Thanks for purchasing this product from RMW. In this manual you find all the information you need to assemble and paint the model.

Transcription

1 PRODUCT INSTRUCTIONS Thanks for purchasing this product from RMW. In this manual you find all the information you need to assemble and paint the model. PRODUCT DESCRIPTION Set of fire brigade trolley models Product No: 0102 These trolleys are used to transport material from the fire engine to the scene of operation. This model contains: 2x compressed (breathing) air trolleys (with vertical and horizontal storage of 24 compressed air bottles), 1x fire extinguisher container, 1x platform trolley, 43 compressed air bottles Example information: e.g. More information can be found via Google (images): Search for Feuerwehr Rollcontainer Scale: 1:87 / H0 Type: kit assembly & painting required Material: semi transparent plastic (Shapeways Frosted Ultra Detail ) Danger! Small parts included Example photos: Model: v0.91 RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 1 of 11

2 PRODUCT COMPONENTS LIST This product consists of: 9 parts on 1 sprue No Description Paint advise A Compressed air bottles trolley (vertical) Frame: silver/grey, panels: dark brown; bottle holders/tubes: black or dark grey A1 Compressed air bottles trolley (vertical) bottom Panel: dark brown B Platform trolley Silver, wheels: grey C Fire extinguisher container trolley Red, wheels: grey C1 Fire extinguisher container trolley front Silver D Compressed air bottles trolley (horizontal) Frame: silver/grey, panels: dark brown; bottle holders/tubes: black or dark grey D1 Compressed air bottles trolley (horizontal) - side Panel: dark brown E 43x Compressed air bottles E1 Compressed air bottles - Separation tool - Yellow, with top silver/black PRODUCT PHOTO: Delivery, before painting & assembly The colors of the individual parts as in this manual, are for illustration purpose only, to make assembly easier! Note: white parts are sprue parts and should be removed A1 is the part below D1. E1 is the part below C1 RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 2 of 11

3 GENERIC INSTRUCTIONS Cleaning: If you have a ultrasonic cleaner (like from Conrad or Harborfreight), use that one with cold or lukewarm water to which you have added some dish-washing liquid to clean the parts for 3 minutes. Alternative, clean the parts by hand in water with dish-washing liquid. You can use a soft toothbrush. For ultra sonic cleaners, refer e.g. to: Separating parts: To separate/cut off all parts from the sprue, you either use a hobby-knife or a small scissors. If you remove the complete sprue from the parts, you might find it more difficult to hold them for painting; so leaving a piece of the sprue to each part might be beneficial (only remove the remaining sprue piece after painting); however, you will not be able to do a test assembly if you leave a piece of the sprue to the part. Painting: Ordinary paint as found in car shop accessories can be used. Hobby acrylic paint should also be fine. First (spray) paint a white base layer. Then multiple layers of your preferred color. After assembly and finishing (decals), use a clear lacquer layer of paint to seal. For White Strong and Flexible plastic material, you will have to use quite a few layers of paint, as the material is porous, so will absorb a lot of paint. Glue-ing: Only use super-glue (cyanoacrylat) Storage: Dust-free at room temperature, protect from UV radiation Working order: First clean the product carefully. Remove remaining oil, grease and wax. Separate all parts from the sprue. Next do the painting, followed by the assembly and finishing. Safety guidelines: During cleaning, painting and assembly of the product, use gloves to protect your hands and goggles to protect your eyes. The product might contain oily grease and wax like support material. If in contact with your skin, clean your skin with abundant water and soap. Before eating or drinking, always clean your hands thoroughly if you have touched the product. RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 3 of 11

4 ADDITIONAL INFORMATION - ASSEMBLY AND PAINTING INSTRUCTIONS Follow the generic instructions on cleaning and separating parts 1 Clean the parts while still attached to the sprue. Cut off the separate parts with a hobby knife or small scissors: do leave pieces of the sprue on the parts, to simplify painting (use to hold the parts) Cut the 4 containers and the bottom/side/front parts (A1, C1, D1) out of the sprue. 2 A1, C1 and D1 should be cut at the round connectors. RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 4 of 11

5 3! You should have all parts except the compressed breathing air bottles separated now, each however with small sprue part left to it (use to hold the part when painting). Clean all parts. Make sure the tubes for the breathing air bottles do not contain any more grease. When cleaning the bottles by hand, be extremely cautious, as the top part easily breaks! Painting Spray painted as many parts as possible, including the breathing air bottles (while in the sprue). The compressed breathing air bottles containers should first be sprayed in the light color (silver/grey), after drying, the tubes should be painted. Same goes for the panels on these containers. NOTE: if you want to display your breathing air bottles inside the tubes, it is best to apply paint by hand only to the top most part of the bottles. Also the tubes should only be painted at the front/top. This as the fit is very tight, and to much paint might result in you not being able to insert or extract the bottles. Refer to diagram below.! 4 Use e.g. a tooth-pick or straw to hold the containers. The bottom/side panels can be stuck to tape. Only after painting and thorough drying continue. Remove the protruding sprue attachment at the front of each container. RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 5 of 11

6 Assembly: 5 PART A Insert A1 into the bottom of A. Do NOT glue, so that part A1 could be taken out, in case of any compressed breathing air bottles should be removed from part A. Apply final touch paint up. Result: 6 Part B Apply final touch paint up. Result: RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 6 of 11

7 Slowly slide part C1 into part C. Press it fully in part C. 7 Apply final touch paint up, e.g. handholds can be highlighted. Result: RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 7 of 11

8 Part D 8 Insert D1 into the side of D. Do NOT glue, so that part D1 could be taken out, in case of any compressed breathing air bottles should be removed from part D Apply final touch paint up. Result: Parts E 11 After (spray) painting while in the sprue, apply the details first (top part), see below. To remove the bottles from the sprue, consider using tool E1 as help. RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 8 of 11

9 Apply final touch paint up. Result: 12 Spray paint all parts with clean lacquer (protective layer). ADDITIONAL INFORMATION PRODUCT PAINTING EXAMPLES RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 9 of 11

10 Example with colors applied Example diorama after painting & assembly. Figures, building, ground cover are not included Refer to our website for more product photos For any questions/suggestions or additional information, contact us at Customer Service Department, us: Website: robs-mw.com Facebook: facebook.com/robsmw Flickr: flickr.com/photos/robs_mw2 Subscribe to our newsletter and/or product updates! DISCLAIMER RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 10 of 11

11 Not included is paint, glue, tools. Decals if applicable for this product - should be self-printed on suitable material. This product is only suitable for the experienced scale modeler (adults, 14 years up). Small parts included! Warning: Please note that the 3D printing materials we use for manufacturing the products make the products suitable only for decorative purposes and they are not suited for any other purpose. The products are not suited to be used as toys, to be given to children. The products should not come in contact with electricity or food & drinks and should be kept away from heat. Due to the new technologies used to fabricate these products, different procedures might need to be used to achieve similar results as for products produced with conventional technologies. Photographs and drawings can show pre-production samples. Subject to alterations in assortment, printing, shape and colors. Technical details information about the example provided as-is RMW-0102-Manual_rollcontainer_set1-v0.91-EN-v0.1 Page 11 of 11