POWER CARVERS/ACCESSORIES

Transcription

1 16 POWER CARVERS/ACCESSORIES Foredom Tools and Accessories Foredom No. 8 handpiece - slim handpiece. Chuck guard sleeve protects fingers and permits close work. Slides back when changing accessories. Includes 3/32 collet and wrenches # $79.00 Foredom No. 30 handpiece - has geared 3-jaw chuck that takes accessory shank sizes up to 5/32. Includes chuck key. 5-1/2 long. # $70.00 No Reversible Kit - Series SR 1/6 hp, ball bearing motor with variable speed up to 18,000 rpm. Electronic foot control. 2 bur holders. No. 44T tapered collet-type handpiece with a maximum capacity of 1/4. Comes with 3/32, 1/8 and 1/4 collets; sanding accessory kit; variety of bits. Includes flexible shaft grease. # $ Foredom No. 44T handpiece - has collet-type chuck adaptable to larger accessories. Includes 1/4 and 1/8 collets with pin & wrench. Has tapered front end. # $66.00 Foredom No. 28 handpiece - comfortable tapered grip and slim, lightweight housing. Includes 1/8 and 3/32 collets. # $66.00 Foredom No. 50C chisel handpiece - converts the rotary motion to a vibration hammer drive for gouges. Includes 6 Foredom gouges. Flexcut reciprocating blades will fit and have a longer shaft. # $83.00 Handpiece w/o chisels #10111-A...$52.00 Replacement sheaths for Foredom Models S, SR, CC, R # $15.00 Replacement internal shafts for Foredom Models S, SR, CC, R, PG # $11.00 Foredom 1070 Micro Motor - operates up to 38,000 RPMs. Unit is manually dialed or foot controlled, variable speed, reversible. Comes with 1/8 collet plus 3/32 adapter. # $ Foredom EMX table-top dial control in plastic case for use with chisel handpiece No. 50C #10114-A...$88.00 Foredom 2 Angle Grinder Attachment for the No. 30 Handpiece (included). Use for broad range of grinding, sanding, polishing and finishing work with 2 and smaller discs. Includes 2 hubs for 3/8 arbor hole wheels, 120 grit flap wheel (installed), disc mandrel, 6 assorted sanding discs, and tools for attaching # $ Small round ivory bur stand with clear plastic lid. Diameter is 2-1/8 x 1-1/2 high. Holds 24 3/32 shanks and 24 1/8 shanks. Small square bur stand with clear plastic lid. Same capacity as round stand (specify round or square) # $4.50 Foredom shaft lube - a high temp. cable grease # $3.50 Shaft lube for Handpiece #50C #10116-A...$4.50 Large rotating bur/ tool holder for all size burs including 1/16, 1/8 and 1/4 shanks. Measures 7 wide by 4 high and holds 69 3/32 or 1/8 burs (in 2-step holes), 12 1/4 burs, and 45 1/16 burs # $17.50

2 POWER CARVERS/ACCESSORIES NSK is the top of the line micromotor unit on the market today - the smoothest running, quietest - preferred by most of the bird carvers. 17 Foredom Model Portable, Brush Type Micromotor Kit Run time is approximately 5 hours, depending on how long the micromotor is in coninuous use - or plug it in for day-long use. Battery charge itme is 3 hours. Has a digital RPM display at the top that makes it easy to monitor speed as you work. Item # $ Optional plastic carrying case Item #10107-C...$50.00 Optional lightweight woven nylon carrying pouch Item #10107-D...$19.00 NSK Emax Evolution Micro Motor - 1,000-40,000 min.; speed control volume with flash load indicator; digital display; soft touch switches permit easy operation; quick collet and bur release system; continuous operation without heat build-up. Item #10193 Call for price. Dust Collector - metal body that has 3 plexiglas shields, creating a funnel to channel the dust to the filter. Has 3 highvolume fans, creating 725 CFM. Two electrical outlets with fan variable speed control. There are recesses in the top to handle a Foredom hanging fixture and a bench light. Weighs 26 lbs. # $ Replacement filter # $ 8.95 Microlux and Merlin MicroLux Gourd/Cross Saw easily cuts through irregular, non-flat objects. The small, rounded shoe permits high maneuverability and keeps the cutting line visible for increased accuracy. Includes allen wrench and 10 coarse blades for soft woods and gourds. Recommend usage with heavy-duty transformer. # $75.15 Pkg. of 10 coarse saw blades # $7.75 Pkg. of 10 fine saw blades # $7.75 Microlux Belt Sander - 12-volt small sander for hand sanding - recommend usage with heavy-duty transformer. Belt is 1 x 9-1/2. # $81.25 Microlux Right Angle Sander - 12-volt disc sander - recommend usage with heavyduty transformer # $92.65 MicroLux 1/4 12 Volt High Torque Drill; 3-jaw keyless chuck from 1/64 to 1/4. Weighs 12 oz. Speed from 1,400/1,500 rpm # $66.90 Merlin2 grinder from King Arthur s Tools - (reengineered 99% more efficient). Proxxon grinder equipped with an 8 tooth chain saw disk, carbide disk, cut-off disk, carborundum metal cutter disk, 60, 120, and 240 grit sanding disks. Unit comes with carrying case # $ inch typhoon cutting disks - blue (EC); red (C); bronze (M); yellow (MF); burgundy (F) # $39.95

3 18 POWER CARVERS/ACCESSORIES Proxxon Proxxon Longneck Angle Grinder - variable speed, includes one aluminum oxide 60 grit disk, one 100 grit fan disk, and one cut-off wheel in case # $ Proxxon Precision Rotary Tool - the smart alternative with keyless chuck, precise vibration-free operation and electronic speed control for continuous variable speeds from 5,000 to 20,000 rpm. Set includes 43 accessories. # $ Proxxon Heavy Duty Transformer NG/5E - 12 volt DC delivers 5 amps with electronic speed control; has capacity for usage of 3 tools at the same time. Will accept both Proxxon and MicroLux tools # $ Proxxon Torch - used for soldering, desoldering, brazing, heating of work pieces and for tinting. Ideal for precision work. Item # $79.00 Proxxon Heavy Duty Jig Saw STS12 - variable speed from 2,000 to 5,000 strokes per minute; includes a standard flat guide foot. Also has rounded foot for gourds. # $ Proxxon Micromot 50/E 12 volt rotary tool weighing 8 oz. with electronic speed control from 5,000 to 10,000 rpms with 6 collets up to 1/8 capacity. # $77.00 Proxxon Regular Transformer NG/2/S - delivers 2 12 volts; will power one tool at a time # $44.00 Proxxon Power Carver MOS takes the work out of your carving project. 10,000 cuts per minute allow for precision carving and delicate work. Quiet, vibration and dust-free operation. Comes with 3 high-quality bi-metallic knives, one each U, V and flat #10464-A...$ Proxxon Complete Model Building and Engraving Set with rotary tool, transformer and a selection of 34 high quality bits. The right choice for creative hobbyists and model makers # $ Proxxon Complete Glass Engraving Set with engraving tool, transformer, trial glass, patterns and all necessary bits to start a wonderful and creative hobby # $68.00

4 STUMP BURS, STONES AND RUBY NITS Stump Burs - 3/32 shafts 19 C212- C212- C212- C212- C213- C213- C213- C213- C214- C214- C214- C214- C215- C215- C215- C C217- C217- C217- F212- F212- F212- F212- F213- F213- F213- F213- F214 F214- F214- F F F F F F F F F C-050/060 C-070/080 F-050/060 F-070/080 $7.50 each $8.70 each $9.50 each $10.25 each Blue Stones - 3/32 shafts --- $3.40 each CK350 CK352 CK302 CK332 CK301 CK300 CK342 CK392 CK390 CK322 White Stones - 3/32 shafts --- $2.30 each W89 W85 W82 W87 W83 W77 W78 W612 Ruby Nits - 3/32 shafts RN11 RN12 RN13 RN14 RN15 RN16 RN31 RN32 RN33 RN34 RN35 RN $ $12.10

5 20 RUBIES, SAPPHIRES AND TYPHOONS Ruby Carvers - 3/32 shafts RC15 - RC $11.50 each RC RC $13.50 each RC $17.95 Super Coarse Rubies - 3/32 shafts SCR $12.45 each SCR $16.90 Sapphires - 3/32 shafts $12.95 each Typhoons Saph 105 Saph 106 Saph 306 A B C D A - Red coarse 1/8 shaft 1/4 ball KB18314 # $17.60 B - Blue fine 3/32 shaft 5/16 ball KB32315 # $25.55 C - Red coarse 1/8 shaft 7/16 ball KB18338 # $17.60 D - Blue fine 1/8 shaft 7/16 ball KB18339 # $17.60 A - Red coarse 1/4 shaft 9/16 ball KB14312 # $20.40 B - Blue fine 1/4 shaft 9/16 ball KB14313 # $20.40 C - Red coarse 1/4 shaft 7/8 ball KB14395 # $23.80 A B C A B C D A B A - Red coarse 3/32 long taper KB32118 # $19.90 A - Red coarse 1/8 bud KB13414 # $17.60 B - Blue fine 3/32 long taper KB32119 # $25.55 B - Blue fine 3/32 cylinder KB32519 # $25.55 C - Red coarse 1/8 flame KB32912 # $17.60 D - Blue fine 1/8 flame KB32913 # $17.60

6 A B C A - Red coarse 1/4 flame small KB14912 # $19.50 B - Blue fine 1/4 flame small KB14913 # $19.50 C - Red coarse 1/4 flame med. KB14958 # $22.00 TYPHOONS AND DIAMONDS Typhoons (continued) A B C A - Red coarse 1/4 cylinder KB14522 # $20.40 B - Red coarse 1/4 x 1 taper KB14158 # $28.00 C - Red coarse 1/4 x 1-3/16 KB14178 # $28.00 Diamond Balls 21 A B A - Red coarse 1/4 ballnose 1-3/4 long KB14714 # $20.40 B - Blue fine 1/4 ballnose 1-3/4 long KB14715 # $20.40 PD26 PD6 PD25 PD5 BD50 BD40 BD40 3/16 1/8 3/32 1/16 3/16 3/32 3/32 #40389 #40388 #40387 #40385 $6.95 $6.95 $ $9.00 $5.00 $ G 200G 400G Diamonds - 3/32 shafts D15 D16 D17 D18 D19 D20 #40300 #40301 #40302 #40303 #40304 #40305 D15 - D20... $13.50 each D21 D22 D23 D24 D25 D26 D27 #40308 #40309 #40310 #40311 #40312 #40313 #40314 D21-D27...$15.90 each D29 D30 #40315 #40316 $21.70 each D503 D504 D505 D506 #40320 #40321 #40322 #40323 $20.95 each D601 D602 D603 D604 D605 #40330 #40331 #40332 #40333 #40334 $19.25 each #40340 $ #40341 #40342 #40343 #40344 $11.20 $23.40 $7.05 $ #40345 #40346 #40347 #40348 $12.10 $21.45 $7.05 $ #40350 #40351 #40352 #40353 $21.45 $16.05 $7.05 $ #40355 #40356 #40357 #40358 $18.70 $8.15 $16.30 $ #40360 #40361 #40363 $12.10 $18.70 $ #40365 #40367 #40368 $12.10 $22.65 $10.00

7 22 DIAMONDS, SABURR-TOOTH AND KUTZALLS Diamonds - 3/32 shafts (continued) PD5 PD30 PD25 PD6 #40370 #40371 #40372 #40373 #40375 #40376 #40377 #40378 #40385 #40386 #40387 #40388 $11.20 $17.40 $18.25 $26.30 $18.00 $23.45 $22.65 $26.40 $5.00 $5.00 $5.00 $9.00 Saburr-Tooth Yellow fine 1/4 x 3/4 x 1-1/4 # $21.50 Kutzalls (silver) Left to right: Green coarse 3/4 x 1-1/4 # $21.50 Green coarse 1/2 x 3/4 # $16.50 Yellow fine 1/2 x 3/4 # $20.00 Yellow fine 3/32 x 1/4 x 1/2 # $15.00 Green coarse 1/8 x 1/4 x 1/2 # $ /4 x 1/2 x 1-3/4 cylinder # $ /2 x 3/4 flame # $ /4 x 1 disc 1/4 x 3/4 disc 1/8 x 1/2 disc # $16.00 each 1/8 x 5/16 x 1/2 1/8 x 3/8 1/8 x 1/4 cylinder ball ball # # $14.25 # $13.25 Left to right: 1/4 z 1/2 ballnose... # $ /4 x 3/8 flame...# $ /8 x 3/4 ballnose... # $ /8 x 3/4 taper... # $ /4 x 1/2 x 3/4 flame...# $16.00 Gold Kutzalls (Fine) Left to Right: 1/8 x 1 taper #T18-EG... $ /8 x 3/8 ball # $ /4 x 1/2 ball #S12G... $ /4 x 1 ball #S-1-G... $ /4 x 3/4 x 1-1/4 flame # $ /4 x 1/2 x 3/4 ball nose # $15.50