INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER

Size: px
Start display at page:

Download "INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER"

Transcription

1 INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER Part No.: SW1250 PLEASE READ CARE AND SAFETY INSTRUCTIONS BEFORE USE

2 SPECIFICATIONS Part No.: SW1250 Input Voltage: 240V Frequency: 50Hz Rated Input Power: 250W Peak Input Power: 450W No Load Speed: 2850RPM Wheel Diameter: 150mm (6 ) x 20mm Wheel Grit: #36 (left) & #60 (right) Spindle Shaft Size: M12 x 1.75MM Power cord Length: 1.75M Net Weight: 7.5KG Warranty: 3 Years INCLUDES 1 x Swarts Tools Bench Grinder 1 x Clear safety guard 1 x Magnified safety guard 2 x Safety guard support (left & right) 2 x Clamping plate 1 x Flat work support 1 x Indented work support 2 x thumb screws Assembly Hardware

3 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don t use power tools in damp, wet or poorly lit locations. Don t expose your tool to rain. Keep the work area well lit. Don t use tools in the presence of flammable gasses or liquids. 3. KEEP CHILDREN AND BYSTANDERS AWAY. All children should be kept away from the work area. Don t let them handle machines, tools or extension cords. Visitors can be a distraction and are difficult to protect from injury. 4. GROUNDED TOOLS must be plugged into an outlet that itself is properly installed and grounded. Grounding provides a low-resistance path to carry electricity to ground away from the operator, should the tool malfunction electrically. Do not remove the grounding prong from the plug or alter the plug in any way. If in doubt as to whether the outlet is properly grounded according to code, check with a qualified electrician. 5. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces: pipes, radiators and refrigerator enclosures. When your body is grounded the risk of electric shock increases. When working wherever live electrical wires may be encountered, try to ascertain whether there is a danger of shock. 6. DO NOT ABUSE THE CORD. Never carry power tool by the cord or pull on the cord to unplug it. Protect the cord from potential sources of damage: heat, oil and solvents, sharp edges or moving parts. Replace damaged cords immediately. 7. WHEN WORKING OUTDOORS, USE AN OUTDOOR-RATED EXTENSION CORD. 8. DO NOT EXPOSE ELECTRICAL POWER TOOLS TO MOISTURE. Rain or wet conditions can cause water to enter the tool and lead to electric shock. 9. ENSURE THE EXTENSION CORD YOU USE IS OF SUFFICIENT GAUGE FOR ITS LENGTH. 10. STORE IDLE EQUIPMENT. Store equipment in a dry area to inhibit rust. Equipment should also be stored in a high location or locked up to keep out of reach of children. 11. DON T FORCE THE TOOL. It will do the job better and more safely at the rate for which it was intended. 12. USE THE RIGHT TOOL. Don t force a small tool or attachment to do the work of a larger industrial tool. Don t use a tool for a purpose for which it was not intended. 13. DRESS PROPERLY. Don t wear loose clothing or jewellery; they can be caught in moving parts. Protective, nonelectrical conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair and keep it from harm. 14. USE EYE PROTECTION. Use a full-face mask if the work you re doing produces metal filings, dust or wood chips. Goggles are acceptable in other situations. Wear a clean dust mask if the work involves creating a lot of fine or course dust. 15. SECURE WORK. Always ensure when using this tool, that the workpiece is held firmly by either your hands or lockable pliers. This is to ensure that you have full control over the workpiece at all times and it does not get caught in the grinding wheels. 16. DON T OVERREACH. Keep proper footing and balance at all times. Do not reach over or across machines that are running. INSTRUCTION BOOKLET 1

4 17. DON T FORCE THE TOOL. It will do the job better and more safely at the rate for which it was intended. 18. USE THE RIGHT TOOL. Don t force a small tool or attachment to do the work of a larger industrial tool. Don t use a tool for a purpose for which it was not intended. 19. DRESS PROPERLY. Don t wear loose clothing or jewellery; they can be caught in moving parts. Protective, nonelectrical conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair and keep it from harm. 20. USE EYE PROTECTION. Use a full-face mask if the work you re doing produces metal filings, dust or wood chips. Goggles are acceptable in other situations. Wear a clean dust mask if the work involves creating a lot of fine or course dust. 21. SECURE WORK. Always ensure when using this tool, that the workpiece is held firmly by either your hands or lockable pliers. This is to ensure that you have full control over the workpiece at all times and it does not get caught in the grinding wheels. 22. DON T OVERREACH. Keep proper footing and balance at all times. Do not reach over or across machines that are running. 23. MAINTAIN TOOLS WITH CARE. Keep grinding wheels dressed and clean for better and safer performance. Follow instructions for lubricating and changing accessories. For safe performance keep tool dry, clean and free from oil and grease. 24. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position before plugging in. 25. ALWAYS CHECK AND MAKE SURE TO REMOVE ANY ADJUSTING KEYS OR WRENCHES before turning the tool on. Left attached, these parts can fly off a moving part and result in personal injury. 26. DO NOT USE THE TOOL IF IT CANNOT BE SWITCHED ON OR OFF. Have your tool repaired before using it. 27. DISCONNECT THE PLUG prior to MAKING ADJUSTMENTS. Changing attachments or accessories can be dangerous if the tool could accidentally start. 28. STAY ALERT. Watch what you are doing and use common sense. Don t operate any tool when you are tired. 29. CHECK FOR DAMAGED PARTS. Before using this tool, any part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mountings and other conditions that may affect its operation. Inspect screws and tighten any that are loose. Any part that is damaged should be properly repaired or replaced by an authorised service centre unless otherwise indicated elsewhere in the instruction manual. Make sure any defective switches are replaced by an authorised service centre. 30. REPLACEMENT PARTS. When servicing, use only identical replacement parts. 31. SERVICE AND REPAIRS should be made by qualified repair technicians at an authorised repair centre. Improperly repaired tools could cause serious shock or injury and may result in a void of the warranty. 2 INSTRUCTION BOOKLET

5 SAFETY PRECAUTIONS FOR THIS BENCH GRINDER 1. Make sure the grinding wheels are securely mounted as described in the assembly instructions before connecting the tool to a power supply. Do not tighten the wheels excessively, as this may cause the wheels to crack. 2. Check wheels for fissures and cracks prior to use. 3. Use only cut-off wheels rated for 2850rpm or greater. Always store the wheels in a dry place with little temperature variation. 4. Always ease the workpiece agaisnt the grinding wheels when commencing work. A harsh impact can cause damage to both the workpiece and the machine. 5. Always allow the machine to reach full speed prior to commencing work. 6. Always use the material support when grinding. 7. Only ever grind one object at time. 8. Only use approved Swarts Tools attachments on this tool. Failure to do so may result in voidng of the warranty. 9. Ensure all components of the machine (i.e. the work support or spark guard) are always set at a safe distance from the grinding wheels to prevent them from ever coming into contact. INSTRUCTION BOOKLET 3

6 FUNCTION DESCRIPTION 1. Top Spark Guard 2. Clear Safety Guard 3. Clamping Plate 4. Safety Guard Support 5. Magnified Safety Guard 6. Indented Work Support 7. Thumb Screw 8. ON/OFF Switch 9. Flat Work Support 10. Wheel Guard Locking Screws 11. Wheel Guard INSTRUCTION BOOKLET

7 BENCH GRINDER ASSEMBLY Warning: do not connect the grinder to a power source until assembly is complete. Failure to comply could result in accidental starting and possible serious injury Use a Phillips head screwdriver and the 7mm long bolts to attach the top spark guard plate (1) to the inside of the wheel guard, ensuring that you screw it in to the first hole. Repeat for the other side. Spin the wheel with your fingers to make sure that the guard will not come into contact with the wheel when turned on. See picture. 2. Attach the safety guard supports (4) to the remaining hole on the inside of the wheel guard. Use the 15mm bolts and the clamping plate (3) to hold them in place at just finger tight. Ensure they are attached as shown in the picture. 3. Attach the standard (clear) safety guard (2) to the left hand side safety guard support (4) by sliding it on the end. Do not fully tighten it yet Attach the magnified safety guard (5) to the right hand side safety guard support (4) by sliding it on the end. The magnified safety guard (5) should be placed over the fine wheel as the magnification is used for sharpening drill bits. 3 5 INSTRUCTION BOOKLET 5

8 5. Fit the spring washer and then the flat washer onto the thumb screw knobs (7). 6. Position the flat work support (9) over the locating pin on the course wheel side. Screw in the thumb screw (7). Ensure that once tightened, the work support (9) does not come into contact with the wheel. 7. Position the indented work support (6) over the locating pin on the fine wheel side.screw in the thumb screw knob (7). Ensure that once tightened, the work support (6) does not come into contact with the wheel. It is imperative that you attach the correct work support (6) to the correct side, as the work support with the channel in it is used for sharpening drill bits which require a finer wheel for an effective result. 8. Adjust the safety guards and safety guard clamp s (3) position to a suitable location for your desired job. You must place the guards (2 & 5) in a position so that it is between your face and the wheel to protect you from sparks and debris. Once your desired position is obtained, tighten the 15mm bolts over the clamps (3) as well as the 10mm nut on the rear of the guards. Be careful not to overtighten these, as it may cause the guards to crack or shatter Wipe clean the safety guards with a clean, dry cloth and glass cleaner if they have become dirty during set up or during use. 10. Carry out a test spin of the weels with your hands prior to plugging in and turning on the machine to ensure that nothing will touch the wheels. 6 INSTRUCTION BOOKLET

9 GRINDER WHEEL REMOVAL AND REPLACEMENT 1. Switch off and unplug the bench grinder. 2. Loosen the 3 locking screws (10) on the outer side of the wheel guard (be sure to just loosen & not remove them completely). 3. Twist the wheel guard (11) until the screws are in line with the large hole. 4. Remove the guard (11) - the grinding wheel will now be exposed. 5. Use a thick rag over your hand to hold the opposing wheel in place. Meanwhile, use an 18mm spanner counter-clockwise to remove the wheel nut. Be sure your hand does not get jammed between the wheel and the plate. 6. Remove the outer flange 7. Remove the current wheel. Inspect the inner flange for debris prior to installing the new wheel. 8. Place the new wheel onto the inner flange and be sure to inspect the outer flange for debris before placing it back onto the machine. 9. Reinstall the nut and turn the clockwise to tighten. Ensure that you do not over-tighten the nut. 10. Place the wheel guard (11) back on the tool and tighten the wheel guard screws (10) in place. Once you have completed this process, spin the new wheel with your hand to ensure that the wheel is secured properly, free from damage and well balanced. Note. If you have any questions regarding the set up of this tool please do not hesitate to contact us on (02) We are always happy to help. INSTRUCTION BOOKLET 7

10 8 INSTRUCTION BOOKLET

11 WARRANTY The product is warranted to be free from defects in materials and workmanship under normal use and service for a period of 36 months from the date of sale. This warranty covers defective parts and workmanship provided that the product is shipped pre-paid to the seller within 36 months of purchase of goods. This warranty is limited to the repair or replacement (at the manufacturers discretion) of parts and shipping prepaid to the original despatch destination. We regret that no liability can be accepted for consequential or special damages of any kind howsoever arising in connection with products supplied by the seller. This warranty is in lieu of all other warranties expressed or implied. No representative is authorised to assume for the seller any other liability in connection with the seller s products.

12 PLEASE READ CARE AND SAFETY INSTRCTIONS BEFORE USE

18 GAUGE ELECTRIC METAL SHEAR

18 GAUGE ELECTRIC METAL SHEAR 241-9895 18 GAUGE ELECTRIC METAL SHEAR Operator s Manual SAVE THIS MANUAL You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in

More information

ATBG280/6 Bench Grinder Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size

ATBG280/6 Bench Grinder Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size SPECIFICATIONS Model Number : ATBG280/6 Nominal Voltage Power Consumption No load speed Wheel size Weight 230Volt 50Hz 280 Watts 2880

More information

Operating Manual 6 Industrial Bench Grinder ATBG280/

Operating Manual 6 Industrial Bench Grinder ATBG280/ Operating Manual 6 Industrial Bench Grinder ATBG280/6 804531 40 Year Australian Heritage The reputable name in bench grinders for 40 years Protect yourself and others by observing all safety information,

More information

GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING DISC GRINDER

GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING DISC GRINDER GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

Angle Grinder MODEL 9553B MODEL 9555B

Angle Grinder MODEL 9553B MODEL 9555B ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR

More information

Quick Set Dovetail Jig

Quick Set Dovetail Jig Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT

More information

Instructions for Stone Cutting Machine

Instructions for Stone Cutting Machine Technical data Kg. Instructions for Stone Cutting Machine SCM600 3HP 2800rpm IP55 SCM800 3HP 2800rpm IP55 SCM1000 2800rpm IP55 SCM1200 2800rpm IP55 L=600 B=85(165) L=800 B=85(175) 500x510 0 or 45 600lt/h

More information

Sander. Finishing INSTRUCTION MANUAL. MODEL BO4550 MODEL BO45502 Without dust bag and punch plate DOUBLE INSULATION SPEC IF1 CAT1 ONS.

Sander. Finishing INSTRUCTION MANUAL. MODEL BO4550 MODEL BO45502 Without dust bag and punch plate DOUBLE INSULATION SPEC IF1 CAT1 ONS. Finishing INSTRUCTION MANUAL Sander MODEL BO4550 MODEL BO4550 Without dust bag and punch plate DOUBLE INSULATION SPEC IF CAT ONS Pad size No load speed lopml Dimensions (L x W x H) Net weight mmxloomm

More information

Electric Chainsaw Sharpener

Electric Chainsaw Sharpener FPP CHAINSS Electric Chainsaw Sharpener Instruction Manual For your own safety, please ensure you have read these instructions before use and have fully understood all the safety guidelines. Specifications

More information

PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE

PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE 92778 1 GENERAL SAFETY INFORMATION For your safety, please read these instructions carefully before use and keep them in the

More information

18 PIECE HOLE SAW SET

18 PIECE HOLE SAW SET 18 PIECE HOLE SAW SET 94665 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,

More information

GENERAL OPERATIONAL PRECAUTIONS

GENERAL OPERATIONAL PRECAUTIONS GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

Power Planer 1900B/N1900B/1902

Power Planer 1900B/N1900B/1902 Power Planer 1900B N1900B 1902 SPECIFICATIONS Model 1900B/N1900B/1902 Planing width... 82 mm Planing depth... 1 mm Shiplapping depth... 9 mm No load speed (min -1 )...16,000 Overall length... 290 mm Net

More information

ROTARY HAMMER OWNER'S MANUAL

ROTARY HAMMER OWNER'S MANUAL ROTARY HAMMER OWNER'S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal

More information

VARIABLE SPEED WOOD LATHE

VARIABLE SPEED WOOD LATHE MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02

More information

Cut-Off Machine Model CC 14SE

Cut-Off Machine Model CC 14SE Cut-Off Machine Model CC 14SE Handling instructions NOTE: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended

More information

GENERAL OPERATIONAL PRECAUTIONS

GENERAL OPERATIONAL PRECAUTIONS GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE

GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

Circular Saw MODEL MT581. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Circular Saw MODEL MT581. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH Circular Saw MODEL MT58 005337 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

12 Slip Roll. Model Assembly & Operating Instructions

12 Slip Roll. Model Assembly & Operating Instructions 12 Slip Roll Model 36698 Assembly & Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product

More information

30 Bending Brake. Model Assembly and Operating Instructions. Distributed exclusively by Harbor Freight Tools.

30 Bending Brake. Model Assembly and Operating Instructions. Distributed exclusively by Harbor Freight Tools. 30 Bending Brake Model 41311 Assembly and Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1999 by Harbor Freight Tools. All

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Shear Wrench 6922NB DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Shear Wrench 6922NB DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Shear Wrench 69NB 00498 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 69NB Bolt size M6, M0, M

More information

Drill INSTRUCTION MANUAL. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE 1 REFERENCE.

Drill INSTRUCTION MANUAL. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE 1 REFERENCE. ENGLISH (Original instructions) INSTRUCTION MANUAL Drill 6411 6412 6413 007894 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE

More information

Impact Wrench. 19 mm (3/4 ) MODEL 6906

Impact Wrench. 19 mm (3/4 ) MODEL 6906 Impact Wrench 9 mm (3/4 ) MODEL 6906 002290 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill DS4012 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill DS4012 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Drill DS402 05402 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DS402 Capacities Steel 3 mm Wood

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Curved Planer 1002BA DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Curved Planer 1002BA DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Curved Planer 00BA 0059 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 00BA Planing width 0 mm Planing

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Drill 64 642 643 007894 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 64 642 643 Capacities Steel

More information

HAND HELD SAW W MILL

HAND HELD SAW W MILL HAND HELD SAW W MILL 92247 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All

More information

Instruction Manual. Manual de instrucciones. Guide d utilisation ET PMET Rev 808

Instruction Manual. Manual de instrucciones. Guide d utilisation ET PMET Rev 808 Instruction Manual Manual de instrucciones Guide d utilisation ET2025 PMET2025-8 Rev 808 www.arrowfastener.com GENERAL SAFETY RULES WARNING! Read all instructions. Failure to follow all instructions listed

More information

GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

SAFETY AND OPERATING MANUAL. Hedge Trimmer WG205E WG206E WG207E WG208E

SAFETY AND OPERATING MANUAL. Hedge Trimmer WG205E WG206E WG207E WG208E SAFETY AND OPERATING MANUAL 2 PRODUCT SAFETY GENERAL Power Tool Safety Warnings WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or

More information

Impact Wrench MODEL TW1000. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Impact Wrench MODEL TW1000. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH Impact Wrench MODEL TW000 00605 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill MT600 MT601 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill MT600 MT601 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Drill MT600 MT60 003635 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MT600 MT60 Capacities Steel

More information

ROUND BENDING MACHINE Model: RBM30

ROUND BENDING MACHINE Model: RBM30 ROUND BENDING MACHINE Model: RBM30 Operation Manual SAVE THIS MANUAL:You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts

More information

Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y

Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire

More information

Finger Jointer. Operating and Safety Instructions FJA300

Finger Jointer.  Operating and Safety Instructions FJA300 Finger Jointer FJA300 Operating and Safety Instructions www.tritontools.com Thank you for purchasing this Triton tool. These instructions contain information necessary for safe and effective operation

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL BladeRunner X2 WX572 9 10 8 11 5 7 12 6 20 1 2 4 3 14 13 15 A2 A1 17 18 B2 B1 1 2 1 2 19 B3 3 4 2 C 1 D1 D1 C 2 1 E1 D2 1 2 E2 1 2 F G1 G1 F OFF ON G2 G3 H1 H2 I1 I2 I1 I2 J

More information

12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)

12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max) 1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22

More information

VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL

VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4

More information

6 BENCH GRINDER. Model ASSEMBLY AND OPERATING INSTRUCTIONS

6 BENCH GRINDER. Model ASSEMBLY AND OPERATING INSTRUCTIONS 6 BENCH GRINDER Model 90003 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools.

More information

INSTRUCTION MANUAL. 125 mm (5 ) MODEL 9005B 125 mm (5 ) MODEL 9005BZ. DOUBLE I N S U LATlO N SPEC IF I CAT I 0 N S

INSTRUCTION MANUAL. 125 mm (5 ) MODEL 9005B 125 mm (5 ) MODEL 9005BZ. DOUBLE I N S U LATlO N SPEC IF I CAT I 0 N S 25 mm (5 ) MODEL 9005B 25 mm (5 ) MODEL 9005BZ INSTRUCTION MANUAL DOUBLE I N S U LATlO N SPEC IF I CAT I 0 N S No load speed (RPM) 0,000lmin. AMPS Overall Net Power Spindle (5 V) length weight supply cord

More information

2-Speed Hammer Drill HP2000 HP2020

2-Speed Hammer Drill HP2000 HP2020 2-Speed Hammer Drill HP2000 HP2020 SPECIFICATIONS Model HP2000 HP2020 Speed High Low High Low Capacities Concrete 20 mm 20 mm Steel 6.5 mm 13 mm 6.5 mm 13 mm No load speed (min 1 ) 0 2,300 0 900 2,300

More information

ASSEMBLY AND OPERATING INSTRUCTIONS

ASSEMBLY AND OPERATING INSTRUCTIONS Work Bench 91835 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights reserved.

More information

ITEM Pipe Thread Kit (10 Piece Set - 7 Dies) Assembly and Operating Instructions

ITEM Pipe Thread Kit (10 Piece Set - 7 Dies) Assembly and Operating Instructions ITEM 94098 Pipe Thread Kit (10 Piece Set - 7 Dies) Assembly and Operating Instructions 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 2006 by Harbor Freight Tools. All rights reserved. No portion

More information

Dust Collector. Model No: DC2200 (FM300S)

Dust Collector. Model No: DC2200 (FM300S) Dust Collector Model No: DC2200 (FM300S) GENERAL SAFETY INSTRUCTIONS Before attempting to operate this machine, it is important that you read, understand and follow these instructions very carefully. They

More information

12 SHEAR, PRESS BRAKE &SLIPROLL

12 SHEAR, PRESS BRAKE &SLIPROLL 12 SHEAR, PRESS BRAKE &SLIPROLL OPERATION MANUAL SPECIFICATION Cpacity: Roller : Die set sizes: Weight: 1mm thick (20gauge), 305 mm (12 ) width 38mm(1-1/2 ) 101.6mm(4 ), 76.2mm(3 ), 50.8mm (x2)[2 9x2]],

More information

lmnact Wrench INSTRUCTION MANUAL 19 mm (3/4") MODEL 6906 SPECIFICATIONS 'ION --I- - -

lmnact Wrench INSTRUCTION MANUAL 19 mm (3/4) MODEL 6906 SPECIFICATIONS 'ION --I- - - lmnact Wrench --I- - - 19 mm (3/4") MODEL 6906 INSTRUCTION MANUAL 'ION SPECIFICATIONS Capacities Impacts No load Tightening 1 Square drive I m%ite I speed (RPMI I torque 1 Bolt size 16 mm - 22 mm (518''

More information

BB Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

BB Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. BB07552 5 Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

ATD TON BAR TYPE PULLER/BEARING SEPARATOR SET

ATD TON BAR TYPE PULLER/BEARING SEPARATOR SET ATD-3056 5-TON BAR TYPE PULLER/BEARING SEPARATOR SET Made in China to ATD Inc. Specifications WARNING: When using this tool, basic safety precautions should always be followed to reduce the risk of personal

More information

PLATE JOINER 4 INCH. ASSEMBLY and OPERATING INSTRUCTIONS. Distributed Exclusively by Harbor Freight Tools

PLATE JOINER 4 INCH. ASSEMBLY and OPERATING INSTRUCTIONS. Distributed Exclusively by Harbor Freight Tools PLATE JOINER 4 INCH 38437 ASSEMBLY and OPERATING INSTRUCTIONS Distributed Exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1998 by Harbor Freight Tools. All rights

More information

Item# " VARIABLE SPEED BENCH GRINDER USER'S MANUAL

Item#  VARIABLE SPEED BENCH GRINDER USER'S MANUAL Power Tools Item# 33309 3" VARIABLE SPEED BENCH GRINDER USER'S MANUAL Read carefully and understand RULES FOR SAFE OPERATION and instructions before operating. Failure to follow the safety rules and other

More information

8 Buffer. Set up and Operating Instructions. (Buffing Wheels Not Included) Distributed exclusively by Harbor Freight Tools.

8 Buffer. Set up and Operating Instructions. (Buffing Wheels Not Included) Distributed exclusively by Harbor Freight Tools. 8 Buffer 40668 Set up and Operating Instructions (Buffing Wheels Not Included) Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com

More information

Grinding drill machine OPERATION MANUAL - 1 -

Grinding drill machine OPERATION MANUAL - 1 - Grinding drill machine OPERATION MANUAL - 1 - Index: I. Safety Notification P.4 II. Machine Devices Introduction P.9 III. Machine Installation Instruction P.11 IV. Standard Operational Steps P.13 V. Replacement

More information

MODEL W1.0X305A(12 ) MODEL W1.0X610A(24 ) HAND BENDING BRAKE ASSEMBLY&OPERATING INSTRUCTION

MODEL W1.0X305A(12 ) MODEL W1.0X610A(24 ) HAND BENDING BRAKE ASSEMBLY&OPERATING INSTRUCTION MODEL W1.0X305A(12 ) MODEL W1.0X610A(24 ) HAND BENDING BRAKE ASSEMBLY&OPERATING INSTRUCTION 1 SAVE THIS MANUAL You will need the manual for the safety warning and precautions, assembly instructions, operating

More information

High Speed Drill MODEL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

High Speed Drill MODEL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH High Speed Drill MODEL 6501 003002 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

RIGHT ANGLE DRILL ATTACHMENT WITH 3/8 KEYLESS CHUCK

RIGHT ANGLE DRILL ATTACHMENT WITH 3/8 KEYLESS CHUCK RIGHT ANGLE DRILL ATTACHMENT WITH 3/8 KEYLESS CHUCK 96996 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product

More information

Electronic Polisher 180 mm (7") MODEL PV7001 C

Electronic Polisher 180 mm (7) MODEL PV7001 C Electronic Polisher 180 mm (7") MODEL PV7001 C INSTRUCTION MANUAL No load speed (RPM) 600-2,00O/min Overall length Net weight Spindle thread 210 mm (8-1/4") 2 0 kg (4 4 Ibs) 518" GENERAL SAFETY RULES USAOO1-l

More information

Drill 13 mm (1/2 ) MODEL 6302H

Drill 13 mm (1/2 ) MODEL 6302H Drill 3 mm (/2 ) MODEL 6302H 3 mm (/2 ) MODEL 6303H INSTRUCTION MANUAL Variable speed / Reversing Variable speed / Reversing DOUBLE INSU LATlO N SPECIFICATIONS Steel Wood (RPM) 6302H I 3 mm (/2 ) I 36

More information

BENCH GRINDER OWNER S MANUAL

BENCH GRINDER OWNER S MANUAL BENCH GRINDER OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result

More information

Nibbler MODEL JN1601. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Nibbler MODEL JN1601. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH Nibbler MODEL JN60 00477 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS

More information

4.0MM METAL CUTTING NIBBLER

4.0MM METAL CUTTING NIBBLER 596702 4.0MM METAL CUTTING NIBBLER Read through carefully and understand these instructions before use N3570 SAFETY INSTRUCTIONS PLEASE READ & UNDERSTAND THESE INSTRUCTIONS! STORE THESE INSTRUCTIONS IN

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Hammer Drill HP1630 HP1631 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Hammer Drill HP1630 HP1631 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Hammer Drill HP630 HP63 008892 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model HP630 HP63 Concrete

More information

Handling instructions

Handling instructions Hand Shear Model CE 16SA Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that

More information

10" Wet Tile Cutting Saw

10 Wet Tile Cutting Saw 8035735 10" Wet Tile Cutting Saw Owner s Manual Read and understand all instructions before operation. Keep this manual for future reference pg. 2 SPECIFICATIONS ITEM DESCRIPTION Overall Dimensions (saw

More information

Cut-Off Machine CC 14SF. Read through carefully and understand these instructions before use. Handling instructions

Cut-Off Machine CC 14SF. Read through carefully and understand these instructions before use. Handling instructions Cut-Off Machine CC 14SF Read through carefully and understand these instructions before use. Handling instructions GENERAL OPERATIONAL PRES WARNING! When using electric tools, basic safety precautions

More information

Jigsaw Kit. Operating and Safety Instructions AJA300

Jigsaw Kit.  Operating and Safety Instructions AJA300 Jigsaw Kit AJA300 Operating and Safety Instructions www.tritontools.com Thank you for purchasing this Triton tool. These instructions contain information necessary for safe and effective operation of this

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Hammer Drill MHP161 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Hammer Drill MHP161 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Hammer Drill MHP6 0088 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MHP6 Concrete 6 mm Capacities

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL Impact drill WX317 WX318 1 3 2 8 7 6 5 4 A1 A2 B C1 2 1 3 3 1 D C2 5 4 E F 2 E F 1 G 4 2 H 1. Keyless Chuck 2. Depth gauge 3. Drill/hammer drill function selector 4. Switch

More information

8" Bench Grinder OWNER S MANUAL SAFETY GLASSES C US E LISTED TABLE OF CONTENTS SPECIFICATIONS PLEASE WEAR. Stock Number W50058

8 Bench Grinder OWNER S MANUAL SAFETY GLASSES C US E LISTED TABLE OF CONTENTS SPECIFICATIONS PLEASE WEAR. Stock Number W50058 8" Bench Grinder Stock Number W50058 OWNER S MANUAL C US E154499 LISTED TABLE OF CONTENTS Safety Instructions...2 Bench Grinder Safety...3 Electrical Requirements...3 Replacement Parts List...4 Bench Grinder

More information

Impact Wrench MODEL 6905B MODEL 6906

Impact Wrench MODEL 6905B MODEL 6906 ENGLISH Impact Wrench MODEL 6905B MODEL 6906 005305 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR

More information

Belt Sander INSTRUCTION MANUAL MODEL S PECl FI CAT1 0 N S

Belt Sander INSTRUCTION MANUAL MODEL S PECl FI CAT1 0 N S 3,80 Belt Sander MODEL 903 INSTRUCTION MANUAL S PECl FI CAT 0 N S Belt size Belt speed Overall length Net weight 30 mm x 533 mm (.36" x ") 00 m -,000 m (656 ft. ~ ft,)/m~n. 380 mm (4-3/3"). kg (4.6 Ibs)

More information

SAFETY AND OPERATING MANUAL. 750W/13mm IMPACT DRILL JM750ID

SAFETY AND OPERATING MANUAL. 750W/13mm IMPACT DRILL JM750ID SAFETY AND OPERATING MANUAL 750W/13mm IMPACT DRILL JM750ID GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

More information

SMALL GAUGE NIBBLER ASSEMBLY & OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web Site at

SMALL GAUGE NIBBLER ASSEMBLY & OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web Site at SMALL GAUGE NIBBLER 91739 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights reserved.

More information

D R I L L - G R I N D E R S BL 13D-2

D R I L L - G R I N D E R S BL 13D-2 D R I L L - G R I N D E R S BL 13D-2 2 Table of contents 1. General safety rules for all machines 3 2. Additional safety rules 4 3. Features 4 4. Specification 4 5. Operation 4 5.1 Assemble the fixture

More information

Curved Planer INSTRUCTION MANUAL. 82 mm (3-1/4") MODEL mm 1118"l 12, mm 1,14~1/2"1 6.0 kg lbsl. 82 mm 13~114") IRPMI

Curved Planer INSTRUCTION MANUAL. 82 mm (3-1/4) MODEL mm 1118l 12, mm 1,14~1/21 6.0 kg lbsl. 82 mm 13~114) IRPMI Curved Planer 8 mm (3-/4") MODEL 00 INSTRUCTION MANUAL Planing width 8 mm 3~4") Planing depth No load speed Overall length Net weight IRPMI 3 mm 8"l,000 370 mm,4~/" 6.0 kg 3. lbsl IMPORTANT SAFETY INSTRUCTIONS

More information

18V CORDLESS STAPLER/NAILER

18V CORDLESS STAPLER/NAILER 18V CORDLESS STAPLER/NAILER MODEL NO: CONSN18LIC PART NO: 6487058 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0717 ISS2 2 INTRODUCTION Thank you for purchasing this CLARKE product. Before

More information

PS /8 Inch Electric Drill Assembly & Operating Instructions

PS /8 Inch Electric Drill Assembly & Operating Instructions PS07216 3/8 Inch Electric Drill Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

1/4 Sheet Palm Sander

1/4 Sheet Palm Sander OWNER S MANUAL Model Number: PS160CA-3 1/4 Sheet Palm Sander TM Registration Card Inside CAUTION! To reduce the risk of fire, electric shock and personal injury, read and understand the owner s manual

More information

Rotary Hammer Drill 3-Wire Grounded Construction. Printed: Doc-Nr: PUB / / 000 / 00

Rotary Hammer Drill 3-Wire Grounded Construction. Printed: Doc-Nr: PUB / / 000 / 00 *312483* 312483 Operating instructions TE 35 Rotary Hammer Drill 3-Wire Grounded Construction General safety rules 1. WARNING! Read and understand all instructions. Failure to follow all instructions listed

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Straight Shear JS1660 JS1670 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Straight Shear JS1660 JS1670 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Straight Shear JS660 JS670 004666 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model JS660 JS670 Steel

More information

KR703-XE KR704-XE KR705-XE KR753-XE KR754-XE KR755-XE Australia New Zealand

KR703-XE KR704-XE KR705-XE KR753-XE KR754-XE KR755-XE Australia New Zealand 6 5 4 www.blackanddecker.com.au 3 7 2 1 8 KR703-XE KR704-XE KR705-XE KR753-XE KR754-XE KR755-XE Australia New Zealand 7 8 A 12 13 10 9 10 B C 11 7 8 D E 2 Intended use Your Black & Decker hammer drill

More information

Angle Drill MODEL DA3000R MODEL DA3000V

Angle Drill MODEL DA3000R MODEL DA3000V ENGLISH Angle Drill MODEL DA3000R MODEL DA3000V 003004 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR

More information

DRILL BIT SHARPENER MODEL NO: CBS43 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0710

DRILL BIT SHARPENER MODEL NO: CBS43 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0710 DRILL BIT SHARPENER MODEL NO: CBS43 PART NO: 6480232 OPERATION & MAINTENANCE INSTRUCTIONS LS0710 INTRODUCTION Thank you for purchasing this CLARKE drill bit sharpener. Before attempting to use this product,

More information

154570/220 5/17/02 1:41 PM Page 3. Instruction Manual Variable Speed Orbital Action Jig Saw

154570/220 5/17/02 1:41 PM Page 3. Instruction Manual Variable Speed Orbital Action Jig Saw 154570/220 5/17/02 1:41 PM Page 3 Instruction Manual 3157-220 Variable Speed Orbital Action Jig Saw 154570/220 5/17/02 1:41 PM Page 4 Getting the most out of your tool. Please take time to read this manual

More information

Impact Wrench WR 22SA HANDLING INSTRUCTIONS. Read through carefully and understand these instructions before use.

Impact Wrench WR 22SA HANDLING INSTRUCTIONS. Read through carefully and understand these instructions before use. Impact Wrench WR 22SA HANDLING INSTRUCTIONS Read through carefully and understand these instructions before use. 1 1 2 2 3 4 5 3 6 7 8 9 5 3 4 kg-m 80 N m 800 M22 70 (F 10T) 0 C 70 700 60 50 600 500 40

More information

MULTI-PURPOSE SAW MODEL NO. OZMPS500A OPERATING INSTRUCTIONS

MULTI-PURPOSE SAW MODEL NO. OZMPS500A OPERATING INSTRUCTIONS MULTI-PURPOSE SAW 500watt MODEL NO. OZMPS500A OPERATING INSTRUCTIONS To view our entire range visit www.ozito.com.au SPECIFICATIONS - MODEL NO. OZMPS500A Motor: Input: No load speed: Length of stroke:

More information

Recipro Saw MODEL JR3020. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Recipro Saw MODEL JR3020. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH Recipro Saw MODEL JR3020 002479 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

OPERATION & MAINTENANCE

OPERATION & MAINTENANCE DOUBLE HEADED METAL NIBBLER MODEL NO: DHC-2 PART NO: 6500233 OPERATION & MAINTENANCE INSTRUCTIONS LS0609 INTRODUCTION Thank you for purchasing this CLARKE Double Headed Metal Nibbler. Before attempting

More information

Subject to change. USERS MANUAL Art.nr. PRM6006 PBF-1050N

Subject to change. USERS MANUAL Art.nr. PRM6006 PBF-1050N UK Subject to change UK USERS MANUAL Art.nr. PRM6006 PBF-1050N 0406-14 EXPLODED VIEW Fig. D Fig. A Fig. E Fig. B Fig. F Fig. C Fig. G 2 Powercraft Powercraft 11 SPARE PARTS LIST PBF-1050N REF NR DESCRIPTION

More information

INSTRUCTION MANUAL TRAXX 5418 Electric Stapler V AC Hz IMPORTANT SAFETY INSTRUCTION

INSTRUCTION MANUAL TRAXX 5418 Electric Stapler V AC Hz IMPORTANT SAFETY INSTRUCTION INSTRUCTION MANUAL TRAXX 5418 Electric Stapler 110-120 V AC 50-60 Hz IMPORTANT SAFETY INSTRUCTION WARNING: when using Electric Tools, basic safety precautions should always be followed to reduce the risk

More information

INSTRUCTION MANUAL MODEL JN1601 SPEC I FI CAT1 0 N S DOUBLE INSULATION

INSTRUCTION MANUAL MODEL JN1601 SPEC I FI CAT1 0 N S DOUBLE INSULATION MODEL JN60 INSTRUCTION MANUAL DOUBLE INSULATION SPEC I FI CAT 0 N S Max. cutting capacities Mild steel Stainless Aluminum.6 mm. mm.5 mm (lil6") 3/64") (33") Min. cutting radius I I I Strokes Overall Net

More information

Hammer Drill MODEL HP1500 MODEL HP1501 MODEL HP1510

Hammer Drill MODEL HP1500 MODEL HP1501 MODEL HP1510 ENGLISH Hammer Drill MODEL HP500 MODEL HP50 MODEL HP50 002395 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill MDP303 MDP304 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Drill MDP303 MDP304 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Drill MDP303 MDP304 0876 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MDP303 MDP304 Capacities

More information

WARNING! Read and understand the entire instruction manual before attempting set-up or operation of this machine!

WARNING! Read and understand the entire instruction manual before attempting set-up or operation of this machine! ! WARNING! Read and understand the entire instruction manual before attempting set-up or operation of this machine! 1. This machine is designed and intended for use by properly trained and experienced

More information

6 in. Bench Grinder with Worklight

6 in. Bench Grinder with Worklight 6 in. Bench Grinder with Worklight W50001 OWNER S MANUAL SAVE THIS MANUAL Table of Contents Safety Instructions 2 Bench Grinder Safety 3 Electrical Requirements 3 Replacement Parts List 4 Bench Grinder

More information

Handling instructions

Handling instructions Nibbler Model CN 16SA Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these

More information

Heavy Duty Soldering Gun Kit

Heavy Duty Soldering Gun Kit Heavy Duty Soldering Gun Kit Stock Number W2019A OWNER'S MANUAL FOR YOUR SAFETY, please read these instructions carefully and retain them for future use. SPECIFICATIONS Electrical:... 120 V AC, 60 Hz,.07A

More information

DRILL BIT GRINDER MODEL: MR-26A

DRILL BIT GRINDER MODEL: MR-26A DRILL BIT GRINDER MODEL: MR-26A OPERATION INSTRUCTION INTRODUCTION SOME SAFETY ISSUES Common sense and caution are factors which can t be built into any product.these factors must be supplied by the operator.

More information

Automatic Screwdriver Model W 4YD. Handling instructions

Automatic Screwdriver Model W 4YD. Handling instructions Automatic Screwdriver Model W 4YD Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended

More information