Remove wallplate and switch mounting screws. Carefully remove switch from wall leaving all wires attached.
|
|
|
- Todd Chambers
- 6 years ago
- Views:
Transcription
1 Using Occupancy Sensing Switch with Maestro Application Note #435 Revision A April Occupancy Sensing Switch LutronR Occupancy & Vacancy motion sensors are passive infrared (PIR) sensors that automatically control lights. These sensors detect the heat from occupants moving within an area to determine when the space is occupied. The sensors then control the lights automatically turning them off or on, providing convenience and increased energy savings.! WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit. 2 Remove wallplate and switch mounting screws. Carefully remove switch from wall leaving all wires attached. 3 Identify switch type (Single pole, 3-way or 4-way) and tag the COMMON terminal. 3A Single pole (One location) Switch will have insulated wires connected to two screws of the same color plus a green ground screw. See Diagram A A Same Color Screws 3B Single Pole 1 Switch controlling 1 Light 3-way (Two locations) 3-way switches will have insulated wires connected to three screws plus a green ground screw. One of these wires is connected to a screw of a different color (not green) or labeled COMMON. Tag this wire on both switches to identify when removing. See Diagram B B Different Color Screw 3-way 2 Switches controlling 1 Light Tag Lutron Technical Support Center
2 3C 4-way (Three or more locations) 4-way switches will have insulated wires connected to four screws plus a green ground screw. Tag either set of two same-color insulated wires that are connected to different-colored screws (on the same side of the switch). Follow this procedure for each 4-way switch. See Diagram C C Same Color 2 Switches will be 3-way, others will be 4-way. Tags Different Color Screws 4-way 3 or more Switches controlling 1 Light. 4 Disconnect wires from the switches removed in step 2. The switches may have two wires attached to the same screw. Tape these two wires together before disconnecting. Screw Terminal Push-in Terminal 5 Connect Occupancy Sensing Switch and es 5A Single pole (One location) - Existing switch will be replaced with an Occupancy Sensing Switch. Connect green and bare ground wire on Occupancy Sensing Switch to bare copper or green wire in wallbox. Connect one of the remaining wires removed from switch to wire on Occupancy Sensing Switch. Connect remaining wire removed from switch to the other wire on Occupancy Sensing Switch. wire is not used in a single-pole circuit. Cap blue wire. Occupancy Sensing Switch 2 Lutron Technical Support Center
3 3-way (Two locations) NOTE: 120 V~ circuits use MA -AS/ MSC-AS es 240 / 277 V~ circuits use MA -AS-277/ MSC-AS-277 es Wire the Occupancy Sensing Switch Connect green and bare ground wire on Occupancy Sensing Switch to bare copper or green wire in wallbox. Connect tagged wire removed from switch to one of the black wires on Occupancy Sensing Switch. Connect one of the remaining wires removed from switch to the other wire on Occupancy Sensing Switch. Connect remaining wire removed from switch (note color) to blue wire on Occupancy Sensing Switch. 5B Occupancy Sensing Switch Wire the Connect green ground wire on to bare copper or green wire in wallbox. Connect tagged wire removed from switch to black screw terminal on. Connect the same color wire connected to the blue wire on Occupancy Sensing Switch (color noted above) to the blue screw terminal on. Connect remaining wire removed from switch to brass screw terminal on. Brass screw screw screw Tag wire See wiring diagrams on next page. 3 Lutron Technical Support Center
4 5B Wiring Diagrams Product Key Switch Type Occupancy Sensing Switch (Wires) Screw Color (120 V~ ) Brass Wire Color (277 V~ ) Wire Wire Wire OR 4 Lutron Technical Support Center
5 5C 4-way (Three or more locations) NOTE: The Occupancy Sensing Switch can be installed in any of the locations (choose the location where the sensor will have optimal coverage of the space). The occupancy sensing switch and/or companion switches can replace a 4-way switch or 3-way switch (4-way applications typically include both 4-way and 3-way switches). Wire the Occupancy Sensing Switch replacing a 4-way switch Connect green and bare ground wire on Occupancy Sensing Switch to bare copper or green wire in wallbox. Connect both tagged wires (note color) removed from 4-way switch to blue wire on Occupancy Sensing Switch. Connect one of the remaining wires removed from switch to one of the black wires on Occupancy Sensing Switch. Connect remaining wire removed from switch to other wire on Occupancy Sensing Switch. Occupancy Sensing Switch Wire the replacing a 4-way switch Connect green wire on to bare copper or green wire in wallbox. Connect both tagged wires (note wire color) removed from 4-way switch to blue screw terminal on Companion Switch (one wire to screw terminal the other to push-in terminal). Connect one of the remaining wires removed from switch to black screw terminal on. Connect remaining wire removed from switch to brass screw terminal on. NOTE: Repeat for each replacing a 4-way switch. Brass screw screw Tags screw wire See wiring diagrams on page 7. 5 Lutron Technical Support Center
6 5C 4-way (Three or more location control) Wire the Occupancy Sensing Switch replacing a 3-way switch Connect green ground wire on Occupancy Sensing Switch to bare copper or green wire in wallbox. Connect tagged wire removed from switch to one of the black wires on Occupancy Sensing Switch. Connect same color wire connected to blue screw terminal on that replaced 4-way switch (color noted above) to blue wire on Occupancy Sensor Switch. Connect remaining wire removed from switch to the other wire on Occupancy Sensing Switch. Occupancy Sensing Switch Wire the (es) replacing a 3-way switch Connect green ground wire on to bare copper or green wire in wallbox. Connect tagged wire removed from switch to the black screw terminal on. Connect same color wire connected to blue wire on Occupancy Sensor Switch that replaced 4-way switch (color noted above) to blue screw terminal on. Connect remaining wire removed from switch to the brass screw terminal on. (See Instructions that came with for more information) NOTE: Repeat for each replacing a 3-way switch. Brass screw screw screw See wiring diagrams on next page. 6 Lutron Technical Support Center
7 5C Wiring Diagrams Product Key Switch Type Occupancy Sensing Switch (Wires) Screw Color (120 V~ ) Brass Wire Color (277 V~ ) Wire Wire Wire 4-way OR 4-way OR 4-way 7 Lutron Technical Support Center
8 6 Push wires carefully into wallbox and install Occupancy Sensing Switch and all es. Leave wall plate off Occupancy Sensing Switch if custom settings are desired. See Occupancy Sensing Switch installation instructions for details on custom settings. 7 Turn power On at circuit breaker. NOTE: Once power has been restored, the Occupancy Sensing Switch can be manually turned on or off after 30 seconds but will not automatically control the load for the first 2 minutes. Lutron Contact Numbers WORLD HEADQUARTERS USA Lutron Electronics Co., Inc Suter Road Coopersburg, PA TEL: FAX: Toll-Free: LUTRON1 Technical Support: product@lutron.com North & South America Technical Hotlines USA, Canada, Caribbean: Mexico: Central/South America: EUROPEAN HEADQUARTERS United Kingdom Lutron EA Ltd. 6 Sovereign Close London, E1W 3JF United Kingdom TEL: +44.(0) FAX: +44.(0) FREEPHONE (UK): Technical Support: +44. (0) lutronlondon@lutron.com ASIAN HEADQUARTERS Singapore Lutron GL Ltd. 15 Hoe Chiang Road #07-03, Tower 15 Singapore TEL: FAX: Technical Support: lutronsea@lutron.com Asia Technical Hotlines Northern China: Southern China: Hong Kong: Indonesia: Japan: Macau: Taiwan: Thailand: Other Countries: Lutron Electronics Co., Inc Suter Road Coopersburg, PA U.S.A. 04/2012 P/N Rev. A
Application Note #463 Revision A July 2012
Revision A July 2012 Pico control of Sivoia QS Wired Shades through a standalone QSM The QS Sens Module (QSM) provides control of Sivoia QS Shades through Pico Wireless controls. This guide lays out the
Application Note #626 Revision A December 2016 Captive Card Key Integration for myroom Prime
LUTRON Application Note #626 Revision A December 2016 Captive Card Key Integration for myroom Prime Captive card key controls can be used in hotel guestroom systems to comply with automatic shutoff requirements*.
Advanced Programming Mode (APM) for Maestro ELV Dimmers
Advanced Programming Mode (APM) for Maestro EV Dimmers Application Note #453 evision D January 2013 Maestro Models MAEV-600 MSCEV-600M Overview The Maestro dimmer features an Advanced Programming Mode
Application Note #622 Revision C April Finiré 3 Design Guide. Overview
Finiré 3 Design Guide Application Note #622 Revision C April 2017 Overview The Finiré 3 fixtures are a diverse product offering that has many potential options that allow them to fit into different applications.
Maestro Occupancy Sensor C L Dimmer Additional Programming, Installation, and Troubleshooting Help
Maestro Occupancy Sensor C Dimmer Additional Programming, Installation, and Troubleshooting Help Maestro Occupancy Sensor C Dimmer Models MSC-OP153M; MSC-OP153MH Application Note #480 evision A January
microos Occupant Sensors One Way microostm Occupant Sensor Two Way microostm Occupant Sensor Sensors
microos Occupant Occupant Sensor microos-1 12.9.03 Lutron s One Way and Two Way microos Occupant enable Lutron systems to change light levels when a space is occupied and/or unoccupied. Occupant sensors
TURN OFF POWER ARRETEZ LE COURANT DESCONECT LA CORRIENTE. Tap Button (tap on/off) Raise Alt. Button Lower. Alt. PIR Hi Med Low Min.
Maestro 0-0 V Sensor Applications Application Note #6 Revision A October 0 This document serves as a supplement to the Maestro 0-0 V Dimmer Sensor Installation Guide for the following model numbers: MS-Z0-XX:
www.electricalsupply.com MaestroR Occupancy Sensor C LR Dimmer LutronR MaestroR occupancy sensor C LR dimmers are lighting controls with passive infrared sensors that automatically control the lights in
Aliante Installation. Components included: Tools required: Not Included:
041137c 1 08.25.16 Important Notes: Please read entire guide before beginning fixture installation. For installation by a qualified electrician familiar with the construction and operation of luminaire
Radio Powr SavrTM Wireless Occupancy / Vacancy Ceiling Sensor
Radio Powr SavrTM Wireless Occupancy / Vacancy Sensor Lutron Radio Powr SavrTM occupancy/vacancy sensors are wireless, battery-powered, passive infrared (PIR) sensors that automatically control lights
Taxonomies, Classifications, and Categories Residential dimmers, motion sensors, controls, & photo cells Wireless occupancy/vacancy sensor
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 LRF20CR2BPWH Lutron Occupancy Sensor 1 Way FM 434 R2 Lutron Catalog Number Manufacturer Description Weight per unit Product
LRF20CR2BPWH Ceiling MNT Wireless Occ Sensor
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 LRF20CR2BPWH Ceiling MNT Wireless Occ Sensor Lutron Catalog Number Manufacturer Description Weight per unit Product Category
Radio Powr SavrT Occupancy / Vacancy Sensor
369480c 1 01.25.13 Radio Powr SavrT Occupancy / Vacancy Sensor LutronR Radio Powr SavrT occupancy/vacancy sensors are wireless, battery-powered passive infrared (PIR) sensors that automatically control
Verifying Power Supply Sequencing with an 8-Channel Oscilloscope APPLICATION NOTE
Verifying Power Supply Sequencing with an 8-Channel Oscilloscope Introduction In systems that rely on multiple power rails, power-on sequencing and power-off sequencing can be critical. If the power supplies
EMI Core ESD-R-H Series Toroidal Cores for Round Cables with High Heat Resistance and Cable Holding Mechanism
EMI Core ESD-R-H Series Toroidal Cores for Round Cables with High Heat Resistance and Cable Holding Mechanism Overview The KEMET ESD-R-H Series split toroidal cores feature high heat resistance and a cable
Automated Frequency Response Measurement with AFG31000, MDO3000 and TekBench Instrument Control Software APPLICATION NOTE
Automated Frequency Response Measurement with AFG31000, MDO3000 and TekBench Instrument Control Software Introduction For undergraduate students in colleges and universities, frequency response testing
CAUTION: To prevent damage to your equipment, thoroughly study all instructions and illustrations before you begin to install the extension.
I N S T R U C T I O N M A N U A L The Christie Vivid extension is an easy to install option designed to provide quick height adjustment for your installation needs. This extension can be secured to ceilings
Installation Instructions
TECH SUPPORT The Watt Stopper, Inc. 2800 De La Cruz Blvd. Santa Clara, CA 95050, USA Tel: 1(800)879-8585 1(972)578-1699 Fax: 1(972)422-1311 www.wattstopper.com Outdoor 180 & 270 PIR Motion s Model#s: EW-100-120
1SS/1S1/1SM SUB-MINIATURE ROCKERS
SS/S/SM S-Series SUB-MINIATURE ROCKERS The S family of sub-miniature rocker switches is composed of three switch series; the S-Series sub-miniature rocker switch, the SS-Series sealed sub-miniature rocker
Snap-on convenience Split construction Temperature Index of 65 C Meets the requirements of UL94V-0 CTI: Rank 0 Broad range by simply adding turns
EMI Cores ESD-SR Series Snap-on Cores for Round Cables Overview KEMET ESD-SR Series snap-on cores are designed for use on round cable and are available in a variety of sizes. EMI cores are part of a family
Overview. Applications. Benefits. Ordering Information. Sensors High Alternating Current Sensors, Snap-on Type
Sensors High Alternating Current Sensors, Snap-on Type Overview The C/CT-1216 clamp-on current sensor can be used to measure currents in live wires. Applications Typical applications include EMS current
PowPak Dimming Module with. EcoSystem. PowPak Dimming Module Energi TriPak Series Wireless Lighting Control
PowPak Dimming Module with 369427j 1 08.19.16 The PowPak Dimming Module with is a radio frequency (RF) control that operates up to 32 Ballasts / LED drivers based on input from controls and Radio Powr
www.greenelectricalsupply.com Wireless Wall-Mount Sensor Lutron wall-mounted occupancy and vacancy sensors are wireless, battery-powered, passive infrared (PIR) sensors that automatically control lights
LCP128TM Dimming and Switching System
Please ead CP128TM Dimming and Switching System Installation Guide Table of Contents Step-by-Step Instructions Page Step 1: Panel Dimensions...............................................................4
EMI Core ESD-SR-H/HL Series Snap-on Cores for Round Cables with High Heat Resistance and Cable Holding Mechanism
EMI Core ESD-SR-H/HL Series Snap-on Cores for Round Cables with High Heat Resistance and Cable Holding Mechanism Overview The KEMET ESD-SR-H/HL Series snapon cores feature high heat resistance and a cable
ETC Installation Guide
Unison Echo Overview The Echo is a ceiling mounted sensor that utilizes passive infrared (PIR) technology, providing reliable vacancy and occupancy detection for lighting control. The sensor allows for
PowPak CCO Module. PowPak CCO Module Energi TriPak Series Wireless Lighting Control
PowPak CCO Module 369433g 1 07.21.16 The PowPak CCO Module is a low-voltage radio frequency (RF) control that provides a single dry contact closure output based on input from Pico controls and Radio Powr
Lutron tensioned shade (4.75 inch frame) Chassis Installation Instructions
Lutron tensioned shade (4.75 inch frame) Chassis Installation Instructions Lutron tensioned shade (4.75 inch frame) The Tensioned Shade Chassis Installation Guide is a complement to the enclosed Basic
Tire Pressure Monitoring Systems and Remote/Passive Keyless Entry
Tire Pressure Monitoring Systems and Remote/Passive Keyless Entry Introduction Today, more sophisticated and sensitive RF electronic components and devices are being included in automobiles. These advances
ELCO Series 8005/8015 A KYOCERA GROUP COMPANY
Series 8005/8015 A KYOCERA GROUP COMPANY Series 8005 Position Miniature IDC Wire to Board Connector Series 8005 is a super compact pin Wire to Board connector designed for high density mounting. This is
PowPak Relay Module. PowPak Relay Module Energi TriPak Series Wireless Lighting Control
PowPak Relay Module Energi TriPak Series Wireless Lighting Control PowPak Relay Module 369549c 1 10.07.14 The PowPak Relay Module is a radio frequency (RF) device capable of controlling up to 5 A of general-purpose
EMI Core ESD-FPD-1 Series Split Cores with Plastic Clamp for Flat Cables. Split construction Nylon clamp
EMI Core ESD-FPD- Series Split Cores with Plastic Clamp for Flat Cables Overview The KEMET ESD-FPD- Series split cores are designed for use on flat cable. The series features a nylon clamp and is available
MPLCH 0740 L 1R0. Series Size L x W (mm) Inductor Inductance Code µh MPLCH
Large-Current Power MPLCH Series Overview KEMET s MPLCH Series of metal composite inductors is ideal for use in DC to DC switching power supplies. The combination of composite core material and round wire
PowPak Dimming Module with. EcoSystem. PowPak Dimming Module Energi TriPak Series Wireless Lighting Control
PowPak Dimming Module with 369427g 1 07.18.13 The PowPak Dimming Module with is a radio frequency (RF) control that operates up to 32 Ballast / LED drivers based on input from controls and Radio Powr Savr
Using the 4200A-CVIV Multi-Switch to Make High Voltage and High Current C-V Measurements APPLICATION NOTE
Using the 4200A-CVIV Multi-Switch to Make High Voltage and High Current C-V Measurements Introduction Traditional capacitance-voltage (C-V) testing of semiconductor materials is typically limited to about
www.greenelectricalsupply.com Radio Powr SavrT Wireless Occupancy / Vacancy Ceiling Sensor LutronR Radio Powr SavrT occupancy/vacancy sensors are wireless, battery-powered passive infrared (PIR) sensors
Applications SCF Type Dimension Code (See Table 1) Rated Current (A) Minimum Inductance (mh)
AC Line Filters SC Coils, SCF Compact, High-inductance Type Overview The KEMET SC Coils, SCF Compact, High-inductance Type AC line filters are offered in a wide variety of sizes and specifications. Applications
Applications SCR R55 A250 JH
AC Line Filters SCR Coils, High Impedance Type Overview The KEMET SCR Coils, High Impedance Type AC line filters feature a newly developed, high permeability core. Applications Audio-visual Equipment Consumer
SCXI High-Voltage Terminal Block
INSTALLATION GUIDE SCXI -326 High-Voltage Terminal Block Introduction This guide describes how to use and install the SCXI-326 high-voltage terminal block with the SCXI-62, the SCXI-63, the SCXI-62HV,
CONTENTS OF THE BOX. *PIR sensor only **Dual Technology and PIR sensors only. Description PIR Ultrasonic Dual Technology
Instruction Bulletin 63249-420-283A4 08/2009 Wall Mount Occupancy Sensor SLSWPS1500, SLSWUS1500, SLSWDS1500 INTRODUCTION Wall Mounted Occupancy Sensors are Class 2 devices ideal for use in business or
Multi-location. Dimmer. Accessory Dimmer. 4-Scene IR Hand-held Remote Control. 23mm (0.91 ) 48mm (1.89 ) 2.8mm (0.11 ) 10mm (0.39 ) 11.6mm (0.
367059 5/29/02 10:00 AM Page 1 SPECIFICATION SUBMITTAL Advanced technology in an easy-to-use dimmer. CONTROLS AND ACCESSORIES www.lutron.com/telume Multi-location Multi-location with IR Receiver Accessory
Applications PHZ9004 E F 7100 M R06L2
AC Line EMI Suppression and RC Networks PHZ9004 Series Metallized Polypropylene Film, 300 VAC 3x X2 with Separate Terminals for Three-Phase Filtering Overview The PHZ9004 Series is constructed of metallized
P7500 Series Probes Tip Selection, Rework and Soldering Guide
How-to-Guide P7500 Series Probes Tip Selection, Rework and For Use with Memory Component Interposers P7500 Series Probe Tip Selection, Rework and for Use with Memory Component Interposers Introduction
Applications SC JH
AC Line Filters SC Coils, SC-JH Terminal Base Type Overview The KEMET SC Coils, SC-JH Terminal Base Type AC line filters are offered in a wide variety of sizes and specifications. Applications Consumer
MRF21S8A10C Energy Retrofit Package
MRF21S8A10C Energy Retrofit Package Lutron Catalog Number MRF21S8A10C Manufacturer Lutron Description Energi Tripak Package, Includes: 1 Maestro Wireless 8A No Neutral Switch, 1 Claro 1-Gang Faceplate,
Simplifying FET Testing with 2600B System SourceMeter SMU Instruments APPLICATION NOTE
Simplifying FET Testing with 2600B System SourceMeter SMU Instruments Introduction Field effect transistors (FETs) are important semiconductor devices with many applications because they are fundamental
Applications SU 16 VD
AC Line Filters SU Coils, SU 1VD High Frequency Type Overview The KEMET SU Coils, SU 1VD High Frequency Type AC line filters are offered in a wide variety of sizes and specifications. Applications Consumer
ERM-DA. Installation Guide
ERM-DA Installation Guide ERM-DA Product Overview Echoflex s ERM-DA is an active circuit transmitter that provides a low cost method of using a live electrical circuit as a switch. When the circuit is
Simplifying DC-DC Converter Characterization using a 2600B System SourceMeter SMU Instrument and MSO/DPO5000 or DPO7000 Series Scope APPLICATION NOTE
Simplifying DC-DC Characterization using a 2600B System SourceMeter SMU Instrument and MSO/DPO5000 or DPO7000 Series Scope Introduction DC-DC converters are widely used electronic components that convert
Applications SS 30 V- R
AC Line Filters SS Coils, SS0V Type Overview The KEMET SS Coils, SS0V Type AC line filters are offered in a wide variety of sizes and specifications. Applications Consumer Electronics Common mode choke
Applications SU 10 VFC- R
AC Line Filters SU Coils, SU VFC-R Type Overview The KEMET SU Coils, SU VFC-R Type AC line filters are offered in a wide variety of sizes and specifications. Applications Consumer Electronics Common mode
Using the Model 4225-RPM Remote Amplifier/ Switch to Automate Switching Between DC I-V, C-V, and Pulsed I-V Measurements APPLICATION NOTE
Using the Model 4225-RPM Remote Amplifier/ Switch to Automate Switching Between DC I-V, C-V, and Pulsed I-V Measurements Characterizing a device, material, or process electrically often requires performing
30 A AC/DC Current Probe TCP0030A Datasheet
30 A AC/DC Current Probe TCP0030A Datasheet Split-core construction allows easy circuit connection High accuracy with typically less than 1% DC gain error Low noise and DC drift 3rd party safety certification
AbellaTM and CeanaTM. dimmers and switches. effortless transition to your perfect light
AbellaTM and CeanaTM dimmers and switches effortless transition to your perfect light style and convenience Coordinate the look of lighting control throughout your home while selecting the features you
Inigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
Measuring Vgs on Wide Bandgap Semiconductors APPLICATION NOTE
Measuring Vgs on Wide Bandgap Semiconductors This application note focuses on accurate high-side V GS measurements using the IsoVu measurement system. The measurements described in this application note
1204 Reflected Wave Reduction Device
Instructions 1204 Reflected Wave Reduction Device (Catalog Number 1204-RWR2-09-B, C) This publication will guide you through installation (including mounting, wiring and grounding procedures) of the 1204
Installation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co.
Installation and Operation Manual Ajustable Valance Kits 2502757 2502857 : Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2018
GV3000 AC General Purpose (Volts/Hertz) and Vector Duty Drive
Software Start-Up and Reference Manual D2-3339-1 GV3000 AC General Purpose (Volts/Hertz) and Vector Duty Drive Version 5.0 Important User Information Solid-state equipment has operational characteristics
PowPak Relay Module with Softswitch
PowPak Relay Module with Softswitch The PowPak Relay Module with Softswitch is a radio-frequency (RF) device that uses Lutron patented Softswitch technology to control general-purpose loads based on input
Japan s Leading Exhibition for Robotics Technologies Jan. 17[Wed]-19[Fri], 2018 Tokyo Big Sight, Japan
![Japan s Leading Exhibition for Robotics Technologies Jan. 17[Wed]-19[Fri], 2018 Tokyo Big Sight, Japan](/thumbs/78/76786007.jpg "Japan s Leading Exhibition for Robotics Technologies Jan. 17[Wed]-19[Fri], 2018 Tokyo Big Sight, Japan")
Japan s Leading Exhibition for Robotics Technologies Jan. 17[Wed]-19[Fri], 2018 Tokyo Big Sight, Japan Web: http://www.robodex.jp/en/ POST SHOW REPORT 2018 FACTS & FIGURES 17,186 Visitors 200 Exhibitors
VARISPEED-616G5 OPTION CARD DIGITAL REFERENCE CARD DI-16H2 INSTRUCTIONS
YASKAWA VARISPEED-616G5 OPTION CARD DIGITAL REFERENCE CARD DI-16H2 INSTRUCTIONS Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain for future reference.
ETC Installation Guide
ETC Installation Guide Unison Using this Guide This document is intended to guide you through the installation of the DRd Semi-Recessed installation kit. Reference the Unison DRd Rack Enclosure Installation
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
Debugging SENT Automotive Buses with an Oscilloscope APPLICATION NOTE
Debugging SENT Automotive Buses with an Oscilloscope Introduction Increasingly, automotive designs are adopting Single Edge Nibble Transmission (SENT) protocol for low-cost, asynchronous, point-topoint
Recovery Through Exports: Restoring California s Competitive Position
Recovery Through Exports: Restoring California s Competitive Position Speakers Mark Bernstein, Senior Vice President, MWW Group; Senior Advisor, OnGreen.com Nanette Bouchard, Vice President, Program Management,
ViveT Maestro Wireless Dimmers and Switches
ViveT Maestro Wireless Dimmers and Switches The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers
Dynamo Brushless DC Motor and GreenDriveTM Manual
Dynamo Brushless DC Motor and GreenDriveTM Manual This manual was developed as a guide for use by FIRST Robotics Teams using Controller Part Number 840205-000 in conjunction with the Nidec Dynamo BLDC
PowPak Dimming Module with EcoSystem
PowPak Dimming Module with EcoSystem 369-427f 1 04.03.12 The PowPak Dimming Module with EcoSystem is a radio frequency (RF) control that operates up to 32 EcoSystem ballasts based on input from controls
Process Control Calibration Made Easy with Agilent U1401A
Process Control Calibration Made Easy with Agilent U1401A Application Note This application note explains how the Agilent U1401A with simultaneous source and measure functions eases technicians calibration
A stringent three-month evaluation process based on a balanced and transparent scorecard had been used to determine the winners.
T.A.B. International Pte Ltd 10, Hoe Chiang Road, #14-06 Keppel Tower, Singapore 089315 Tel: (65) 6236 6520 Fax: (65) 6236 6530 www.theasianbanker.com 29 th April, 2013 Press Release OCBC wins Best Trade
Wireless Ceiling Mount Sensor
Wireless Ceiling Mount Sensor Lutron s occupancy and vacancy sensors are wireless ceiling-mounted battery-powered passive infrared (PIR) sensors that automatically control lights via RF communication to
Wireless Ceiling Motion Sensor for Occupancy / Vacancy Detection with integrated diagnostic tools INSTALLATION GUIDE
MOS-21 Wireless Ceiling Motion Sensor for Occupancy / Vacancy Detection with integrated diagnostic tools INSTALLATION GUIDE This guide covers all models of MOS-21 Ceiling occupancy sensor. The MOS-21 product
GV3000/SE AC Drive HP, 460V AC
Hardware Reference, Installation, and Troubleshooting Manual D2-3392-7 GV3000/SE AC Drive 30-200 HP, 460V AC Version 6.07 Important User Information Solid-state equipment has operational characteristics
DAWN TO DUSK SENSOR OWNER S MANUAL
DAWN TO DUSK SENSOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
S&C Scada-Mate Switching Systems Outdoor Distribution Interrupter Replacement 14.4 kv through 34.5 kv
S&C Scada-Mate Switching Systems Outdoor Distribution Interrupter Replacement 14.4 kv through 34.5 kv Instructions for Field Replacement TABLE OF CONTENTS Section Page Section Page INTRODUCTION Qualified
Memory card connectors
Memory card connectors (PCMCIA CONFORMABLE) surface mount 560H SERIES - LIGHTWEIGHT Features The connectors conform to the Japan Electronic Industry Development Association (JEIDA) and Personal Computer
QS Sensor Module QSM Sensor Interfaces
LUTRON LUTRON QS Sensor Module QSM Sensor Interfaces QS Sensor Module The QS Sensor Module (QSM) is a ceiling-mounted device that integrates LutronR wireless and wired sensors and controls through the
Isolation Addresses Common Sources of Differential Measurement Error
By Tom Neville A typical measurement system includes an oscilloscope and an oscilloscope probe that provides the connection between the device under test (DUT) and the oscilloscope. Probe selection is
Occupancy Sensors for High-Bay Applications
Wired for High-Bay Applications for High-Bay Applications 369606b 1 12.08.2017 Features Surface-mount and end-mount models available. 180 and 360 coverage lenses available. Low-voltage, passive infrared
Installation Instructions
Installation Instructions 30 Built-In Wall Oven with Microwave JTP86, JT965 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully
High-Power Series Pneumatic Series Hydraulic Hydraulic Series Valve / Coupler Expansion Locating Pin Hydraulic Unit Manual Operation Accessories
PAT. 937 φ φ 938 939 940 2 4 3 4 5 6 1 4 φφ 941 φφ φ φ 942 VFL 2 00 0-080 - D - H20 - M R φφφφ φφφφ φφφφφ φφφφφ φφφφφ φ φ φ 943 944 φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ φ 945 946 φ φ φ φ φ φ φ φ
SoftswitchTM Technology. One-million-cycle, arcless relay circuit. Technical white paper May 1999 version 1.0
SoftswitchTM Technology One-million-cycle, arcless relay circuit Technical white paper May 1999 version 1.0 Input Power Figure 1 Energy dissipated as Heat into the arc during 'bouncing' I. Introduction
Hi-lume A-Series Driver Overview Forward-Phase Control
LTEA4U1UMN-HC7 Input Entrèe Output Sortie 12 V 38, V Max / 6 Hz,7 A Max,27 A Class 2 32 W Max 27 196 WARNING: Shock hazard. May result in serious injury or death. Disconnect power N before servicing or
Low Capacitance Probes Minimize Impact on Circuit Operation
Presented by TestEquity - www.testequity.com Low Capacitance Probes Minimize Impact on Circuit Operation Application Note Application Note Traditional Passive Probe Advantages Wide dynamic range Inexpensive
PowPak Relay Module with Softswitch
PowPak Relay Module with Softswitch The PowPak Relay Module with Softswitch is a radio frequency (RF) device that uses Lutron patented Softswitch technology to control up to 16 A of general-purpose load
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
FOR RECESSED EDGE-LIT LED EXIT SIGN Standard and New York Approved Models (Emergency, non-emergency and X2 Dual Circuit operation) READ AND FOLLOW ALL SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS: When using
Obsolete Product(s) - Obsolete Product(s)
Dual NPN-PNP complementary Bipolar General features V CE(sat) h FE I C 0.35V >100 1A High gain Low V CE(sat) Simplified circuit design Reduced component count Applications Push-Pull or Totem-Pole configuration
In-circuit Measurements of Inductors and Transformers in Switch Mode Power Supplies APPLICATION NOTE
In-circuit Measurements of Inductors and Transformers in Switch Mode Power Supplies FIGURE 1. Inductors and transformers serve key roles in switch mode power supplies, including filters, step-up/step-down,
FC-SENSOR, FC-VSENSOR, FCJ-010, FCJ-ECO
The PowPak wireless fixture control is a radiofrequency (RF) device that controls either the Lutron EcoSystem or 0 10 V- electronic fluorescent ballasts and LED drivers (depending on model). This is based
Nash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
ETC Installation Guide
Unison Echo Light Sensor Overview The provides light level measurement and lighting control for the connected Echo control system. The sensor measures lighting conditions to maintain a programmed lighting
onlinecomponents.com
FF-SRE609 Extension Module FF-SR Series FEATURES Complies with the Machinery Directive 98/3/EC Meets the applicable parts of the US & Canadian regulations and standards ANSI/RIA/OSHA Redundant and positive-guided
TM-533-T/R TACT Switches
Features: Sharp click feel with a positive tactile feed-back. Due to small movement distance (stroke), user experiences distinct sensation when the switch clicks into place. Ultraminiature and light weight
SCXI CURRENT INPUT,HIGH-VOLTAGE TERMINAL BLOCK
INSTALLATION GUIDE SCXI -1338 CURRENT INPUT,HIGH-VOLTAGE TERMINAL BLOCK Introduction This guide describes how to install and use the SCXI-1338 terminal block with your SCXI-1120, SCXI-1120D, SCXI-1125,
Maybank wins Best Trade Finance Bank and Leading Counterparty Bank in Malaysia for 2012
T.A.B. International Pte Ltd 10, Hoe Chiang Road, #14-06 Keppel Tower, Singapore 089315 Tel: (65) 6236 6520 Fax: (65) 6236 6530 www.theasianbanker.com 29 th April, 2013 Press Release Maybank wins Best
Titan Anxin 安心. RFcamp Ltd. RFID Class1 Gen2. February Unparalleled Robust Metal Mounting Solution. Contents
Titan Anxin 安心 RFID Class1 Gen2 Unparalleled Robust Metal Mounting Solution February 2010 RFcamp Ltd. Contents 1. Intro 2. Main specifications 3. Reliabilities Temp.& humidity 4. Radiation Pattern 5. Reliabilities
Agilent PN 4395-1 Agilent 4395A Network/Spectrum/ Impedance Analyzer Silicon Investigations Repair Information - Contact Us 920-955-3693 www.siliconinvestigations.com ADSL Copper Loop Measurements Product
IMPORTANT WARNINGS AND CAUTIONS!
I N S T R U C T I O N M A N U A L The Christie Vivid Green ceiling mount will suspend your Christie Vivid Green projector in an upright position to compliment conference rooms, classrooms or home theater
ASSEMBLY AND CARE INSTRUCTIONS CHEER FLOOR 147C/147CC
ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920109 (Revised 10/17) CHEER FLOOR 147C/147CC SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, Oro-Medonte Ontario, Canada L3V