TS10 HV500 HV5008. Operating Instruction Manual

Transcription

1 Tanning System TS10 HV500 HV5008 Operating Instruction Manual

2 Exploded Parts Drawing TS Description Part No. 1. Air Cap Ring L Air Cap L Spray Direction Plate L Fluid Tip L Fluid Tip Seal L Needle L Spring L Solution Flow Screw L Gland Nut L Gland Seal L Container Seal L Clip M Pick-upTube L ml Container L Hose L0543 Description Part No. 1. Air Cap Ring L Air Cap L Spray Direction Plate L Fluid Tip L Fluid Tip Seal L Needle L Spring L Solution Flow Screw L Gland Nut L Gland Seal L Pick-up Tube L Container Seal L ml Container L Hose Assembly(HV5008)L Filter L Hose Assembly(HV500) L0543 HV HV Position the pick-up tube on the pick up port closest to the gun handle 2

3 Safety Instructions Only use the tanning equipment as detailed in these instructions. The tanning solution must not be inhaled. We recommend that your clients use nose plugs. We recommend that your clients use goggles to protect their eyes during spray tanning. Advise your clients not to wear deodorant, perfume or make-up for the spray tanning session as these products could affect the performance and colour of the tan. Advise your clients to remove any jewellery before the spray tanning session starts as this may become discoloured. Advise your clients to shave or wax 24 to 48 hours before their spray tanning session is due. Advise your clients to always cover their hair while their face is being spray tanned, especially if their hair is bleached as this can be stained by the tanning solution. Make sure the area where you spray tan is adequately ventilated. Do not apply tanning solution to open cuts, broken or damaged skin. Cosmetics may cause a mild reaction if your client has sensitive skin. Advise your clients to avoid wearing light coloured clothing after spray tanning. If tanning solution is sprayed into the eyes, flush them out with water and seek medical advice immediately. Never immerse the motor unit in water. Warning. Do not use your spray tan equipment near bathtubs, showers, basins, or other vessels containing water. Always dis-connect the motor unit from the mains supply when re-filling the spray gun container or when cleaning the tanning equipment. If you use your spray tan system close to a hand basin, shower or a similar source of water, unplug it after use because the proximity of water presents a hazard even when the equipment is switched off. 3

4 Safety Instructions When the appliance is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the appliance is switched off. For additional protection, the installation of a residual currecnt device (RCD) having a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice. Note: Mains socket might not be permitted in average sized bathrooms according to local wiring regulations. Do not spray into light switches or power sockets. This appliance can be used by children aged from 8 years and above persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Never allow children to operate, or play with, the tanning system. Never spray or aim the spray gun at animals or livestock. We recommend that you clean your spray equipment after every use. Use only genuine manufacturer replacement parts. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels containing water. IMPORTANT: Patch Test We recommend testing the tanning solution and the other cosmetics on a small area of your clients skin 24 hours before spraying a large area. If irritation occurs discontinue use. 4

5 Preparing your equipment for use Your tanning equipment is supplied as 2 main components, the motor unit, which includes the hose, and the spray gun. Please refer to the exploded drawing on page 2 and follow the simple instructions below. Unscrew the Container from the spray gun and fill it with tanning solution. Do not overfill the Container. Normally 50ml of solution is enough for one application. Make sure the Pick-up Tube is pushed firmly into the lid of the spray gun. Carefully screw the Container back into the lid of the spray gun, ensuring there is an airtight seal. Connect the hose to the spray gun by pushing it firmly into the hose inlet at the back. Uncoil the mains cable from the base of the motor unit and connect the mains plug to a suitable 230V supply socket. Switch on the motor unit. No tanning solution will be sprayed until you pull the spray gun's trigger. Before operating the unit please ensure that the container is securely fixed to the gun body and the Gland Nut is not loose. Doing this will create an airtight seal, that is essential for the correct operation of the unit. Over time the Gland Seal will wear and need adjusting. To check the Gland Nut is correctly fitted you will need a small adjustable spanner. Pull the trigger back and gradually tighten the Gland Nut by turning it in a clockwise direction until the Needle is not free to move when the trigger is released. To obtain the optimum setting gradually unscrew the nut by turning it in an anti-clockwise direction until the Needle moves forward into the Fluid Tip. To check your settings are correct spray a container of water. Re-adjust if necessary. Body Preparation Careful preparation of your clientʼs skin is the key to a perfect tan. Please follow the steps below. Exfoliate This is the most important step in preparing the body for spray tan. It is important to remove dead cells from the surface of the skin as these act as a barrier. Removing them will ensure a longer lasting and even tan. Pay attention to the dry areas of the skin on the knees, elbows, ankles and the tops of the feet. Moisturise Moisturise dry areas of skin on knees, elbows, and ankles with moisturising lotion to get an even tan, matching the rest of the body. The moisturiser acts as a barrier since these areas tend to absorb more solution and therefore tend to be darker than the rest of the body. Do not moisturise all of the body. Wait for the moisturiser to dry completely before you spray tan your client. Apply Balm Use a barrier balm to prevent your clientsʼ nails and the palms of the hands from staining. Use the balm to protect your clientsʼ lips. Cover your clientsʼ hair especially if they have bleached hair before you spray tan the face. You can use a little balm on the hairline and eyebrows. Setting up the Spray Gun Before beginning a spray tan session, we recommend that you set the spray pattern and the amount of solution to be sprayed to your own preferred requirements. 5

6 Adjust the spray pattern by rotating the air cap as shown in Fig.1. There are three patterns to choose from, horizontal, vertical and round. We recommend that you use a horizontal spray pattern when spraying the upper part of the body and a vertical pattern for the lower body. Adjust the volume of solution applied by adjusting the Solution Flow Screw, at the back of the spray gun (Fig.2). Turn it clockwise to reduce the amount of solution and anti-clockwise to increase it. It is a good idea to practice spraying onto a piece of plain, white paper until you find the pattern and volume that is best for you. Fig.1 Fig.2 Some do's and don'ts when spray tanning. If you are not spraying in a purpose built booth or room, avoid spraying close to porous materials, such as tile grout or untreated timber, drapes, carpets or similar fabrics. Materials may be stained by any overspray of the tanning solution. The spray gun can be adjusted to deliver the correct amount of solution by turning the Solution Flow Screw turn it clockwise to reduce the amount of solution, and anti-clockwise to increase it. (see Setting up the Spray Gun ) You can adjust the spray pattern to suit your own preferred way of spraying by adjusting the Air Cap as shown in Fig.1. As a guide, we recommend that you use a horizontal spray pattern when spray tanning the upper part of the body and a vertical pattern for the lower body. (see Setting up the Spray Gun ) When spraying the face, we recommend for maximum safety that your client wears nose plugs, to ensure no tanning solution is inhaled, and goggles to protect the eyes. Alternatively, ask your client to take a breath and close her/his eyes while you take just a few seconds to apply the solution to the face. If any solution gets into your client's eyes, wash them out and seek medical advice. We also recommend that hair should be covered. As a guide, the spray gun should be held between 10cm (4 Inches) and 25cm (10 Inches) from your client's body and face. When being spray tanned, your client should stand with feet apart and arms held away from the body. Always start and finish each pass of the spray gun off the body. This will ensure an even tan. It is important to keep the spray gun moving at a constant speed to achieve an even tan. If you move the spray gun too slowly, and the solution runs down your client's body, simply blot away the excess with a foam sponge, or baby wipe, and re-spray the affected area. For a more natural looking tan, we recommend that the spray gun is moved more quickly to give a light coverage to areas such as the inside of arms and legs. When you have finished spray tanning, you can use the spray equipment to blow warm air over your client to help to dry the tan more quickly. 6

7 After Spray Tanning Allow your clients minutes after the spray tanning is complete for the tanning solution to dry completely, before getting dressed. Also advise them to wear loose fitting clothing and avoid light coloured clothes as they may be stained if the tan is not absolutely dry. The tanning solution is water based and will wash out of clothes if any staining should occur. The tan will develop over the first few hours and reach its deepest within 24 hours, but advise clients to wait for 6 to 8 hours before showering, or taking a bath, as this will inhibit the development of the tan. To maintain the tan, clients should moisturise daily and avoid long hot baths and showers, as this will speed up the natural process of exfoliation. Troubleshooting There is no tanning solution coming out of the spray gun 1. Check there is enough solution in spray gun container. 2. Make sure the spray gun is not clogged up with old tanning solution. Follow Cleaning and Maintenance instructions. Tanning solution is too runny 1. Spray volume maybe too high. It can be adjusted with the Solution Flow Screw Turn it clockwise to reduce the amount of solution (Fig.2). 2. When spraying, hold the spray gun further away from your clients body or move the spray gun faster. 3. You may not be spraying evenly. Keep the spray gun moving and do not overlap those areas already spray tanned. Tanning solution sprays irregularly 1. The solution volume maybe too low and this can be adjusted with the Solution Flow Screw by turning it anticlockwise until you get the desired volume (Fig.2). The tan is patchy 1. Ensure your client has exfoliated before spray tanning. 2. Ensure you spray tan in a methodical way to cover all areas. It is easy to see which parts have been sprayed. Keep the spray gun moving and do not overlap those areas already spray tanned. 3. Ensure that you spray tan lightly and in layers rather than one thick layer. Cleaning & Maintenance Always wash out your spray gun at least at the end of each day. If the tanning solution dries inside the spray gun, cleaning will become more difficult and the spray gun may become inoperable. To wash out your Spray Gun Switch off and disconnect the motor unit from mains supply. Unscrew the container from the main body of the spray gun. Pour any excess solution back into its orginal container for future use. Half fill the container with water and re-fit it to the spray gun main body, shake the spray gun lightly, re-connect the motor unit to the mains supply and spray the water through the gun. Repeat several times until the water is clear with no traces of tanning solution. Continue to spray the clean water until the container is empty. Run the spray gun for a further 2 minutes with just the air blowing through it. This will dry the inside of the spray gun preventing any contamination of the working parts. Clean any traces of tanning solution from the outside of the gun with a damp cloth. Wipe clean the Container Seal inside the lid of the spray gun. 7

8 Mains Connection This unit is a Class II appliance which means it is double insulated for your protection, no earthing wire is necessary. If the supply cord is damaged, it must be replaced by the manufacturer or our appointed agents. Your unit has been supplied with a mains lead with a fitted plug. This is identified by the fuse holder in the base of the plug. Please read the following safety instructions before use. 1. If the fitted plug is cut off from the mains lead then the plug must be disposed of safely. NEVER under any circumstances insert such a plug into a 13 Amp socket. 2. NEVER under any circumstances use the appliance or mains lead without the fuse cover fitted. This is the little cover fixed into the base of the plug to hold the fuse in place. 3. If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline. 4. A replacement fuse must be rated at 5 Amp. These must be manufactured and approved to BS IF IN ANY DOUBT CONTACT AN ELECTRICIAN. If you need to fit a plug to the mains lead, this should be fitted in accordance with the wiring instructions below, and will need to be used with a 5 Amp fuse. If in doubt consult an electrician. If you are using an extension lead it must be rated at a minimum of 6 Amps and fully unwound. Do not operate with a lead rated at less than 6 Amps as this will cause premature failure of the motor which is not covered by the guarantee. As the colours of the wires in the mains lead of the application may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. INFORMATION ON THE DISPOSAL OF WASTE ELECTRICAL EQUIPMENT KNOWN AS WEEE Your attention is brought to new directives applicable to the disposal of this electrical equipment, where in accordance with the legislation this product must not be disposed of in your normal household waste. Instead it is your responsibility to dispose of this type of waste by handing it over to special designated collection points for recovery and recycling. This product is marked with a ʻWheelie binʼ symbol with a cross on it to remind you of this action. The objective of this directive is to help conserve resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste please contact your local authority, take back facilities are free of charge. The EC Declaration of Conformity We declare that the unit: TS10 and HV5008 conforms to 2006/95/EC, BS EN , BS EN 62233, 2004/108/EC, EN , EN , EN , EN , EN Tim Hopper Technical Director TS10 Registered Design No: , EU , US D541, 903S, CA110591, AU 11299/2005, CN HV5008 Registered Design No: GB , FR 06/5463, EU , US D563,503 Copyright & Design Right Reserved 2010 Warranty There is a full 6 months warranty on your Professional Tanning System against faulty manufacture and materials, from date of purchase. This is offered over and above your normal consumer statutory rights. This warranty does not include damage to the product caused by incorrect use L /10 8