Pacal Blade Product Specifications

Transcription

1 Pacal Blade Product Specifications Table of Contents General Information How To Use This Product Specification Catalog... 3 Welding Instructions... 4 Alloys... 5 Terminology... 5 Product Identification... 6 Blades, End Bits & Cutting Edges Quote Template... 8 Pacal Blades Rolled Steel Blade Products Bolt-On Cutting Edges for Loader Buckets Weld-On DoubleDuty Vee Edges DoubleDuty Vee w/bolt-on Edges Modified Vee Edges Lip Assemblies Infinity 2000/ Infinity Cutting Edges, Corners and Gussets for Loader and Backhoe Buckets ForgeTemp Carbon Steel Cutting Edges MaxTemp Heat Treated Cutting Edges Corner Reinforcing Boots or Straight Corners for 3-Piece Wrap-Around Corner Reinforcing Boots or Extended Corners for 3-Piece Wrap-Around Corner Reinforcing Boots Flush Type and Inside Corner Gussets Special Application MaxTemp Cutting Edges for Excavators Grader Cutting Edges Grader MaxTemp Cutting Edges Cleaner Bars for Compactors... 66, Nuts and Washers Bobcat Skid Steer Case Dozer Loader Skid Steer Caterpillar Dozer Grader Loader Scraper Skid Steer Champion Grader Daewoo Loader Pacal Blades Specifications 1 May 1, 2011

2 Deere Dozer Grader Loader Scraper Skid Steer Dresser Dozer Grader Loader Scraper Fiatallis Dozer Grader Loader Scraper HYUNDAI Dozer Loader JCB Kawasaki Loader Kobelco Loader Komatsu Dozer Grader Loader Skid Steer New Holland Dozer Loader Skid Steer Terex Dozer Loader Scraper Tojan (O & K) Grader Loader Volvo Dozer Loader Grader Scraper Wabco Grader Scraper Pacal Blades Specifications 2 May 1, 2011

3 How to use the Product Specifications The specifications catalog has been organized to facilitate the search for ground engaging tools for all makes and models of equipment. OEMs are listed in alphabetical order followed by machine type which are sorted in the following sequence: dozer, loader, scraper, and grader. Under each machine type the various models are listed in the left hand column and organized in an alphanumeric format. Within each model section, edge groups are formed, and sorted according to length of moldboard. Edge groups represent one complete set of cutting edges for a particular moldboard. Variations of each group (i.e. HD, XHD), are also listed within that section along with optional equipment located at the bottom of each group. All wear parts found within a section are applicable to the same moldboard. Hole patterns are consistent throughout each edge group, but may or may not be interchangeable depending on thickness, width and / or application. A solid line separates the various models, and also serves as an indicator that the moldboard group has changed. Thickness and weights shown in the Product Specifications apply to MaxTemp products unless otherwise stated. For comparable ForgeTemp products refer to the Pacal Blades Price List. Additional product information is provided such as dimensions, quantities required per set, etc. with each column clearly marked at the top with a descriptive header. Pacal Blades Specifications 3 May 1, 2011

4 Welding Instructions Pacal Blades weld on base edges are produced from the highest quality steels and are designed to provide impact and abrasion resistance while maintaining their weldability. Following the welding instructions outlined within this catalog, will ensure the maximum performance of your Pacal Blades products. General: The following procedures should be followed when welding any Pacal Blades product. Use short stringer beads and remove slag after each pass Bevel joints to get 100% weld penetration, when possible All welding should be done in the flat horizontal position Peen each bead to reduce stress concentrations Hold interpass temperatures to under 500! WARNING: When performing the work described in these instructions, always work safely and use proper safety equipment to help avoid injury. Always wear hard hat, gloves, safety shoes, eye protection, hearing protection and fall protection per regional, national and site requirements (e.g. OSHA, MSHA) when performing maintenance work. To avoid injury to others, keep bystanders well out of the way. Loader base edges 1. Remove existing edge and prepare the surface to accept the replacement by cleaning up all rough edges and slag with a grinder. Mating surfaces should be shiny base metal, free of carbon arc surface, hardfacing, grease, paint, or dirt. 2. Position replacement edge in the bucket and securely clamp it to stiffener bars. 3. Preheat: Regardless of the welding process used, the entire weld area should be preheated to 350 to 400. This temperature should be maintained throughout the welding process. Interpass temperature should not exceed 500. To insure proper preheat, use of a Tempil stick, or Pyrometer is recommended. 4. Using conventional welding machines and rods ( electrodes ) the following is recommended: 5. Use AWS-E7018 Low Hydrogen (Min. 5/32 dia.) rod. It is important that the rod be absolutely dry. In bevel welds apply a minimum 3/16 throat section. ( See Ill. 1 ) 6. Welding Sequence - Start at the center of the cutting edge and begin welding 3 strips leaving 12 gaps between welds ( See Ill. 2) Alternate passes from center to left and right, working towards the ends of the bucket. 7. Continue alternating weld sequence until all spaces are filled. Apply a min. 3/16 fillet weld. Finish welding cutting edge to bucket ends, inside and outside to complete installation. 8. Postheat - Having maintained 350 to 400 throughout the welding process, it is important to avoid rapid cooling. Allow the weld area to cool slowly before use. 9. Semi-Automatic Weld Process 10. Submerged Arc Welding ( SAW ) 11. Flux Cored Arc Welding ( FCAW ) 12. Gas Metalic Arc Welding ( GMAW ) Any of the above welding processes may be utilized providing they produce a low hydrogen type weld deposit comparable to AWS-E7018 welding rod. Due to variables, it will be necessary to consult a local welding materials supplier for specific details to amperage, voltage, type of wire, gas shielding, and travel speed. Pacal Blades Specifications 4 May 1, 2011

5 Alloys Field experience has proven that specific end-use applications require job engineered products. Therefore, Pacal Blades begins with an engineering analysis to make certain the steel formula for each specific application has the proper combination of qualities. Each steel provides balanced metallurgical characteristics to best resist wear and breakage. Pacal Blades works with end users to provide the best product for each application. ForgeTemp : ForgeTemp steel is designed for high abrasion, low impact conditions. This high carbon steel alloy provides a balance between wear resistance and impact breakage. The steel is specially prepared in the mill to create the highest forging quality steel. ForgeTemp products are available in OEM standard, heavy duty, extra heavy duty and Magnum designs. MaxTemp : MaxTemp steel is a heat-treated, through-hardened steel that delivers maximum protection against breakage in the toughest high-impact applications. Designed for the most demanding jobs, all MaxTemp products are guaranteed against impact breakage. MaxTemp products are available in OEM standard, heavy duty, and extra heavy duty designs. Special Application MaxTemp : Special Application MaxTemp is a heat-treated alloy developed specifically for heavy-duty loaders and excavator applications. Impact resistant, wear resistant, and easy to weld, Special Application MaxTemp is uniquely suited to handle the punishment large production machines dish out. Special Application MaxTemp steel is available for weld-in straight, spade, and modified vee moldboards. Carbide Plus : Pacal Blades Carbide Plus embedded wear products, offer a significant increase in wear life over conventional steel products. Designed for low impact, high abrasive conditions, Carbide Plus products are guaranteed to offer cost effective service in factory recommended applications. Terminology The following is a listing of abbreviations and terms which are found throughout the Product Specifications. Learning of the terminology will speed up the identification process, and help make better product selections. * and ** Refers to notes at end of section Ang Angled Assy Assembly B/O Bolt-On c/e Cutting Edge CDB Curved Double Bevel CNB Curved No Bevel Cor Corner CS Cap screw CSB Curved Single Bevel Ctr Center DD DoubleDuty Section Ext Ser Extreme Service Extd Extended FAB Fabrication FDB Flat Double Bevel FDD Flat DoubleDuty FGE Forge FSB Flat Single Bevel FSE Flat Square Edge Pacal Blades Specifications 5 May 1, 2011

6 FT ForgeTemp HC Hot Cupped (formed) HD Heavy Duty HD-MAG Heavy Duty Magnum HDMT Heavy Duty MaxTemp ID Inside Dimension Int Ends Intermediate Ends on "U" type dozers L Left (only) LH Left Hand MAG Magnum MT MaxTemp OAL Overall Length Pc Piece R Right (only) R/L Right or Left (interchangeable) Reinf Reinforcing Reqd Required Rev Bev Reverse Bevel RF Roll Forged RH Right Hand Seg Segments SHS State Highway Standard Spl Special St Straight Std Standard W/O Weld-On WBO With Bolt-On XHD Extra Heavy Duty XXHD Extra Extra Heavy Duty Product Identification The Pacal Blades Product Specifications uses OEM part numbers for item identification to help insure the accuracy of orders. Although this is the preferred method of identifying parts, measurements can also be used in conjunction with machine information to help identification. Hole spacing and additional product specifications not listed in the catalog can be provided by a customer service representative. Obtaining the following information can drastically reduce the amount of time needed to identify products, and eliminate costly returns due to improper identification. To assist in this process templates are provided at the end of this section. Dozer - A. Make of machine B. Model of machine C. Blade type D. Total number of pieces that comprise the edge set E. The length of each edge as shown below in Ill. 1 F. Total number of holes in each edge G. Spacing between holes from center to center H. Bolt size I. Total number of holes in each end bit Pacal Blades Specifications 6 May 1, 2011

7 Loader - Weld On Base A. Make of machine B. Model of machine C. Bucket width. See Ill. 2 D. Total number of holes in edge E. Spacing between holes from center to center F. Hole size Note: If edge has more than one row of holes, then the following information is also needed. G. Distance from leading edge to center of first row of holes H. Distance from center of first row to the center of the second row of holes Loader - Bolt On Edge Group A. Make of machine B. Model of machine C. Bucket width. See Ill. 2 D. Total number of pieces that comprise the edge set E. The length of each edge See Ill. 1 F. Total number of holes in each edge G. Spacing between holes from center to center H. Bolt size Scraper - A. Make of machine B. Model of machine C. Total number of pieces that comprise the edge set D. The length of each edge as shown below in Ill. 1 E. Total number of holes in each edge F. Spacing between holes from center to center G. Bolt size Ill. 2 Ill. 1 NOTE: Bucket width is measured from outside edge to outside edge. Do not include material welded up the side in the measurement Pacal Blades Specifications 7 May 1, 2011

8 TEMPLATES Blades, End Bits & Cutting Edges Quote Template The following templates may be used as forms to request quotations for Pacal Blades rolled steel Blades, End Bits and Cutting Edges. Select the form that best fits the item to be quoted and fill out the requested information. Submit the form to your Pacal Blades representative for a quotation. Pacal Blades Specifications 8 May 1, 2011

9 TEMPLATES Pacal Blades Specifications 9 May 1, 2011

10 TEMPLATES Pacal Blades Specifications 10 May 1, 2011

11 TEMPLATES Pacal Blades Specifications 11 May 1, 2011

12 TEMPLATES Pacal Blades Specifications 12 May 1, 2011

13 TEMPLATES Pacal Blades Specifications 13 May 1, 2011

14 TEMPLATES Pacal Blades Specifications 14 May 1, 2011

15 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Red indicated changed made since last published ESCO bolt-on blade systems for loader buckets are designed to provide quick replacement of cutting edges, while increasing the overall integrity of the bucket. Each edge group offers both double bevel and DoubleDuty bolt-ons. Double Bevel edges are designed for operation in low impact conditions, DoubleDuty offers added shear strength and base edge protection needed for more severe applications. All ESCO bolt-on blade systems are produced from the highest quality steels and manufactured to exacting standards to meet the most demanding jobs. To determine the correct cutting edge group, identify: 1) Machine class - Machine class is determined by weight or size. Listed in the left hand column are various models and weights of popular machines. If a specific machine is not listed, identify the class by using the approximate weight of the unit. 2) Bucket width - Bucket width is determined by measuring the bucket outside wall to outside wall. Base edges listed in this section are designed to allow the appropriate amount of overhang to accommodate weld-on corners listed in each section. Note: For recommended welding procedures or details on how to take bucket measurements, refer to the General Information section of the Product Specifications. Pacal Blades Specifications 15 May 1, 2011

16 Pacal Blades Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets With Overall Widths Of 48-1/8" thru 50" Weight Class of Less Bolt-On Cutting Edges for Loader Buckets than 15,000 lb. Weld-On Base w/ends BB1-LR /4 x 6 x 51-3/4 FSB 10 Weld-On /4 x 6 Base Bolt-On Edge RH(MT Only) BB2-LR /8 x 8 x 26-1/16 FDD 5 3/4 x Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 26-1/16 FDD 5 3/4 x Case: 1835B, 1845C Bolt-On Edge R/L BB1-LR x 8 x 26-1/16 FDB 5 3/4 x Super E, 680K 780C, W11B For Buckets With Overall Widths of 50-1/8" thru 52" Caterpillar: 416, 426 Weld-On Base w/ends BB1-LR /4 x 6 x 53-3/4 FSB 10 Weld-On - 78 Deere: Bolt-On Edge RH(MT Only) BB2-LR /8 x 8 x 27-1/16 FDD 5 3/4 x , 675, 310C Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 27-1/16 FDD 5 3/4 x C, 510C,610C 710B Bolt-On Edge R/L BB1-LR x 8 x 27-1/16 FDB 5 3/4 x For Buckets With Overall Widths of 52-1/8" thru 54" Weld-On Base w/ends BB1-LR /4 x 6 x 55-3/4 FSB 11 Weld-On - 80 Bolt-On Edge RH(MT Only) BB2-LR /8 x 8 x 26-1/16 FDD 5 3/4 x Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 30-1/16 FDD 6 3/4 x Bolt-On Edge RH BB1-LR x 8 x 26-1/16 FDB 5 3/4 x Bolt-On Edge LH BB1-LR x 8 x 30-1/16 FDB 6 3/4 x For Buckets With Overall Widths of 54-1/8" thru 56" Weld-On Base w/ends BB1-LR /4 x 6 x 57-3/4 FSB 11 Weld-On - 83 Bolt-On Edge RHMT Only) BB2-LR /8 x 8 x 27-1/16 FDD 5 3/4 x Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 31-1/16 FDD 6 3/4 x Bolt-On Edge RH BB1-LR x 8 x 27-1/16 FDB 5 3/4 x Bolt-On Edge LH BB1-LR x 8 x 31-1/16 FDB 6 3/4 x For Buckets With Overall Widths Of 56-1/8" to 58" Weld-On Base w/ends BB1-LR /4 x 6 x 59-3/4 FSB 12 Weld-On - 85 Bolt-On Edge RH(MT Only) BB2-LR /8 x 8 x 30-1/16 FDD 6 3/4 x Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 30-1/16 FDD 6 3/4 x Bolt-On Edge R/L BB1-LR x 8 x 30-1/16 FDB 6 3/4 x For Buckets With Overall Widths Of 58-1/8" to 60" Weld-On Base w/ends BB1-LR /4 x 6 x 61-3/4 FSB 12 Weld-On 88 Bolt-On Edge RH(MT Only) BB2-LR /8 x 8 x 31-1/16 FDD 6 7/8 x Bolt-On Edge LH(MT Only) BB2-LR /8 x 8 x 31-1/16 FDD 6 7/8 x Bolt-On Edge R/L BB2-LR x 8 x 31-1/16 FDB 6 7/8 x (continued) Pacal Blades Specifications 16 May 1, 2011

17 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 60-1/8" thru 62" Loaders in the Weld-On Base w/ends BB2-LR /4 x 6 x 63-3/4 FSB 12 Weld-On - 90 Weight Class of Less than 15,000 lb. Bolt-On Center(MT Only) BB2-LR /8 x 8 x 18-7/8 FDD 4 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ /4 x 6 Base Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Case: Bolt-On Center BB1-LR x 8 x 18-7/8 FDB 4 7/8 x 2-1/ B, 1845C Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ Super E, 680K 780C, W11B For Buckets With Overall Widths Of 62-1/8" thru 64 " Caterpillar: 416, 426 Weld-On Base w/ends BB1-LR /4 x 6 x 65-3/4 FSB 13 Weld-On - 92 Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 22-7/8 FDD 5 7/8 x 2-1/ , 675, 310C Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ C, 510C,610C Bolt 0n End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ B Bolt-On Center BB1-LR x 8 x 22-7/8 FDB 5 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 64-1/8" thru 66" Weld-On Base w/ends BB1-LR /4 x 6 x 67-3/4 FSB 13 Weld-On - 94 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 24-7/8 FDD 5 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 24-7/8 FDB 5 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 66-1/8" thru 68" Weld-On Base w/ends BB1-LR /4 x 6 x 69-3/4 FSB 13 Weld-On - 97 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 24-7/8 FDD 5 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 24-7/8 FDB 5 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 68-1/8" thru 70" Weld-On Base w/ends BB1-LR /4 x 6 x 71-3/4 FSB 14 Weld-On - 99 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 28-7/8 FDD 6 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 28-7/8 FDB 6 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 17 May 1, 2011

18 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 70-1/8" thru 72" Loaders in the Weight Class of Less Weld-On Base w/ends BB1-LR /4 x 6 x 73-3/4 FSB 14 Weld-On than 15,000 lb. 3/4 x 6 Base Bolt-On Center(MT Only) BB2-LR /8 x 8 x 28-7/8 FDD 6 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Case: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ B, 1845C 580 Super E, 680K Bolt-On Center BB2-LR x 8 x 28-7/8 FDB 6 7/8 x 2-3/ C, W11B Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-3/ Caterpillar: 416, 426 For Buckets With Overall Widths Of 72-1/8" thru 74" Deere: Weld-On Base w/ends BB1-LR /4 x 6 x 75-3/4 FSB 15 Weld-On , 675, 310C 410C, 510C,610C Bolt-On Center(MT Only) BB2-LR /8 x 8 x 32-7/8 FDD 7 7/8 x 2-1/ B Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 32-7/8 FDB 7 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 74-1/8" thru 76" Weld-On Base w/ends BB1-LR /4 x 6 x 77-3/4 FSB 15 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 32-7/8 FDD 7 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 32-7/8 FDB 7 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 76-1/8" thru 78" Weld-On Base w/ends BB1-LR /4 x 6 x 79-3/4 FSB 16 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 36-7/8 FDD 8 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 36-7/8 FDB 8 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 78-1/8" thru 80" Weld-On Base w/ends BB2-LR /4 x 6 x 81-3/4 FSB 16 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 36-7/8 FDD 8 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 36-7/8 FDB 8 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 18 May 1, 2011

19 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) Loaders in the For Buckets With Overall Widths Of 80-1/8" thru 82" Weight Class of Less than 15,000 lb. Weld-On Base w/ends BB2-LR /4 x 6 x 83-3/4 FSB 17 Weld-On /4 x 6 Base Bolt-On Center(MT Only) BB2-LR /8 x 8 x 40-7/8 FDD 9 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Case: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ B, 1845C 580 Super E, 680K Bolt-On Center BB2-LR x 8 x 40-7/8 FDB 9 7/8 x 2-1/ C, W11B Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ Caterpillar: 416, 426 For Buckets With Overall Widths Of 82-1/8 " thru 84" Deere: Weld-On Base w/ends BB1-LR /4 x 6 x 85-3/4 FSB 17 Weld-On , 675, 310C 410C, 510C,610C Bolt-On Center(MT Only) BB2-LR /8 x 8 x 40-7/8 FDD 9 7/8 x 2-1/ B Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 40-7/8 FDB 9 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Of Widths 84-1/8" thru 86" Weld-On Base w/ends BB1-LR /4 x 6 x 87-3/4 FSB 18 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 44-7/8 FDD 10 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 44-7/8 FDB 10 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths of 86-1/8" thru 88" Weld-On Base w/ends BB1-LR /4 x 6 x 89-3/4 FSB 18 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 44-7/8 FDD 10 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB2-LR x 8 x 44-7/8 FDB 10 7/8 x 2-1/ Bolt-On End R/L BB1-LR x 8 x 22-9/16 FDB 4 7/8 x 2-1/ Pacal Blades Specifications 19 May 1, 2011

20 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets With Overall Widths of 60-1/8" thru 62" Weight Class of 15,000 lb to 26,000 lb Weld-On Base w/ends BB1-LR x 8 x 63-3/4 FSB 12 Weld-On " x 8" Base Bolt-On Center(MT Only) BB2-LR /8 x 8 x 18-7/8 FDD 4 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Case: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ W14B, W20C W24C Bolt-On Center BB1-LR /4 x 10 x 18-7/8 FDB 4 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ Caterpillar: 910, IT12, 916 IT18, 926, IT28 For Buckets With Overall Widths Of 62-1/8" thru 64" 930 Weld-On Base w/ends BB1-LR x 8 x 65-3/4 FSB 13 Weld-On Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 22-7/8 FDD 5 7/8 x 2-1/ D, 544D Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Dresser: H50C, H60E, H65E Bolt-On Center BB1-LR /4 x 10 x 22-7/8 FDB 5 7/8 x 2-1/ B, 515B, 520B Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ Fiatallis: FR7, 345B For Buckets With Overall Widths Of 64-1/8" thru 66" FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 67-3/4 FSB 13 Weld-On Komatsu: WA100-1, WA120-1 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 24-7/8 FDD 5 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Terex: Bolt-On Center BB1-LR /4 x 10 x 24-7/8 FDB 5 7/8 x 2-1/ , 33C, 44C Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ VME: L50, 35C, 45C For Buckets With Overall Widths Of 66-1/8" thru 68" L70, 55C Weld-On Base w/ends BB1-LR x 8 x 69-3/4 FSB 13 Weld-On Kawasaki: KSS65Z Bolt-On Center(MT Only) BB2-LR /8 x 8 x 24-7/8 FDD 5 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Trojan: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 24-7/8 FDB 5 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 68-1/8" thru 70" Weld-On Base w/ends BB1-LR x 8 x 71-3/4 FSB 14 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 28-7/8 FDD 6 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 28-7/8 FDB 6 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 20 May 1, 2011

21 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 70-1/8" thru 72" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 8 x 73-3/4 FSB 14 Weld-On ,000 lb to 26,000 lb Bolt-On Center(MT Only) BB2-LR /8 x 8 x 28-7/8 FDD 6 7/8 x 2-1/ " x 8" Base Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Case: W14B, W20C Bolt-On Center BB1-LR /4 x 10 x 28-7/8 FDB 6 7/8 x 2-1/ W24C Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ Caterpillar: 910, IT12, 916 For Buckets With Overall Widths Of 72-1/8" thru 74" IT18, 926, IT28 Weld-On Base w/ends BB1-LR x 8 x 75-3/4 FSB 15 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 32-7/8 FDD 7 7/8 x 2-1/ Deere: Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ D, 544D Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Dresser: Bolt-On Center BB1-LR /4 x 10 x 32-7/8 FDB 7 7/8 x 2-1/ H50C, H60E, H65E Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ B, 515B, 520B Fiatallis: For Buckets With Overall Widths Of 74-1/8" thru 76" FR7, 345B FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 77-3/4 FSB 15 Weld-On Komatsu: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 32-7/8 FDD 7 7/8 x 2-1/ WA100-1, WA120-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On Center BB1-LR /4 x 10 x 32-7/8 FDB 7 7/8 x 2-1/ Terex: Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ , 33C, 44C VME: For Buckets With Overall Widths Of 76-1/8" thru 78" L50, 35C, 45C L70, 55C Weld-On Base w/ends BB1-LR x 8 x 79-3/4 FSB 16 Weld-On Kawasaki: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 36-7/8 FDD 8 7/8 x 2-1/ KSS65Z Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Trojan: 1500Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 36-7/8 FDB 8 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 78-1/8" thru 80" Weld-On Base w/ends BB1-LR x 8 x 81-3/4 FSB 16 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 36-7/8 FDD 8 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 36-7/8 FDB 8 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 21 May 1, 2011

22 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 80-1/8" thru 82" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 8 x 83-3/4 FSB 17 Weld-On ,000 lb to 26,000 lb Bolt-On Center(MT Only) BB2-LR /8 x 8 x 40-7/8 FDD 9 7/8 x 2-1/ " x 8" Base Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Case: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ W14B, W20C Bolt-On Center BB1-LR /4 x 10 x 40-7/8 FDB 9 7/8 x 2-1/ W24C Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ Caterpillar: 910, IT12, 916 IT18, 926, IT28 For Buckets With Overall Widths Of 82-1/8" thru 84" 930 Weld-On Base w/ends BB1-LR x 8 x 85-3/4 FSB 17 Weld-On Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 40-7/8 FDD 9 7/8 x 2-1/ D, 544D Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Dresser: H50C, H60E, H65E Bolt-On Center BB1-LR /4 x 10 x 40-7/8 FDB 9 7/8 x 2-1/ B, 515B, 520B Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ Fiatallis: FR7, 345B For Buckets With Overall Widths Of 84-1/8" thru 86" FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 87-3/4 FSB 18 Weld-On Komatsu: WA100-1, WA120-1 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 44-7/8 FDD 10 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Terex: Bolt-On Center BB1-LR /4 x 10 x 44-7/8 FDB 10 7/8 x 2-1/ , 33C, 44C Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ VME: L50, 35C, 45C For Buckets With Overall Widths Of 86-1/8" thru 88" L70, 55C Weld-On Base w/ends BB1-LR x 8 x 89-3/4 FSB 18 Weld-On Kawasaki: KSS65Z Bolt-On Center(MT Only) BB2-LR /8 x 8 x 44-7/8 FDD 10 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Trojan: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 44-7/8 FDB 10 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 88-1/8" thru 90" Weld-On Base w/ends BB1-LR x 8 x 91-3/4 FSB 19 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 48-7/8 FDD 11 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 48-7/8 FDB 11 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 22 May 1, 2011

23 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 90-1/8" thru 92" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 8 x 93-3/4 FSB 19 Weld-On ,000 lb to 26,000 lb Bolt-On Center(MT Only) BB2-LR /8 x 8 x 48-7/8 FDD 11 7/8 x 2-1/ " x 8" Base Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Case: W14B, W20C Bolt-On Center BB1-LR /4 x 10 x 48-7/8 FDB 11 7/8 x 2-1/ W24C Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ Caterpillar: 910, IT12, 916 IT18, 926, IT28 For Buckets With Overall Widths Of 92-1/8" thru 94" 930 Weld-On Base w/ends BB1-LR x 8 x 95-3/4 FSB 20 Weld-On Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 52-7/8 FDD 12 7/8 x 2-1/ D, 544D Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Dresser: H50C, H60E, H65E Bolt-On Center BB1-LR /4 x 10 x 52-7/8 FDB 12 7/8 x 2-1/ B, 515B, 520B Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ Fiatallis: FR7, 345B For Buckets With Overall Widths Of 94-1/8" thru 96" FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 97-3/4 FSB 20 Weld-On Komatsu: WA100-1, WA120-1 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 52-7/8 FDD 12 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Terex: Bolt-On Center BB1-LR /4 x 10 x 52-7/8 FDB 12 7/8 x 2-1/ , 33C, 44C Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ VME: L50, 35C, 45C For Buckets With Overall Widths Of 96-1/8" thru 98" L70, 55C Weld-On Base w/ends BB1-LR x 8 x 99-3/4 FSB 21 Weld-On Kawasaki: KSS65Z Bolt-On Center(MT Only) BB2-LR /8 x 8 x 56-7/8 FDD 13 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Trojan: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 21-9/16 FDD 4 7/8 x 2-1/ Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 56-7/8 FDB 13 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 21-9/16 FDB 4 7/8 x 2-1/ For Buckets With Overall Widths Of 98-1/8" thru 100" Weld-On Base w/ends BB1-LR x 8 x 101-3/4 FSB 21 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 56-7/8 FDD 13 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 22-9/16 FDD 4 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 56-7/8 FDB 13 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 22-9/16 FDB 4 7/8 x 2-1/ (continued) Pacal Blades Specifications 23 May 1, 2011

24 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 100-1/8" thru 102" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 8 x 103-3/4 FSB 22 Weld-On ,000 lb to 26,000 lb Bolt-On Center(MT Only) BB2-LR /8 x 8 x 50-7/8 FDD 12 7/8 x 2-1/ " x 8" Base Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Case: W14B, W20C Bolt-On Center BB1-LR /4 x 10 x 50-7/8 FDB 12 7/8 x 2-1/ W24C Bolt-On End R/L BB1-LR /4 x 10 x 26-9/16 FDB 5 7/8 x 2-1/ Caterpillar: 910, IT12, 916 IT18, 926, IT28 For Buckets With Overall Widths Of 102-1/8" thru 104" 930 Weld-On Base w/ends BB1-LR x 8 x 105-3/4 FSB 22 Weld-On Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 50-7/8 FDD 12 7/8 x 2-1/ D, 544D Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Dresser: H50C, H60E, H65E Bolt-On Center BB1-LR /4 x 10 x 50-7/8 FDB 12 7/8 x 2-1/ B, 515B, 520B Bolt-On End R/L BB1-LR /4 x 10 x 27-9/16 FDB 5 7/8 x 2-1/ Fiatallis: FR7, 345B For Buckets With Overall Widths Of 104-1/8" thru 106" FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 107-3/4 FSB 23 Weld-On Komatsu: WA100-1, WA120-1 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 54-7/8 FDD 13 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Terex: Bolt-On Center BB1-LR /4 x 10 x 54-7/8 FDB 13 7/8 x 2-1/ , 33C, 44C Bolt-On End R/L BB1-LR /4 x 10 x 26-9/16 FDB 5 7/8 x 2-1/ VME: L50, 35C, 45C For Buckets With Overall Widths Of 106-1/8" thru 108" L70, 55C Weld-On Base w/ends BB1-LR x 8 x 109-3/4 FSB 23 Weld-On Kawasaki: KSS65Z Bolt-On Center(MT Only) BB2-LR /8 x 8 x 54-7/8 FDD 13 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Trojan: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 54-7/8 FDB 13 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 27-9/16 FDB 5 7/8 x 2-1/ For Buckets With Overall Widths Of 108-1/8" thru 110" Weld-On Base w/ends BB1-LR x 8 x 111-3/4 FSB 24 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 58-7/8 FDD 14 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 58-7/8 FDB 14 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 26-9/16 FDB 5 7/8 x 2-1/ (continued) Pacal Blades Specifications 24 May 1, 2011

25 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 110-1/8" thru 112" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 8 x 113-3/4 FSB 24 Weld-On ,000 lb to 26,000 lb Bolt-On Center(MT Only) BB2-LR /8 x 8 x 58-7/8 FDD 14 7/8 x 2-1/ " x 8" Base Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Case: W14B, W20C Bolt-On Center BB1-LR /4 x 10 x 58-7/8 FDB 14 7/8 x 2-1/ W24C Bolt-On End R/L BB1-LR /4 x 10 x 27-9/16 FDB 5 7/8 x 2-1/ Caterpillar: 910, IT12, 916 IT18, 926, IT28 For Buckets With Overall Widths Of 112-1/8" thru 114" 930 Weld-On Base w/ends BB1-LR x 8 x 115-3/4 FSB 25 Weld-On Deere: Bolt-On Center(MT Only) BB2-LR /8 x 8 x 62-7/8 FDD 15 7/8 x 2-1/ D, 544D Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Dresser: H50C, H60E, H65E Bolt-On Center BB1-LR /4 x 10 x 62-7/8 FDB 15 7/8 x 2-1/ B, 515B, 520B Bolt-On End R/L BB1-LR /4 x 10 x 26-9/16 FDB 5 7/8 x 2-1/ Fiatallis: FR7, 345B For Buckets With Overall Widths Of 114-1/8" thru 116" FR10B, FR11 Weld-On Base w/ends BB1-LR x 8 x 117-3/4 FSB 25 Weld-On Komatsu: WA100-1, WA120-1 Bolt-On Center(MT Only) BB2-LR /8 x 8 x 62-7/8 FDD 15 7/8 x 2-1/ WA150-1, WA180-1 Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ WA200-1, WA250-1 Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Terex: Bolt-On Center BB1-LR /4 x 10 x 62-7/8 FDB 15 7/8 x 2-1/ , 33C, 44C Bolt-On End R/L BB1-LR /4 x 10 x 27-9/16 FDB 5 7/8 x 2-1/ VME: L50, 35C, 45C For Buckets With Overall Widths Of 116-1/8" thru 118" L70, 55C Weld-On Base w/ends BB1-LR x 8 x 119-3/4 FSB 26 Weld-On Kawasaki: KSS65Z Bolt-On Center(MT Only) BB2-LR /8 x 8 x 66-7/8 FDD 16 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Trojan: Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 26-9/16 FDD 5 7/8 x 2-1/ Z, 1900Z Bolt-On Center BB1-LR /4 x 10 x 66-7/8 FDB 16 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 26-9/16 FDB 5 7/8 x 2-1/ For Buckets With Overall Widths Of 118-1/8" thru 120" Weld-On Base w/ends BB1-LR x 8 x 121-3/4 FSB 26 Weld-On Bolt-On Center(MT Only) BB2-LR /8 x 8 x 66-7/8 FDD 16 7/8 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /8 x 8 x 27-9/16 FDD 5 7/8 x 2-1/ Bolt-On Center BB1-LR /4 x 10 x 66-7/8 FDB 219 7/8 x 2-1/ Bolt-On End R/L BB1-LR /4 x 10 x 27-9/16 FDB 5 7/8 x 2-1/ Pacal Blades Specifications 25 May 1, 2011

26 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets With Overall Widths Of 82-1/8" thru 84" Weight Class of 26,000 lb to 40,000 lb Weld-On Base w/ends BB1-LR /4 x 9 x 86-1/4 FSB 17 Weld-On /4" x 9" Base Bolt-On Center(MT Only) BB2-LR /4 x 10 x 32-7/8 FDD 7 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Case: Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ W24C, W26B W30, W36 Bolt-On Center BB1-LR /2 x 12 x 32-7/8 FDB 7 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 84-1/8" thru 86" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 88-1/4 FSB 17 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 32-7/8 FDD 7 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 32-7/8 FDB 7 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 86-1/8" thru 88" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 90-1/4 FSB 18 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 36-7/8 FDD 8 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 36-7/8 FDB 8 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ Kawasaki: KSS70Z For Buckets With Overall Widths Of 88-1/8" thru 90" Trojan: 2000Z, 3500Z Weld-On Base w/ends BB1-LR /4 x 9 x 92-1/4 FSB 18 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 36-7/8 FDD 8 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 36-7/8 FDB 8 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ For Buckets With Overall Widths Of 90-1/8" thru 92" Weld-On Base w/ends BB1-LR /4 x 9 x 94-1/4 FSB 19 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 40-7/8 FDD 9 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 40-7/8 FDB 9 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ (continued) Pacal Blades Specifications 26 May 1, 2011

27 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 92-1/8" thru 94" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /4 x 9 x 96-1/4 FSB 19 Weld-On ,000 lb to 40,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 40-7/8 FDD 9 1 x 2-1/ /4" x 9" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Case: W24C, W26B Bolt-On Center BB1-LR /2 x 12 x 40-7/8 FDB 9 1 x 2-1/ W30, W36 Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 94-1/8" thru 96" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 98-1/4 FSB 20 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 44-7/8 FDD 10 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 44-7/8 FDB 10 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 96-1/8" thru 98" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 100-1/4 FSB 20 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 44-7/8 FDD 10 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 44-7/8 FDB 10 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ Kawasaki: KSS70Z For Buckets With Overall Widths Of 98-1/8" thru 100" Trojan: 2000Z, 3500Z Weld-On Base w/ends BB1-LR /4 x 9 x 102-1/4 FSB 21 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 48-7/8 FDD 11 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 48-7/8 FDB 11 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ For Buckets With Overall Widths Of 100-1/8" thru 102" Weld-On Base w/ends BB1-LR /4 x 9 x 104-1/4 FSB 21 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 48-7/8 FDD 11 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 48-7/8 FDB 11 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ (continued) Pacal Blades Specifications 27 May 1, 2011

28 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 102-1/8" thru 104" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /4 x 9 x 106-1/4 FSB 22 Weld-On ,000 lb to 40,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 12 1 x 2-1/ /4" x 9" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-1/ Case: W24C, W26B Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 12 1 x 2-1/ W30, W36 Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 104-1/8" thru 106" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 108-1/4 FSB 22 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 12 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 12 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 106-1/8" thru 108" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 110-1/4 FSB 23 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 46-7/8 FDD 11 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 46-7/8 FDB 11 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-1/ Kawasaki: KSS70Z For Buckets With Overall Widths Of 108-1/8" thru 110" Trojan: 2000Z, 3500Z Weld-On Base w/ends BB1-LR /4 x 9 x 112-1/4 FSB 23 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 46-7/8 FDD 11 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 46-7/8 FDB 11 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-1/ For Buckets With Overall Widths Of 110-1/8" thru 112" Weld-On Base w/ends BB1-LR /4 x 9 x 114-1/4 FSB 24 Weld-On Bolt-On Center(MT Only) BB1-LR /4 x 10 x 50-7/8 FDD 12 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 50-7/8 FDB 12 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-1/ (continued) Pacal Blades Specifications 28 May 1, 2011

29 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 112-1/8" thru 114" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /4 x 9 x 116-1/4 FSB 24 Weld-On ,000 lb to 40,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 50-7/8 FDD 12 1 x 2-1/ /4" x 9" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Case: W24C, W26B Bolt-On Center BB1-LR /2 x 12 x 50-7/8 FDB 12 1 x 2-1/ W30, W36 Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 114-1/8" thru 116" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 118-1/4 FSB 25 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 54-7/8 FDD 13 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 54-7/8 FDB 13 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 116-1/8" thru 118" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 120-1/4 FSB 25 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 54-7/8 FDD 13 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 54-7/8 FDB 13 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-1/ Kawasaki: KSS70Z For Buckets With Overall Widths Of 118-1/8" thru 120" Trojan: 2000Z, 3500Z Weld-On Base w/ends BB1-LR /4 x 9 x 122-1/4 FSB 26 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 58-7/8 FDD 14 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 58-7/8 FDB 14 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-1/ For Buckets With Overall Widths Of 120-1/8" thru 122" Weld-On Base w/ends BB1-LR /4 x 9 x 124-1/4 FSB 26 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 58-7/8 FDD 14 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 58-7/8 FDB 14 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-1/ (continued) Pacal Blades Specifications 29 May 1, 2011

30 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 122-1/8" thru 124" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /4 x 9 x 126-1/4 FSB 20 Weld-On ,000 lb to 40,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 13 1 x 2-1/ /4" x 9" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Case: W24C, W26B Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 13 1 x 2-1/ W30, W36 Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 124-1/8" thru 126" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 128-1/4 FSB 27 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 13 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 13 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 126-1/8" thru 128" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 130-1/4 FSB 28 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 56-7/8 FDD 14 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 56-7/8 FDB 14 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-1/ Kawasaki: KSS70Z For Buckets With Overall Widths Of 128-1/8" thru 130" Trojan: 2000Z, 3500Z Weld-On Base w/ends BB1-LR /4 x 9 x 132-1/4 FSB 28 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 56-7/8 FDD 14 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 56-7/8 FDB 14 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-1/ For Buckets With Overall Widths Of 130-1/8" thru 132" Weld-On Base w/ends BB1-LR /4 x 9 x 134-1/4 FSB 29 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 60-7/8 FDD 15 1 x 2-1/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Bolt-On Center BB1-LR /2 x 12 x 60-7/8 FDB 15 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-1/ (continued) Pacal Blades Specifications 30 May 1, 2011

31 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 132-1/8" thru 134" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /4 x 9 x 136-1/4 FSB 29 Weld-On ,000 lb to 40,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 60-7/8 FDD 15 1 x 2-1/ /4" x 9" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Case: W24C, W26B Bolt-On Center BB1-LR /2 x 12 x 60-7/8 FDB 15 1 x 2-1/ W30, W36 Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-1/ Caterpillar: 936, 950B, 966C For Buckets With Overall Widths Of 134-1/8" thru 136" Deere: 644D Weld-On Base w/ends BB1-LR /4 x 9 x 138-1/4 FSB 30 Weld-On Dresser: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 64-7/8 FDD 16 1 x 2-1/ H80B, H90E Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ B, 540A Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-1/ Fiatallis: Bolt-On Center BB1-LR /2 x 12 x 64-7/8 FDB 16 1 x 2-1/ FR12B, FT15B Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-1/ Komatsu: WA300-1, WA320-1 For Buckets With Overall Widths Of 136-1/8" thru 138" WA350-1, WA380-1 WA400-1 Weld-On Base w/ends BB1-LR /4 x 9 x 140-1/4 FSB 30 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 64-7/8 FDD 16 1 x 2-1/ C, 60C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-1/ VME: L90, 75C, L120 Bolt-On Center BB1-LR /2 x 12 x 64-7/8 FDB 16 1 x 2-1/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-1/ Kawasaki: KSS70Z Trojan: 2000Z, 3500Z Pacal Blades Specifications 31 May 1, 2011

32 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets With Overall Widths Of 94-1/8" thru 96" Weight Class of 40,000 lb to 80,000 lb Weld-On Base w/ends BB1-LR /2 x 12 x 98-1/4 FSB 20 Weld-On /2" x 12" Base Bolt-On Center(MT Only) BB2-LR /4 x 10 x 44-7/8 FDD 10 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ Caterpillar: Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ C, 988B Bolt-On Center BB1-LR /2 x 12 x 44-7/8 FDB 10 1 x 2-3/ Deere: Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-3/ Dresser: For Buckets With Overall Widths Of 96-1/8" thru 98" H100C, H120C 550, 560B Weld-On Base w/ends BB1-LR /2 x 12 x 100-1/4 FSB 20 Weld-On Fiatallis: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 44-7/8 FDD 10 1 x 2-3/ FR20B, FR30 Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ B, FR35 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ Komatsu: Bolt-On Center BB1-LR /2 x 12 x 44-7/8 FDB 10 1 x 2-3/ WA420-1, WA450-1 Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-3/ WA470-1, WA500-1 Terex: For Buckets With Overall Widths Of 98-1/8" thru 100" 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 102-1/4 FSB 21 Weld-On VME: 125C, 175C Bolt-On Center(MT Only) BB2-LR /4 x 10 x 48-7/8 FDD 11 1 x 2-3/ L160, 275C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ Kawasaki: KSS85Z11 Bolt-On Center BB1-LR /2 x 12 x 48-7/8 FDB 11 1 x 2-3/ KSS95Z Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-3/ Trojan: 4500Z, 5500Z For Buckets With Overall Widths Of 100-1/8" thru 102" 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 104-1/4 FSB 21 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 48-7/8 FDD 11 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 48-7/8 FDB 11 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-3/ For Buckets With Overall Widths Of 102-1/8" thru 104" Weld-On Base w/ends BB1-LR /2 x 12 x 106-1/4 FSB 22 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 12 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 26-13/16 FDD 5 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 12 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 26-13/16 FDB 5 1 x 2-3/ (continued) Pacal Blades Specifications 32 May 1, 2011

33 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 104-1/8" thru 106" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 108-1/4 FSB 22 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 12 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 27-13/16 FDD 5 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 12 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 27-13/16 FDB 5 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 106-1/8" thru 108" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 110-1/4 FSB 23 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 46-7/8 FDD 11 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 46-7/8 FDB 11 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 For Buckets With Overall Widths Of 108-1/8" thru 110" Terex: 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 112-1/4 FSB 23 Weld-On VME: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 46-7/8 FDD 11 1 x 2-3/ C, 175C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ L160, 275C Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ Kawasaki: Bolt-On Center BB1-LR /2 x 12 x 46-7/8 FDB 11 1 x 2-3/ KSS85Z11 Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-3/ KSS95Z Trojan: For Buckets With Overall Widths Of 110-1/8" thru 112" 4500Z, 5500Z 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 114-1/4 FSB 24 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 50-7/8 FDD 12 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 50-7/8 FDB 12 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-3/ For Buckets With Overall Widths Of 112-1/8" thru 114" Weld-On Base w/ends BB1-LR /2 x 12 x 116-1/4 FSB 24 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 50-7/8 FDD 12 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 50-7/8 FDB 12 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-3/ (continued) Pacal Blades Specifications 33 May 1, 2011

34 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 114-1/8" thru 116" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 118-1/4 FSB 25 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 54-7/8 FDD 13 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 54-7/8 FDB 13 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 116-1/8" thru 118" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 120-1/4 FSB 25 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 54-7/8 FDD 13 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 54-7/8 FDB 13 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 For Buckets With Overall Widths Of 118-1/8" thru 120" Terex: 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 122-1/4 FSB 26 Weld-On VME: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 58-7/8 FDD 14 1 x 2-3/ C, 175C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ L160, 275C Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 31-13/16 FDD 6 1 x 2-3/ Kawasaki: Bolt-On Center BB1-LR /2 x 12 x 58-7/8 FDB 14 1 x 2-3/ KSS85Z11 Bolt-On End R/L BB1-LR /2 x 12 x 31-13/16 FDB 6 1 x 2-3/ KSS95Z Trojan: For Buckets With Overall Widths Of 120-1/8" thru 122" 4500Z, 5500Z 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 124-1/4 FSB 26 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 58-7/8 FDD 14 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 32-13/16 FDD 6 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 58-7/8 FDB 14 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 32-13/16 FDB 6 1 x 2-3/ For Buckets With Overall Widths Of 122-1/8" thru 124" Weld-On Base w/ends BB1-LR /2 x 12 x 126-1/4 FSB 27 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 13 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 13 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ (continued) Pacal Blades Specifications 34 May 1, 2011

35 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 124-1/8" thru 126" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 128-1/4 FSB 27 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 52-7/8 FDD 13 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 52-7/8 FDB 13 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 126-1/8" thru 128" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 130-1/4 FSB 28 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 56-7/8 FDD 14 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 56-7/8 FDB 14 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 For Buckets With Overall Widths Of 128-1/8" thru 130" Terex: 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 132-1/4 FSB 28 Weld-On VME: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 56-7/8 FDD 14 1 x 2-3/ C, 175C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ L160, 275C Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Kawasaki: Bolt-On Center BB1-LR /2 x 12 x 56-7/8 FDB 14 1 x 2-3/ KSS85Z11 Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ KSS95Z Trojan: For Buckets With Overall Widths Of 130-1/8" thru 132" 4500Z, 5500Z 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 134-1/4 FSB 29 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 60-7/8 FDD 15 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 60-7/8 FDB 15 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ For Buckets With Overall Widths Of 132-1/8" thru 134" Weld-On Base w/ends BB1-LR /2 x 12 x 136-1/4 FSB 29 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 60-7/8 FDD 15 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 60-7/8 FDB 15 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ (continued) Pacal Blades Specifications 35 May 1, 2011

36 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 134-1/8" thru 136" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 138-1/4 FSB 30 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 64-7/8 FDD 16 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 64-7/8 FDB 16 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 136-1/8" thru 138" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 140-1/4 FSB 30 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 64-7/8 FDD 16 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB1-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 64-7/8 FDB 16 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 For Buckets With Overall Widths Of 138-1/8" thru 140" Terex: 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 142-1/4 FSB 31 Weld-On VME: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 68-7/8 FDD 17 1 x 2-3/ C, 175C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ L160, 275C Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Kawasaki: Bolt-On Center BB1-LR /2 x 12 x 68-7/8 FDB 17 1 x 2-3/ KSS85Z11 Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ KSS95Z Trojan: For Buckets With Overall Widths Of 140-1/8" thru 142" 4500Z, 5500Z 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 144-1/4 FSB 31 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 68-7/8 FDD 17 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 68-7/8 FDB 17 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ For Buckets With Overall Widths Of 142-1/8" thru 144" Weld-On Base w/ends BB1-LR /2 x 12 x 146-1/4 FSB 32 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 72-7/8 FDD 18 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 72-7/8 FDB 18 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ (continued) Pacal Blades Specifications 36 May 1, 2011

37 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 144-1/8" thru 146" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 148-1/4 FSB 32 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 72-7/8 FDD 18 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 72-7/8 FDB 18 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 146-1/8" thru 148" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 150-1/4 FSB 33 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 76-7/8 FDD 19 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 76-7/8 FDB 19 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 For Buckets With Overall Widths Of 148-1/8" thru 150" Terex: 70C, 80C Weld-On Base w/ends BB1-LR /2 x 12 x 152-1/4 FSB 33 Weld-On VME: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 76-7/8 FDD 19 1 x 2-3/ C, 175C Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ L160, 275C Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Kawasaki: Bolt-On Center BB1-LR /2 x 12 x 76-7/8 FDB 19 1 x 2-3/ KSS85Z11 Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ KSS95Z Trojan: For Buckets With Overall Widths Of 150-1/8" thru 152" 4500Z, 5500Z 7500C Weld-On Base w/ends BB1-LR /2 x 12 x 154-1/4 FSB 34 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 80-7/8 FDD 20 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 80-7/8 FDB 20 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ For Buckets With Overall Widths Of 152-1/8" thru 154" Weld-On Base w/ends BB1-LR /2 x 12 x 156-1/4 FSB 34 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 80-7/8 FDD 20 1 x 2-3/ Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ Bolt-On Center BB1-LR /2 x 12 x 80-7/8 FDB 20 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ (continued) Pacal Blades Specifications 37 May 1, 2011

38 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 154-1/8" thru 156" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR /2 x 12 x 158-1/4 FSB 35 Weld-On ,000 lb to 80,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 84-7/8 FDD 21 1 x 2-3/ /2" x 12" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x 2-3/ Caterpillar: 980C, 988B Bolt-On Center BB1-LR /2 x 12 x 84-7/8 FDB 21 1 x 2-3/ Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x 2-3/ Deere: 844 For Buckets With Overall Widths Of 156-1/8" thru 158" Dresser: H100C, H120C Weld-On Base w/ends BB1-LR /2 x 12 x 160-1/4 FSB 35 Weld-On , 560B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 84-7/8 FDD 21 1 x 2-3/ Fiatallis: Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ FR20B, FR30 Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x 2-3/ B, FR35 Bolt-On Center BB1-LR /2 x 12 x 84-7/8 FDB 21 1 x 2-3/ Komatsu: Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x 2-3/ WA420-1, WA450-1 WA470-1, WA500-1 Terex: 70C, 80C VME: 125C, 175C L160, 275C Kawasaki: KSS85Z11 KSS95Z Trojan: 4500Z, 5500Z 7500C Pacal Blades Specifications 38 May 1, 2011

39 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets With Overall Widths Of 150-1/8" thru 152" Weight Class of 80,000Lb to 160,000 lb Weld-On Base w/ends BB1-LR x 12-1/2 x 154-1/4 FSB 34 Weld-On " x 12-1/2" Base Bolt-On Center(MT Only) BB2-LR /4 x 10 x 80-7/8 FDD 20 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Caterpillar: Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x B Bolt-On Center BB1-LR /2 x 12 x 80-7/8 FDB 20 1 x Dresser: Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x H400C, 570 Komatsu: For Buckets With Overall Widths Of 152-1/8" thru 154" WA600-1 Weld-On Base w/ends BB1-LR x 12-1/2 x 156-1/4 FSB 34 Weld-On Terex: 90B Bolt-On Center(MT Only) BB2-LR /4 x 10 x 80-7/8 FDD 20 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x VME: Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x C, L320, 475C Bolt-On Center BB1-LR /2 x 12 x 80-7/8 FDB 20 1 x Kawasaki: Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x KSS110Z For Buckets With Overall Widths Of 154-1/8" thru 156" Weld-On Base w/ends BB1-LR x 12-1/2 x 158-1/4 FSB 35 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 84-7/8 FDD 21 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 84-7/8 FDB 21 1 x Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x For Buckets With Overall Widths Of 156-1/8" thru 158" Weld-On Base w/ends BB1-LR x 12-1/2 x 160-1/4 FSB 35 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 84-7/8 FDD 21 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 84-7/8 FDB 21 1 x Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x For Buckets With Overall Widths Of 158-1/8" thru 160" Weld-On Base w/ends BB1-LR x 12-1/2 x 162-1/4 FSB 36 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 88-7/8 FDD 22 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 88-7/8 FDB 22 1 x Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x (continued) Pacal Blades Specifications 39 May 1, 2011

40 Pacal Blades Bolt-On Cutting Edges for Loader Buckets Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. (continued) For Buckets With Overall Widths Of 160-1/8" thru 162" Loaders in the Weight Class of Weld-On Base w/ends BB1-LR x 12-1/2 x 164-1/4 FSB 36 Weld-On ,000Lb to 160,000 lb Bolt-On Center(MT Only) BB2-LR /4 x 10 x 88-7/8 FDD 22 1 x " x 12-1/2" Base Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Caterpillar: 992B Bolt-On Center BB1-LR /2 x 12 x 88-7/8 FDB 22 1 x Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x Dresser: H400C, 570 For Buckets With Overall Widths Of 162-1/8" thru 164" Komatsu: WA600-1 Weld-On Base w/ends BB1-LR x 12-1/2 x 166-1/4 FSB 37 Weld-On Terex: Bolt-On Center(MT Only) BB2-LR /4 x 10 x 92-7/8 FDD 23 1 x B Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x VME: 275C, L320, 475C Bolt-On Center BB1-LR /2 x 12 x 92-7/8 FDB 23 1 x Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x Kawasaki: KSS110Z For Buckets With Overall Widths Of 164-1/8" thru 166" Weld-On Base w/ends BB1-LR x 12-1/2 x 168-1/4 FSB 37 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 92-7/8 FDD 23 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 92-7/8 FDB 23 1 x Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x For Buckets With Overall Widths Of 166-1/8" thru 168" Weld-On Base w/ends BB1-LR x 12-1/2 x 170-1/4 FSB 38 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 96-7/8 FDD 24 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 36-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 96-7/8 FDB 24 1 x Bolt-On End R/L BB1-LR /2 x 12 x 36-13/16 FDB 7 1 x For Buckets With Overall Widths Of 168-1/8" thru 170" Weld-On Base w/ends BB1-LR x 12-1/2 x 172-1/4 FSB 38 Weld-On Bolt-On Center(MT Only) BB2-LR /4 x 10 x 96-7/8 FDD 24 1 x Bolt-On End RH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On End LH(MT Only) BB2-LR /4 x 10 x 37-13/16 FDD 7 1 x Bolt-On Center BB1-LR /2 x 12 x 96-7/8 FDB 24 1 x Bolt-On End R/L BB1-LR /2 x 12 x 37-13/16 FDB 7 1 x Pacal Blades Specifications 40 May 1, 2011

41 Pacal Blades Weld-On DoubleDuty Vee Edges Pacal Blades Blades Weld-On DoubleDuty Vee Systems are designed to increase bucket capacity and improve penetration ove conventional straight edges. Stresses on lifting arm assemblies are reduced by concentrating loads in the center of the bucket. The DoubleDuty replacement edge design offers the added shear strength and base edge protection needed for the most severe applications. DoubleDuty Vee Systems are ideal for loaders working in conjunction with crushing units, offering all the benefits of a vee edge without the worry of lost expendables. Made from abrasion and impact resistant steels, these edges are guaranteed to deliver long lasting economic value. To determine the correct cutting edge group, identify: 1) Machine class - Machine class is determined by weight or size. Listed in the left hand column of the selection guide are various models and weights of popular machines. If a specific machine is not listed, identify the class by using the approximate weight of the unit. 2) Bucket width - Bucket width is determined by measuring the bucket outside wall to outside wall. Base edges listed in this section are designed to allow the appropriate amount of overhang to accommodate weld-on corners listed in each section. * Edge assemblies do not include corners. ** All Pacal Blades Blades Lip Systems include a weld chamfer to facilitate installation. Note: For recommended welding procedures or details on how to take bucket measurements, refer to the General Information section of the Specification Guide. Pacal Blades Specifications 41 May 1, 2011

42 Qty. Length Wt./Lbs. Model Description Part No. Req'd. Dimensions of Bevel Approx. Loaders in the Weight Class of 84" Long Assembly with 9-7/8" Widths at End and 6-1/8" Projection, 1-3/8" x 8" Vee Edge 15,000lb to 26,000lb (1" Base) DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 16 x /2" 411 Case: DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x W14B, W20C, W24C Weld-On Cor RH BB1-LC x 7-5/8 x Weld-On Cor LH BB1-LC x 7-5/8 x Caterpillar 916, , B Deere: 96" Long Assembly with 8-7/8" Width at End and 7-1/8" Projection, 1-3/8" x 8" Vee Edge 444, 544D, 555B DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 16 x /2" 469 Dresser: H60, H65E DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x B, 520B Weld-On Cor RH BB1-LC x 7-5/8 x Weld-On Cor LH BB1-LC x 7-5/8 x Fiatallis: FR10B, FR11 FR12B Komatsu: WA150-1 WA " Long Assembly with 8" Width at End and 8" Projection, 1-3/8" x 8" Vee Edge WA300-1 DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 16 x /2" 525 Terex: 72-21B, 33C DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Weld-On Cor RH BB1-LC x 7-5/8 x VME: Weld-On Cor LH BB1-LC x 7-5/8 x L50, 45C, L70, 55C Kawasaki: KSS65Z Pacal Blades Weld-On DoubleDuty Vee Edges Trojan: 1500Z, 1900Z Loaders in the 96" Long Assembly with 10-7/8" Width at End and 7-1/8" Projection, 1-3/8" x 8" Vee Edge Weight Class of 26,000lb to 40,000lb DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 18 x 96 4" 585 (1-1/4" Base) DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Case: Weld-On Cor RH BB1-LC /4 x 8-5/8 x D, W26B, W30 Weld-On Cor LH BB1-LC /4 x 8-5/8 x Caterpillar 943, 950B 953, 955L 966C Deere: 644D 108" Long Assembly with 10" Width at End and 8" Projection, 1-3/8" x 8" Vee Edge Dresser: DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 18 x 108 4" 655 H70, H80, H90 530, 175C DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Weld-On Cor RH BB1-LC /4 x 8-5/8 x Fiatallis: Weld-On Cor LH BB1-LC /4 x 8-5/8 x FL10C, FR15B (models continued on next page) (continued) Pacal Blades Specifications 42 May 1, 2011

43 Pacal Blades Weld-On DoubleDuty Vee Edges Qty. Length Wt./Lbs. Model Description Part No. Req'd. Dimensions of Bevel Approx. (continued) (models continued from 120" Long Assembly with 9" Width at End and 9" Projection, 1-3/8" x 8" Vee Edge previous page) DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 18 x 120 4" 725 Komatsu: WA350-1 DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Weld-On Cor RH BB1-LV /4 x 8-5/8 x Terex: Weld-On Cor LH BB1-LC /4 x 8-5/8 x C, 60C VME: L90, 75C, L120 Kawasaki: KSS70Z Trojan: 2000Z, 3500Z Loaders in the 108" Long Assembly with 11" Width at End and 8" Projection, 1-3/8" x 8" Vee Edge Weight Class of 40,000lb to 80,000lb DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 19 x /4" 773 (1-1/2" Base) DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Case: Weld-On Cor RH BB1-LV /2 x 10 x B, W36 Weld-On Cor LH BB1-LC /2 x 10 x Caterpillar 963, 966D Deere " Long Assembly with 10" Width at End and 9" Projection, 1-3/8" x 8" Vee Edge Dresser: DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 19 x /4" 845 H100C, 540A 250E DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Weld-On Cor RH BB1-LC /2 x 10 x Fiatallis: Weld-On Cor LH BB1-LC /2 x 10 x FL14E FR20B Komatsu: WA400-1 WA " Long Assembly with 8-9/16" Width at End and 10-7/16" Projection, 1-3/8" x 8" Vee Edge Terex: 70C DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 19 x /4" 1000 VME: DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x C,175C, L160 Weld-On Cor RH BB1-LC /2 x 10 x Weld-On Cor LH BB1-LC /2 x 10 x Kawasaki: KSS85ZII Trojan: 4500Z Pacal Blades Specifications 43 May 1, 2011

44 Pacal Blades Weld-On DoubleDuty Vee Edges Qty. Length Wt./Lbs. Model Description Part No. Req'd. Dimensions of Bevel Approx. Loaders in the 138" Long Assembly with 12-9/16" Width at End and 10-7/16" Projection, 1-3/8" x 8" Vee Edge Weight Class of 40,000lb to 80,000lb DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 23 x 138 5" 1466 (2" Base) DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Caterpillar: Weld-On Cor RH BB1-LC x 10 x , 980C Weld-On Cor LH BB1-LC x 10 x Dresser H120C, 550 Fiatallis: FL20, FR30 138" Long Assembly with 13-7/8" Width at End and 10-7/16" Projection, 2-1/4" x 10" Vee Edge 945B DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 25 x 138-1/2 6-5/16" 1694 Komatsu: WA500 DoubleDuty Vee Edge(MT Only) BB2-LV /4 x 10 x Weld-On Cor RH BB1-LC x 10 x Terex: Weld-On Cor LH BB1-LC x 10 x C Kawasaki: 148" Long Assembly with 11-13/16" Width at End and 11-3/16" Projection, 1-3/8" x 8" Vee Edge KSS95Z DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 23 x 148 5" 1455 Trojan: 5500Z DoubleDuty Vee Edge(MT Only) BB2-LV /8 x 8 x Weld-On Cor RH BB1-LC x 10 x Weld-On Cor LH BB1-LC x 10 x " Long Assembly with 13-1/8" Width at End and 11-3/16" Projection, 2-1/4" x 10" Vee Edge DoubleDuty Vee Cutting Edge Assembly BB1-LV /8 x 20 x /16" 1784 DoubleDuty Vee Edge(MT Only) BB2-LV /4 x 10 x Weld-On Cor RH BB1-LC x 10 x Weld-On Cor LH BB1-LC x 10 x Pacal Blades Specifications 44 May 1, 2011

45 Pacal Blades DoubleDuty Vee w/bolt-on Edges Red indicated changes made since last published Pacal Blades Blades DoubleDuty Vee System w/bolt-on Edges are designed to provide quick replacement of cutting edges while increasing bucket capacity and penetration over conventional straight edges. The DoubleDuty Bolt-On design offers the added shear and edge protection needed for the most demanding jobs. Produced from industry leading alloys, Pacal Blades Blades DoubleDuty Vee Systems w/bolt-on Edges offer the convenience of bolt-ons with the strength of a vee. To determine the correct cutting edge group, identify: 1) Machine class - Machine class is determined by weight or size. Listed in the left hand column of the selection guide are various models and weights of popular machines. If a specific machine is not listed, identify the class by using the approximate weight of the unit. 2) Bucket width - Bucket width is determined by measuring the bucket outside wall to outside wall. Base edges listed in this section are designed to allow the appropriate amount of overhang to accommodate weld-on corners listed in each section. * Edge assemblies do not include corners. ** All Pacal Blades Blades Lip Systems include a weld chamfer to facilitate installation. Note: For recommended welding procedures or details on how to take bucket measurements, refer to the General Information section of the Specification Guide. Pacal Blades Specifications 45 May 1, 2011

46 Pacal Blades DoubleDuty Vee w/bolt-on Edges Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets with Overall Widths 104" thru 113-3/4" /2" Width at End and 8-1/2" Projection Weight Class of 26,000lb to 40,000lb DoubleDuty Vee Assembly BB1-LQ /8 x 21 x 114-1/4 - Weld-On Base thickness 1-1/2" Weld-On Cor R/L BB1-LO /2 x 7 x 9 - Weld-On - 19 Case: W24C, W26B DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x 2-3/ W30, W36 DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 35-29/ x 2-3/ DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 35-29/ x 2-3/ Caterpillar: B, 966C For Buckets with Overall Widths 114" thru 123-7/8" /8" Width at End and 9-3/8" Projection Deere: 644D DoubleDuty Vee Assembly BB1-LQ /8 x 21 x 124-1/8 - Weld-On Dresser: H80B Weld-On Cor R/L BB1-LO /2 x 7 x 9 - Weld-On - 19 H90C, 530B, 540A DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x 2-3/ Fiatallis: FR12B, FR15B DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 40-29/ x 2-3/ DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 40-29/ x 2-3/ Komatsu: WA300-1 WA320-1, WA350-1 WA380-1, WA400-1 For Buckets with Overall Widths 124" thru 133-1/2" /8" Width at End and 10-1/8" Projection Terex: 55C, 60C DoubleDuty Vee Assembly BB1-LQ /8 x 21 x Weld-On Weld-On Cor R/L BB1-LO /2 x 7 x 9 - Weld-On - 19 VME: L90, 75C, L120 DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x 2-3/ Kawasaki: KSS70Z DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 45-29/ x 2-3/ DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 45-29/ x 2-3/ Trojan: 2000Z, 3500Z Loaders in the For Buckets with Overall Widths 124" thru 133-1/2" /8" Width at End and 10-1/8" Projection Weight Class of 40,000lb to 80,000lb DoubleDuty Vee Assembly BB1-LQ /8 x 25 x Weld-On Base thickness 2" Weld-On Cor R/L BB1-LO x 8 x 9 - Weld-On - 32 Caterpillar: 980C, 988B DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 45-29/ x Deere:844 DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 45-29/ x Dresser: H100C H120C, 550, 560B For Buckets with Overall Widths 133-3/4" thru 143-3/8" /8" Width at End and 10-7/8" Projection Fiatallis: FR20B DoubleDuty Vee Assembly BB1-LQ /8 x 25 x 143-7/8 - Weld-On FR30, 945B, FR35 Weld-On Cor R/L BB1-LO x 8 x 9 - Weld-On - 32 Komatsu: WA420-1 DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x WA450-1, WA470-1 DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 50-29/ x WA500-1 DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 50-29/ x Terex: 70C, 80C For Buckets with Overall Widths 143-5/8" thru 153-1/4" /8" Width at End and 11-5/8" Projection VME: 125C, 175C L160, 275C DoubleDuty Vee Assembly BB1-LQ /8 x 25 x 153-3/4 - Weld-On Weld-On Cor R/L BB1-LO x 8 x 9 - Weld-On - 32 Kawasaki: KSS85ZII KSS95Z DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 55-29/ x Trojan: 4500Z DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 55-29/ x Z, 7500C Pacal Blades Specifications 46 May 1, 2011

47 Pacal Blades DoubleDuty Vee w/bolt-on Edges Qty. No. of Bolt Wt./Lbs. Model Description Part No. Req'd. Dimensions Holes Ea. Size Req'd. Approx. Loaders in the For Buckets with Overall Widths 153-1/2" thru 163-1/8" /16" Width at End and 12-7/16" Projection Weight Class of 40,000lb to 80,000lb DoubleDuty Vee Assembly BB1-LQ /8 x 25 x 163-5/8 - Weld-On Base thickness 2" Weld-On Cor R/L BB1-LO x 8 x 9 - Weld-On - 32 Caterpillar: 980C, 988B DoubleDuty Vee Bolt-On Center(MT Only) BB2-LQ /4 x 10 x 46-21/ x DoubleDuty Bolt-On End RH(MT Only) BB2-LQ /4 x 10 x 60-29/ x Deere:844 DoubleDuty Bolt-On End LH(MT Only) BB2-LQ /4 x 10 x 60-29/ x Dresser: H100C H120C, 550, 560B Fiatallis: FR20B FR30, 945B, FR35 Komatsu: WA420-1 WA450-1, WA470-1 WA500-1 Terex: 70C, 80C VME: 125C, 175C L160, 275C Kawasaki: KSS85ZII KSS95Z Trojan: 4500Z 5500Z, 7500C Pacal Blades Specifications 47 May 1, 2011

48 Pacal Blades Modified Vee Edges Special Application MaxTemp through hardened Vee edges are offered for maximum strength and to minimize cracking caused by welding, especially when tooth adapters are welded to the edge. Wt./Lbs. Part Number A B C D E F Bevel * Approx. BB2-LM / /4 49-1/2 1-1/4 blunt x BB2-LM / /4 47-1/2 1-1/4 blunt x BB2-LM / /4 blunt x BB2-LM /8 63-3/4 42-1/2 1-1/4 blunt x BB2-LM / / /4 47-1/2 1 blunt x BB2-LM / / blunt x BB2-LM / /8 63-3/4 42-1/2 1 blunt x BB2-LM / / /2 42 7/8 blunt x BB2-LM / / /2 42 7/8 blunt x BB2-LM /4 blunt x BB2-LM /8 52-1/2 35 3/4 blunt x BB2-LM / /2 34 3/4 blunt x BB2-LM / / /8 blunt x BB2-LM / / /8 blunt x BB2-LM / / /8 blunt x * Other blunts and angles can be furnished upon request. Available with heavy duty adapters & teeth mounted by Pacal Blades BLADES for maximum penetration. Pacal Blades Specifications 48 May 1, 2011

49 Pacal Blades Lip Assemblies Pacal Blades Lip Assemblies come fully dressed with bolt-on segments, weld-on adapters, fasteners, points and locks. Each base lip is made from Special Application Maxtemp offering unsurpassed impact resistance without sacrificing wear life. Lip Assemblies provide economic value over the purchase of individual component parts, and are guaranteed to provide long lasting economic value. Weld-On Mod Vee Base Edge Bolt-On Segment Cat Style DRP Long Point Cat Style DRP 2-Leg Adapter Note: For recommended welding procedures or details on how to take bucket measurements, refer to the General Information section of the Product Guide. Pacal Blades Specifications 49 May 1, 2011

50 Pacal Blades Lip Assemblies Qty. Assy. Make / Model Description Part No. Req. Dimensions Pins Locks Wt. Cat 980C Mod Vee Lip Assy BB2-LM x 26 x Weld-On Mod Vee Base Edge BB2-LM /4 x 26 x Bolt-On Segments Ctr 4T3015MT 1 1-3/16 x 14-3/16 x 10-1/ Bolt-On Segments RH 4T7139MT 3 1-3/16 x 14-3/16 x 15-9/ Bolt-On Segments LH 4T7140MT 3 1-3/16 x 14-3/16 x 15-9/ Cat Style DRP Flushmount Ctr Adapter 1U Cat Style DRP Flushmount RH Adapter 1U Cat Style DRP Flushmount LH Adapter 1U Cat Style DRP Long Point 1U W2678 3G Straight Lip Assy BB2-LS x 12 x Weld-On Base Edge BB2-LS /4 x 12 x Bolt-On Segments Ctr 4T3015MT 7 1-3/16 x 14-3/16 x 10-1/ Cat Style DRP Flushmount Ctr Adapter 1U Cat Style DRP Long Point 1U W2678 3G Cat 988B Mod Vee Lip Assy BB2-LM /8 x 28 x Weld-On Mod Vee Base Edge BB2-LM x 28 x Bolt-On Segments Ctr 9W5734MT 1 1-3/8 x 19 x 12-9/ Bolt-On Segments RH 9W5737MT 3 1-3/8 x 19 x 17-25/ Bolt-On Segments LH 9W5730MT 3 1-3/8 x 19 x 17-25/ Cat Style DRP 1-1/2 - Leg Ctr Adapter 4T Cat Style DRP 1-1/2 - Leg RH Adapter 4T Cat Style DRP 1-1/2 - Leg LH Adapter 4T Cat Style DRP Long Point 9W W8296 3G Straight Lip Assy BB2-LS /8 x 13 x Weld-On Base Edge BB2-LS x 13 x Bolt-On Segments Ctr 9W5734MT 7 1-3/8 x 19 x 12-9/ Cat Style DRP 1-1/2 - Leg Ctr Adapter 4T Cat Style DRP Long Point 9W W8296 3G Mod Vee Lip Assy BB2-LM /8 x 28 x Weld-On Mod Vee Base Edge BB2-LM x 28 x Bolt-On Segments Ctr 9W5734MT 1 1-3/8 x 19 x 12-9/ Bolt-On Segments RH 9W5737MT 3 1-3/8 x 19 x 17-25/ Bolt-On Segments LH 9W5730MT 3 1-3/8 x 19 x 17-25/ Cat Style DRP Flushmount Ctr Adapter 7T Cat Style DRP Flushmount RH Adapter 7T Cat Style DRP Flushmount LH Adapter 7T Cat Style DRP Long Point 9W W8296 3G Straight Lip Assy BB2-LS /8 x 13 x Weld-On Base Edge BB2-LS x 13 x Bolt-On Segments Ctr 9W5734MT 7 1-3/8 x 19 x 12-9/ Cat Style DRP Flushmount Ctr Adapter 7T Cat Style DRP Long Point 9W W8296 3G Pacal Blades Specifications 50 May 1, 2011

51 Pacal Blades Lip Assemblies Qty. Assy. Make / Model Description Part No. Req. Dimensions Pins Locks Wt. Cat 992C Mod Vee Lip Assy BB2-LM /2 x 36 x Weld-On Mod Vee Base Edge CA2-LM /2 x 36 x Bolt-On Segments Ctr 4T6760MT 1 1-1/2 x 12-1/4 x 16-1/ Bolt-On Segments RH 4T6761MT 3 1-1/2 x 23-1/4 x 23-29/ Bolt-On Segments LH 4T6762MT 3 1-1/2 x 23-1/4 x 23-29/ Cat Style DRP 2-Leg Ctr Adapter 3G Cat Style DRP 2-Leg RH Adapter 3G Cat Style DRP 2-Leg LH Adapter 3G Cat Style DRP Long Point 550APL 8-9W9026 8E Straight Lip Assy BB2-LS /2 x 21-1/2 x Weld-On Base Edge BB2-LS /2 x 21-1/2 x Bolt-On Segments Ctr 4T6760MT 7 1-1/2 x 23-1/4 x 16-1/ Cat Style DRP 2-Leg Ctr Adapter 3G Cat Style DRP Long Point 9W W9026 3G Pacal Blades Specifications 51 May 1, 2011

52 Pacal Blades Cutting Edges, Corners and Gussets for Loader and Backhoe Buckets Inside Corner Side Cutter Flat Single Bevel, Butt Welded Flat Single Bevel, Lap Welded 3 Pc. Wrap-Around Straight or Extended 1 Pc. Wrap-Around DoubleDuty, gives additional strength and rigidity to bottom of bucket, protects bucket sheet against abrasion wear, provides more steel at leading edge to take wear. Straight DoubleDuty welded to worn cutting edge that has been trimmed off square. Flush Type Corner Reinforcing Boot Extended Type Corner Reinforcing Boot 2 Pc. welded as shown. When bottom cutting edge is worn off, it is discarded and replaced. To rebuild and strengthen the entire bucket assembly, use Pacal Blades BLADES: A) One Piece cutting edge with straight, flush or extended corners installed over the cutting edge as corner reinforcing boots. Inside corner gussets at front and top of bucket. B) One piece wrap-around cutting edge with flush or extended corners installed over the cutting edge as corner reinforcing boots. Inside corner gussets at front and top of bucket. C) Three piece wrap-around cutting edge using either straight of extended corners. Extended corners give maximum wear life at this critical location. Inside corner gussets at front and top of bucket. Note: Wear plates or skid plates, welded to underside of bucket, improve cutting edge and bucket life. Pacal Blades Specifications 52 May 1, 2011

53 Pacal Blades ForgeTemp Carbon Steel Cutting Edges for Loaders and Backhoes Center cutting edge sections, listed below, may be used with either straight or extended type corners. Special one piece straight or wrap around cutting edges can also be supplied from these sections. These sections are available in any length up to the maximum length shown. Weight Per Foot Maximum Length Description Part No. Dimensions Lbs. Inches Blunt & Bevel Flat Single Bevel BB2-MS0355 3/8 x " 1/16 Blunt x 15.7º Flat Single Bevel BB1-MS0200 1/2 x " 1/16 Blunt x 22.1º Flat Single Bevel BB2-MS0353 1/2 x " 1/16 Blunt x 22.1º Flat Single Bevel BB1-MS0201 1/2 x " 1/16 Blunt x 23.6º Flat Single Bevel BB1-MS0202 5/8 x " 1/8 Blunt x 23.8º Flat Single Bevel BB1-MS0203 3/4 x " 1/8 Blunt x 22.6º Flat Single Bevel BB1-MS0204 3/4 x " 1/8 Blunt x 22.6º Flat Single Bevel BB1-MS x " 3/8 Blunt x 22.6º Flat Single Bevel BB1-MS x " 5/32 Blunt x 22.6º Flat Single Bevel BB1-MS /8 x " 5/32 Blunt x 22.6º Flat Single Bevel BB1-MS /4 x 10-1/ " 5/8 Blunt x 30º Flat Single Bevel BB1-MS /2 x " 1/2 Blunt x 30º Flat Single Bevel BB1-MS x 12-1/ " 5/8 Blunt x 30º Pacal Blades Specifications 53 May 1, 2011

54 Pacal Blades MaxTemp Heat Treated Cutting Edges for Loaders and Excavators MaxTemp through hardened cutting edges listed below are offered to minimize cracking caused by welding, especially when tooth adapters are welded to the cutting edge. Weight Per Foot Description Part No. Dimensions Lbs. Blunt & Bevel Flat Single Bevel BB2-MS1040 5/8 x /16 Blunt x 23 Flat Single Bevel BB2-MS1041 3/4 x /4 Blunt x 23 Flat Single Bevel BB2-MS1042 3/4 x /4 Blunt x 23 Flat Single Bevel BB2-MS x /4 Blunt x 23 Flat Single Bevel BB2-MS x /4 Blunt x 23 Flat Single Bevel BB2-MS x /4 Blunt x 23 Flat Single Bevel BB2-MS /4 x /2 Blunt x 23 Flat Single Bevel BB2-MS /8 x /2 Blunt x 23 Flat Single Bevel BB2-MS /2 x /2 Blunt x 30 Flat Single Bevel BB2-MS /4 x 10-1/ /2 Blunt x 23 Flat Single Bevel BB2-MS /4 x 10-1/ /8 Blunt x 30 Flat Single Bevel BB2-MS /4 x /2 Blunt x 23 Flat Single Bevel BB2-MS /2 x /2 Blunt x 30 Flat Single Bevel BB2-MS x 12-1/ /8 Blunt x 30 Flat DoubleDuty BB2-MS /8 x Flat DoubleDuty BB2-MS /4 x Flat DoubleDuty BB2-MS /4 x Note: Maximum available length is 156" Pacal Blades Specifications 54 May 1, 2011

55 Pacal Blades Corner Reinforcing Boots or Straight Corners for 3-Piece Wrap-Around Loader and Backhoe Cutting Edges Dimensions Part No. Cor T W H L A Use with Center Edge Weight BB1-LB0087 RH 1/ /2 4 1/2 x 6 FSB 8.0 BB1-LB0088 LH 1/ /2 4 1/2 x 6 FSB 8.0 BB1-LB0089 RH 5/ /2 4 5/8 x 6 FSB 8.3 BB1-LB0090 LH 5/ /2 4 5/8 x 6 FSB 8.3 BB1-LB0091 RH 3/ /2 4 3/4 x 6 FSB 9.5 BB1-LB0092 LH 3/ /2 4 3/4 x 6 FSB 9.5 BB1-LB0093 RH 3/ /4 x 8 FSB 15.0 BB1-LB0094 LH 3/ /4 x 8 FSB 15.0 BB1-LB0095 RH x 8 FSB 25.0 BB1-LB0096 LH x 8 FSB 25.0 BB1-LB0065 RH /4 1 x 9 FSB 27.0 BB1-LB0066 LH /4 1 x 9 FSB 27.0 BB1-LB0061 RH 1-3/ / /2 1-3/8 x 10 FSB 44.0 BB1-LB0062 LH 1-3/ / /2 1-3/8 x 10 FSB 44.0 BB1-LB0139 RH 1-3/4 10-1/2 9-3/ /2 1-3/4 x 10-1/2 FSB 72.0 BB1-LB0140 LH 1-3/4 10-1/2 9-3/ /2 1-3/4 x 10-1/2 FSB 72.0 BB1-LB0073 RH 1-1/ / /2 x 12 FSB 68.0 BB1-LB0074 LH 1-1/ / /2 x 12 FSB 68.0 BB1-LB0147 RH / /2 2 x 12-1/2 FSB BB1-LB0148 LH / /2 2 x 12-1/2 FSB BB1-LB0059 RH 1-1/ /4 x 8 FDD 19.0 BB1-LB0060 LH 1-1/ /4 x 8 FDD 19.0 BB1-LB0071 RH 1-3/ /8 x 8 FDD 22.0 BB1-LB0072 LH 1-3/ /8 x 8 FDD 22.0 BB1-LB0105 RH 2-1/ /4 x 10 FDD 59.0 BB1-LB0106 LH 2-1/ /4 x 10 FDD 59.0 Pacal Blades Specifications 55 May 1, 2011

56 Pacal Blades Corner Reinforcing Boots or Extended Corners for 3-Piece Wrap-Around Loader and Backhoe Cutting Edges Dimensions Part No. Cor T W H L A P Use with Center Edge Weight BB1-LB0107 RH 1/ / /2 x 6 FSB 7 BB1-LB0108 LH 1/ / /2 x 6 FSB 7 BB1-LB0109 RH 5/ / /8 x 6 FSB 9 BB1-LB0110 LH 5/ / /8 x 6 FSB 9 BB1-LB0111 RH 3/ / /4 x 6 FSB 10 BB1-LB0112 LH 3/ / /4 x 6 FSB 10 BB1-LB0113 RH 3/4 9-1/ /2 3/4 x 8 FSB 14 BB1-LB0114 LH 3/4 9-1/ /2 3/4 x 8 FSB 14 BB1-LB0115 RH 1 9-1/ /2 1 x 8 FSB 22 BB1-LB0116 LH 1 9-1/ /2 1 x 8 FSB 22 BB1-LB0117 RH / /4 1-3/4 1 x 9 FSB 28 BB1-LB0118 LH / /4 1-3/4 1 x 9 FSB 28 BB1-LB0119 RH 1-1/2 10-3/4 9-3/ / /8 x 10 FSB 44 BB1-LB0120 LH 1-1/ / / /8 x 10 FSB 44 BB1-LB0141 RH 1-3/4 12-1/2 9-3/ / /4 x 10-1/2 FSB 70 BB1-LB0142 LH 1-3/4 12-1/2 9-3/ / /4 x 10-1/2 FSB 70 BB1-LB0145 RH 1-1/2 14-1/2 9-3/ /2 1-1/2 x 12 FSB 72 BB1-LB0146 LH 1-1/2 14-1/2 9-3/ /2 1-1/2 x 12 FSB 72 BB1-LB0149 RH / /2 2-3/4 2 x 12-1/2 FSB 113 BB1-LB0150 LH / /2 2-3/4 2 x 12-1/2 FSB 113 BB1-LB0121 RH 7/8 9-1/ /2 1-1/4 x 8 FDD 24 BB1-LB0122 LH 7/8 9-1/ /2 1-1/4 x 8 FDD 24 BB1-LB0123 RH 1 9-1/ /2 1-3/8 x 8 FDD 27 BB1-LB0124 LH 1 9-1/ /2 1-3/8 x 8 FDD 27 BB1-LB0125 RH 1-1/4 11-1/ /2 2-1/4 x 10 FDD 51 BB1-LB0126 LH 1-1/4 11-1/ /2 2-1/4 x 10 FDD 51 Pacal Blades Specifications 56 May 1, 2011

57 Pacal Blades Corner Reinforcing Boots Flush Type Dimensions Part No. Section Thickness Length Weight BB1-LB0069 RH 3/ BB1-LB0070 LH 3/ BB1-LB0067 RH BB1-LB0068 LH BB1-LB0063 RH 1-3/ BB1-LB0064 LH 1-3/ BB1-LB0075 RH 1-1/ BB1-LB0076 LH 1-1/ Inside Corner Gussets for Loader and Backhoe Buckets Recommended Dimensions Part No. Bucket Size Thickness Length Weight BB1-LO0058 Under 3 Yd 1/ / BB1-LO to 6 Yd 3/4 17-7/ BB1-LO Yd Up / Pacal Blades Specifications 57 May 1, 2011

58 Special Application MaxTemp Cutting Edges for Excavators Special Application MaxTemp through hardened excavator edges are offered for maximum strength to resist impact breakage and to minimize cracking caused by welding. Special application MaxTemp may also be used on loader buckets where severe applications are encountered. Weight Per Foot Description Part No. Dimensions (Lbs.) Blunt & Bevel Flat Single Bevel BB2-MS x /8 Blunt x 30º Flat Single Bevel BB2-MS /2 x /2 Blunt x 30º Flat Single Bevel BB2-MS x /4 Blunt x 23º Flat Single Bevel BB2-MS /8 x /2 Blunt x 23º Flat Single Bevel BB2-MS /2 x /16 Blunt x 22.5º Flat Single Bevel BB2-MS /4 x /8 Blunt x 22.5º Flat Single Bevel BB2-MS x /4 Blunt x 22.5º Flat Single Bevel BB2-MS x /4 Blunt x 23º Flat Single Bevel BB2-MS /8 x /2 Blunt x 23º Flat Single Bevel BB2-MS /2 x /8 Blunt x 22º Flat Single Bevel BB2-MS /4 x /8 Blunt x 22º Flat Single Bevel BB2-MS x /4 Blunt x 22º Flat Single Bevel BB2-MS /4 x Blunt x 22.5º Flat Single Bevel BB2-MS /2 x Blunt x 22º Flat Single Bevel BB2-MS /2 x /8 Blunt x 22º Flat Single Bevel BB2-MS /4 x /16 Blunt x 22.5º Flat Single Bevel BB2-MS x /4 Blunt x 22º Flat Single Bevel BB2-MS /4 x /8 Blunt x 22º Flat Single Bevel BB2-MS /2 x Blunt x 22º Flat Single Bevel BB2-MS x /4 Blunt x 22º Flat Single Bevel BB2-MS /4 x /8 Blunt x 22º Flat Single Bevel BB2-MS /2 x Blunt x 22º Note: If edge is to accept tooth adapters, bevel and blunt must be specified at time of order. Pacal Blades Specifications 58 May 1, 2011

59 ForgeTemp Grader Cutting Edges Curved Double Bevel - Edges are State Highway Standard punching, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Pacal Blades Grader Cutting Edges Description Theoretical Mill Weight Per Linear Foot In Pounds 1/2" x 6" Curved Double Bevel 8.7 5/8" x 6" Curved Double Bevel /4" x 6" Curved Double Bevel /2" x 8" Curved Double Bevel /8" x 8" Curved Double Bevel 15.5 Heavy Duty Curved Double Bevel - Edges are State Highway Standard punching, modified with extra holes on 6" centers, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Heavy Duty cutting edges are recommended to increase wear life and minimize breakage. Description Theoretical Mill Weight Per Linear Foot In Pounds 3/4" x 8" Curved Double Bevel " x 8" Curved Double Bevel 25.3 Heavy Duty Flat Double Bevel - Edges are State Highway Standard punching, modified with extra holes on 6" centers, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Heavy Duty Flat Double Bevel cutting edges are recommended to increase wear life and minimize breakage when penetration and rolling of material is not of prime importance. Description Theoretical Mill Weight Per Linear Foot In Pounds 1-1/4" x 10" Flat Double Bevel 40.8 Pacal Blades Specifications 59 May 1, 2011

60 Pacal Blades Grader Cutting Edges ForgeTemp Grader Cutting Edges Curved Single Bevel - Edges are State Highway Standard punching, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Description Theoretical Mill Weight Per Linear Foot In Pounds 5/8" x 6" Curved Single Bevel /2" x 8" Curved Single Bevel /8" x 8" Curved Single Bevel 15.9 Curved No Bevel - Edges are State Highway Standard punching, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Description Theoretical Mill Weight Per Linear Foot In Pounds 5/8" x 6" Curved No Bevel 12.5 Surface Hardened Curved Single Bevel - Edges are State Highway Standard punching, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts, surface hardened to Rc a minimum of 1/8" deep. Hardened area approximately 5/8" from bottom of cutting edge and 3" high. Description Theoretical Mill Weight Per Linear Foot In Pounds 3/4" x 6" Curved Single Bevel /4" x 8" Curved Single Bevel 19.1 NOTE: For information on end bits, scarifier shanks, tips, model numbers and cutting edge sizes, refer to the applicable OEM section. Pacal Blades Specifications 60 May 1, 2011

61 Pacal Blades Grader MT Cutting Edges MaxTemp Grader Cutting Edges MaxTemp grader cutting edges are through-hardened for greater strength. For those tougher operations where breakage is a problem, MaxTemp cutting edges provide reduced labor cost and reduced downtime from changes. MaxTemp grader cutting edges are guaranteed against breakage under normal operating conditions. MaxTemp Curved Double Bevel - Edges are State Highway Standard punching, modified with extra holes on 6" centers, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Description Theoretical Mill Weight Per Linear Foot In Pounds 1/2" x 6" Curved Double Bevel 8.7 5/8" x 6" Curved Double Bevel /4" x 6" Curved Double Bevel /8" x 8" Curved Double Bevel /4" x 8" Curved Double Bevel " x 8" Curved Double Bevel " x 10" Flat Double Bevel /8" x 10" Flat Double Bevel " MaxTemp Serrated Curved Double Bevel - Edges are State Highway Standard punching, modified with extra holes on 6" centers, square countersunk holes for 5/8" cutting edge bolts, square ends, painted, without bolts. Only straight tooth cutting edges are offered.. Illustration of 5/8" x 6' Straight Tooth Serrated Cutting Edge. 30 Teeth - Straight 1-13/32" wide Space between teeth 1" Length of Teeth 2-3/8" Description Theoretical Mill Weight Per Linear Foot In Pounds 5/8" x 6" Curved Double Bevel 8.8 3/4" x 6" Curved Double Bevel 10.6 Pacal Blades Specifications 61 May 1, 2011