Ballooned by InspectionXpert. User: Brittany Belsito ; Expires: :33

Size: px

Start display at page:

Download "Ballooned by InspectionXpert. User: Brittany Belsito ; Expires: :33"

Ariel Daniel
5 years ago
Views:

2 REV SHEET 1 SPINDLE FITTING ASSEMBLY-LOCK LINK ATTACH, SIDE STRUT, MAIN THE PARTS LIST IN THIS REPORT SUPERSEDES THE DRAWING SHEET PARTS LIST FOR THIS PART OWNER LAND GEAR, C. REITZ, (425) PIN/ITEM REVISIONS... REV REVISION APPROVED CHANGE PHASE CLASS DESCRIPTION DATE NUMBER A PIN : NEW DRAWING. REASON: BASIC RELEASE. PIN PRODUCTION CHNG RESP: C. REITZ, (425) NOTE TITLE... PART SPECIFIC DATA... NOTE DESCRIPTION DRAWING 69B13372 SHEET 1 DRAWING 161W2328 SHEET 1 ZONE B4 FINISH - SEQUENCE 1 FL 1 161W2328 FL 5 161W2328 FL 6 161W2328 FL 7 161W2328 FL 8 161W F APPLY BMS 10-60, TYPE II, GLOSS ENAMEL, COLOR BAC 707 GRAY IN ACCORDANCE WITH BAC EXCEPT AS NOTED. INSTALLED DIMENSION. SIZE IF NECESSARY. SURFACE ROUGHNESS 63 MICROINCHES RA PER BACD INSTALL BUSHING BY SHRINK FIT WITH BMS 5-95 PER BAC FILLET SEAL BUSHING WITH BMS 5-95 PER 69B INSTALL THREADED LUBE INSERT BY SHRINK FIT WITH BMS 5-95 PER BAC INSERT TO BE INSTALLED FLUSH TO MACHINED PART SURFACE TO WITHIN PLUS OR MINUS INSTALL LUBE FITTING WITH BMS 3-33 GREASE TO INCH-POUNDS TORQUE. DO NOT APPLY ENAMEL TO INDICATED AREA, FEATURE, OR DETAIL. (CONTINUED ON NEXT PAGE) 9

3 REV SHEET 2 SPINDLE FITTING ASSEMBLY-LOCK LINK ATTACH, SIDE STRUT, MAIN (CONTINUED FROM PRECEDING PAGE) FL 9 161W2328 OPPOSITE PART 161W IS OPPOSITE TO 161W PROCESS SPECIFICATION TO ENSURE A CLEAR LUBRICATION PASSAGE AFTER BUSHING INSTALLATION, APPLY BMS 3-33 GREASE TO LUBE FITTING UNTIL GREASE APPEARS ON ID OF BUSHING BORE. RUBBER STAMP PART NUMBER PER BAC 5307, CODE RH. PROCESS SPECIFICATION SEE FLAGNOTE(S) OR PICTURE SHEET(S) FOR PROCESSING REQUIREMENTS PER BAC 5435 PROCESS SPECIFICATION 15 SEE FLAGNOTE(S) OR PICTURE SHEET(S) FOR PROCESSING REQUIREMENTS PER BACD COMPONENTS... QTY REQD PART OR IDENTIFYING DESCRIPTION NOTE TITLE NOTE DESCRIPTION NUMBER 1 161W SPINDLE ZONE/PAGE 1B3 FITTING-LOCK LINK 16 ATTACH, SIDE STRUT, MAIN 1 161W BUSHING-BUILD UP ZONE/PAGE 1C W BUSHING-BUILD UP ZONE/PAGE 1B W BUSHING-BUILD UP ZONE/PAGE 1A W BUSHING-BUILD UP ZONE/PAGE 1A W BUSHING-BUILD UP ZONE/PAGE 1B3 PARENTHESIS () INDICATES SUBSTITUTE PART (CONTINUED ON NEXT PAGE) 12 14

4 REV SHEET 3 SPINDLE FITTING ASSEMBLY-LOCK LINK ATTACH, SIDE STRUT, MAIN (CONTINUED FROM PRECEDING PAGE) 1 161W BUSHING-BUILD UP ZONE/PAGE 1B W THREADED INSERT - ZONE/PAGE 1C3 23 LUBE FITTING, 1 24 AS FITTING, LUBRICATION ZONE/PAGE 1C3 SUBSTITUTION AS HAS SUBSTITUTE MS (1 ) (MS ) LUBE FTG SUBSTITUTION MS IS A SUBSTITUTE FOR AS N BMS 3-33 GREASE VOLUME AS REQUIRED 1 NF990F BMS 5-95 KIT BMS 5-95 WET ANY BMS 5-95 MATERIAL TYPE AND MATERIAL CLASS B OR C INSTALLATION - MAY BE USED FOR INSTALLATION OF FASTENERS, BUSHINGS, 26 OPTIONAL RAW OR BEARINGS. MATERIALS VOLUME AS REQUIRED PARENTHESIS () INDICATES SUBSTITUTE PART

5 REV SHEET 4 SPINDLE FITTING ASSEMBLY-LOCK LINK ATTACH, SIDE STRUT, MAIN... STANDARD NOTES... NOTICE - THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO THE BOEING COMPANY AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART OR USED FOR ANY PURPOSE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM THE BOEING COMPANY. MATERIALS, PART & PROCESS SUBSTITUTION AND EQUIVALENTS PER 65B88700 (747), 012T2100 (767), 012W6100 (777), 012W6101 (EVERETT LIAISON) AND (ALL OTHERS). 27 FASTENER SYMBOL CODES PER BACD2074. INSTALL PER BAC5004 AND BAC5047 (FLUID TIGHT) SURFACE ROUGHNESS INTERPRETATION PER BACD2097. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. FOR DRAWING SHEETS DATED PRIOR TO 8/27/84: DIMENSIONING AND TOLERANCING PER ANSI Y FOR DRAWING SHEETS DATED ON OR AFTER 8/27/84: DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982, UNLESS OTHERWISE NOTED ON DRAWING SHEET. UNLESS OTHERWISE SPECIFIED, RIVET & BOLT EDGE MARGINS PLUS OR MINUS.05. UNLESS OTHERWISE SPECIFIED, BEND RADII SHALL BE PLUS OR MINUS.01 INCH ON MATERIAL THICKNESS BELOW.06 INCH AND PLUS OR MINUS.03 ON MATERIAL THICKNESS GREATER THAN.06 INCH. UNLESS OTHERWISE SPECIFIED, SHEET METAL CORNER RADII SHALL BE.16 INCH TO.19 INCH ON INTERNAL RADII AND.00 INCH TO.25 INCH ON EXTERNAL RADII. DIMENSIONS AND SURFACE TEXTURE DESIGNATIONS APPLY BEFORE PLATING OR FINISH COATING UNLESS OTHERWISE NOTED. 35 UNLESS OTHERWISE SPECIFIED, FABRICATION, ASSEMBLY, AND INSTALLATION SHALL CONFORM TO THE FOLLOWING: BAC5009 FOR INSTALLATION OF BOLTS AND NUTS. BAC5300 TO FORM, PUNCH, STRAIGHTEN, BREAK SHARP EDGES AND FIT METAL PARTS. BAC5307 FOR PART MARKING. BAC5602 FOR HEAT TREAT OF ALUMINUM ALLOYS

BEARING RACE- OUTER GROUP

BEARING RACE- OUTER GROUP MODEL PARTS SEATTLE, WA 98124 FSCM 81205 REV.DATE 3-08-93 PL 293W2514 C CONTRACT NUMBER SHT. 1OF MODEL 777 7497 PIN 2932-3100 2933-3100 DESIGN GROUP RESPONSIBILITY: H. HALLESY 234-9119... APPLICATION...