3925 L DN 2810 FL PIR DE 3925 L DN 5630 FL DE 3925 L DN 5630 FL PIR DE 3925 L DN 9850 FL DE 3925 L DN 9850 FL PIR DE 3925
D Operating instructions Slim LED Light L DN 2810 FL L DN 2810 FL PIR L DN 5630 FL L DN 5630 FL PIR L DN 9850 FL L DN 9850 FL PIR Attention: efore assembly of the light, please carefully read the operating
More informationActiLume G2 Indus Sensor H513
LRI1667 Product guide ActiLume G2 Indus Sensor H513 The Philips ActiLume G2 Indus Sensor H513 is a small, lightweight multisensor designed for integration into luminaires. The ActiLume G2 Indus Sensor
More informationFL ballasts Electronic dimming. PCA T5 EXCITE lp Y, 3 and 4x14/24 W EXCITE T5
T PCA T EXCITE lp Y, and x1/ W EXCITE T Product description Processor-controlled ballast with y inside Highest possible energy class CEMA EEI = A1 BAT 1 oise-free precise control via DAI or DSI signal,
More informationInstruction manual. art Installation manual
Instruction manual art. 01521 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 4 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL FEATURES AND
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
FSP-2X1 Digital High/Low Pir Fixture Integrated Sensor INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
More informationABB i-bus KNX DALI Light Controller DLR/S M Product Manual
ABB i-bus KNX DALI Light Controller DLR/S 8.16.1M Product Manual ABB i-bus KNX Contents Contents Page 1 General... 3 1.1 Using the product manual...4 1.1.1 Structure of the product manual...4 1.1.1.1
More informationActiLume 1-10V. OEM application guide
ActiLume 1-10V OEM application guide Contents Contents 1 What is the ActiLume 1-10V System 3 2 System characteristics 4 2.1 ActiLume 1-10V Sensor LRI 1655/00 4 2.2 Movement detector 5 2.3 Light sensor
More informationSeeTool - Solutions for KNX
SeeTool - Solutions for KNX Office building segment Application 8.2.1.0.0.4 Movement dependent automatic light control with light regulation and manual control, temperature control (electrical heating
More informationFSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR
FSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR CAUTIONS INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including
More informationSIMPLUX Standalone Wireless Lighting Control System Setup guide Light is OSRAM
www.osram-americas.com SIMPLUX Standalone Wireless Lighting Control System Setup guide Light is OSRAM Setting up the SIMPLUX System! Only one phone should be used for SIMPLUX System configuration at any
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Art. No. : FM..1561.07.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationRF ceiling microwave presence detector DALI / DSI
MWS3A-AT-DD Product Guide RF ceiling microwave presence detector DALI / DSI Overview The MWS3A-AT-DD is a passive microwave motion sensor combined with two output channels capable of controlling incandescent,
More informationRAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL
RAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL 1 Contents 1. Application... 5 2. meter set... 6 3. BASIC REQUIREMENTS, OPERATIONAL SAFETy... 6 4. installation... 10 4.1. Mounting... 10 4.2. External
More informationOperating instructions Flat-Type Wall-Mounted Radio Control
Operating instructions Flat-Type Wall-Mounted Radio Control Insert 1. Function The wall-mounted radio control insert permits remote control of all receivers of the Funk-Management system. This wall-mounted
More informationLLC1681, LRI1655 Datasheet ActiLume Wireless 1-10V system
1/7 Product description The Philips ActiLume Wireless 1-10V lighting control system consists of a small, lightweight sensor and a switchbox (controller), designed for easy integration into luminaires.
More informationWireless wall transmitter, 1-gang with inscription space, Wireless wall transmitter, 3-gang with inscription space
Wireless wall transmitter, 1-gang with inscription space Order No. : 5331.. Wireless wall Order No. : 5333.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected
More information1 Safety instructions. 2 Device components. 3 Function. Radio bus system. Radio socket-outlet adapter for switching Order No. :
Order No. : 0401.. Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationEBDHS-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDHS-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDHS-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More informationABB i-bus KNX DALI-Light Controller DLR/A Product Manual
ABB i-bus KNX DALI-Light Controller DLR/A 4.8.1.1 Product Manual ABB i-bus KNX Contents Contents Page 1 General... 3 1.1 Using the product manual...4 1.1.1 Structure of the product manual...4 1.1.1.1
More informationNOVA series Ceiling lights with tuneable white Colour temperature 2700 to 6500 K. Detailed operating instructions
NOVA series Ceiling lights with tuneable white Colour temperature 2700 to 6500 K Detailed operating instructions 1 EN Version Date Comment BA01079601 31.10.2016 Second edition ESYLUX GmbH An der Strusbek
More informationOTi DALI 80/ / CH OTi DALI 50/ / CH
www.osram.com OTi DALI 80/220-240/24 1-4 CH OTi DALI 50/220-240/24 1-4 CH 24 V DALI Constant Voltage LED driver Dimmable range 0% - 100% Benefits Slim form factor for mounting on the cove or in linear
More informationQL50 Luminescence Sensor
Compact, self-contained luminescence sensor LISTED US Compact, self-contained design Features Senses luminescent marks, even on luminescent backgrounds and on reflective surfaces, such as ceramic, metal,
More informationB-Tronic EasyControl EC5401B
B-Tronic EasyControl EC5401B en Assembly and Operating Instructions Wall/hand-held transmitter, 1-channel, bidirectional Important information for: Fitters / Electricians / Users Please forward accordingly!
More informationProduct Catalog 2013 Made in EU
Product Catalog 2013 :. Made MADE IN EU in.: EU www.lumeca.de WWW.LUMECA.DE 1 2 WWW.LUMECA.DE :. MADE IN EU.: CONTENT STREET LIGHTING SPOTLIGHTS SOLAR LIGHTING PARK AND PEDESTRIAN LIGHTNING SMART CONTROL
More informationZITARES CCD FX-20 25W SELV (isolated), adjustable functions and current, 1-channel, dimmable
Sample image ECG versions Model Order no. Output current 1) Output power CCD175-25FX-20/220-240/LI 10132980 100... 750 ma 2... 25 W 1) Adjustable by means of zitares360 software or resistor. Performance
More informationPHASED OUT. Digital dimmable ballasts for fluorescent lamps EXCEL series. PCA TCL EXCEL one4all lp Y, 55 W Compact and T5c fluorescent lamps
EXCE series Product description Processor-controlled ballast with y inside oise-free precise control via DSI signal, switchdim, corridorfuctio or I I-MEMORY Extended I commands OEM-specific reserved memory
More informationdesign by Antonio Citterio with Toan Nguyen
design by Antonio Citterio with Toan Nguyen introducing Kelvin LED Green the world s first interactive task light design by Antonio Citterio with Toan Nguyen a new vision in LED technology Introducing
More informationThe room thermostat application module with 2-fold switch sensor is placed on a flush-mounted bus coupler.
The room thermostat application module with 2-fold switch sensor is placed on a flush-mounted bus coupler. The room thermostat with 2-fold switch sensor offers the possibility of implementing single room
More informationSingle-colour Dimming: Hand-held Transmitter 2801E Data Sheet
Hand-held Transmitter 2801E Data Sheet Hand-held transmitter 2801E The Transmitter 2801E is a radio transmitter module designed as a hand-held remote control unit. Together with a separate receiver module
More informationZITARES CCD 2 nd Generation SELV constant current control gear, 1-channel, dimm- and adjustable
ECG versions Model Order no. Output currents 1) Output power CCD1150-50FR-20/220-240/LI 10116443 1 x 500... 1500 ma 11... 50 W 1) Adjustment by means of software or resistor Performance characteristics
More informationanimeo KNX 4 DC 2 A Motor Controller WM 24 V DC Installation manual
somfy.com animeo KNX 4 DC 2 A Motor Controller WM 24 V DC Installation manual Ref. 1860128 2008-2013, SOMFY SAS. ALL RIGHTS RESERVED. REF. 5059105C - 2013/04/30 Table of contents 1 2 3 4 5 6 7 8 9 10 Introduction...
More informationTD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual
TD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual Item no.: NT-244-101 1. Product Description The TD-Power Supply SC DALI & Switch Dim Mono is a dimmable 24V constant voltage LED driver
More informationluxcontrol lighting control system Sensors smartswitch 5DP 14f Automatic switching based on presence and light level
luxcontrol lighting control sstem smartswitch 5DP 14f Automatic switching based on presence and light level Product description Motion detector for luminaire installation For automatic on/off switching
More informationIRIS \ IRIS-I QUICK SET-UP GUIDE STEP 1 INSTALL
IRIS \ IRIS-I QUICK SET-UP GUIDE STEP 1 INSTALL Confirm contents of package: 1 sensor, 1 cable, 1 wide lens (default), 1 narrow lens, mounting template, User s Guide. Install the sensor at the desired
More information3000W multi Pir light controller
3000W multi Pir light controller Cat No. MLB3000 - Black Cat No. MLW3000 - White Installation & Operating Instructions INSTALLATION & operating instructions SECTION ONE GENERAL INFORMATION The unit utilises
More informationApplications. HBT02 Transceiver Node. Features. Note: This datasheet is intended for information related to the hardware only.
Synchrony ighting Control With Wireless Technology HBT01 / HBT02 with HC038V / HCD038 Built-in Detachable Version Applications The freedom of wireless mesh networks configured by smartphone APP s considerably
More informationalready there. LUMILUX T8 Subheadline
The most Headline important with part Glow is Subheadline already there. LUMILUX T8 Did you know that...... in Europe more than 90% of the demand for artificial light is covered by discharge lamps? And
More informationPhilips Ledalite Phone: Fax: Web: Programming Guide Version 2.0
Philips Ledalite Phone: 604.888.6811 Fax: 800.665.5223 Web: www.ledalite.com Programming Guide Version 2.0 AIRWAVE PROGRAMMING GUIDE 1.0 Linking/Unlinking an Airwave Switch or Photosensor to a Transceiver
More informationZITARES ICD SELV constant current control gear, 2-channel, dimm- and programmable
ECG versions Order number ICD90-0QS-0/0-0/LI 00907 ) ) Output current Total power output x 0... 900 ma... 0 W Additional output currents can be selected by parallel connection of the outputs of the ECG,
More informationHigh/Low Bay Passive Infrared Occupancy Sensor
Models Sensors: HBP-111-L7, with IR remote capability HBP-112-L7, no IR capability High/Low Bay Passive Infrared Occupancy Sensor Mounting Modules: HBP-EM1 extender module HBP-SM1 surface mount module
More informationBinary Inputs. Ref.-No. KNX universal binary input, 8-gang. ETS-product family: Series embodiment (SE-) device (2 units) Ref.-No.
Binary s 1 L1 L2 L3 N E1 N1 E2 N2 E3 N3 E4 N4 KNX + - 2 1 KNX universal binary input, 4-gang ETS-product family: Product type: Series embodiment (SE-) device (2 units) Ref.-No. 2114 REG 4-gang binary input
More informationABB i-bus KNX Weather Sensor, SM WES/A 3.1, 2CDG120046R0011
Technical Data 2CDC504093D0202 ABB i-bus KNX Product description The Weather Sensor WES/A 3.1 detects primarily in the residential sector wind speed, rain, brightness in three directions, twilight, temperature
More informationDialight Daylight Harvesting Sensor User Guide
Daylight Harvesting Sensor Dialight Daylight Harvesting Sensor User Guide Dialight Catalog Number: DLHU124UG2 1 Safety Instructions Dialight Daylight Harvester Sensor (DLH) User Guide READ AND FOLLOW ALL
More informationHeat pipe technology to cool LEDs. Powerful light, precisely where you need it.
Heat pipe technology to cool LEDs. Powerful light, precisely where you need it. Manufactured by Company Name XX th Month 20XX Other designers have made attempts to cool LEDs. But it s not enough. They
More informationShutter Actuator with Manual Operation, 4-fold, 230 V AC, MDRC JA/S M, GH Q R0111. ABB i-bus EIB / KNX
, GH Q631 0064 R0111 Technical data 2CDC 071 234 F0003 For controlling 4 independent shutter or sunblind drives, 230 V AC, via ABB i-bus including the functions Up/Down, Step/Stop, Move to position, Sun
More informationAutomatic-switch (1,10m): Standard attachment Order No.: Automatic-switch (2,20m): Standard attachment Order No.:
(1,10m): Standard attachment Order No.: 0832.. Comfort attachment Order No.: 0833.. System attachment Order No.: 0842.. (2,20m): Standard attachment Order No.: 0839.. Comfort attachment Order No.: 0838..
More informationFL ballasts Electronic dimming. PCA T8 EXCEL one4all lp Y II, W EXCEL T8
F ballasts E T8 PCA T8 EXCE oneall lp Y II, 18 58 W EXCE T8 Product description Processor-controlled ballast with y II inside Highest possible energy class CEMA EEI = A1 BAT 1 oise-free precise control
More informationUMG 96L / UMG 96. UMG 96L / UMG 96 Universal measurement device. Threshold value monitoring. Pulse outputs. Networks TN-, TT-Networks
Threshold value monitoring Pulse outputs UMG 96L / UMG 96 Universal measurement device Measuring accuracy Energy: Class 2 Current.../1 A,.../5 A Voltage L - N: ± 1 % Networks TN-, TT-Networks 2 digital
More informationKNX ENO 620/622 (32-channel AP)
KNX O 620/622 (32-channel AP) Gateway between EnOcean and the KNX bus Operating and installation manual Installation and connection Fig. 1: KNX O 620 Fig. 2: KNX O 622 Application KNX O 620 and 622 serve
More informationZITARES ICD SELV constant current control gear, 2-channel, dimm- and programmable
ECG versions Model Order no. Output currents 1) Output power ICD290-60LS-01/220-240/LI 10105905 2 x 250-900 ma 5-60 W ICD290-100LS-01/220-240/LI 10105906 2 x 250-900 ma 12.5-95 W 1) Adjustable for each
More informationRadio Touch Order no.: 2880 xx. Operation and installation instructions. 1 Safety instructions. 2 Structure of the device (Figure 1) Radio Touch
Radio Touch Order no.: 2880 xx Operation and installation instructions 1 Safety instructions Electrical equipment must only be installed and assembled by a qualified electrician in accordance with the
More informationZoneLite setup remote handset. Daylight Linking & Daylight Dependency control
ZoneLite control unit The new Flex Connectors ZoneLite is an intelligently configurable all in one lighting control solution for many commercial lighting applications. Control can vary from ON/OFF/DIM,
More informationE N SHT-1 SHT-1/2 SHT-3 SHT-3/2
Digital time switch E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Content Symbol, Connection... 3 Warning... Characteristics... 5 Technical parameters... 6 Versions of time switches, Load... 7 Description... 8-9 Control...
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Order No. : 2126 00 Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationLK Wireless Room Control Cq
LK Wireless Room Control Cq Description LK Wireless Room Control Cq consists of a LK Room Thermostat Cq-n (transmitter) and a LK Receiver Unit Cq 8 (8 channel receiver unit). The range also includes a
More information