INSTRUCTION MANUAL. (Suitable for up to 100 sprays per day) Non-continuous use - up to 30 minutes use. The Hush Sprinter sound level is: 80db

Transcription

1 INSTRUCTION MANUAL HUSH HUSH SPRINTER endura TANNING SYSTEM (Suitable for up to 100 sprays per day) Non-continuous use - up to 30 minutes use The Hush Sprinter sound level is: 80db DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep for your reference. Please fill out the warranty card at the back to obtain warranty Solaire Pty Ltd Unit 5, 32 Essington Street, Grovedale, 3216, Australia. info@solaire.com.au Ph: International: +61 (3)

2 Table of Contents 1. General Safety Information: Set up and operate your Hush Sprinter Spray Tan System: Prepare the Hush Optimiser Spray Gun Adjusting the Hush Optimiser Spray Gun Spraying Maintenance Troubleshooting Warranty Card

3 HUSH HUSH SPRINTER endura Features Designed to perform, think a lot of tans in a week. Motor, pre-set for Spray Tanning delivers superior airflow. Commercial Grade Exterior Casing - easy cleaning. Heavy-duty rubber feet to protect floors 3.5 Meters lightweight, tough flexible hose Brass quick-connections to Machine and Gun Easy to fill, simply place gun on the holder and fill the cup 3/4 full. The miniature gravity cup holds 250ml Carry Handle Stainless steel 0.5 mm fine needle tip Only 8kg with gun, 7kg without 37cm Long x 25cm High x 24cm Wide Metal Connections\ 80 db 12 Month Warranty The Hush Sprinter By Solaire provides a superior performance delivering a flawless tan through a powerful yet whisper quiet motor. The name says is all - Sprinter - when performance is required. Hush Sprinter By Solaire Instruction Manual Congratulations on purchasing the Hush Sprinter tanning system. This product has been specially designed to provide the best application of professional spray tanning solutions. Take a minute to read and understand how to operate your new Hush Sprinter tanning system and you will be able to provide the perfect tan with every application. Your Hush Sprinter is packaged with the following: 1. Hush Sprinter unit m lightweight, tough Flexible Hose 3. Hush Optimiser Spray Gun 4. Instruction Manual (see website) 5. Warranty Card 3

4 1. General Safety Information Read all instructions and safety precautions before operating the unit. HUSH HUSH SPRINTER endura THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. THIS INDICATES A CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. THIS INDICATES A CONDITION THAT MAY CAUSE MINOR INJURY AND/OR EQUIPMENT/PROPERTY DAMAGE. GROUNDING INSTRUCTIONS This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical shock by providing an alternate path for the electrical current. This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet that is properly installed and grounded in accordance with local codes and ordinances. I IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL. THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE GROUNDING WIRE. 1. For any question regarding proper installation of the ground plug, consult a qualified (licensed or certified) electrician. 2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper outlet installed by a qualified electrician. Fig 1 3. This product is for use on a nominal 240-volt circuit and has a grounding plug that looks like the plug in Figure 2. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapters should be used with this product. 4. If an extension cord is required, use only a three wire extension cord that has the same configuration as the unit cord, including the ground terminal. Make sure that the extension cord is plugged into a properly grounded receptacle. 5. When using an extension cord, be sure it is in good condition and meets specifications. Fig 2 6. Ensure the Hush Sprinter is tagged and tested every 12 months after initial purchase to comply with Australian Electrical Safety standards. 7. Always turn off power switch of Hush Sprinter and remove plug after operation. 8. Be aware to hold the solid plug body to remove from socket. Never remove the plug by just pulling the flexible part of the power cord 9. Disassemble or maintenance of the Hush Sprinter is to be conducted by an authorised technician only as this voids all warranty. 10. Do not operate near water or moisture as electrocution may occur. 4

5 2. Set up and operate your Hush Sprinter Tanning System HUSH HUSH SPRINTER endura 1. Plug the Hush Sprinter tanning system unit into a proper electrical outlet. Make sure that the electric current you are connecting to is the same as your unit. (240v). DO NOT attempt to connect the unit to the wrong electric current as this will not only damage your unit but also void your warranty. 2. Next, locate the male end of the air hose and connect it to the female quick connect on the Hush Sprinter tanning system. a. To insert the male connection pull back on the ring of the black coupler located on the Hush Sprinter tanning system and insert the male connector on the hose. Figure 6. Fig. 6 b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the unit Figure 7. Fig. 7 c. To remove the air hose, pull back on the ring of the black coupler and remove d. See page 7 for How to connect the Hush Sprinter to the Hush Optimiser spray gun. To Turn the UNIT ON Press the red power switch button and use the variable control to set your airflow pressure. If you have just finished spraying, the connector may be hot. Allow the Hush Sprinter unit to cool down for about 10 minutes before disconnecting the air hose from the Hush Sprinter unit. Use Caution! 5

6 3 Prepare the Hush Optimiser Spray Gun: HUSH HUSH SPRINTER endura 6

7 3 Prepare the Hush Optimiser Spray Gun cont d HUSH HUSH SPRINTER endura 1. Follow the diagram to prepare the Hush Optimiser Spray Gun a. Unscrew the plastic cup from the Hush Optimiser Spray Gun. Pour tanning solution into the cup. Do not fill more than ¾ full. b. Carefully screw the cup back onto the main body of the Hush Optimiser Spray Gun. Screw the cup on firmly but DO NOT over tighten. Over tightening will cause the cup to pop and damage the threads. Leakage can then occur requiring replacement of the cup. c. Locate the air cap (#1) on the Hush Optimiser diagram. With the gun facing towards you, slightly turn the air cap ring (#1-1, page 6) anti clockwise to loosen the air cap. Notice that you can now rotate the air cap freely. d. Look at Mist Applicator Patterns diagram above. Note the position of the air cap and the direction of the spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down. Patterns 1 and 2 are the most common positions for applying tanning solutions. 7

8 3. Prepare the Hush Optimiser Spray Gun cont d HUSH HUSH SPRINTER endura e. Turn the air cap (#1) to the position you want. Again with the gun facing towards you, turn the air cap ring (#1-1, page 6) clockwise to lock the air cap in place. f. The spray pattern can be changed from flat to circle using the Pattern Adjusting knob (#12). A circle pattern (as seen below) can be used for contouring. Pattern Adjusting Knob How to mist in a spot or circle 2. Next, position the Hush Sprinter unit as far away as practical and possible from the area where you will be spraying. 3. Attach the remaining end of the hose to the Hush Optimiser Spray Gun as follows: a. Locate the male connection at the bottom of the Hush Optimiser Spray Gun. See figure 8. b. Pull back on the coupler of the brass connector on the air hose. Flow Solution Screw Fig 8 8

9 4. Adjusting the Hush Optimiser Spray Gun HUSH HUSH SPRINTER endura 1. Locate the Solution Flow Screw (#22, page 7) on the Hush Optimiser diagram. 2. Face the front of the Hush Optimiser gun away from you and turn the Solution Flow Screw clockwise. This reduces and will eventually stop the flow of solution. DO NOT over-tighten the screw as this will cause damage to the end of the needle. Once the trigger cannot be pulled back there is no point in tightening the screw down more, this will only damage the end of the needle. 3. Turning the Solution Flow Screw anti clockwise will increase the flow of solution and turning the solution flow screw clockwise will decrease the flow of solution. 4. In general, 1 ½ - 2 full turns from the fully closed position will provide a good solution flow. You may find that you want more or less solution. You can adjust the Solution Flow Screw to your desired setting. NOTE: Opening the Solution Flow Screw more than 3 turns will not increase the solution flow and will in fact decrease the efficiency of your Hush Optimiser Spray Gun. 5. In general, hold the Hush Optimiser Spray Gun 20-30cm from the person being sprayed. Moving the Hush Optimiser Spray Gun back will increase the size of the mist pattern. Moving the Hush Optimiser Spray Gun closer will decrease the size of the mist pattern. The further away you hold the Hush Optimiser Spray Gun, the more you will need to increase the solution flow thus causing abnormal amounts of airborne solution (overspray). 6. Holding the Hush Optimiser Spray Gun closer to the person being sprayed along with a minimum flow of solution will provide the best results, no streaks or running solution and virtually no mist in the spray area. 7. Be sure to move the Hush Optimiser Spray Gun at a slow, steady speed keeping the distance of the Spray Gun the same throughout the application. This will ensure perfect results. It is actually very easy. Practice, Practice, Practice. 8. It is best to hold the Hush Optimiser Spray Gun in a vertical position when spraying. If you want to change the direction of the mist pattern, rotate the position of the air cap rather than turning the Hush Optimiser Spray Gun on its side. Refer to the spray gun pattern diagram on page 7/8. 9. Always hold or store the Hush Optimiser Spray Gun in a vertical position. It is a good habit to use, when you are not spraying. 10. Do not over-tighten the solution flow screw (#22, page 7) as this will damage the end of the needle point. Tighten the screw until the needle cannot be pulled back. Once this point is reached there is no point in turning the solution slow screw anymore as this will only cause damage to the needle point. 9

10 5. Spraying HUSH HUSH SPRINTER endura You should now be ready to spray your client. Good quality results with your Hush Sprinter spray tanning system are a combination of careful preparation of your client, a proper spraying environment, a basic knowledge of the solution you will be using and how these solutions work with your Hush Sprinter spray tanning system. 1. You are now ready to begin spraying. 2. The ON/OFF Switch is located at the side of the Hush Sprinter Unit. Turn it on. You will hear a sound similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the Hush Sprinter Spray Gun. This is correct. Air will continually flow from the air cap of the Hush Sprinter Spray Gun as long as the Hush Sprinter Unit is running and the air hose is connected. 3. Your Hush Sprinter motor unit is set for the perfect atomisation of spray tan solution. 4. Open the Solution Flow Screw as described in item 4 and set the Pattern Adjustment Knob. 5. Set the mist pattern you wish to use by adjusting the air cap to the desired position. Refer to the spray gun pattern diagram on page 7/8. 6. Direct the Hush Optimiser Spray Gun to the area of the body that you want to start spraying. 7. Pull back on the trigger (#32, Diagram on page 7) and move the Hush Optimiser Spray Gun as noted in the diagram below. Do not wave the Spray Gun back and forth in front of your client by bending your wrist. Rather, keep your wrist straight and move your entire arm. Movement should be steady, even and deliberate, keeping your distance the same at all times. PROPER MISTING TECHNIQUE 10

11 6. Maintenance 1. Hush Sprinter Unit. HUSH HUSH SPRINTER endura a. There is minimal maintenance to perform on the Hush Sprinter unit. Make sure you keep the motor unit as far away from your spraying area as possible. b. Every night wipe over Hush Sprinter unit with a damp cloth. Please Note: Ensure no excess water is used as this will short circuit the unit. c. Please see maintenance cleaning video at: Education 2. Air Filter. a. Remove the air filter at the base of the unit and wash at the end of every week under hot soapy water. Ensure it is dry before replacing it. Replace the white filter when it can t be washed anymore. 3. Air Hose. a. Wipe the air hose daily with a damp cloth and store in a clean dry place. 4. Hush Optimiser Spray Gun - Daily Clean. a. It is important to clean your Hush Optimiser Spray Gun daily. b. At the end of the day or when the equipment will not be used any more, disconnect the Hush Optimiser Spray Gun from the air hose. c. Carefully unscrew the cup. If there is remaining solution, either close the cup with a lid, or pour the remaining solution into a proper storage container. d. Rinse the cup under hot running water until clean. e. Turn the gun upside down and allow hot running water to run into the plastic tube, pull back the trigger and allow the water to flow out of the nozzle. Continue until clear. f. Fill the cup about ¼ full with AIRBRUSH CLEANER. Reconnect the Hush Optimiser Spray Gun to Air Hose. Turn on the Hush Sprinter Unit. Direct the Hush Optimiser Spray Gun to a safe area and spray the AIRBRUSH CLEANER through the Hush Optimiser Spray Gun until the cup is empty and until the Spray becomes CLEAR. g. Turn off the Hush Sprinter Unit. Disconnect the Hush Optimiser Spray Gun. Unscrew the cup. h. Start to dismantle your Hush Optimiser Spray Gun. i. Unscrew and remove the Air Cap Ring (#1, Diagram on page 7). Rinse the threads under warm running water. Wipe, the threads and dry. Add a small amount of Spray lube or Vaseline to the threads. j. Reinstall the two pieces you just removed by reversing the removal procedure. Your Hush Optimiser Spray Gun should be ready for the next use. j. Please see Spray Gun maintenance cleaning video at: Education 11

12 6. Maintenance Cont d HUSH HUSH SPRINTER endura 5. Hush Optimiser Spray Gun - Weekly Clean. Perform the Daily procedure then continue: a. The Solution needle (#20, Diagram on page 6) To remove: Face the front of the gun away from you, turn the Solution flow screw anti clockwise until it comes out of the Spray Gun. Be careful when removing the solution flow Screw as there is a small spring (#21, Diagram on page 6) around the needle. Do not loose it. This is important to the operation of the Hush Optmiser Spray Gun. Set the spring aside and pull the trigger all the way back until you can grab the needle with your finger tips and pull it out from the back of the Hush Optimiser Spray Gun. Once removed, rinse under the hot running water, dip into AIRBRUSH CLEANER and dry. Add gun lubrication or vaseline to the needle. Simply rub a small amount of Spray Gun lube or vaseline around the needle shaft and spring. Later to reinstall repeat these steps in reverse. b. The solution nozzle (#2, Diagram on page 6) can be removed for additional cleaning as it is recommended to, the needle must first be removed to do this procedure. With an adjustable wrench or spanner that is supplied when you purchase the unit, place the tip of your adjustable wrench or spanner on the nut of the nozzle (whilst the gun is facing you) and twist anti clockwise. Be careful. Rinse under hot running water, take a cotton bud or the brush supplied and dip it into gun cleaner and clean inside the threads. DO NOT USE ANYTHING METAL as it will scratch the threads or nozzle and this will cause leaking. To reinstall repeat these steps in reverse. c. Please see Spray Gun maintenance cleaning video at: Education HVLP Gun/Airbrush Cleaner: Specially formulated to breakdown and remove spray tanning ingredients and residue from Airbrush/HVLP tips & nozzles. When using spray tan in your Hush Optimiser spray gun it can leave a build-up of residue that, overtime, can clog your Hush Optimiser spray gun tip and interfere with the effectiveness of your spray pattern. Solaire s Airbrush Cleaner is specifically developed to breakdown the residue left in your airbrush tip or spray gun nozzle. Spray Tan Gun Cleaner Available through our Office please call us! 12 *Excluded any parts that may be required to be replaced.

13 7. Troubleshooting HUSH HUSH SPRINTER endura Q. Hush Sprinter unit turned ON. Air blows out of Hush Optimiser Spray Gun? This is correct. Air blows constantly when Hush Sprinter unit is ON. Q. Hush Sprinter unit turned ON. Unit does not operate or blow air? Check that the unit is plugged in to proper electric source. Be sure there is power at the electric source. Check if the unit has been running. The overheat protector will be activated if the unit has reached 125ºC. Allow the unit to cool if overheating. Q. Hush Sprinter unit is turned ON the trigger is pulled back on Hush Optimiser Spray Gun but no solution comes out? Check that the cup is screwed firmly to Hush Optimiser Spray Gun. Check that there is no solution bubbling or leaking around the cup. Turn Hush Sprinter unit OFF. Unscrew cup. Be sure that Solution Tube (#39, Diagram on page 7) is connected and has not come loose. Turn Hush Sprinter unit OFF. Remove air cap ring (#1-1, Diagram on page 6) remove air cap (#1-2, Diagram on page 6) remove the needle (#20, Diagram on page 6) remove nozzle (#2, Diagram on page 6) with an adjustable wrench or spanner which is supplied at purchase. Rinse Solution Nozzle under running water and check for dried solution that may have blocked the hole. Reinstall Solution Nozzle, solution needle, air cap and air cap ring. Try spraying again. Q. Solution leaks in front of trigger? With an adjustable wrench or spanner tighten Solution Needle Packing Screw (#28, Diagram on page 6). Do not over tighten. This can cause Solution needle to stick and not spring back. Try spraying again. If leaking continues the Solution Needle Packing needs to be replaced. (Rare). Remove solution needle (#20, Diagram on page 6), then remove Solution Needle Packing Screw (#28, Diagram on page 6). Dry out the Solution Needle Packing s Replace. Reinstall Solution Needle Packing Screw and solution needle. Tighten all the way, and then back off slightly. (1/8 turn) Test the Hush Optimiser spray gun for leakage. Q. When Hush Sprinter unit is ON, Solution continues to spray from the Hush Optimiser Spray Gun without trigger being pulled? Immediately turn Hush Sprinter unit OFF. Disconnect Hush Optimiser spray gun from air hose. Slightly adjust (loosen) Solution Needle Packing Screw (#28, Diagram on page 6). Test to see if problem is resolved. Check to see that Needle Spring is installed. (#21, Diagram on page 6). Remove Solution Flow Screw (#22, Diagram on page 6). Look for Needle Spring around the back of the Solution Needle. If lost, order for replacement. Check Solution nozzle. Remove and clean following the spray gun weekly clean directions on page 12. Q. Solution leaks around the top of the cup. Make sure there is a gasket (#36, diagram on page 6) Make sure the cup is screwed firmly to the body of the Hush Optimiser Spray Gun. Make sure the threads around the cup are clean and the threads inside the cup top assembly are clean. Replace the cup top gasket. Pry out old gasket. Install new gasket. Test Hush Optimiser spray gun. 13

14 7. Hush Optimiser Spray Gun Problems HUSH HUSH SPRINTER endura 14

15 RECORD OF Hush Sprinter USE HUSH HUSH SPRINTER endura MODEL SERIAL# DATE PURCHASED DATE HOURS OF USE TOTAL HOURS 15

16 RECORD OF Hush Sprinter MAINTENANCE HUSH HUSH SPRINTER endura DATE MAINTENANCE PERFORMED 16

17 Solaire Warranty Card Solaire Pty ltd Name: Salon or Business Name: Address: Telephone Number: Mobile: address: Date of Purchase: Purchased from: Proof of Receipt with matching serial number is copied and attached? Yes No Model: Serial Number: I have read and understood the terms and conditions in the Solaire Warranty Card and I have completed the necessary requirements. Purchaser s Acknowledgement Signature: Date: / / A warranty is provided with this piece of equipment provided it is used in conjunction with manufactures instructions and THE WARRANTY CARD IS RETURNED within 14 days of receipt of purchase AND prior to use the purchaser acknowledges reading and fully understanding the Manufactures Instruction Manual. You must complete your spray tan gun maintenance and equipment care training module. If you fail to complete all three of the above YOU VOID your warranty. The most common cause of failure of any spray tan equipment is lack of cleaning, so take the time to make sure you look after your investment. Please ensure you read the instructions carefully and complete the spray tan gun maintenance and equipment care training module at You will need to register on the site prior to completing your training. The website is also full of a whole range of products and education to help you as the spray tan specialist ensure you deliver the most professional customer service and an award winning Solaire spray tan. Complete your contact details. Attach a copy of the original receipt showing the serial number. to: sales@solaire.com.au. Read the Manufactures Instruction Manual. Register at and complete the spray tan gun maintenance and equipment care training module. This is found in the education tab on the left hand side of the home page. Click on sunless education and watch the video.

18 Solaire will extend a warranty on equipment as provided by the Manufactures Instruction Manual of the goods. Solaire Pty Ltd warrants that products assembled by Solaire Pty Ltd shall be free from defects as it relates to Solaire Pty Ltd workmanship for a period as outlined in the Manufactures Instruction Manual for each respective piece of equipment from the date of purchase from Solaire Pty Ltd or its distributors or agents to the buyer. If during the warranty period, the goods should prove defective as determined by Solaire Pty Ltd or its authorized repairer, then the Solaire can, at their discretion, repair or replace the goods. In no event shall Solaire Pty Ltd, manufacturer of goods, their subsidiaries and affiliated companies, be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from negligence of seller. In addition, this warranty shall not apply to any goods or portions thereof which have been subjected to abuse, misuse and improper installation, maintenance or operation, electrical failure or abnormal conditions, and to goods which have been tampered with, altered, modified, repaired or reworked by anyone not approved by Solaire Pty Ltd. Solaire Pty Ltd warranty herein is in lieu of and excludes all other warranties of seller and the distributor of the goods and their subsidiaries and affiliated companies, whether expressly implied, statutory or otherwise created under applicable law including, but not limited to, the warranty of merchantability and the warranty of fitness for particular purpose or use. This Warranty does NOT include: misuse, damage, neglect, alterations, disassembled equipment or modifications, lack of maintenance, cleaning, water damage to electrical parts and INCORRECT VOLTAGE CONNECTION. Warranty Procedure: 1. sales@solaire.com.au to request a WARRANTY Claim Form. Fill in the WARRANTY claim form and it to: sales@solaire.com.au. Try to include as much detail as possible about the problem. 2. If at all possible we try to help you solve the problem and therefore you may be contacted regarding your claim either via phone or . If we are unable to solve the issue the equipment will need to be assessed and it will need to go to one of our Authorised repairers - we will issue you a claim number. 3. Once you have your claim number insert the number on Warranty Claim Form. 4. Ensure equipment is clean, dry and securely wrapped to prevent any leaking of fluid and well-padded and packaged to prevent damage to the equipment during shipping. 5. Send the form with the goods to the address on the WARRANTY CLAIM FORM. 6. Send a copy of the receipt from the original purchaser showing serial number, place of purchase, date of purchase. 7. You will be required to pre - pay all shipping charges. 8. Our Authorized repairer will attend to you claim promptly and contact you to discuss after they have assessed the claim.