Head Serial Number : Date Purchased : Where Installed: DB75, DB75V & DB75VS OPERATION AND MAINTENANCE MANUAL
|
|
- Reynold Washington
- 5 years ago
- Views:
Transcription
1 DELUXE STITCHER COMPANY INC. solving your wire stitching needs for 125 years... Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75, DB75V & DB75VS OPERATION AND MAINTENANCE MANUAL DB75HD231/2...Stitcher Head...23 Wire DB75HD251/2...Stitcher Head...25 Wire DB75HD20241/2..Stitcher Head..20x24 Wire DB75VHD231/2...Stitcher Head...23 Wire DB75VHD251/2...Stitcher Head...25 Wire DB75VHD20241/2..Stitcher Head..20x24 Wire DB75VSHD231/2...Stitcher Head...23 Wire DB75VSHD251/2...Stitcher Head...25 Wire DB75VSHD20241/2..Stitcher Head..20x24 Wire Before using this Stitcher Head, all operators must study this manual and follow the safety warnings and instructions. Keep these instructions with the Stitcher Head for future reference. If you have any questions, contact your local DeLuxe Stitcher Representative or Distributor.
2 WARNING! DB75/75V/75VS Heads Machine operators and others in the work area should always wear safety glasses to prevent serious eye injury from fasteners and flying debris when loading, operating, or unloading the stitcher machine. Do not operate this stitcher head without all stitcher machine guards in place. Do not modify the guards in any way. Always disconnect the power supply before removing any guards for servicing. Never operate the machine with wire feeding through the head unless there is stock above the clinchers, otherwise serious damage may result. Always turn power off when making adjustments. Always disconnect the power cord before any disassembly work. EYEWEAR REQUIRED 1
3 THANK YOU FOR CHOOSING THE DB75, DB75V, OR DB75VS STITCHER HEAD FOR YOUR BINDING NEEDS 2
4 Table of Contents Introduction...4 Specifications...5 Installation...6 Pre-Inspection...6 Inspection...6 Mounting...6 Assembly Operation...9 Wire Threading Wire Straightening...11 Adjustments and Settings Maintenance...14 Lubrication Ordering Spare Parts...16 Troubleshooting Appendices...19 Exploded Drawings Notes...37 Part Number/Description Cross Reference Index Registration Card...40 Wear/Replacement Parts...41 Warranty
5 Introduction The DeLuxe Stitcher Müller-Martini Replacement Heads, along with a complete line of fully interchangeable replacement parts are available for current Müller-Martini users. Anywhere the HK75, HK75V and HK75VS are utilized the DeLuxe Stitcher DB75HD, DB75VHD, & DB75VSHD can be used. The DB75HD has a stitching capacity from 2 sheets up to 5mm (.197 ) and will accommodate wire sizes from gauge round as well as 21 x 25 and 20 x 24 flat. The perfect replacement head for Müller-Martini Stitchers 221, 235, 321, 335, Prima, Bravo and more, the DB75HD is completely interchangeable. The DB75VHD & DB75VSHD have a stitching capacity from 2 sheets up to 6mm (.236) and will accommodate wire sizes from gauge round as well as 21 x 25 and 20 x 24 flat. This replacement head for Müller-Martini Stitchers 301, Tempo, Optima, Supra and the like, is also completely interchangeable. Each of these heads weighs 7 lbs (3.2 kgs.) independently. The packaged shipping weight including the Wire Guide Spring, Clincher Plate assembly and user manuals is 10 lbs. (4.5 kgs.). Always use a high quality Galvanized Wire so the plating does not peel. Excessive peeling will cause clogging and the premature wear of many components. Use the following chart as a guide for wire gauge usage. 2 sheets - 1/8 (3mm)...25 gauge 1/8 (3mm) - 7/32 (6mm)...23 or 24 gauge For heavy paper...20 to 22 gauge round or 20x24 flat NOTE: ALL PRODUCTS ARE MANUFACTURED BY DELUXE STITCHER. 4
6 Specifications Weight: Shipping Weight lbs (4.5 kg) Box Dimensions... 21" x 10" x 7" (53 x 25 x 18 cm) Stitcher Head: DB75HD... 7 lbs (3.2 kg) DB75VHD... 7 lbs (3.2 kg) DB75VSHD... 7 lbs. (3.2 kg) Physical Dimensions Height (22 cm) Width (9 cm) Depth (11 cm) Stitching Capacity DB75HD... Two Sheets to 13/64 (5 mm)* DB75VHD... Two Sheets to 1/4 (6 mm)* DB75VSHD... Two Sheets to 1/4" (6mm)* Wire Types through 28 round or 21 x 25 and 20 x 24 flat * Actual stitching thickness capacity depends on the type of stock being stitched and the capacity of the saddle stitcher being used. Stitcher Machine Stitcher Head / Stitcher Machine Compatibility Compatible Stitcher Heads JGV DB75HD DB75VHD DB45HD Loop not recommended. X Fox, 221, 235 DB75HD DB75VHD DB45HD DB75VHD-LOOP X 331, 335 DB75HD DB75VHD DB45HD DB75VHD-LOOP X Bravo/Prima (Built before 2004) Bravo/Prima (Built 2004 or later) Valore/Presto (All) 1509/Minuteman (Built before 2004) 1509/Minuteman (Built 2004 or later) 301/Optima/ Tempo/Supra DB75HD DB75VHD DB45HD DB75VHD-LOOP X DB75LPHD DB75VLPHD DB45LPHD DB75VLPHD-LOOP X DB75MPHD DB75VMPHD DB45MPHD X X DB75MMHD DB75VMMHD DB45MMHD DB75VMMHD-LOOP X DB75MMMPHD DB75VMMMPHD DB45MMMPHD DB75VMMMPHD-LOOP X X X X X DB75VSHD 5
7 Installation Pre-Inspection Carefully inspect the condition of the shipping container before unpacking your replacement Head for Müller-Martini Stitchers. If the container is broken or damaged and there is evidence that the (DB75) or C (DB75V/VS) stitcher head may be damaged, immediately notify the carrier who delivered the head and the DeLuxe Stitcher Graphic Arts Representative from whom the Head was purchased. G20362 (5 mm) G20361 (2.5 mm) G20360 (3 mm) G20373 (4 mm) Inspection (Figure 1) As you carefully unpack the replacement head, check to make sure all components were delivered and are in good working order. Use Figure 1 in this manual for reference to the following pieces: Figure 1 - Inspection Replacement Head for Müller Martini Stitchers: DB75HD, DB75VHD or DB75VSHD Wire Guide Spring [070286] Clincher Plate Assembly [ or C] Feed Release Handle [070119] 2.5, 3, 4 and 5mm Hex Key Wrenches [G20361, G20360, G20373 and G20362] Stitch samples Mounting & Assembly (Figure 2-6) Attaching the Feed Release Handle (Figure 2) Screw Spring From out of the box, secure the Feed Release Handle [070119] to the Stitcher Head by slipping the Handle over the Feed Release Cam Assembly [070118] and securing it with the provided screw, inserting it through the Spring. Make sure the Handle is angled toward the outside of the Head when you the screw is tightened. Handle Figure 2- Feed Release Handle 6
8 Washer (2) Screw (2) Wire Guide Spring Figure 4 - Attaching the Wire Guide Spring Driver Slide A or A Bonnet Rail Bender Slide A or A Feed Release Cam Feed Release Handle Bonnet Key Lock Washer G20520 Figure 3a - Mounting the Head Mounting Strap BB or BB Mounting Screw Mounting the Head ( See Figure 3) Attaching the Wire Guide Spring (Figure 4) Figure 3b - Mounting Variation for DB75VS 7
9 Mounting the Clincher Plate (Figure 5 & 6) Figure 5 - Mounting Clincher Plate Assembly Clincher Mounting Bar Clincher Points (2) Clincher Slide or C Mounting Screws (2) Figure 6 - Aligning Clincher Plate Assembly Clincher Front Plate Clincher Plate Assembly Clincher Front Plate Lock Washers G20520 (2) CAUTION!! Always disconnect the power before assembling or making adjustments to your stitcher machine. 8
10 Operation Wire Threading (Figure 7-8) Figure 7 - Wire Threading Wire Guide Spring Feed Release Handle Wire Oiler Felts G20293 Small Feed Gear Wire Wire Nozzle ENGAGE GEARS Large Feed Gear A DISENGAGE GEARS Retaining Spring Screw Wire Holder Retaining Spring or
11 Before the Stitcher Machine is turned on, release the Wire Holder Assembly [070135A] (Not shown- See Fig. #) secured by the Wire Holder Retaining Spring [ or ] by loosening the Screw [072004] on the front of the Head. Thread the wire from the Spool under the studs on the Wire Guide Spring (070286), between the Wire Oiler Felts [G20293] on the Spring and into the Wire Nozzle [070181]. Turn the Feed Release Handle [070119)] clockwise so that the Small Feed Gear [070112] is disengaged from the Large Feed Gear [070510A]. Continue to push wire through the Replacement Head until the end of the wire passes the Small and Large Feed Gears, enters the Wire Tube [070544] and begins to come out the bottom of the Wire Tube. Then using a small screw driver, wedge the wire up until it enters the Fixed Wire Cutter [070600C]. Engage the Small and Large Feed Gears by turning the Adjustable Lever counter-clockwise. Note: It will take two full cycles for the proper length staple to come out of the Head. Figure 8 - Wire Threading Wire Tube Fixed Cutter C Bottom View 10
12 Wire Straightening (Figure 9) Once threaded, cycle the Stitcher Machine and watch the wire feeding out of the the Cutter Box [070197A or A] to the right of the Moving Cutter [070145C]. The wire should be traveling in an approximate horizontal direction when exiting the Cutter Box. Top-to-Bottom Adjustment If the Wire is feeding in an upward or downward direction, the Wire Straightener [070206A] will have to be adjusted. Loosen the Screw [G20589] securing the Wire Straightener to the Cutter Box. If the wire is feeding in an upward direction, slide the Wire Straightener down slightly. Conversely, if the wire Moving Cutter C Figure 9 - Wire Straightening Screw G20589 is feeding in a downward direction, slide the Assembly up slightly. Make sure to tighten the Screw after every adjustment to see accurate results. Allow enough Wire to be fed through the Head so that an accurate assessment can be made. Make sure the ends of each cut piece of Wire is free of burrs, which would negatively affect the driving and clinching of the formed Wire. Bad Wire Straightener A Good Bad WARNING! Make sure the Wire Holder Assembly has been removed before tripping the Machine to avoid jams and the chipping of parts. 11
13 Adjusting the Length of the Right Leg (Figure 10-12) Setting the Stitch s Right Leg (& Setting It's Center) If after a few stitches, the length of the stitch s right leg is too short or too long, you will need to make adjustments. Adjustments are always made to the right leg to compensate for the length of the left leg. First adjust the stitch s right leg to match the left and then make adjustments for the overall length of the stitch or wire draw. Power off the Stitcher Machine and release the Extension Spring [074002] from the Feed Gear Operating Lever Pin [043002] on the Replacement Head. Disengage the Small Feed Gear from the Large Feed Gear by turning the Feed Release Handle [070119]. Push the Feed Gear Operating Lever [077001] down which will move the pin on the Feed Gear Pinion [070111A] out of the way of the Feed Gear Stop [077026]. Loosen, but do not remove, the Screw [G20589] securing the Feed Gear Stop to the top of the Cutter Box Assembly. If the legs of the stitch are not even, do one othe following: Feed Gear Pinion Pin Feed Gear Stop Screw G20589 If the right leg is too Figure 10 - Adjusting the Right Leg short, slide the Feed Gear Stop to the left slightly, to lengthen it. Extension Spring Feed Gear Operating Lever Feed Release Handle Feed Gear Stop If the right leg is too long, then adjust the Feed Gear Stop slightly to the right. Tighten the screw and replace the Extension Spring. Right Leg Too Short Right Leg Too Long Figure 11 - Adjusting the Right Leg CAUTION! Always disconnect the power before assembling or making adjustments to your stitcher machine. 12
14 Power on the Stitcher Machine and jog the Stitcher to observe the length of the stitch s right leg after the initial adjustment. Continue to make adjustments and re-test the Head until the length of the stitch s right leg is satisfactory. When set, any one of the above stitches are regarded as good stitches with the two on the left needing the next step in adjustment and the two on the right as properly set (with amount of gap a matter of preference). Good. Legs are equal, but needs gap adjustment or more or less wire draw. Good with no further need for adjustments Figure 12 - Adjusting the Stitch Adjusting the Stitch Gap or Wire Draw (Figure 13) Adjusting the Overall Length of the Stitch (Adjusting the Stitch Gap) To change the overall length of the stitch, or more specifically to change the gap between the legs of the stitch, the position of the Cutter Box must be adjusted. Begin by releasing the Extension Spring from the Feed Gear Operating Lever Pin. Disengage the Small Feed Gear and the Large Feed Gear by turning the Feed Release Handle. Push the Feed Gear Operating Lever down which will move the pin on the Feed Gear Pinion Pin out of the way of the Feed Gear Stop. Loosen the Screw [072006] securing the Cutter Box to the Stitcher Head. If the legs are too short, increase the overall length of the stitch s legs by sliding the Cutter Box to the left and if too long, to the right. Tighten the Screw, attach the Extension Spring and power on the Stitcher Machine. Trip the Stitcher to observe the overall length of the each stitch after the initial adjustment. Repeat as necessary. Figure 13 - Adjusting the Stitch Gap MORE WIRE DRAW/NARROW GAP Cutter Box Support Screw LESS WIRE DRAW/WIDEN GAP 13
15 Adjusting the Clincher Points (Figure 14) If the clinch on the staple is not tight enough, the Clincher Points [077015] have to be raised. Conversely, if the clinch is too tight, the Clincher Points have to be lowered. This adjustment is made on the Stitcher Machine and so cannot be completely explained in this manual as each individual Machine is different. The final position of the Clincher Points should be flush (or slightly above flush) with the Clincher Plates. The best way to see the position of the Clincher Points is to jog the Machine where the Stitcher Head is mounted. When the Driver is at the lowest position of its stroke, the Clincher Points are at their highest position. Jog the Stitcher Machine until the Stitcher Head is just past this point to reveal the Clincher Points position. To be sure that the Points are at the best position possible, run a few test stitches and compare the clinched staples. Clincher Points (2) Driver , , , , , Figure 14 - Adjusting Clincher Points! CAUTION! Always disconnect the power before assembling or making adjustments to your stitcher machine. Maintenance Lubrication (Figure 15) Use any standard S.A.E. #10 oil for lubricating the heads. Heads that are in constant operation should be lubricated daily. Heads that are operated periodically should be lubricated every five pound wire spool change or every month, which ever comes first. Usually, only a drop of oil is required at each lubrication point. Care must be taken that those parts of the head that contact the work to be stitched are free of oil. Lubricate regularly instead of excessively. Excessive oiling will result in work becoming spotted with oil. Use one drop of oil in the following lubrication points: 14
16 At the top of the Bonnet [ or ] on either side of the Driver Slide [070551A or A] and Bender Slide [070162A or A]. 2. In the hole of the Feed Cam Plunger Bushing [077010]. 3. On the shaft of the Feed Release Cam Assy. [070118] in the front of the Small Feed Gear [070112] The oil hole in the front of the Bonnet [ or ] - this lubricates the Clutch Bearing located inside the Feed Gears 5. On the Cutter Operating Lever 1 7 [070230] behind the Cutter Box [070197A or A]. 6. In between the Wire Holder Retaining Spring [ or ] and the Wire Holder [070135A] and on the Hook Pivot Pin [073009] in the Wire Holder [070135A] 2 Figure 15 - Lubrication and Cleaning 7. On each of the Clincher Point Pivot Pins [ ] on the Clincher Back Plate [077018] 15
17 Feed Gear Information (Figure 16) Correct clutch assembly. 1 Freewheel Transmit Torque Figure 16 - Feed Gear Pinion Assy Ordering Spare Parts Always disconnect the power cord before any maintenance is done or adjustments are made to the Müller Replacement Head???! CAUTION! In time, you will need to replace some parts in your G5 style Stitcher Head. When this happens, first locate the needed part in one of the following diagrams. Then locate the DeLuxe Stitcher part number and contact your Graphic Arts Representative to order the part by the part number, description and quantity. Customer Service Hotline: solving your wire stitching needs for 125 years... 16
18 Troubleshooting (Figure 17) The quality and quantity of work that can be produced with the Müller Replacement Head is dependent upon the operator making all adjustments as accurately as possible and carefully maintaining the head. The cause of staple imperfections usually can be traced to inaccurate settings or normal wear of moving parts. In the event of trouble of this nature occurring, the operator can, by referring to the following troubleshooting chart, quickly locate and remedy the cause or causes of the trouble. The following is a brief list of problems and solutions which should cover the majority of situations encountered when stitching with the DB style Stitching Heads. 17
19 problem: Right Leg Short solution: Move the Feed Gear Stop to the right, slightly. (See page 11) problem: Right leg Long solution: Move the Feed Gear Stop to the left, slightly. (See page 11) problem: Corner Buckled solution: Check the Driver for a chipped corner and rotate or replace it if needed. Use a heavier gauge wire. problem: Leg(s) Buckled solution: Check the Wire Cutters and Wire Cutter Operating Slide for wear and rotate or replace if needed. Use a heavier gauge wire. problem: Crown Buckled solution: Check Supporter Spring tension on the Head. If it is too loose replace it. problem: Stitch in Pieces solution: Clean and lubricate the Head. Check for hard or brittle wire and replace. Check the tension of the Wire Holder Spring and replace Spring if too loose. Look for wear in Wire Holder pivot point in Bonnet. problem: Loose Clinch solution: Raise the Clincher Points. (See page 13) problem: Legs are Spread or Contracted solution: Make sure the wire is feeding straight through the Head. (See page 10) Check the Wire Cutters for wear and rotate or replace if needed. Check the Formers for wear in the grooves and replace if needed. problem: Wire jam near Feed Gear solution: Tighten Cutters. Check for the following worn parts and replace if necessary. Fixed Cutter, Moving Cutter, Cutter Operating Slide, Cutter Operating Lever, Bender Slide Insert, Wire Guide, Hook, Hook Pivot Pin and Feed Gear Friction Strip. Figure 17 - Troubleshooting 18
20 Bonnet and Wire Guide Spring Sub-Assemblies DB75 PARTS USED FOR: MINUTEMAN OR 1509 STITCHERS PW10.6 UA G G20293 (2) G20589 G G20292 (2) G G (2) G (2) B (2) (2) SHADED PART NUMBERS DENOTES WEAR PARTS 19
21 Bonnet and Wire Guide Spring Sub-Assemblies; DB75 DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Bonnet - DB Feed Gear, Small Feed Gear Shaft Feed Release Cam Assembly Feed Release Handle Wire Tube Upper Wire Tube Wire Holder Retaining Spring Friction Strip Cutter Operating Lever Wire Tube Clamp Wire Guide Spring G20520 Lock Washer, M Lock Washer, Ribbed, M Lock Washer Ribbed, M Lock Washer, Ribbed, M Screw M6x1.0x Screw M3x.5x Screw M6x1.0x Screw M5x0.8x E-Ring Spring Pin, M3x Spring Pin, M3x Spring Pin, M3x Dowel Pin, M6x Compression Spring Feed Cam Plunger Feed Cam Plunger Bushing B Mounting Strap G20195 Screw M6x1x8 G20287 Wire Oiler Felt Spring G20292 Wire Oil Felt Washer G20293 Wire Oiler Felt, 1-1/4 Dia. G20297 Screw M6x1x40 G20298 Nylock Lock Nut M6x1 G20589 Screw M4x0.7x10 20
22 Bonnet and Wire Guide Spring Sub-Assemblies DB75V & DB75VS G or [DB75VS] G20293 (2) or G B G20195 G (2) G20292 (2) G (2) (2) (Used on DB75VS only.) or C [DB75VS] (5/8"/15mm Crown-OSK138) (2) (2) or A [DB75VS] or A (2) SHADED PART NUMBERS DENOTES WEAR PARTS 21
23 Bonnet and Wire Guide Spring Sub-Assemblies; DB75V & DB75VS DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Wire Guide Spring Feed Cam Compression Spring Feed Gear, Small Feed Release Cam Assembly Feed Release Handle Upper Wire Tube Cutter Operating Lever Wire Tube Clamp Lower Wire Tube Lock Washer, Ribbed, M Lock Washer, Ribbed, M Screw M3x.5x Screw M6x1.0x Screw M5x0.8x E-Ring Spring Pin, M3x Dowel Pin, M6x Compression Spring Feed Cam Plunger Feed Cam Plunger Bushing Feed Cam Plunger Bushing B Mounting Strap, DB75V Shim Washer, DB75VS A Small Feed Gear, DB75VS A Feed Release Cam Shaft Assembly C Cutter Operating Lever-Carbide G20195 Screw M6x1x8 G20287 Wire Oiler Felt Spring G20292 Wire Oil Felt Washer G20293 Wire Oiler Felt, 1-1/4 Dia. G20297 Screw M6x1x40 G20298 Hex Nut M6x1 22
24 Bonnet and Supporter Sub-Assemblies DB75V & DB75VS (DB75VS requires the addition of plastic liner Part # OSK See Page 20.) G G G (5/8"/15mm Crown ) (5/8"/15mm Crown B) (5/8"/15mm Crown ) G20520 (2) (2) SHADED PART NUMBERS DENOTES WEAR PARTS 23
25 Bonnet and Supporter Sub-Assemblies; DB75V & DB75VS DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Feed Gear Shaft Friction Strip Supporter Spring Bonnet - DB75V Supporter Wire Holder Retaining Spring Lock Washer Ribbed, M Screw M6x1.0x Screw M6x1.0x Screw M4x0.7x Spring Pin, M3x Dowel Pin, M6x Supporter Holder Wire Holder Guide G Screw M6x1x8 G Lock Washer Ribbed, M6 G Screw M4x0.7x10, Nylon 24
26 Driver and Bender Inserts DB A (ASSEMBLY) A (ASSEMBLY) (0.6 mm) (0.8 mm) (1.0 mm) (2) R-25 (0.6 mm) R-23 (0.8 mm) R-20 (1.0 mm) L-25 (0.6 mm) L-23 (0.8 mm) L-20 (1.0 mm) (3) (3) SHADED PART NUMBERS DENOTES WEAR PARTS 25
27 Driver and Bender Inserts; DB75 DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Shim Washer Lock Washer Ribbed, M Screw M5x0.8x Screw M4x0.7x Screw M4x0.7x Cotter Pin Rivet Center Guide Spring Centering Guide Post Centering Guide Driver Slide Shaft Set Collar , Hook Guide, DB Bender Slide Insert A Driver Slide Assembly Driver 1.0 Wire Driver 0.8 Wire Driver 0.6 Wire A Bender Slide Assembly L Former LH 1.0 Wire L Former LH 0.8 Wire L Former LH 0.6 Wire R Former RH 1.0 Wire R Former RH 0.8 Wire R Driver 0.6 Wire Lock Washer Ribbed, M Screw M4x0.7x Screw M4x0.7x6, Nylon 26
28 Driver and Bender Inserts DB75V A (Assembly, includes ) A (5/8"/15mm Crown A) (Assembly, includes & ) (0.6 mm) (0.8 mm) (1.0 mm) 5/8"/15mm Crown (0.6 mm) (0.8 mm) (1.0 mm) R-25 (0.6 mm) R-23 (0.8 mm) R-20 (1.0 mm) 5/8"/15mm Crown R-25 (0.6 mm) R-23 (0.8 mm) R-20 (1.0 mm) (5/8"/15mm Crown B) L-25 (0.6 mm) L-23 (0.8 mm) L-20 (1.0 mm) 5/8"/15mm Crown L-25 (0.6 mm) L-23 (0.8 mm) L-20 (1.0 mm) (3) (3) (5/8"/15mm Crown ) SHADED PART NUMBERS DENOTES WEAR PARTS 27
29 Driver and Bender Inserts; DB75V DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Shim Washer Lock Washer Ribbed, M Screw M4x0.7x Screw M4x0.7x Driver Retaining Screw Allen Head Screw Cotter Pin Center Guide Spring Driver Slide Shaft Set Collar Bender Slide Insert Centering Guide, Wide Centering Guide, Narrow Hook Guide, DB75V L Former LH 1.0 Wire L Former LH 0.8 Wire L Former LH 0.6 Wire R Former RH 1.0 Wire R Former RH 0.8 Wire R Former RH 0.6 Wire A Driver Slide Assembly Driver 1.0 Wire Driver 0.8 Wire Driver 0.6 Wire A Bender Slide Assembly R Former RH 1.0 Wire R Former RH 0.8 Wire R Former RH 0.6 Wire L Former LH 1.0 Wire, 15mm Crown L Former LH 0.8 Wire, 15mm Crown L Former LH 0.6 Wire, 15mm Crown Driver 1.0 Wire-15mm Crown Driver 0.8 Wire-15mm Crown Driver 0.6 Wire-15mm Crown 28
30 Driver and Bender Inserts DB75VS (2) A G A (2) G MATL (includes ) A MATL (includes C) (0.6 mm) (0.8 mm) (1.0 mm) C R-25 (0.6 mm) R-23 (0.8 mm) R-20 (1.0 mm) (3) L-25 (0.6 mm) L-23 (0.8 mm) L-20 (1.0 mm) (3) GREASE AS SHOWN ON PRECEDING DB75V PAGE SHADED PART NUMBERS DENOTES WEAR PARTS 29
31 Driver and Bender Inserts; DB75VS DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Shim Washer Lock Washer Ribbed, M Driver Retaining Screw, Nylon Allen Head Screw Cotter Pin Center Guide Spring Centering Guide, Wide Centering Guide, Narrow Bearing, Mount Shaft, DB75VS Slide Bearing, DB75VS Shim, DB75VS Hook Guide, DB75VS L-20 (1.0 mm) Former LH 1.0 Wire L-23 (0.8 mm) Former LH 0.8 Wire L-25 (0.6 mm) Former LH 0.6 Wire R-20 (1.0 mm) Former RH 1.0 Wire R-23 (0.8 mm) Former RH 0.8 Wire R-25 (0.6 mm) Former RH 0.6 Wire (1.0 mm) Driver 1.0 Wire (0.8 mm) Driver 0.8 Wire (0.6 mm) Driver 0.6 Wire Screw M4x0.7x Bearing Slide Washer, DB75VS C Bender Insert-Carbide, DB75VS A Driver Slide Assembly, DB75VS A Bender Slide Assembly, DB75VS G20298 Nylock Lock Nut M6x1 30
32 Cutter Box Assembly G A or A (5/8"/15mm Crown A) (Assembly, includes Roll Pin) (DB75) or (DB75V, DB75VS) G G C CS (Short) A C 31
33 Cutter Box Assembly DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION A Cutter Box Assembly A Cutter Box Assembly Cutter Box Spring Cutter Operating Slide Feed Gear Stop C Fixed Cutter - Carbide CS Fixed Cutter - Carbide-Short Lock Washer Ribbed, M Lock Washer Ribbed, M C , Moving Cutter - Carbide G20520 Ribbed Lock Washer, M6 G Screw M4x0.7x10, Nylon G Screw M4x0.7x Screw M4x0.7x12 LH Washer Screw M6x1.0x30 G Screw M6x1x12, Nylon Spring Pin, M5x A Wire Straightener Assembly 32
34 Feed Gear Assembly - DB75, DB75V & DB75VS A * * s.a.e. oil (Assembly, includes ) (FOR DB75 ONLY) A * (FOR DB75V ONLY) A * aero shell USE REPLACEMENT KIT MMKFG1 FOR DB75 AND HK75. USE REPLACEMENT KIT MMKFG2 FOR DB75V, DB75VS, HK75V, AND HK75VS (DB75V) or (DB75) Used together replaces Feed Gear Assembly - DB75, DB75V & DB75VS DELUXE PART NUMBER MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Grooved Pin DB Feed Gear Clutch E-Ring Extension Spring Feed Gear Operating Lever Assy A DB Feed Gear, Large * Indicates parts that are not interchangeable with Müller-Martini parts. All parts used together can be used interchangeably with the HK75 or HK75V. 33
35 Wire Holder Assemblies; DB75 & DB75V Complete Assembly A DB75VS Complete Assembly A 5/8"/15mm Crown A DELUXE PART NUMBER Wire Holder Assembly MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION DB Head Wire Holder Screw M3x0.5x E-Ring Extension Spring Wire Hook DB Head Wire Holder Hook Pivot Pin Wire Holder Hook Assembly, VS Screw M3x0.5x Extension Spring SHADED PART NUMBERS DENOTES WEAR PARTS 34
36 Clincher Plate Assemblies SHADED PART NUMBERS DENOTES WEAR PARTS *(When using solid clincher plates remove moveable slide & points.) or C (Carbide) A A (2) (w/ Pins installed) * (Optional Solid Clincher) "Safety Stitch" (2) B * * (Optional Solid Clincher) "Safety Stitch" (2) (2) OR B (Optional Solid Clincher) "Safety Stitch" (2) (2) (2) or C (Carbide) C G20520 (2) CARBIDE - HEAVY DUTY "OPTIONAL" G20520 (2) (2) G20520 (2) (2) (2) 2.0in 50mm 2.6in 65mm 4.8in 122mm 5.3in 135mm 4.1in 103mm 4.2in 108mm Standard Clincher Plate Used on Bravo/Prima machines After 2004, used on all Optima & Supra machines Used on all Presto & Valore machines Used on Minuteman (1509) machinesbuilt after Jan
37 Clincher Plate Assemblies ( ) or C (Carbide) ( CAR) DELUXE PART MÜLLER PART NUMBER PART NUMBER CROSS REFERENCE DESCRIPTION Clincher Slide Assembly Clincher Mounting Bar Plate Insert Clincher Back Plate Clincher Front Plate Screw M6x1.0x Clincher Point 1/ C Clincher Slide Assembly, Carbide G Lock Washer Ribbed, M6 DELUXE PART NUMBER A ( ) MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Clincher Back Plate, Bravo Plus Clincher Front Plate, Bravo Plus Clincher Slide, Carbide, Bravo Plus 5-5/16-135mm Clincher Mounting Bar, Bravo Plus Lock Washer, Ribbed M Screw, M6x1.0x14, SHC Screw, M5x0.8x10, SHC Low Head Clincher Point 1/ B Solid Clincher Plate Insert, Bravo & Primo 2004 or Newer G20520 Lock Washer Ribbed, M6 DELUXE PART NUMBER A ( ) MÜLLER PART NUMBER CROSS REFERENCE PART DESCRIPTION Solid Clincher Plate Insert Clincher Back Plate, Medium Length Clincher Front Plate, Medium Length Clincher Slide Assy., Medium Length C Clincher Slide Assy., Carbide, 108mm Long Clincher Mounting Bar Screw, M6x1.0x8, FHM Screw M6x1.0x Clincher Point 1/ B Solid Clincher Plate Insert, Bravo & Primo 2004 or Newer 36
38 NOTES: 37
39 DeLuxe Stitcher / Müller Part Number Cross-Reference Supporter Block, 15mm Crown Centering Guide, 15mm Crown Supporter, 15mm Crown Grooved Pin Feed Cam Compression Spring Bonnet - DB A DB Feed Gear Pinion Assembly Feed Gear, Small Feed Gear Shaft Feed Release Cam Assembly Feed Release Handle A Wire Holder Assembly Wire Tube C Moving Cutter - Carbide A Driver Slide Assembly Driver Wire Driver Wire Driver Wire A Bender Slide Assembly Upper Wire Tube Wire Holder Retaining Spring Friction Strip A Cutter Box Assembly Cutter Operating Slide A Wire Straightener Assembly Cutter Box Spring Cutter Operating Lever Wire Tube Clamp Wire Guide Spring Supporter Spring Bonnet - DB75V A DB Feed Gear, Large A DB Feed Gear Pinion Assembly DB Feed Gear Clutch Lower Wire Tube L Former LH Wire L Former LH Wire L Former LH Wire R Former RH Wire R Former RH Wire R Former RH Wire A Driver Slide Assembly Driver Wire Driver Wire Driver Wire Supporter A Wire Holder Assembly, DB75VS A Bender Slide Assembly Wire Holder Retaining Spring A Cutter Box Assembly Cutter Operating Slide C Fixed Cutter - Carbide CS Fixed Cutter - Carbide-Short R Former RH Wire R Former RH Wire R Former RH Wire L Former LH Wire, 15mm Crown L Former LH Wire, 15mm Crown L Former LH Wire, 15mm Crown Driver Wire-15mm Crown Driver Wire-15mm Crown Driver Wire-15mm Crown A Wire Holder Assy, 15mm Crown A Bender Slide Assembly A Cutter Box Assy, 15mm Crown A Clincher Plate Assy., Carbide Clincher Back Plate, Bravo Clincher Front Plate, Bravo Clincher Slide, Carbide, Bravo Clincher Mounting Bar, Bravo A Clincher Plate Assy., Presto Clincher Back Plate, Presto Clincher Front Plate, Presto Clincher Slide Assy., Presto C Clincher Slide Assy., CARBIDE, 108mm Clincher Mounting Bar, Presto Screw, M6x1.0x8, FHM Washer, Large Washer, Shim Ribbed Lock Washer, M Lock Washer, Ribbed Lock Washer Ribbed, 4mm Lock Washer, Ribbed Lock Washer Ribbed, 3.5mm Washer Screw M4x0.7x Screw M4x0.7x Screw M6x1.0x Screw M6x1.0x Screw M6x1.0x30 38
40 DeLuxe Stitcher / Müller Part Number Cross-Reference Screw M5x0.8x Screw M3x0.5x Screw M3x.5x Screw M4x0.7x Screw M4x0.7x Screw M6x1.0x Screw M6x1.0x Screw M4x0.7x12 LH Driver Retaining Screw Screw M4x0.7x Screw M5x0.8x Screw M4x0.7x Screw M4x0.7x Screw, M6x1.0x14, SHC Screw, M5x0.8x10, SHC Low E-Ring E-Ring Cotter Pin Spring Pin, M5x Spring Pin, M3x Spring Pin, M3x Spring Pin, M3x Spin Rivet Hook Pivot Pin, Nylon Dowel Pin, M6x Dowel Pin, M6x Extension Spring Extension Spring Center Guide Spring Compression Spring Feed Gear Operating Lever Assy Centering Guide Post Centering Guide Driver Slide Shaft B Mounting Strap Set Collar Feed Cam Plunger Feed Cam Plunger Bushing Hook Guide, DB Bender Slide Insert Wire Hook Clincher Slide Assembly Clincher Point 1/ Clincher Mounting Bar Solid Clincher B Solid Clincher Optional Clincher Back Plate Clincher Front Plate Supporter Block Centering Guide, Wide Centering Guide, Narrow Hook Guide, DB75V B Hook Guide, 15mm Crown Wire Holder Guide B Wire Holder Guide, 15mm Crown Feed Gear Stop B Mounting Strap, DB75V C Clincher Slide - Carbide Clincher Plate Assy C CAR Clincher Plate Assy-Carbide Bearing, Mount Shaft Bearing, Bender/Driver Bar Bearing, Small Gear Shim Washer Shim Washer Shim Washer Feed Cam Plunger Bushing C Bender Slide Insert-Carbide Hook Guide A Small Feed Gear Asy (Combine) '' Small Gear Bearing (Combine) A Feed Release Cam Assembly C Cutter Operating Lever-Carbide A Driver Slide Assembly A Bender Slide Assembly G Screw M6x1x8 G Screw M6x1x12 G Wire Oiler Felt Spring G Wire Oil Felt Washer G Wire Oiler Felt G Screw M6x1x40 G Hex Nut M6x1 G20360 Hex Key Wrench 3.0mm G20361 Hex Key Wrench 2.5mm G20362 Clamp Wrench 5.0mm G20373 Hex Key Wrench 4.0mm G Lock Washer Ribbed, 6mm G Screw M4x0.7x10 MMKFG1 (See page 28) Müller Feed Gear Kit MMKFG2 (See page 28) Müller Feed Gear Kit 39
41 Please take a moment to fill out the attached card and mail it to DeLuxe Stitcher Company, Inc.. In addition, duplicate the information for your records to assist when making further inquiries. PRODUCT Machine(s) Purchased : Serial Number(s) : With Head(s) : ( Type/Quantity Purchased ) Serial Number(s) : Head(s) Purchased : Serial Number(s) : DE LUXE STITCHER GRAPHIC ARTS REPRESENTATIVE Date Received : Dealer Name : Dealer Street Address : City : State/Province : Zip : Country : Dealer Phone : REGISTRATION To better service your wire stitching needs, please take a moment to fill out and return this registration card. Name : ( First ) ( Middle Initial ) ( Last ) Company : Street Address : City : State/Province : Zip : Country : Phone : Fax : Machine(s) Purchased : Serial Number(s) : With Head(s) : ( Type/Quantity Purchased ) Serial Number(s) : Head(s) Purchased : Serial Number(s) : Date Received : Dealer Name : Dealer Street Address : City : State/Province : Zip : Country : Dealer Phone : Other Bindery Products Used : Would you like information sent to you about new products that would benefit your company? Yes No DEALER PRODUCT CUSTOMER
42 Common Replacement Parts for 1/2 Crown Below is a list of the most common wear/replacement parts for the DB75 and 75V Stitcher Head. This guide should help you when ordering replacement parts. If the part you need is not listed below, please refer to the more detailed parts list on pages Description Item Number Moving Cutter - Carbide C Driver (DB75) or Wire Holder Retaining Spring Cutter Operating Lever Fixed Cutter - Carbide C Moving Cutter Screw Screw, M4x0.7x6-Nylon Rivet Hook Pivot Pin, Nylon Wire Holder Spring Hook Guide Bender Slide Insert Clincher Slide Assembly Clincher Point 1/ Clincher Point Pivot DeLuxe Stitcher COMPANY, INC N Acorn Lane Franklin Park, IL U.S.A. Attn: Customer Service PLACE STAMP HERE
43 LIMITED WARRANTY DeLuxe Stitcher Company, Inc. warrants to the original retail purchaser that this product is free from defects in material and workmanship and agrees to repair or replace, at DeLuxe Stitcher s option, any defective product within 90 days from the date of purchase. This warranty is not transferable. It covers damage resulting only from defects in material or workmanship and does not cover conditions or malfunctions resulting from normal wear, neglect, abuse or accident. This warranty is in lieu of all other express warranties. Any warranty of merchantability or fitness for a particular purpose is limited to the duration of this warranty. DeLuxe Stitcher shall not be liable for any incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service you must return the product, at your expense, together with proof of purchase to an authorized DeLuxe Stitcher Company Graphic Arts Dealer.
44 DELUXE STITCHER ISP Stitching & Bindery Products C O M P A N Y I N C Acorn Lane Franklin Park Illinois Phone: Fax: DBS75HD_0415
Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75, DB75V & DB75VS OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75, DB75V & DB75VS OPERATION AND MAINTENANCE MANUAL DB75HD231/2...Stitcher Head...23
More information(make/model of machine) DB75V Loop OPERATION AND MAINTENANCE MANUAL. DB75VHD231/2L...Stitcher Head...23 Wire
DELUXE STITCHER COMPANY INC. solving your wire stitching needs for 125 years... Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75V Loop OPERATION AND MAINTENANCE MANUAL
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75 & DB75V OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75 & DB75V OPERATION AND MAINTENANCE MANUAL DB75HD231/2...Muller-Martini Head...23
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) DB45 Stitcher Head OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB45 Stitcher Head OPERATION AND MAINTENANCE MANUAL Wire Sizes: 25-28 Ga. Round Crown
More informationWhere Installed: (make/model of machine) G5 Stitcher Head OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER COMPANY INC. solving your wire stitching needs for 125 years... Head Serial Number : Date Purchased : Where Installed: (make/model of machine) G5 Stitcher Head OPERATION AND MAINTENANCE
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) G5 Stitcher Head OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) G5 Stitcher Head OPERATION AND MAINTENANCE MANUAL Wire Sizes: 25-28 Ga. Round Crown Sizes:
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) G20 Stitcher Head OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) G20 Stitcher Head OPERATION AND MAINTENANCE MANUAL Wire Sizes: 23-28 Ga. Round and 21x25
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) G20 Stitcher Head OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) G20 Stitcher Head OPERATION AND MAINTENANCE MANUAL Wire Sizes: 23-28 Ga. Round and 21x25
More informationTable of Content. Machine Features and Functions. Specifications. Configuration and Working Principle 5. Machine Operation. Machine Adjustments
Table of Content Safety Instructions Machine Features and Functions Specifications 2 3 4 Configuration and Working Principle 5 Machine Operation 7 Machine Adjustments 8 Machine Installation 9 Machine Remove
More informationManual Carton Closing Staplers
Operator s Manual Manual Carton Closing Staplers SHB00-A Item No. 6400 -/8" Crown Carton Closing Stapler 5/8" and /4" (5mm and 8mm) Ask for Genuine INTERCHANGE A58 and A4 Staples SHB50-C Item No. 640 -/4"
More informationConforms to OSHA requirements in the U.S.A. FOR INSTALLATION / MAINTENANCE/ ADJUSTMENT IDEAL STITCHER DIVISION W.R.PABICH MANUFACTURING COMPANY INC.
WIDE CROWN STITCHER 1 38 INCH CROWN.037 x.074 WIRE OPERATING INSTRUCTIONS AND PARTS MANUAL Conforms to OSHA requirements in the U.S.A. FOR INSTALLATION / MAINTENANCE/ ADJUSTMENT IDEAL STITCHER DIVISION
More informationPEXTO NO. 137 & NO. 152 FOOT SQUARING SHEAR INSTRUCTIONS AND PARTS IDENTIFICATION
PEXTO NO. 137 & NO. 152 FOOT SQUARING SHEAR INSTRUCTIONS AND PARTS IDENTIFICATION INSTRUCTIONS FOR ADJUSTING PEXTO FOOT SHEARS -- BEFORE OPERATING -- Remove Shears From Skids and Log in Place 1. This shear
More informationSawStop. T-GlideTM. Fence System- Professional Series II OWNER S MANUAL
SawStop T-GlideTM Fence System- Professional Series II OWNER S MANUAL Warranty SawStop warrants to the original retail purchaser of a new T-Glide Fence System - Professional Series II from an authorized
More informationINSTRUCTIONS AND PARTS LIST. Nos. 3D AND 4 V-BELT BOSTITCH WIRE STITCHERS
INSTRUCTIONS AND PARTS LIST FOR THE Nos. 3D AND 4 V-BELT BOSTITCH WIRE STITCHERS When in need of Parts or Service Contact Your BOSTITCH Distributor. You will find "BOSTITCH" listed in phone books of most
More informationSawStop. Contractor Fence Assembly OWNER S MANUAL. Model CNS-SFA
Contractor Fence Assembly OWNER S MANUAL Model CNS-SFA Warranty warrants to the original retail purchaser of the Contractor Fence Assembly accompanying this manual that the fence assembly will be free
More information52/8 04/2005 UNIVERSAL. Narrow Stitching Head. Operating-Instructions Spare parts list
Operating-Instructions Spare parts list UNIVERSAL 52/8 04/2005 Narrow Stitching Head hohner Maschinenbau GmbH Gänsäcker 19, 78532 Tuttlingen, Telephone 07462 / 9468-0, Fax 07462 / 9468-20 hohner Maschinenbau
More informationMANUAL PLASTIC STRAPPING TOOL MODEL P404
OPERATION MANUAL / SPARE PARTS LIST MANUAL PLASTIC STRAPPING TOOL MODEL P404 43.0404.02 43040402.en/MAS/ 12.05 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 TECHNICAL DATA 3 3 OPERATION ELEMENTS 4 4 ADJUSTMENT
More informationOperating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table
Operating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140780 Ph.: 800-274-6848 Revision B1 05/2014 www.jettools.com Copyright
More informationCAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein.
CAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein. All persons involved in such installation, operation, and
More informationModel Assembly & Operating Instructions
30 SHEAR BRAKE ROLL Model 05907 Assembly & Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationOwner s Manual ODYSSEY BENCH MODEL. O4100B shown REV E. Southern Avenue, Phoenix, AZ USA Workhorseproducts.
Owner s Manual ODYSSEY BENCH MODEL O4100B shown 67-1375 REV 218 3730 E. Southern Avenue, Phoenix, AZ 85040 USA 800-778-8779 Workhorseproducts.com 1 Table of Contents I. Introduction & Safety Information.
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationOwner s Manual LSP38 38 Lawn Sweeper
Owner s Manual LSP38 38 Lawn Sweeper Manual Contents Safety Instructions Assembly Operation Maintenance Parts Warranty 2 4-13 2 11 14-15 16 Your Lawn Sweeper Congratulations on your purchase of a new Precision
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #1002493 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C3 02/2014 www.jettools.com
More informationPneumatic Carton Closing Staplers
Operator s Manual Pneumatic Carton Closing Staplers SAB100-A Item No. 640 1-/8" Crown Carton Closing Stapler 5/8" and /4" (15mm and 18mm) Ask for Genuine INTERCHANGE A58 and A4 Staples SAB150-C Item No.
More informationMortising Attachment
Mortising Attachment Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationMODEL T " SPIRAL CUTTERHEAD INSTRUCTIONS
MODEL T10125 6" SPIRAL CUTTERHEAD INSTRUCTIONS The Model T10125 spiral cutterhead is designed to replace the straight knife cutterhead on the Model G0452 6" jointer. The total procedure of changing the
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationMaintenance & Parts list for:
Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide
More informationOperating, Servicing, and Safety Manual Model " Foot Shear CAUTION: Read and Understand
Operating, Servicing, and Safety Manual Model 3000 52" Foot Shear CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. SAFETY The purpose of the
More informationDairy Cap Chuck. Service & Installation Instructions. An Altra Industrial Motion Company P-2021-WE
Dairy Cap Chuck P-2021-WE Service & Installation Instructions An Altra Industrial Motion Company Setting Application Torque 1. Determine initial clutch setting from torque chart below. Recommended Maintenance
More informationRojek Woodworking Machinery Interchangeable Shaper Spindle Installation and User s Guide
Rojek Woodworking Machinery Interchangeable Shaper Spindle Installation and User s Guide Part #: ROJ-PUB-IS-SPINDLE Ver #: 0311 Contents Section 1: Introduction...5 Safety Instructions... 5 Delivered Components
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More information20 Ton HYDRAULIC SHOP PRESS
20 Ton HYDRAULIC SHOP PRESS Stock Number W41063 OWNER S MANUAL WARNING! It is the owner and/or operators responsibility to study all WARNINGS, operating, and maintenance instructions contained on the product
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
More informationMODEL NO. U412 UNIVERSAL BOX AND PAN BRAKE OPERATION, PARTS & MAINTENANCE MANUAL
MODEL NO. U412 UNIVERSAL BOX AND PAN BRAKE OPERATION, PARTS & MAINTENANCE MANUAL Model: Serial #: Purchased From: Date Received: MADE IN THE USA Distributed by: Trick-Tools 80 Truman Road Pella, IA 50219
More informationINSTALLATION & OPERATING INSTRUCTIONS. REDCO LETTUCE KING I and LETTUCE KING IV
INSTALLATION & OPERATING INSTRUCTIONS for REDCO LETTUCE KING I and LETTUCE KING IV Lettuce King I Shown with optional Drum Ring Lettuce King IV TO BE SERVICED ONLY BY AUTHORIZED PERSONS P/N: 2802381 REV:
More informationAssembly Instructions and Parts Manual 5C Collet Closer for GHW Lathes Model CC-GHW
Assembly Instructions and Parts Manual 5C Collet Closer for GHW Lathes Model CC-GHW JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-321519 Ph.: 800-274-6848 Revision G1 03/2014 www.jettools.com
More informationSpecifications. Important Safety Information
Specifications Tire Rim Capacity 4 to 12 Rim Height 16 (2) Bead Breaker Handles 21 Long Includes Aluminum Centering Cone (2) Nylon Spacers Important Safety Information 1. Do not exceed max. tire capacity.
More informationSales and Service
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A333 13.2370.01 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 3 3 APPROPRIATE USE 3 4 TECNICAL DATA
More informationINSTRUCTION BOOK AND PARTS LIST
Rag Cutter MODEL WE WARNING This machine is equipped with a very sharp knife. Keep hands, arms, and hair away from the knife area at all times. Misuse of this machine or failure to follow all safety instructions
More informationMS25 OPERATION MANUAL
SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationTapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
More informationPower Threader BT-5020 Owner s Manual
Power Threader BT-5020 Owner s Manual WARNING! Read this owner s manual before assembling and operating the unit. The moving parts of this unit may cause body injury if it is not proper operated. Always
More informationth St N Oak Park Heights, MN Phone: Fax:
12430 55 th St N Oak Park Heights, MN 55082 Phone: 651.342.1756 Fax: 651.342.1293 Email: info@diacro.com SAFETY INFORMATION PG. 3 MAINTENANCE PG. 3 #4 BENDER BREAKDOWN AND PARTS LIST PG. 4-6 QUIK-LOK BREAKDOWN
More informationCOMBINATION STRAPPING TOOL
AM COMBINATION STRAPPING TOOL READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY. GENERAL SAFETY CONSIDERATIONS 1. STRAP BREAKAGE HAZARD. Improper
More information1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.
Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific
More informationSKID STEER STRAIGHT PLOW
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com SKID STEER STRAIGHT PLOW INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS SAFETY PRECAUTIONS...
More informationPNEUMATIC C-RING TOOLS SC73462 SAFETY INSTRUCTIONS. WARNINGS Always read tool manual before operating.
PNEUMATIC C-RING TOOLS SC73462 SAFETY INSTRUCTIONS WARNINGS Always read tool manual before operating. Always wear safety glasses while operating or while in the vicinity of a tool in operation. For testing,
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationKEEP FOR FUTURE REFERENCE STOWAWAY TILT TABLE READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS TABLE
KEEP FOR FUTURE REFERENCE INSTRUCTIONS International Version P.O. Box 368 908 West Main Laurel, MT USA 59044 phone 800-548-7341 phone 406-628-8231 fax 406-628-8354 MODEL NUMBER: STT1 SERIAL NUMBER: (please
More informationSAFETY INSTRUCTIONS. WARNINGS Always read tool manual before operating.
SAFETY INSTRUCTIONS WARNINGS Always read tool manual before operating. Always wear safety glasses while operating or while in the vicinity of a tool in operation. For testing, always cycle tool away from
More informationMODEL M1023 QUICK CHANGE COLLET ATTACHMENT INSTRUCTION MANUAL. Phone: On-Line Technical Support:
MODEL M1023 QUICK CHANGE COLLET ATTACHMENT INSTRUCTION MANUAL Phone: 1-360-734-3482 On-Line Technical Support: tech-support@shopfox.biz #6727BL COPYRIGHT JANUARY, 2005 BY WOODSTOCK INTERNATIONAL, INC.
More informationOwner s Manual AE PLUG AERATOR MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE Made In CHINA REV
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual AE-48 48 PLUG AERATOR IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. Made In CHINA
More informationAssembly Instructions and Parts Manual 5C Collet Closer for ZX Series Lathes Model CC-ZX
Assembly Instructions and Parts Manual 5C Collet Closer for ZX Series Lathes Model CC-ZX JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-321292 Ph.: 800-274-6848 Revision B 03/2014 www.jettools.com
More informationOPERATION & MAINTENANCE MANUAL
OPERATION & MAINTENANCE MANUAL AUTOMATIC PECAN CRACKER Food Processing Equipment and Machinery Specializing in the Pecan Industry Mailing: PO Box 817, Mansfield, Louisiana 71052 Located: 280 Independence
More informationOperation, Parts and Maintenance Manual Model Notcher
Operation, Parts and Maintenance Manual Model 16-18 Notcher 6926 Smithville Hwy. McMinnville, TN 37110 Phone: 931-934-2211 Fax: 931-934-2220 Email info@tennsmith.com www.tennsmith.com Proudly Made in the
More informationINSTRUCTION SHEET STRUT DRIVER RETROFIT KIT PN: 22-79SDRF
INSTRUCTION SHEET STRUT DRIVER RETROFIT KIT PN: 22-79SDRF COMPONENTS: - Note: Each kit comes with one Strut Driver Gear Case Assembly, one Strut Driver Tube End Adapter Assembly, and a One-Time-Use Threadlocker
More informationSunset Swings By Health in Motion, LLC
Sunset Swings By Health in Motion, LLC Model 421 Lounge Swing Assembly and Operation Manual Record Serial Number Here www.sunsetswings.com by Health In Motion, LLC. 11/6/2009 421 Owners Assembly and Operation
More informationINSTRUCTIONS & PARTS LIST FOR HAND BRAKES
INSTRUCTIONS & PARTS LIST FOR HAND BRAKES MODELS 144-22, 168-22, 192-22, 120-16, 120-14 When ordering repair parts, please refer to the item number, quantity, name of part, part number and serial number
More informationRPR-265. Power Rack (Cage)
ASSEMBLY INSTRUCTIONS 3 3/4" RPR-5 50 3/4" 51 1/4" Power Rack (Cage) TuffStuff Fitness Equipment, Inc. 15 E. Franklin Avenue Pomona, CA 9166, USA Ph: 909-6-1600 Fax: 909-6-496 E-mail: service@tuffstuff.net
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: End User: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating
More informationMANUAL SEALLESS STEEL STRAPPING TOOL MODEL A332
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A332 13.2250.01 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 3 3 APPROPRIATE USE 3 4 TECNICAL DATA
More informationCONCRETE SAW PARTS LIST
CONCRETE SAW PARTS LIST MODEL CCXL-EE December 01 Part # 1 Intentionally Blank Table of Contents Description Page No. Frame Assembly... Carriage Assembly Motor Assembly.... Blade Shaft Assembly... Spring
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts
More informationMANUAL SEALLESS STEEL STRAPPING TOOL MODEL A335
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A335 13.2810.01 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 3 3 APPROPRIATE USE 3 4 TECNICAL DATA
More informationOPERATORS MANUAL WEEKENDER STEEL LADDER RACK
OPERATORS MANUAL WEEKENDER STEEL LADDER RACK WWW.WEATHERGUARD.COM MODELS 1450 & 1475 1475 Shown INSTALLATION TIME Approximate installation time: 60 minutes (depending on truck equipment installation experience
More informationRecord the serial number and date of purchase on your parts list for future reference.
Jointer Model: 0-0 Parts List Record the serial number and date of purchase on your parts list for future reference. Serial number: Date of purchase: Part # 0-0PL For more information: www.rikontools.com
More informationIF YOU DO NOT KNOW WHAT YOU ARE DOING, DO NOT DO IT!
TWIN CAM Alpha & Beta Case Boring Tool The JIMS Twin Cam Case Boring Tool takes all the guess work out of boring Twin Cam engine cases to accept JIMS 4" bore cylinders, 100 big bore kit, and 113" and 116"
More informationATV CULTIVATOR OWNER S MANUAL
ATV CULTIVATOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may
More informationRev B C-RING TOOL VA0375 ½ in. OPERATING MANUAL
Rev B 4-30-0 C-RING TOOL VA0375 ½ in. OPERATING MANUAL Operational Instructions for Vertex C-Ring Tool VA0375 Vertex Fasteners is committed to providing our customers with world-class customer service
More information1801 Ratchet Bender For 1-1/4", 1-1/2" Rigid Conduit, IMC and Schedule 40 Pipe
INSTRUCTION MANUAL 1801 Ratchet Bender For 1-1/4", 1-1/2" Rigid Conduit, IMC and Schedule 40 Pipe Serial Code RS Read and understand all of the instructions and safety information in this manual before
More informationMAGNATEK LOOP STITCH
ISP Stitching & Bindery Products A Division Of Samuel Strapping Systems MAGNATEK LOOP STITCH Supplement Manual For Loop stitchers Serial Numbers 7335K and greater LOOP STITCH BINDERY STITCHING METHOD 1.
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationInstallation Manual Porter Road, Sarasota FL fax
072015 Installation Manual BEFORE YOU BEGIN: Read these instructions completely and carefully. FOR YOUR SAFETY: Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. Risk of injury.
More informationCut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More information3-1/4 HP VARIABLE SPEED PLUNGE ROUTER
IMPORTANT INFORMATION 2-YEAR LIMITED WARRANTY FOR THIS PLUNGE ROUTER KING CANADA TOOLS OFFERS A 2-YEAR LIMITED WARANTY FOR NON-COMMERCIAL USE. 3-1/4 HP VARIABLE SPEED PLUNGE ROUTER PROOF OF PURCHASE Please
More informationCrestline Dampening System. Installation Instructions. Hamada RS34 & VS34 Parent Unit DU34 Upper Unit. For Presses Originally Equipped With
Crestline Dampening System Installation Instructions Hamada RS34 & VS34 Parent Unit DU34 Upper Unit For Presses Originally Equipped With Molleton Dampeners X88-78 01/2001 Rev-A GENERAL INFORMATION ATTENTION
More informationKURT D810 AngLock Vise Base Assembly
KURT MANUFACUTRING - LIFETIME IRONCLAD TM WARRANTY All Kurt Manufacturing Company industrial workholding products and parts with the exceptions noted below, are warranted against defects in material and
More informationGENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationLPK1550 Hydraulic Crimping Tool 15-ton
SERVICE MANUAL LPK1550 Hydraulic Crimping Tool 15-ton Serial Code FYF Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationSales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.
Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)
More informationInstallation Instructions HOSS Hardtop Organized Storage System
Installation Instructions HOSS Hardtop Organized Storage System Application: Hard Top and Doors Storage System Part Number: 42801 www.bestop.com - We re here to help! Visit our web site and click on Ask
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationRATCHET CABLE CUTTER
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 764 RATCHET CABLE CUTTER Read and understand this material before operating or servicing this equipment. Failure to understand how to safely operate this
More informationOperating Instructions and Parts Manual Folding Hydraulic Crane Model: JFHC-200X
This Manual is Bookmarked Operating Instructions and Parts Manual Folding Hydraulic Crane Model: JFHC-200X WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-106206K Ph.: 800-274-6848 Revision
More informationModel DB Disc Caliper Brake AIR CHAMP PRODUCTS. User Manual. (i) MTY (81)
DIST. AUTORIZADO MEX (55) 53 63 3 3 QRO (44) 95 7 60 MTY (8) 83 54 0 8 AIR CHAMP PRODUCTS User Manual Model DB Disc Caliper Brake (i) FORM NO. L-00-G-030 MEX (55) 53 63 3 3 MTY (8) 83 54 0 8 DIST. AUTORIZADO
More informationVideo Wall Installation Instructions 2W X 3H, 3W X 3H
Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...
More informationSERIES I MILLING MACHINES
INSTALLATION, OPERATION, MAINTENANCE, AND PARTS LIST SERIES I MILLING MACHINES TP5260 Revised: August 29, 2005 Manual No. M-450 Litho in U.S.A. Part No. M -0009500-0450 June, 2003 MAINTENANCE PROCEDURES
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
MODEL NO. T8190SA TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More information- INSTALLATION INSTRUCTIONS -
. Supercharger Shaft Upgrade Kit PART# - RY17040-UK-6S5-2 APPLICATION(S): Yamaha FX-SHO, FZR & FZS Required tools Part# IN LB Electronic Torque Wrench N/A T-30 Torx Bit Socket N/A 3mm Allen Wrench N/A
More informationStaple Specification:
H-1027, H-1028 H-3064 PNEUMATIC STICK STAPLER stapler specifications Dimensions: L x H x W 13.5 x 8.75 x 6" Weight (Without Fasteners) Compressed Air: Maximum psi: Recommended Operating Pressure: Air Consumption:
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355
ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
Owner s Manual LSV50120B LS5000B leg bundle LS5021B post bundle LS5022B cradle bundle V50120B straight LS5003B spreader bundle LS5004B bunk bundle LS4005B accessory box LS2005B wheel LS5007B diag bundle
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationSIMPLEX ELITE MAT CUTTER
INSTRUCTION MANUAL MODEL 750-1 / 760-1 SIMPLEX ELITE MAT CUTTER INSTRUCTIONS AND OPERATION MANUAL 40 in (101 cm) mat cutting system with bevel & straight cutters, production stops, 27 in (68 cm) squaring
More information