Restoration Project Photo Essay Page 202
|
|
|
- Sheryl Joleen Caldwell
- 5 years ago
- Views:
Transcription
1 Restoration Project Photo Essay Page 202 Photo 397: A new pile of work is ready for me to dive into. The whippens, removed from the action when it was disassembled and piled in a heap, have not been touched since. Photo 398: The first stage to the process of revitalizing the whippens is to set up a work area. The scrap piece of pinblock material will serve as a cutting board to use in slicing off the old felt of each whippen.
2 Restoration Project Photo Essay Page 203 Photo 399: The sticker cloth is cut off of the bottom of the sticker using a sharp chisel in a swivel motion with the point firmly planted in the chopping block. Photo 400: The backcheck felt is also removed using the chisel. The flat side of the chisel stays toward the wooden backcheck to prevent gouging.
3 Restoration Project Photo Essay Page 204 Photo 401: Glue and felt adhering to the wooden backcheck are scrapped off leaving a clean surface to glue new backcheck felt onto. Photo 402: A broken jack spring signals the necessity to replace the entire set of springs. Once a particular part start breaking, total replacement of that part is the best course of action to avoid problems down the road.
4 Restoration Project Photo Essay Page 205 Photo 403: By placing each whippen in the vise, and using a pair of needle nose pliers, the old springs are extracted. The bottom coil of each spring rests in a well. The original springs are ordinarily glued into place. The old glue in this case is brittle, and the springs break loose easily. Photo 404: A jack spring hole reamer attached to an electric drill makes short work of cleaning out well.
5 Restoration Project Photo Essay Page 206 Photo 405: The well cleaned and ready for a new spring. Photo 406: Before anything new is added, however, a burnishing of the bridle strap wires with a miniature wire brush in a Dremel tool is done as a final touch in the cleaning up process.
6 Restoration Project Photo Essay Page 207 Photo 407: Modern art. If this were 20 feet across, signed by Pablo Picasso and hanging in an art gallery, it would be worth millions. I've obviously missed my calling in life. Photo 408: The whippens, now on the opposite side of the bench, are now stripped clean and ready for refelting.
7 Restoration Project Photo Essay Page 208 Photo 409: The hot glue, which has been on for some time, is checked for the correct degree of runniness. Constant monitoring is required to keep the glue at the optimum consistency. The addition of a little water, or a few glue crystals are needed from time to time. Photo 410: The bottom coil of the jack spring is swabbed with hot glue.
8 Restoration Project Photo Essay Page 209 Photo 411: The bottom coil of the spring is then inserted into the well. Photo 412: The whippens are then placed on a rack with the springs straight up and down while the glue cools and cures.
9 Restoration Project Photo Essay Page 210 Photo 413: Remaining vestiges of stubborn dirt around the bridle wire and the backcheck wire is removed with a stiff bristle brush. Photo 414: Dag 154 Graphite lubricant is applied with an artist brush to the nose of each jack. This aids in the free functioning of the jack as it propels the hammer towards the strings. At the last moment before the hammer makes impact, the jack slips out from the hammer butt buckskin, so that the hammer strikes the strings under its own momentum.
10 Restoration Project Photo Essay Page 211 Photo 415: The heel of each jack is likewise lubricated with Dag, so that it slips freely from under the regulating button once contact is made. Photo 416: Newly coated with Dag, the whippens are placed back in the rack to dry once again.
11 Restoration Project Photo Essay Page 212 Photo 417: Backcheck cloth is cut from precut strips. Photo 418: Each backcheck is coated with hot glue.
12 Restoration Project Photo Essay Page 213 Photo 419: The backcheck cloth is positioned and held firmly in place for several seconds. Photo 420: A miniature clamp is then applied with a small rectangle of veneer used to even out the pressure over the length of the cloth.
13 Restoration Project Photo Essay Page 214 Photo 421: For one final time, the whippens are returned to the drying rack to allow the glue to cure. Photo 422: The last two pieces of felt are made ready. The brown sticker cloth is razor cut from a long roll. The hammer butt felts for the topside of the jacks comes precut.
14 Restoration Project Photo Essay Page 215 Photo 423: A square of sticker cloth is glued with hot glue to the bottom of the sticker. This is the contact point between the brass capstan at the back of the key and the whippen. Photo 424: The final piece of felt to be replaced is the square of hammer butt felt which is glued to the topside of the jack.
15 Restoration Project Photo Essay Page 216 Photo 425: The next order of business is to slice the old felt punchings off of the regulating buttons of the let-off rail with a sharp chisel. A light sanding with 100 grit paper finishes this job. Photo 426: Once the punchings are removed, the rail itself is cleaned with a stiff brush.
16 Restoration Project Photo Essay Page 217 Photo 427: New punchings are glued into place with hot glue. Photo 428: The newly refelted let-off rail.
17 Restoration Project Photo Essay Page 218 Photo 429: The flange screws used to attached the whippens to the action are now polished on the wire wheel. My daughter, volunteering to help, took each screw from its numbered hole in the screw holder, polished them, and tossed them in the lid of a jelly jar. Ah, well. Never criticize your children for being helpful. Photo 430: The whippens are laid out on the bench in the correct order for reattachment.
18 Restoration Project Photo Essay Page 219 Photo 431: The jack is held open... Photo 432:...and slid into the action on the front side of the main action rail, while the whippen flange goes in behind it.
19 Restoration Project Photo Essay Page 220 Photo 433: Leaning over the top of the action to start the screw for the whippen flange works well. Photo 434: The sticker flange screw is inserted into the lower action rail.
20 Restoration Project Photo Essay Page 221 Photo 435: The jack spring is compressed slightly with a pair of needle nose pliers, so that its upper coil may be inserted into the well on the bottom of the heel of the jack. Photo 436: The tab on each bridal strap is inserted onto the bridal wire with one hand, while a finger of the other hand trips the jack so that it's in the correct position.
21 Restoration Project Photo Essay Page 222 Photo 437: The bridal wire is bent slightly to the front or to the back in order to produce just a bit of clearance between the nose of the jack and the hammer butt buckskin. Photo 438: With the whippens all reinstalled, the action is returned to the piano for the time being.
22 Restoration Project Photo Essay Page 223 This just won't do at all. With the installation of the whippens a done deal, my attention will next turn to the keys. They are, to put it mildly, in sorry condition. Capstans will be removed and polished, and new molded keytops and new bushings will be installed, but only after a thorough cleaning of each keystick to eliminate all traces of the mouse colony which spent so many years traipsing up and down on top and underneath the keys. Not the most pleasant of jobs, I will assure you, but one that must be attended to and quickly, in that only nine short days remain before the piano is scheduled to be picked up. Yikes! Pass me the Mountain Dew! I need a shot of caffeine!
Restoration Project Photo Essay
Photo 363: The piano action is now ready for its new set of Abel hammers. Titebond glue is swabbed into the predrilled hole in the molding of the hammer using a somewhat flattened Q-Tip. Photo 364: Each
How to install backchecks
How to install backchecks Note: All pictures can be enlarged for better clarification. Revision 7 8/2009 Backchecks wear out in a piano much like brake pads in an automobile. While wear is a valid reason
A S e r v i ce Manual
U p r ig ht Pian o R e gulatio n A S e r v i ce Manual Contents: 1. Clean the instrument... 2 2. Analyze the condition of the instrument... 3 3. Tighten all screws... 4 5. Position of wippen heel to the
Restoration Project / Cable upright Photographic Journal Page 27
Restoration Project / Cable upright Photographic Journal Page 27 Photo 51: With the case work done, keytops are the next project to tackle. I had neglected to get a good before picture of the keys, but
KAWAI GRAND PIANO REGULATION MANUAL
KAWAI GRAND PIANO REGULATION MANUAL Ver 1.4 2011/7/21 Piano Laboratory Supervisor Kazuo Goka 1 Regulation Process Index 1 Tighten all Plate Screws P3 2 Strike Point, Keyframe Position P4 3 Ease Keys P5
Replacing Hammer Butt Springs in the Upright Action
Schaff Piano Supply Company Presents: Replacing Hammer Butt Springs in the Upright Action Basic Procedures By Chuck Behm Replacing Hammer Butt Springs -Rationale- In the restoration of an upright, the
Dampers - number, remove, check bushings/springs, rebush or replace, if nec. Brush spoon felts and replace if nec. Lube (dry e.g.
Player piano restoration/rebuilding checklist (upright version - based on A. Reblitz) NB this is the piano repair/refurbishment (not full rebuilding) version! Player action still gets full rebuild. Evaluation
Photographic Journal Deep Cleaning / Deodorization Project 1887 Weber grand Behm Piano Service, Boone, Iowa
Deep Cleaning Project / Weber grand Photographic Journal Page 1 Photographic Journal Deep Cleaning / Deodorization Project 1887 Weber grand Behm Piano Service, Boone, Iowa Deep Cleaning Project / Weber
The Owner's Guide to Piano Repair Focus On: Replacing Upright Hammer Butt Springs
The Owner's Guide to Piano Repair Focus On: Replacing Upright Hammer Butt Springs Information provided courtesy of: Ed Tomlinson - California Keyboards Music Center 661-342-0367 email: ed@californiakeyboards.com
Service Technicians Manual GRAND PIANOS MECHANISM REGULATION
Service Technicians Manual GRAND PIANOS MECHANISM REGULATION 2008 1 Service Technicians Manual GRAND PIANOS MECHANISM REGULATION 1. General 1.1 Grand Pianos Storage Conditions at Shops and at Customers
WESTERN PISTOL.22 CALIBER SINGLE SHOT. Entire pamphlet Copyrighted by JACO Designs 1972
WESTERN PISTOL.22 CALIBER SINGLE SHOT Entire pamphlet Copyrighted by JACO Designs 1972 This pamphlet contains the plans and instructions necessary to construct the Western pistol. This pistol breaks open
Using The Renner Flange Bushing Cloth Bill Spurlock
Using The Renner Flange Bushing Cloth Bill Spurlock Renner provides superior quality bushing cloth in a variety of thickness and dimensions suitable for most piano bushing applications, such as action
Ball-Joint Scrapers Steel Blade Carbide Blade 05K K21.04
Ball-Joint Scrapers Steel Blade Carbide Blade 05K21.01 05K21.04 The Veritas Ball-Joint Scraper is based on a tool originally made by L.S. Starrett Tool Company but out of production for many years. Originally
Vertical Hammer Replacement...
SPURLOCK SPECIALTY TOOLS 3574 CANTELOW ROAD VACAVILLE, CA 95688 www.spurlocktools.com Vertical Hammer Replacement........ 2006 Bill Spurlock The hammer has a greater affect upon the tone of a piano than
Action Frame Inspection and Repair. DEFINITIONS action spread vertical height differential rake
Action Frame Inspection and Repair DEFINITIONS action spread vertical height differential rake MAKING A FOOT PRINT mark the position of all action brackets, rails, and screws make screw hole spacing template
The Owner's Guide to Piano Repair Focus On: Repairing a Separated Back on the Vertical Piano
The Owner's Guide to Piano Repair Focus On: Repairing a Separated Back on the Vertical Piano Information provided courtesy of: Ed Tomlinson - California Keyboards Music Center 661-342-0367 email: ed@californiakeyboards.com
J D SQUARED INC. NOTCH MASTER Tube and Pipe Notcher Operating Instructions
Copyright (c) 2006 J D SQUARED INC. www.jd2.com NOTCH MASTER Tube and Pipe Notcher Operating Instructions Angled Notches PATENT PENDING Straight Notches Offset Notches Tube Clamp Slider Tube Clamp Exploded
BUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
The Owner's Guide to Piano Repair Focus On: Routine Maintenance for Your Vintage Upright Piano
The Owner's Guide to Piano Repair Focus On: Routine Maintenance for Your Vintage Upright Piano Information provided courtesy of: Ed Tomlinson - California Keyboards Music Center 661-342-0367 email: ed@californiakeyboards.com
Set Part # Rev
Set Part # 21007 Rev-3 06-06-11 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to
APACHE HINGE REPLACEMENT PROJECT
APACHE HINGE REPLACEMENT PROJECT MATERIALS: Aluminum Extrusion, custom lengths Setscrew, stainless steel, 7mm x 10mm hex socket *(optional) Pop Rivets, 3/16", long, aluminum Back Up Spacers, 3/16" (Pop
PRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP PRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-280A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET PRO 400 M401/MFP M425 (CF-280A/X) TONER CARTRIDGE By Mike Josiah
!! " # $ % & '! ( ) * +, -
!! " # $ % & '! ( ) * +, - North Pegasus This carton contains: (1) Instruction package. Response Curves North Creek Cabinet Handbook North Creek Wiring Guide (2) 6 oz. Rolls of Dacron stuffing. (1) Tube
Be sure to oil your machine as instructed below. To avoid spotting on garments being embroidered, oil the machine sparingly.
OILING THE MACHINE Oiling is important for maintaining the machine performance over an extended period of time. Turn the power off when lubricating the embroidery machine. Be sure to oil your machine as
Ford Ranger / Bronco II Set Part # Rev B 5-04
Ford Ranger / Bronco II Set Part # 21008 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).
SAW-PIERCING. 79. Fig. 29. Placing new blade in saw-frame.
SAW-PIERCING. 79 First make a full-size drawing of the hinge, then by means of transfer paper transfer the design of the butt end to the copper or brass. Then lay out the knuckles as shown in Fig. 28,
Hand Tool Identification Worksheet. Name: Screw driver. Purpose: To turn the screws. Name: chisels. Purpose: To remove/chip away materials
Hand Tool Identification Worksheet Name: Screw driver Purpose: To turn the screws Safety Facts: Don t use for prying or as a chisel Name: chisels Purpose: To remove/chip away materials Safety Facts: Always
Windsor Chair Online. Assembly Instructions
Windsor Chair Online Assembly Instructions Date: 1/4/2007 Other Chairs Offered Philadelphia Arm Chair New England Comb Back Sackback d Arm Chair Bow Back Side Chair Fan Back Side Chair Page 1 Table of
Kentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
The Owner's Guide to Piano Repair Focus On: Brass Rail Repair
The Owner's Guide to Piano Repair Focus On: Brass Rail Repair Information provided courtesy of: Ed Tomlinson - California Keyboards Music Center 661-342-0367 email: ed@californiakeyboards.com www.pianotunerbakersfield.com
Bowser drive assembly.
Bowser drive assembly. Since the late 90s the Bowser drive has become the de-facto drive for repowering HO trolley cars. While other available drives fit certain situations the Bowser seems to be the first
Refurbishing Your Lincoln Mark VII Dew Wipes
By Rick One_Way Eckenrode Refurbishing Your Lincoln Mark VII Dew Wipes A common flaw among Lincoln Mark VII s can be found at the top of both doors. The dew wipes (rubber weatherstrip that rests against
Pump Assembly. Lloyd Matthews September 2013
Pump Assembly Lloyd Matthews September 2013 Before proceeding with this part of the build, the author recommends that Pt. No 227 1 mm diameter Brass Wire Figure H1, is replaced with 0.8 mm straight brass
Wagon Vise Retrofit Installation Instructions. American Craft Woodworks. Wagon Vise
Wagon Vise Retrofit Installation Instructions American Craft Woodworks Wagon Vise Wagon Vise Retrofit Installation Instructions 2 Retrofit Installation Instructions Before you get started, please read
Big Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
Woodcraft, 210 Wood County Industrial Park, P.O. Box 1686, Parkersburg, WV
Hancock Wall Clock Assembly Instructions 77A50 07/28/94 Product #C7611X Introduction Before beginning the assembly of your Woodcraft precut clock kit, read these instructions and become familiar with the
AFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST
AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners
Berea Hardwoods Survival Ballpoint Pen
Berea Hardwoods Co., Inc. Pencil Instructions 18745 Sheldon Road Middleburg Heights, Ohio 44130 Toll Free 1-877-736-5487 Survival Ballpoint Pen (Berea #1602/x-xxx- x) Needed: Mandrel-A Bushing-61A Drills-
ARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
Assembly, Use and Care Instructions
Assembly, Use and Care Instructions Product #336677 Instruction #1068318 Rev. F Thank you for purchasing a Caldwell Lead Sled DFT 2. The Lead Sled DFT 2 comes to you partially assembled. It will require
MAKER LAB Safety Instructions Power Tool Training
MAKER LAB Safety Instructions Power Tool Training Note: All the instructions from Basic Training apply to Power Tool Training. If you have not completed Basic Training, do so before you complete Power
Maintenance & Parts list for:
Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide
28 mm. 18 mm. 14 mm. 10 mm Length to fit. 7 mm. 16 mm. 7.5 mm. 18 mm 10 mm 25 mm. 3 mm.032 Brass. Wire. Figure 1: Ground Throw Components
Modified Slanser Ground Throw Switchstand Bill Johnson of the Sunrise Division of the NMRA has demonstrated and documented the Slanser Ground Throw mechanism on several occasions. His design requires the
Page 124. Restoration Project Photo Essay. Photo 251: Stringing tools are laid out and ready to go.
Page 124 Photo 251: Stringing tools are laid out and ready to go. Photo 252: The stringing chart completed during teardown finally comes back into play. Page 125 Photo 253: A set of tuning pins are taken
Darjeeling Coach 4-Wheel First/Second Class
Darjeeling Coach 4-Wheel First/Second Class Introduction This kit was designed in 16mm scale from early Darjeeling drawings and photographs. It uses brass castings available from Brandbright. The instructions
Clocking a TD-04 Turbo Compressor Housing. Appendix A : AWIC Silicone and Tubing Fitting
Clocking a TD-04 Turbo Compressor Housing Appendix A : AWIC Silicone and Tubing Fitting Revision A: 7-13-2015 Tools: Metric Sockets (10, 12, 14, 17mm) 5mm Hex Key Large Internal Snap Ring Pliers 3/8 Socket
BUILDING A GHOST GLOCK. Prepper Mike
BUILDING A GHOST GLOCK Prepper Mike WHAT IS A GHOST GLOCK? Ghost guns are guns that don t need to be registered Ghost guns are built by the owner based on not more than 80% complete lowers Ghost guns are
Adjustable Hammered Dulcimer Stand
Adjustable Hammered Dulcimer Stand Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater MN 55082 651 439 9120 www.harpkit.com PARTS LIST: 1 Set of Assembly Instructions A. 2 front
1 of 12 5/24/2015 9:43 AM
1 of 12 5/24/2015 9:43 AM REAR PROPELLER SHAFT ASSEMBLY Components REMOVAL 1. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 2 of 12 5/24/2015 9:43 AM a. Place match marks on the propeller shaft flange
Practical Scrap Metal Small Arms Vol.10 By Professor Parabellum
Practical Scrap Metal Small Arms Vol.10 By Professor Parabellum Introduction The 9mm submachine gun design described here is extremely basic and can be put together using very limited tools and materials.
Fig2: The Sliding Glue Block from the back.
Ornament Stand Introduction It was one of those forehead smacking moments. I was taking the #2 jaws off my Stronghold chuck, to put on my homemade wooden two jaw chuck set-up. For some reason instead of
Assembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout
Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout By Dwight Ennis In this section, we're going to make the Frost Box, and we'll build the Spout Hanger Assembly
Tortoise Switch Machines, Mounted Horizontally
Tortoise Switch Machines, Mounted Horizontally by David King Have you ever used the Tortoise Switch Machines manufactured by Circuitron. These are a wonderful stall motor slow motion switch machine that
Boxtrot. Tools. Materials:
Boxtrot Sneak downstairs with a little nog and chisel yourself a nice box to hold your New Year's resolutions. Materials: Cut List: 3/8" plywood - preferably high grade, seven-ply, cabinetmakers plywood
FORWARD FUSELAGE SIDES & REAR TOP SKINS
FORWARD FUSELAGE SIDES & REAR TOP SKINS WORK REPORT Step No. Check Parts / Tools Qty Preparations. 1 [ ] 6F5-3 Upper Front Longerons 2 2 [ ] 6F5-5 Heel Support 1 3 [ ] 6F5-2 Front Floor Skin 1 3 [ ] Firewall
Instructions: PS-2CD 4000 Model Kit Revised 7/2008
Instructions: PS-2CD 4000 Model Kit Revised 7/2008 Plastic Parts included: Body shell Parts Sprue #1 Roof, trainline, gravity outlet gates, and centersill/endsill pieces Parts Sprue #2 Underframe bolster
Gold Wire Paper Clip Chain Wire Jewelry Making Pattern #103
Gold Wire Paper Clip Chain Wire Jewelry Making Pattern #103 More Jewelry Making Patterns at http://wire-sculpture.com/patterns/ Supplies Needed * Approximately 4 feet of 21 gauge 14 karat gold filled square
Shay Tender Frame Fabrication
Shay Tender Frame Fabrication Nelson Riedel Nelson@NelsonsLocomotive.com Initial:3/15/03 Last Revised: 06/05/2004 This page shows additional detail on the tender frame members and some of the processes
Various Bolt Removal Process
Various Bolt Removal Process Introduction I have been climbing close to 30 years. The first bolt I placed in 1987 was a 5/16 Rawls carbon steel, split shank, button head in sandstone. Certainly the wrong
CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS
20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air
The finished ornaments.
Introduction I like to make different Christmas Ornaments every year to give to my relatives. This article describes the rnaments that I m making this year. The ornaments use a split turning of either
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
WPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
Building Instructions Diva cabin boat
Building Instructions Diva cabin boat Order no. 3093/00 aero-naut Modellbau Stuttgarterstr. 18-22 D-72766 Reutlingen / Germany http://www.aero-naut.com 1 For pictured building instructions please see the
About.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
Be sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
Building a 30 Turntable
Building a 30 Turntable Introduction I wanted a turntable at the North end of my Mystic Mountain railroad to turn trains for point-topoint running and for visual interest. After measuring all my engines
Assembly instructions
Nerdy Gurdy Assembly instructions This manual describes how to assemble a Nerdy Gurdy. Go to http://www.nerdygurdy.nl for more info about these instruments. Jaap Brand The Netherlands January 2018 General
Instructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
Upright Hammer Replacement
Schaff Piano Supply Company Presents: Upright Hammer Replacement By Chuck Behm Upright Hammer Replacement -Rationale- Piano hammers are amazingly resilient, considering the fact that for the hammers to
Bulle Clock Serial Number 57561
Page 1 Restored Bulle Clock Bulle Clock Serial Number 57561 Page 2 Restored Bulle Clock Clock Restoration pictures by kind permission of the owner. The clock as delivered. It came without a case and the
No-Mar tip conversion/replacement procedure
No-Mar tip conversion/replacement procedure This procedure can be used for customers who want to convert their legacy Delrin demount tips to the new No- Mar tips, or for customers that just need to replace
MOXON VISE. History. Contents: (2) Cast iron handwheel (2) acme screw (4) acme nut (2) thick washer (1) Crubber jaw liner
Assembly & Installation Instructions For: MOXON VISE History Contents: (2) Cast iron handwheel (2) acme screw (4) acme nut (2) thick washer (1) Crubber jaw liner Joseph Moxon s double-screw vise described
Solo AD Style DIY Acoustic Guitar Kit
Solo AD Style DIY Acoustic Guitar Kit Assembly Manual ADK-1 V 2.0 Copyright 2017 Solo Music Gear. All rights reserved Show Off Your Custom Built Guitar! When you have your guitar finished, please take
Star Trek TOS communicator upgrade kit Install instructions Hyperdyne Labs 2002
Star Trek TOS communicator upgrade kit Install instructions Hyperdyne Labs 2002 Package Your package should include: Assembled TOS sound/motor/light board with LEDs and sound chip Moiré motor 9V snap connector
Art Rack Assembly Instructions:
Art Rack Assembly Instructions: ** PIECES ARE POWDER COATED Do not lay pieces on top of each other or on a hard, rough surface if possible. All bolts will pass from outside towards inside of the cage.
15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
Car Construction E-Book
Physics Lecture 14 - Building the Simple But Fast (SBF) Car-Part 1 Introduction The following lecture uses information from the Car Construction E-Book on the Virtual Race CD. This Lecture does not, however,
An All-Balsa Sportster
An All-Balsa Sportster A REMARKABLE FLIER OF UNIQUE DESIGN THAT WILL GIVE YOU MANY ENJOYABLE BUILDING AND FLYING HOURS By STAN D. MARSH Contributions by Felix Gutmann This model was designed primarily
EllisSaw.com. EllisSaw.com P.O. Box Verona, WI
P.O. Box 9019 Verona, WI 9-019 GENERAL OPERATING & SAFETY INSTRUCTIONS * READ INSTRUCTIONS BEFORE USE * CAUTION: Disconnect power supply cord from power source when doing repair work or changing belt.
Make your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
Grinders, Sanders, Drills, Lathes, Saws, Shear, Break, Punch, And Roller
Grinders, Sanders, Drills, Lathes, Saws, Shear, Break, Punch, And Roller Personal Protective Equipment: A welder must be aware of possible dangers to the body during any welding or cutting operation and
Bullet Pen Casing. Contributed by: David Bell. This tutorial was downloaded from.
Bullet Pen Casing Contributed by: David Bell This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2014 This tutorial is designed around the bullet casing
HP M506/MFP M527 CF-287A/X
HP M506/MFP M527 CF-287A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-287A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET ENTERPRISE M506/MFP M527 CF-287A/X TONER CARTRIDGE By Mike Josiah and
How I Made My Aluminum Slim Line Pen
- 1 - How I Made My Aluminum Slim Line Pen Written by Joe Agrella http://www.joespens.com - 2 - Getting Started First and formost remember safety. Remember that you will need eye protection and plenty
Invisible Ivory Keytop Replacement
Invisible Ivory Keytop Replacement Basic Step-by-Step Procedures By Chuck Behm / Invisible Keytop Replacement Invisible Ivory Keytop Replacement -Rationale- Having the capability to offer a variety of
Dillon XL 650 Spent Primer Catch Upgrade Instructions. (Please read through all of the steps before beginning.)
Dillon XL 650 Spent Primer Catch Upgrade Instructions. (Please read through all of the steps before beginning.) Using a 3/32 Allen Wrench start by loosening the two screws that hold the Spent Primer Cup
Invisible Clip Tutorial
Invisible Clip Tutorial I first saw what I call the Invisible Clip in Russ Fairfield s PMG gallery and fell in love with it. I could not figure out how he made them so I sent him an e-mail and he was kind
Various Bolt Removal Process
Various Bolt Removal Process Introduction I have been climbing for over 25 years. The first bolt I placed in 1987 was a 5/16 Rawls carbon steel, split shank, button head in sandstone. Certainly the wrong
Part 2 Section 2 POINTWORK
Part 2 Section 2 POINTWORK Issued November 2001 2.4 Basic turnout construction For those modellers who wish to build their own turnouts, there is a range of construction materials and methods to choose
Razr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada
Razr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada The following is a description of the process that I have used to modify the console eject box for e38, e39, e46 and x5 s, part number 84-21-6-933-415.
All American Mower Blade Sharpener Mulching Blade Model Patent Pending
All American Mower Blade Sharpener Mulching Blade Model 5000 Patent Pending Revised May 3, 2017 Attaching the guide pin to your grinder: Assembly and Use Locate the guide pin (included with the sharpener)
Greene & Greene. Mailbox. by Seth Keller. Signature details create an elegant box. 2 AmericanWoodworker.com
Greene & Greene Mailbox by Seth Keller Signature details create an elegant box. 2 AmericanWoodworker.com We needed a new mailbox, but I couldn t find an off-the-shelf version that I liked. So I decided
ADVANCED ROTARY CUTTER & TABLE EDGE ADVANCED ROTARY CUTTER
1 ADVANCED ROTARY CUTTER & TABLE EDGE ADVANCED ROTARY CUTTER F D E I INSTRUCTION MANUAL MANUEL D INSTRUCTIONS GEBRAUCHSLANLEITUNG MANUAL DE INSTRUCCION MANUALE DI ISTRUZIONI 2 6 10 14 18 THE WORLD S FINEST
TURNING A PEN ORIGINAL BY MIKE RUDE REVISED BY GORDON PATNUDE - AUGUST 2015, OCTOBER 2016 EQUIPMENT AND SUPPLIES NEEDED
TURNING A PEN ORIGINAL BY MIKE RUDE SEPT 2006 REVISED BY GORDON PATNUDE - AUGUST 2015, OCTOBER 2016 PHOTOGRAPHY BY JIM GOTT AUGUST 2015 EQUIPMENT AND SUPPLIES NEEDED A PEN TURNING TUTORIAL [this document]
ASSIGNMENT 4. Textbook Assignment: The point, edge, face, heel, and tang are the five parts of which of the following tools?
ASSIGNMENT 4 Textbook Assignment: "Files," "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and
Christmas Bell Ornament
Christmas Bell Ornament This is an easy Christmas ornament idea I cabbaged from a friend and skilled turner, Curt Fuller, from Utah. I kind of adapted it to my style but I still got the idea from him.
UNPACK & ASSEMBLY. Done! CAUTION! THE MILL WILL BE VERY HEAVY - GET ASSISTANCE Pepe Tools.
PARTS DIAGRAM T Bar Height adjustment Wooden hand grip Height adjustment gears Frame Height adjustment screws Top roller End Gears cover Handle Brass Bushes (Each side) Bottom roller 4:1 Gearbox Mounting