GYPSUM BOARD ASSEMBLIES

Transcription

1 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance criteria for gypsum board assemblies. B. Shaft wall system. C. Fire rated area separation walls. D. Acoustic insulation. E. Gypsum sheathing. F. Cementitious backing board. G. Gypsum wallboard. H. Glass mat faced gypsum board. I. Joint treatment and accessories. J. Textured finish system RELATED REQUIREMENTS A. Section Cold-Formed Metal Framing: Exterior wind-load-bearing metal stud framing. B. Section Rough Carpentry: Building framing and sheathing. C. Section Wood Blocking and Curbing: Wood blocking for support of wall-mounted equipment. D. Section Thermal Insulation: Acoustic insulation. E. Section Weather Barriers: Water-resistive barrier over sheathing. F. Section Joint Sealers: Acoustic sealant REFERENCE STANDARDS A. ANSI A American National Standard for Interior Installation of Cementitious Backer Units; 2010 (Revised). B. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes; C. ASTM C475/C475M - Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board; D. ASTM C514 - Standard Specification for Nails for the Application of Gypsum Board; 2004 (Reapproved 2014). E. ASTM C557 - Standard Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing; 2003 (Reapproved 2009). F. ASTM C665 - Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing; G. ASTM C840 - Standard Specification for Application and Finishing of Gypsum Board; H. ASTM C Standard Specification for Accessories For Gypsum Wallboard and Gypsum Veneer Base; 2014a. I. ASTM C1396/C1396M - Standard Specification for Gypsum Board; J. GA Application and Finishing of Gypsum Board; K. GA Application of Gypsum Board to Form Curved Surfaces; Gypsum Association; SYSTEM DESCRIPTION A. Acoustic Attenuation for Interior Partitions Indicated as Acoustic: STC of as indicated on plans calculated in accordance with ASTM E 413, based on tests conducted in accordance with ASTM E 90. B. Shaft Wall: Configure and install components as required to achieve the following performance levels: / Hilton Home2 West Palm GYPSUM BOARD ASSEMBLIES

2 HOME2 GUESTROOM FF&E SPECIFICATIONS - PALETTE B "TRIBECA" v1.0, May 2016 v1.1 - Revised February 2017 Unless otherwise noted as Required the following design intent specifications list Preferred Vendors whose use is not mandated. HILTON WORLDWIDE 755 CROSSOVER LANE, MEMPHIS, TN 38117

3 GUESTROOM FF&E SPECIFICATIONS PALETTE B "TRIBECA" Table of Contents Section Introduction/Supplemental Information 3 Item Index 5 Tagged Plans 7 Softgoods (100 series) 18 Lighting (200 series) 29 Casegoods (300 series) 40 Window Treatment (400 series) 79 Artwork / Mirrors (500 series) 86 Bedding (600 series) 92

4 GUESTROOM FF&E SPECIFICATIONS PALETTE B "TRIBECA" Introduction Within this document are the specifications needed to implement a Home2 Suites Brand guestroom scheme. Along with the Design Brief, the Home2 Suites Brand Standards Manual and the Architectural Prototype Drawings, these specifications will assist the designer in completing either a new build or renovation Home2 Suites Brand property. The specifications are dividied into two sections: Specifications and Finishes. The prototypical specifications coordinate with the current Home2 Suites Brand prototype room types. For renovations, designers will use the prototypical specifications. The finish portion provides specifications that act as a guide to selecting the materials needed for a complete guestroom. If there are any questions about how to use this document, any specific project needs or interpretation of prototypical specifications, please contact Architecture, Design & Construction at design.review@hilton.com All interior design submittals must be presented to Focus.Hilton.com for review prior to implementation.

5 GUESTROOM FF&E SPECIFICATIONS PALETTE B "TRIBECA" Supplemental Information The below documents can be found on the hiltonworldwide.com/design site (username and password are "hilton20xx", where XX is the current year). Design Brief: This document gives a designer all the reasons why the Brand is what it is. It helps establish uniformity of practice, consistently express the brand identity and serves as a guide for Interior Design and FF&E selection. This manual drills down even further with details on how to develop a Home2 Suites Brand guestroom and bath. It discusses the specific elements required and describes how the room design assists in letting the guest choose how the room functions. The Home2 Suites Standards Manual: This document lists the minimum standards, procedures, rules, regulations, policies and techniques required by the Home2 Suites Brand and Hilton Worldwide. Suppliers Connection: A list of recommended vendors are listed on Suppliersconnection.hilton.com Definitions Preferred Vendors: Unless marked as Required, Vendors listed herein are considered Preferred due to their efforts with HWW to develop specific items. While Preferred vendors have the necessary experience with specific products, an owner/designer may use a vendor of their choice outside the bounds of this list. Designer s Choice: For these items, the owner/designer may select based on individual design strategy using filters set forth by the Design Brief and the Home2 Suites Brand Standards. All items are subject to comment from Architecture, Design & Construction. PLEASE NOTE: It is the Owner s/designer s responsibility to maintain the design intent and adapt all required guestroom elements to their property s conditions prior to fabrication and installation.

6 GUESTROOM (GR) INDEX Issue Date: May 2016 PALETTE B "TRIBECA" Version: v2.2 Revision Date: February 2017 "GR" - previously "GF" Item Number Item Description Soft Seating (B) GR-100 Ottoman (B) GR Ottoman (B) GR-101 Sleeper Sofa (B) GR Sleeper Sofa (B) GR Fabric Sleeper Sofa (B) GR-102 Dining Chair (B) GR-103 Lounge Chair (B) GR Lounge Chair (B) GR-104 Task Chair REQUIRED Lighting (B) GR-200 (B) GR-201 (B) GR-202 (B) GR-203 (B) GR-203 ALT 1 (B) GR-204 (B) GR-205 (B) GR-206 (B) GR-207 (B) GR-208 Table Side Table Task Work Station Wall Headboard Vanity Guestroom Bathrooms Backlit Mirror Floor Sleeper Sofa End Wall Table Nightstand One Bedroom End Wall King Studio Accessible Casegoods (B) GR-300 Queen Headboard REQUIRED (B) GR Queen Headboard (B) GR-301 King Headboard REQUIRED (B) GR King Headboard (B) GR-302 Vanity REQUIRED (B) GR-303 Accessible Vanity REQUIRED (B) GR-304 Queen Studio Working Wall REQUIRED (B) GR-305 Queen Studio Connecting Working Wall REQUIRED (B) GR-306 Queen Studio Connecting - Accessible Working Wall REQUIRED (B) GR-307 Queen One Bedroom Working Wall REQUIRED (B) GR-308 Queen One Bedroom - Accessible Working Wall REQUIRED (B) GR-309 King Studio Working Wall REQUIRED (B) GR-310 Queen/Queen Studio Working Wall REQUIRED (B) GR-311 Queen/Queen Studio - Accessible Working Wall REQUIRED (B) GR-312 Queen/Queen Studio Connecting Working Wall REQUIRED (B) GR-313 King Studio Connecting - Accessible Working Wall REQUIRED (B) GR-314 King One Bedroom Working Wall REQUIRED (B) GR-315 King One Bedroom - Accessible Working Wall REQUIRED (B) GR-316 King Studio Connecting Working Wall REQUIRED

7 GUESTROOM (GR) INDEX Issue Date: May 2016 PALETTE B "TRIBECA" Version: v2.2 Revision Date: February 2017 "GR" - previously "GF" Item Number Item Description (B) GR-317 Nightstand REQUIRED (B) GR-318 Nesting Table REQUIRED (B) GR-319 Dining Table REQUIRED Drapery (B) GR-400 (B) GR-401 (B) GR-402 (B) GR-403 (B) GR-404 (B) GR-405 (B) GR-406 Artwork & Mirrors (B) GR-500 (B) GR-501 (B) GR-501 ALT 1 (B) GR-502 (B) GR-503 (B) GR-504 Roller Shade Roller Sheer Motorized Roller Shade Motorized Roller Sheer Room Divider Closet Drapery Accessible Closet Drapery Sleeper Sofa Dining Table Dining Table End Wall Framed vanity Guestroom Bathrooms Full Height Mirror Bedding (B) GR-600 Queen Boxspring Cover (B) GR Queen Boxspring Cover (B) GR ALT Queen Boxspring Cover (B) GR-601 King Boxspring Cover (B) GR King Boxspring Cover (B) GR ALT King Boxspring Cover (B) GR-602 Queen Bed Base (B) GR-603 King Bed Base (B) GR-604 Queen Coverlet REQUIRED (B) GR-605 King Coverlet REQUIRED (B) GR-606 Accessible Queen - Bedskirt (B) GR Accessible Queen Bedskirt (B) GR ALT Accessible Queen Bedskirt (B) GR-607 Accessible King - Bedskirt (B) GR Accessible King Bedskirt (B) GR ALT Accessible King Bedskirt

8 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen Studio Queen Studio

9 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen Studio Connecting Queen Studio Connecting

10 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen Studio Connecting- Accessible Queen Studio Accessible

11 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen One Bedroom Queen One Bedroom

12 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen One Bedroom Accessible Queen One Bedroom Accessible

13 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item King Studio King Studio

14 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen/Queen Studio Queen/Queen Studio

15 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen/Queen Studio Accessible Queen/Queen Studio Accessible

16 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Queen/Queen Studio Connecting- Accessible Queen/Queen Studio Connecting - Accessible

17 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item King Studio Connecting -Accessible King Studio-Accessible

18 Issue Date: May 2016 Area Name: Guestroom Revision Date: Item Working Wall Laminate Color Combinations Dark Base/Light Top Medium Base/Light Top One Color Working Wall

19 Issue Date: May 2016 Item Number: (B) GR-100 Area Name: Guestroom Item Ottoman Revision Date: Manufacturer: Marquis Seating Source: 231 South Road High Point, NC Phone: Phone: Fax: Fax: Contact: Ashleigh Reier Contact: Web: Web: Style: Round, upholstered ottoman with wood Guestrooms Sonnet Dimensions: Material/Finish: 24"Dia x 17.5"H Seat: COM Base: Ebony Cushion Style: Cushion Content: Tight Premium high-density, high resiliency foam with dacron wrap. Must pass NFPA 260 / CAL 117. COM: 3.5 yds / each GF Required Item(s) for Approval Prior to Fabrication: Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. No sag spring/foam construction. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as All foam, batting, padding, and dacron wrap shall be fire retardant to meet all applicable codes. COM quantities must be verified by fabricator. Entire frame and upholstery shall be inspected during the manufacturing and again after final assembly. Tailoring shall be neat, trim and performed in a professional manner. Manufacturer to include all necessary hardware with each item. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Insure that upholstered goods will fit in elevators and through doors prior to commencing fabrication. (B) GR 100

20 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Ottoman Revision Date: February 2017 Manufacturer: Fil Doux Textiles Source: 227 Fifth Avenue Brooklyn, NY Phone: Phone: Fax: Fax: Contact: Robert Pullen Contact: robert@fildoux.com Web: Web: Guestroom Ottomans Pattern: Color: Sincro.MER Jade 745 Width: Repeat: Content: 54" Surface: 100% Vinylife Backing: 100% Recycled Polyester Abrasion: Flammability: Backing: 200,000 double rubs NFPA260 (Available with ASTM E84 Treatment) 67% Polyester/ 33% Cotton Finish: Lightfastness: Soil/Stain Treatment: Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260. (B) GR 100.1

21 Issue Date: May 2016 Item Number: (B) GR-101 Area Name: Guestroom Item Sleeper Sofa Revision Date: February pages Manufacturer: Kellex Seating Brookline 101 Government Ave SW Hickory, NC Cheyenne Drive Archdale, NC Phone: ext Fax: Contact: Nancy Wilson Kristin Phillips nwilson@kellex.com kristin@brooklinefurniture.com Web: Style: Dimensions: SP Sleeper Sofa with 1/4" decorative Guestrooms Varies per Manufacturer Overall: 73"W x 36"D x 34"H Arm: 23"H Seat: 23"D x 20.5"H Material/Finish: Seat Cushion Style: Back Cushion Style: Frame: COM - Designer's choice Two (2) loose and reversible cushions with coil spring system inside cushion. Dacronwrapped 1.8 HR foam Tight with tufting Commercial Grade Hardwood. Corner blocked, glued, and screwed. Double doweled. Tight back. Sleeper Mechanism: Sleeper Mattress: COM: Leggett & Platt "Platinum X" Sleep System model Leggett & Platt Inner Spring with gel infused memory foam 13 yds / each (B) GF Glides included. Casters not included. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawing All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. No sag spring/foam construction. All upholstered furniture and its components must pass NFPA 260 Class 1. All foam, batting, padding, and dacron wrap shall be fire retardant to meet all applicable codes. COM quantities must be verified by fabricator. Entire frame and upholstery shall be inspected during the manufacturing and again after final assembly. Tailoring shall be neat, trim and performed in a professional manner. Manufacturer to include all necessary hardware with each item. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. (B) GR 101

22 Issue Date: May 2016 Item Number: (B) GR-101 Area Name: Guestroom Item Sleeper Sofa Revision Date: February pages Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Provide nylon carpet glides when applicable. Insure that upholstered goods will fit in elevators and through doors prior to commencing (B) GR 101

23 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Sleeper Sofa Revision Date: Manufacturer: Fil Doux Textiles Source: 227 Fifth Avenue Brooklyn, NY Phone: Phone: Fax: Fax: Contact: Robert Pullen Contact: robert@fildoux.com Web: Web: Guestroom Sleeper Sofas Pattern: Color: Port of Spain 7 Width: 54" Repeat: Content: Abraison: Flammability: Backing: 33% Polyester, 67% Acrylic 50,000 double rubs NFPA 260 Acrylic Finish: Lightfastness: Soil/Stain Treatment: Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 101.1

24 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Fabric Sleeper Sofa Revision Date: Manufacturer: Valley Forge Fabrics, Inc. Source: 1650 West McNab Road Fort Lauderdale, FL Phone: Phone: Fax: Fax: Contact: Contact: Jenna Tanner Web: Web: jtanner@valleyforge.com Fabric Guestroom Sleeper Sofas Pattern: Color: Rockstar Texture Crimson #IS22-60 Width: Repeat: Content: 54" 0"V x 0"H 100% Polyester, Abrasion: Flammability: Finish: Lightfastness: 50,000 double rubs NFPA 260 Grade 4-60 hours Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 101.2

25 Issue Date: May 2016 Item Number: (B) GR-102 Area Name: Guestroom Item Dining Chair Revision Date: Manufacturer: Sandler Seating Source: Waymire Contract LLC 1175 Peachtree St NE Suite 1850 Atlanta, GA SW Montclair Dr Portland, OR Phone: Phone: Fax: Fax: Contact: Contact: Dave Waymire Web: Web: Style: Dining chair with tapered wooden Guestrooms UNI 571-P Material/Finish: Body: Uni Mocca Legs: Beech Maple Dimensions: Overall: 18.9"W x 20.9"D x 31.1"H Seat: 18.1"H Body: Frame: Polypropylene Beechwood Seat meets BIFMAx5.1 strength test. Seat has padded-effect texture at front, glossy finish at back. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. No sag spring/foam construction. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as required by local and state fire codes for use in hotels and other public spaces. All foam, batting, padding, and dacron wrap shall be fire retardant to meet all applicable codes. COM quantities must be verified by fabricator. Entire frame and upholstery shall be inspected during the manufacturing and again after final assembly. Tailoring shall be neat, trim and performed in a professional manner. Manufacturer to include all necessary hardware with each item. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Provide nylon carpet glides when applicable. Insure that upholstered goods will fit in elevators and through doors prior to commencing fabrication. (B) GR 102

26 Issue Date: May 2016 Item Number: (B) GR-103 Area Name: Guestroom Item Lounge Chair Revision Date: Manufacturer: Marquis Seating Source: 231 South Road High Point, NC Phone: Phone: Fax: Fax: Contact: Ashleigh Reier Contact: Web: Web: Style: Lounge One Bedroom Accessible Suite Guestrooms Victoria Dimensions: Overall: 28"W x 34"D x 34"H Arm: 24.5"H Seat: 23"D x 18"H Material/Finish: Seat Cushion Style: COM: Body: COM Legs: Ebony Loose and tethered with D clips. Nylon zipper closure in casing. Cushions to be adequately vented for displacement of air and to provide increased comfort. 6.5 yds / each GF Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. No sag spring/foam construction. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as required by local and state fire codes for use in hotels and other public spaces. All foam, batting, padding, and dacron wrap shall be fire retardant to meet all applicable codes. COM quantities must be verified by fabricator. Entire frame and upholstery shall be inspected during the manufacturing and again after final assembly. Tailoring shall be neat, trim and performed in a professional manner. Manufacturer to include all necessary hardware with each item. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Insure that upholstered goods will fit in elevators and through doors prior to commencing fabrication. (B) GR 103

27 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Lounge Chair Revision Date: Manufacturer: Valley Forge Fabrics, Inc. Source: 1650 West McNab Road Fort Lauderdale, FL Phone: Phone: Fax: Fax: Contact: Contact: Jenna Tanner jtanner@valleyforge.com Web: Web: Guestroom Lounge Chairs Pattern: Color: Shutterbug Chenille Smoking Jacket AS10-16 Width: Repeat: Content: Abraison: Flammability: Backing: 54" None 82% Polyester, 18% Rayon 60,000 double rubs NFPA 260 Acrylic Finish: Lightfastness: Soil/Stain Treatment: Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 103.1

28 REQUIRED Issue Date: May 2016 Item Number: (B) GR-104 Area Name: Guestroom Item Task Chair Revision Date: February pages Manufacturer: Humanscale Corporation Source: 535 Anton Blvd, Suite 160 Costa Mesa, CA Phone: x 3123 Phone: Fax: Fax: Contact: Peter Hart Contact: phart@humanscale.com Web: Web: Style: Task Guestrooms Diffrient World Material/Finish: Frame: White Seat: HumanScale, Vellum 211 Beech Back: HumanScale, Pinstripe N74 Crimson Dimensions: Frame Content: Seat Cushion: Cushion Content: Seat Back: Overall: 26"W x 36.5"D x 41.5"H Arm: 23.8"-32"H (adjustable) Seat: 16.5"-20"D x 16"-21"H (adjustable) Injection-molded, structural, integral color grassfilled Nylon 6 Non-stretch mesh w/ frameless front edge; upholstered polyurethane foam seat cushion Form sensing non-stretch mesh upholstered over polyurethane foam seat cushion Form sensing non-stretch tri-panel mesh Required Item(s) for Approval Prior to Fabrication: Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. No sag spring/foam construction. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as required by local and state fire codes for use in hotels and other public spaces. All foam, batting, padding, and dacron wrap shall be fire retardant to meet all applicable codes. COM quantities must be verified by fabricator. Entire frame and upholstery shall be inspected during the manufacturing and again after final assembly. Tailoring shall be neat, trim and performed in a professional manner. Manufacturer to include all necessary hardware with each item. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. All welds to be finished and fully filled, ground smooth, no visible seams or burn marks. (B) GR 104

29 REQUIRED Issue Date: May 2016 Item Number: (B) GR-104 Area Name: Guestroom Item Task Chair Revision Date: February pages Insure that upholstered goods will fit in elevators and through doors prior to commencing fabrication. (B) GR 104

30 Issue Date: May 2016 Item Number: (B) GR-200 Area Name: Guestroom Item Table Side Table Revision Date: Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: sue@alisonandcompany.com Web: Web: Style: Dimensions: Clear glass table Side Table in Guestroom Living Spaces KTL20798 Overall: 14.5"Dia x 24.25"H Shade: 14.5"Dia x 8"H; Base: 7.5"Dia Finish: Clear Glass (body) with Satin Nickel (hardware/base) Central pipe painted to match Pantone 134C Switch Type: Cord Length: Cord Color: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Rocker Switch with Convenience Outlet 8'-0" Clear with polarized plug 27W self-ballasted lamp 60W Medium base socket 1 (not included) Trimless Tapered Drumshade w/ Self Fabric Top Diffuser with 5"Dia hole Homespun Ivory Linen Hardback ADA Compliant Power outlet to be on same side as rocker switch. Switch and power locations to be 180 degrees opposite of power cord for ease of use. Height of base to accommodate standard plug for ease of access. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. All guestroom table lamps with convenience outlets must have base switches, 8 foot black cord with polarized plugs and feltpadded base bottoms. Base must be weighted to prevent tipping. Power outlet to accommodate standard plug for ease of access. All switches and electrical power supply to match in color. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 200

31 Issue Date: May 2016 Item Number: (B) GR-200 Area Name: Guestroom Item Table Side Table Revision Date: Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: sue@alisonandcompany.co Web: Web: (B) GR 200.1

32 Issue Date: May 2016 Item Number: (B) GR-201 Area Name: Guestroom Item Task Work Station Revision Date: February 2017 Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: sue@alisonandcompany.com Web: Web: Style: Dimensions: Adjustable task Work Station in Guestrooms KTL21507 Overall: 9.5"W x 6"D x 15"H (center post: 14"H) Shade: 5"Dia x 4"H Base: 9.5"W x 6"D x 1"H Finish: Satin Nickel Switch Type: Cord Length: Cord Color: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Rocker Switch 8'-0" Custom Pantone #PMS 471C with polarized plug 25W self-ballasted lamp Type B-E 12 socket 1 (not included) Trimless Tapered Drumshade, No Diffuser Homespun Ivory Linen Hardback ADA Compliant Fixture to be wired with one (1) Type B-E 12 socket to be used with one (1) 25W self-ballasted lamp. Manufacturer to ensure stability. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. All guestroom table lamps with convenience outlets must have base switches, 8 foot black cord with polarized plugs and feltpadded base bottoms. Base must be weighted to prevent tipping. Power outlet to accommodate standard plug for ease of access. All switches and electrical power supply to match in color. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 201

33 Issue Date: May 2016 Item Number: Area Name: Guestroom Item Revision Date: Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: Web: Web: Style: Plug-in wall Nightstand/Headboard in Guestrooms KB20800 Dimensions: Overall: 15"W x 10"D x 13.5"H Shade: 15"W x 7"D x 7"H Backplate: 4.875"W x 1"D x 6.75"H Finish: Switch Type: Cord Length: Cord Color: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Mounting Satin Nickel ADAAG Toggle Switch 18" from end of cord cover 1/2" x 17" Satin Nickel cord cover 27W self-ballasted lamps 100W Medium base socket 2 (not included) Trimless Oval Drumshade, No Diffuser Homespun Ivory Linen Hardback ADA Compliant Fixture to be wall mounted; refer to elevations for mounting height. (B) GR-202 Wall Headboard Power outlet to accommodate standard plug for ease of access. Grounded cord set with polarized 90 degree plug with 45 degree offset. Installer to cut cord cover to length per field conditions or designer to coordinate mounting height. Cord cover to extend from sconce mounting plate to nightstand. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to confirm weight of fixture. Manufacturer/Fabricator to verify installation method and hanging points. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 202

34 Issue Date: May 2016 Item Number: Area Name: Guestroom Item Revision Date: Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA (B) GR-203 Vanity Fixture Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: Web: Web: Style: Dimensions: Finish: Vanity Guestroom Bathrooms KB "W x 3.5"D x 5.25"H Chrome Switch Type: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Weight: Mounting Hardwired LED 30W, 3000K, 120V 1 (included) Rectangular Satin Etched Cased Opal ADA Compliant 11lbs Fixture to be wall mounted; refer to elevations for mounting height. Refer to architectural drawings for the exact placement of the vanity light. Coordinate location of fixture's electrical feed with location of j-box and architectural field conditions. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to verify installation method and hanging points. All hardwired fixtures must have an electronic ballast. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 203

35 Issue Date: May 2016 Item Number: (B) GR-203 ALT 1 Area Name: Guestroom Item Backlit Mirror Revision Date: Manufacturer: Majestic Mirror Source: The Wright Group 7425 NW 79th St Miami, FL th Ave West Seattle, WA Phone: Phone: Fax: Fax: Contact: Adam Jaffe Contact: Denise Corso denise@thewrightgroupnw.com Web: Web: Style: Dimensions: Edge: Switch Type: Lamp Type: Lamp Wattage: Lamp Quantity: Mirror Backing: Orientation: ADA Compliant: Backlit Guestroom Bathrooms Custom Argyle with two vertical lines of light 42"W x 1.75"D x 36"H Polished Hardwired T5 LED Light Tube 17W, 3000K 2 (included) Vinyl Safety Backing Horizontal ADA Compliant Weight: 45lbs (approx.) Hardware: Mounting Fixture to be wall mounted; refer to elevations for mounting height. Refer to architectural drawings for the exact placement of the backlit mirror. Coordinate location of fixture's electrical feed with location of j-box and architectural field conditions. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to confirm weight of fixture. Manufacturer/Fabricator to verify installation method and hanging All hardwired fixtures must have an electronic ballast. All lamping must meet the requirements listed in the Home2 Suites standards manual. Installer responsible for the fixture to be mounted to a mechanically sound surface such as wall studs to support its Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 203 ALT 1

36 Issue Date: May 2016 Item Number: (B) GR-204 Area Name: Guestroom Item Floor Sleeper Sofa Revision Date: Manufacturer: Troy-CSL Lighting, Inc Nelson Ave City of Industry, CA Phone: Fax: Contact: Sue Alison sue@alisonandcompany.com Web: Style: Floor Sleeper Sofa in Guestrooms KFL20804 Dimensions: Overall: 20"W x 18.75"D x 57"H Shade: 4"Dia (top) x 6.125"Dia (bottom) x 10.25"H Finish: Switch Type: Cord Length: Cord Color: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Satin Nickel Rocker Switch on Post - 46" AFF 8'-0" Clear with polarized plug 42W self-ballasted lamp 100W Medium base socket 1 (not included) Trimless Conical Shade, No Diffuser Homespun Ivory Linen Hardback ADA Compliant Fixture to be wired with one (1) 100W Medium base socket to be used with one (1) 42W selfballasted lamp. Grounded cord set with polarized 90 degree plug with 45 degree offset. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. All floor lamps must have minimum 10# weighted bases of cast iron-fixed weight and must be sealed to prevent rust. Must have felt bottom. All lamps must have 8 foot clear cord with polarized plug. Power outlet to accommodate standard plug for ease of access. All switches and electrical power supply to match in All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 204

37 Issue Date: May 2016 Item Number: Area Name: Guestroom Item Revision Date: February 2017 Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: Web: Web: Style: Dimensions: Hardwired wall End Wall in Guestrooms KB Overall: 6"W x 4"D x 10"H Shade: 6"Dia Backplate: 5.75"Dia (B) GR-205 End Wall Finish: Switch Type: Lamp Type: Lamp Wattage: Lamp Quantity: Satin Nickel Hardwired 13W self-ballasted lamp, or med base LED lamp 60W Medium base socket 1 (not included) Shade/Diffuser Material: ADA Compliant: Mounting Oval Frosted White Glass ADA Compliant Fixture to be wall mounted; refer to elevations for mounting height. Refer to architectural drawings for the exact placement of the wall sconce. Coordinate location of fixture's electrical feed with location of j-box and architectural field conditions. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to confirm weight of fixture. Manufacturer/Fabricator to verify installation method and hanging points. All hardwired fixtures must have an electronic ballast. Must conform with Americans with Disabilities Act (ADA), Section 4.4, if applicable. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 205

38 Issue Date: May 2016 Item Number: (B) GR-206 Area Name: Guestroom Item Table Nightstand Revision Date: Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Contact: Sue Alison Contact: sue@alisonandcompany.com Web: Web: Style: Dimensions: Glass table Nightstand in Guestrooms KTL20807 Overall: 10"Dia x 18.6"H Shade: 10"Dia x 10.5"H Base: 9.3"Dia x 8"H Finish: Switch Type: Cord Length: Cord Color: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Coral Glass (base) with Satin Nickel (hardware) Rocker Switch with Convenience Outlet 8'-0" Black with polarized plug 27W self-ballasted lamp 60W Medium base socket 1 (not included) Trimless Drumshade Homespun Ivory Linen Hardback ADA Compliant USB port and power outlet to be on same side as rocker switch. Switch and power locations to be 180 degrees opposite of power cord for ease of use. Height of base to accommodate standard plug for ease of access. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. All guestroom table lamps with convenience outlets must have base switches, 8 foot black cord with polarized plugs and feltpadded base bottoms. Base must be weighted to prevent tipping. Power outlet to accommodate standard plug for ease of access. All switches and electrical power supply to match in color. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 206

39 Issue Date: May 2016 Item Number: Area Name: Guestroom Item Revision Date: February 2017 Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: Web: Web: Style: Dimensions: Hardwired wall End Wall in One Bedroom Guestrooms KB Overall: 5"W x 4"D x 10"H (B) GR-207 One Bedroom End Wall Finish: Switch Type: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Mounting Brass Hardwired 13W self-ballasted lamp, or med base LED lamp 60W Medium base socket 2 (included) As shown Cylindrical Frosted White Glass ADA Compliant Fixture to be wall mounted; refer to elevations for mounting height. Refer to architectural drawings for the exact placement of the wall sconce. Coordinate location of fixture's electrical feed with location of j-box and architectural field conditions. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to confirm weight of fixture. Manufacturer/Fabricator to verify installation method and hanging points. All hardwired fixtures must have an electronic ballast. Must conform with Americans with Disabilities Act (ADA), Section 4.4, if applicable. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 207

40 Issue Date: May 2016 Item Number: Area Name: Guestroom Item Revision Date: February 2017 Manufacturer: Troy-CSL Lighting, Inc. Source: Nelson Ave City of Industry, CA Phone: Phone: Fax: Fax: Contact: Sue Alison Contact: Web: Web: Style: Dimensions: Plug-in wall Sleeper Sofa in King Studio Accessible Guestrooms KB Overall: 5"W x 4"D x 10"H (B) GR-208 King Studio Accessible Finish: Switch Type: Lamp Type: Lamp Wattage: Lamp Quantity: Shade/Diffuser Style: Shade/Diffuser Material: ADA Compliant: Mounting Brass Rocker switch on backplate 13W self-ballasted lamp, or med base LED lamp 60W Medium base socket 2 (included) As shown Cylindrical Frosted White Glass ADA Compliant Fixture to be wall mounted; refer to elevations for mounting height. Refer to architectural drawings for the exact placement of the wall sconce. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Fixture must be U.L. Listed and so labeled. Manufacturer is responsible for submitting all technical specifications for fire safety, UL standards, and any other specifications that are required to comply with local and state fire codes. Manufacturer/Fabricator to confirm weight of fixture. Manufacturer/Fabricator to verify installation method and hanging points. All hardwired fixtures must have an electronic ballast. Must conform with Americans with Disabilities Act (ADA), Section 4.4, if applicable. All lamping must meet the requirements listed in the Home2 Suites standards manual. Show all pieces in scaled shop drawings. Entire fixture shall be inspected during the manufacturing and again after final assembly. (B) GR 208

41 REQUIRED Issue Date: May 2016 Item Number: (B) GR-300 Area Name: Guestroom Item Queen Headboard Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: Edge Detail: Direction of Grain: COM: Queen headboard with integrated side Guestrooms 79.5"W x "D x 37"H COM Plastic Laminate: Option A (Light): PL-2 Option B (Medium): PL-5 Option C (Dark): PL-8 1mm PVC Edgebanding to match Horizontal 2 yds / each (B) GR Installation: 20" AFF. Align top edge of nightstand ledge with top of mattress. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Headboard lamp to be located toward interior of room (away from window wall). Coordinate wire management notch that runs behind the headboard for mounting of wall sconce. Refer to architectural prototype drawings for additional information regarding orientation. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as required by local and state fire codes for use in hotels and other public spaces. Wall cleats are required for all headboards. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. (B) GR 300

42 REQUIRED Issue Date: May 2016 Item Number: (B) GR-300 Area Name: Guestroom Item Queen Headboard Revision Date: February pages COM quantities must be verified by fabricator. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 300

43 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Queen Headboard Revision Date: February 2017 Manufacturer: Fil Doux Textiles Source: 227 Fifth Avenue Brooklyn, NY Phone: Phone: Fax: Fax: Contact: Robert Pullen Contact: robert@fildoux.com Web: Web: Guestroom Queen Headboards Pattern: Color: Star Orange Width: 54" Repeat: Content: Surface: 100% Vinylife Backing: 100% Recycled Polyester Abrasion: Flammability: Backing: 200,000 double rubs NFPA260 (Available with ASTM E84 Treatment) Fabric is backed Finish: Lightfastness: Soil/Stain Treatment: Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260. (B) GR 300.1

44 REQUIRED Issue Date: May 2016 Item Number: (B) GR-301 Area Name: Guestroom Item King Headboard Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: King headboard with integrated side Guestrooms 95.5"W x "D x 37"H COM Plastic Laminate: Option A (Light): PL-2 Option B (Medium): PL-5 Option C (Dark): PL-8 Edge Detail: 1mm PVC Edgebanding to match Direction of Grain: Horizontal COM: 2 yds / each (B) GR Installation: 20" AFF. Align top edge of nightstand ledge with top of mattress. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Headboard lamp to be located toward interior of room (away from window wall). Coordinate wire management notch that runs behind the headboard for mounting of wall sconce. Refer to architectural prototype drawings for additional information regarding orientation. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. All upholstered furniture and its components must pass NFPA 260 Class 1. Upholstery foam shall be urethane foam cushioning certified to meet or exceed CAL 117E and CMHR barrier wrap as required by local and state fire codes for use in hotels and other public spaces. Wall cleats are required for all headboards. (B) GR 301

45 REQUIRED Issue Date: May 2016 Item Number: (B) GR-301 Area Name: Guestroom Item King Headboard Revision Date: February pages Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. COM quantities must be verified by fabricator. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval (B) GR 301

46 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item King Headboard Revision Date: February 2017 Manufacturer: Fil Doux Textiles Source: 227 Fifth Avenue Brooklyn, NY Phone: Phone: Fax: Fax: Contact: Robert Pullen Contact: robert@fildoux.com Web: Web: Guestroom King Headboards Pattern: Color: Star Orange Width: Repeat: Content: 54" None Surface: 100% Vinylife Backing: 100% Recycled Polyester Abrasion: Flammability: Backing: 200,000 double rubs NFPA260 (Available ASTM E84 Treatment) Fabric is backed Finish: Lightfastness: Soil/Stain Treatment: Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 301.1

47 REQUIRED Issue Date: May 2016 Item Number: (B) GR-302 Area Name: Guestroom Item Vanity Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: Base: Direction of Grain: Edge Details: Installation: Two drawer Guest Bathrooms 52"W x 23"D x 34"H Top: ST-01, provided by manufacturer Base: PL-05 Box Base Optional: Decorative Furniture Leg in lieu of Box Base Horizontal Interior Designer/Architect to coordinate blocking requirement. Manufacturer to determine method of attachment. Toilet tissue holder to be mounted to vanity in standard studio room types only. Construction should always use a marine grade plywood substrate. Interior of drawers and openings should be fully finished. Interior Designer/Architect to coordinate all plumbing with vanity and top. Refer to Home2 Suites Brand Standards for all plumbing requirements. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. All necessary corners to be reinforced with hardwood corner blocks. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. (B) GR 302

48 REQUIRED Issue Date: May 2016 Item Number: (B) GR-302 Area Name: Guestroom Item Vanity Revision Date: February pages Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval (B) GR 302

49 REQUIRED Issue Date: May 2016 Item Number: (B) GR-303 Area Name: Guestroom Item Accessible Vanity Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: Base: Accessible two drawer Guest Bathrooms 52"W x 23.5"D x 34"H Top: ST-01, provided by manufacturer Base: PL-05 Box Base Optional: Decorative Furniture Leg in lieu of Box Base Direction of Grain: Horizontal Edge Details: Installation: Interior Designer/Architect to coordinate blocking requirement. Manufacturer to determine method of attachment. Toilet tissue holder to be mounted to vanity in standard studio room types only. Construction should always use a marine grade plywood substrate. Interior of drawers and openings should be fully finished. Interior Designer/Architect to coordinate all plumbing with vanity and top. Refer to Home2 Suites Brand Standards for all plumbing requirements. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications for each property and in compliance to state and local codes. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. All necessary corners to be reinforced with hardwood corner blocks. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. (B) GR 303

50 REQUIRED Issue Date: May 2016 Item Number: (B) GR-303 Area Name: Guestroom Item Accessible Vanity Revision Date: February pages Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 303

51 REQUIRED Issue Date: May 2016 Item Number: (B) GR-304 Area Name: Guestroom Item Queen Studio Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.comwmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, drawer base, work station, mobile desk, knee space, and Queen Studio Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette A w/ Stone Top Drawer Base Work Station Mobile Desk (contrasting laminate) Wardrobe Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications for each property and in compliance to state and local codes. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. (B) GR 304

52 REQUIRED Issue Date: May 2016 Item Number: (B) GR-304 Area Name: Guestroom Item Queen Studio Working Wall Revision Date: February pages Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 304

53 REQUIRED Issue Date: May 2016 Item Number: (B) GR-305 Area Name: Guestroom Item Queen Studio Connecting Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, drawer base, work station, mobile desk, and Queen Studio Connecting Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL-02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Drawer Base Work Station Mobile Desk (contrasting laminate) Wardrobe Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications for each property and in compliance to state and local codes. (B) GR 305

54 REQUIRED Issue Date: May 2016 Item Number: (B) GR-305 Area Name: Guestroom Item Queen Studio Connecting Working Wall Revision Date: February pages All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 305

55 REQUIRED Issue Date: May 2016 Item Number: (B) GR-306 Area Name: Guestroom Item Queen Studio Connecting Accessible Working Revision Date: February 2017 Wall 2 pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Accessible Working Wall unit with ADA kitchenette, drawer base, work station, mobile desk, and ADA Accessible Studio Conneccting - Accessible Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette ADA w/ Stone Top Drawer Base Work Station Mobile Desk (contrasting laminate) Wardrobe ADA Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. (B) GR 306

56 REQUIRED Issue Date: May 2016 Item Number: (B) GR-306 Area Name: Guestroom Item Queen Studio Connecting Accessible Working Revision Date: February 2017 Wall 2 pages Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 306

57 REQUIRED Issue Date: May 2016 Item Number: (B) GR-307 Area Name: Guestroom Item Queen One Bedroom Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.comwmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, storage unit, work station, mobile desk, knee space, and Queen One Bedroom Guestrooms plus Working Wall with drawer base and Bedrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL-02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Storage Unit Work Station Mobile Desk (contrasting laminate) Wardrobe Bedroom Working Wall to include: Drawer Base Wardrobe Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings (B) GR 307

58 REQUIRED Issue Date: May 2016 Item Number: (B) GR-307 Area Name: Guestroom Item Queen One Bedroom Working Wall Revision Date: February pages Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 307

59 REQUIRED Issue Date: May 2016 Item Number: (B) GR-308 Area Name: Guestroom Item Queen One Bedroom - Accessible Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.comwmcarthus@solidcomfort.com david@foliot.com Web: Accessible Working Wall unit with kitchenette, storage unit, work station, and mobile Queen One Bedroom Accessible Guestrooms plus Accessible Working Wall with drawer base and Bedrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL-02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette ADA w/ Stone Top Storage Unit Work Station Mobile Desk (contrasting laminate) Bedroom Working Wall to include: Drawer Base Wardrobe ADA Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. (B) GR 308

60 REQUIRED Issue Date: May 2016 Item Number: (B) GR-308 Area Name: Guestroom Item Queen One Bedroom - Accessible Working Wall Revision Date: February pages All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 308

61 REQUIRED Issue Date: May 2016 Item Number: (B) GR-309 Area Name: Guestroom Item King Studio Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, drawer base, work station, mobile desk, knee space, storage unit, and King Studio Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Drawer Base Work Station Mobile Desk (contrasting laminate) Wardrobe Storage Unit Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. for each property and in compliance to state and local codes. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval (B) GR 309

62 REQUIRED Issue Date: May 2016 Item Number: (B) GR-309 Area Name: Guestroom Item King Studio Working Wall Revision Date: February pages prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for prior to production. (B) GR 309

63 REQUIRED Issue Date: May 2016 Item Number: (B) GR-310 Area Name: Guestroom Item Queen/Queen Studio Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, work station, mobile desk, knee space, drawer base, and Queen/Queen Studio Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL-02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Drawer Base Work Station Mobile Desk (contrasting laminate) Wardrobe Storage Unit Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. specifications (B) GR 310

64 REQUIRED Issue Date: May 2016 Item Number: (B) GR-310 Area Name: Guestroom Item Queen/Queen Studio Working Wall Revision Date: February pages All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 310

65 REQUIRED Issue Date: May 2016 Item Number: (B) GR-311 Area Name: Guestroom Item Queen/Queen Studio - Accessible Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Accessible Working Wall unit with ADA kitchenette, work station, mobile desk, knee space, drawer base, and ADA Queen/Queen Studio Accessible Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette ADA w/ Stone Top Knee Space Work Station Mobile Desk (contrasting laminate) Drawer Base Wardrobe ADA Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. (B) GR 311

66 REQUIRED Issue Date: May 2016 Item Number: (B) GR-311 Area Name: Guestroom Item Queen/Queen Studio - Accessible Working Wall Revision Date: February pages All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 311

67 REQUIRED Issue Date: May 2016 Item Number: (B) GR-312 Area Name: Guestroom Item Queen/Queen Studio Connecting Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.comwmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, work station, mobile desk, drawer base, and Queen/ Queen Studio Connecting Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top (substitute ADA Kitchenette in Accessible Rooms) Work Station Mobile Desk (headboard wall laminate to match mobile desk) Drawer Base Wardrobe (add ADA hanging 48"AFF in Accessible Rooms) Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. (B) GR 312

68 REQUIRED Issue Date: May 2016 Item Number: (B) GR-312 Area Name: Guestroom Item Queen/Queen Studio Connecting Working Wall Revision Date: February pages Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 312

69 REQUIRED Issue Date: May 2016 Item Number: (B) GR-313 Area Name: Guestroom Item King Studio Connecting Accessible Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Accessible Working Wall unit with ADA kitchenette, work station, mobile desk, drawer base, and King Studio Connecting Accessible Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets/Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette ADA w/ Stone Top Work Station Mobile Desk (contrasting laminate) Drawer Base Wardrobe ADA Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. (B) GR 313

70 REQUIRED Issue Date: May 2016 Item Number: (B) GR-313 Area Name: Guestroom Item King Studio Connecting Accessible Working Wall Revision Date: February pages Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 313

71 REQUIRED Issue Date: May 2016 Item Number: (B) GR-314 Area Name: Guestroom Item King One Bedroom Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, work station, mobile desk, knee space, drawer base, and King One Bedroom Guestrooms plus Working Wall with drawer base and Bedrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL-02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL-08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Work Station Mobile Desk (contrasting laminate) Drawer Base Knee Space Wardrobe Bedroom Working Wall to include: Drawer Base Wardrobe Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings (B) GR 314

72 REQUIRED Issue Date: May 2016 Item Number: (B) GR-314 Area Name: Guestroom Item King One Bedroom Working Wall Revision Date: February pages Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 314

73 REQUIRED Issue Date: May 2016 Item Number: (B) GR-315 Area Name: Guestroom Item King One Bedroom - Accessible Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Accessible Working Wall unit with ADA kitchenette, work station, mobile desk, and cabinet King One Bedroom Accessible Guestrooms plus Working Wall with drawer base and ADA Bedrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette ADA w/ Stone Top Work Station Mobile Desk (contrasting laminate) Cabinet Desk Bedroom Working Wall to include: Drawer Base Wardrobe ADA Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings (B) GR 315

74 REQUIRED Issue Date: May 2016 Item Number: (B) GR-315 Area Name: Guestroom Item King One Bedroom - Accessible Working Wall Revision Date: February pages Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 315

75 REQUIRED Issue Date: May 2016 Item Number: (B) GR-316 Area Name: Guestroom Item King Studio Connecting Working Wall Revision Date: February pages Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Working Wall unit with kitchenette, work station, mobile desk, storage unit, drawer base, and King Studio Connecting Guestrooms Finish: Edge Detail: Plastic Laminate Wood Finishes: Option A (Light): Working Wall Base Cabinet/Vertical Panels PL-03; Top Cabinets/Cubes PL-01; Mobile Desk PL- 02 Option B (Medium): Working Wall Base Cabinet/Vertical Panels PL-06; Top Cabinets Cubes PL-04; Mobile Desk PL-05 Option C (Dark): Working Wall Base Cabinet/Vertical Panels PL-07; Top Cabinets/ Cubes PL-09; Mobile Desk PL- 08 For All Options: Rear of Cubbies: PL-10 and PL-11; Rear of Cubbies at Kitchenette: PL-12; Kitchenette Counters: ST-01; Work Area Counters PL-13 1mm PVC Edgebanding to match Working Wall to include: Kitchenette w/ Stone Top Work Station Mobile Desk (contrasting laminate) Drawer Base Storage Unit Wardrobe Manufacturer to provide necessary support hanging hardware to support 250 lbs. minimum. Manufacturer responsible for method of attachment. Refer to prototype drawings for configurations and sourcing information. Architect and/or interior designer and manufacturer to verify right and left hand prior to fabrication. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. (B) GR 316

76 REQUIRED Issue Date: May 2016 Item Number: (B) GR-316 Area Name: Guestroom Item King Studio Connecting Working Wall Revision Date: February pages All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. Full extension, black coated ballbearing side mount slides, plywood 5-sided box drawer construction with white, stain resistant bottoms. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 316

77 REQUIRED Issue Date: May 2016 Item Number: (B) GR-317 Area Name: Guestroom Item Nightstand Revision Date: February 2017 Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: Edge Detail: Foot Detail: Guestrooms 24"Dia x 27.25"H Plastic Laminate: Option A (Light): PL-2 Option B (Medium): PL-5 Option C (Dark): PL-8 1mm PVC Edgebanding to match 1.5" nickel accent cap with neoprene glide Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 317

78 REQUIRED Issue Date: May 2016 Item Number: (B) GR-318 Area Name: Guestroom Item Nesting Table Revision Date: February 2017 Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Dimensions: Finish: Nesting Guestroom Sofas Large: 27"W x 15"D x 20"H Small: 23"W x 11.5"D x 17"H Plastic Laminate: Option A (Light): PL-2 Option B (Medium): PL-5 Option C (Dark): PL-8 Edge Detail: 1mm PVC Edgebanding to match Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 318

79 REQUIRED Issue Date: May 2016 Item Number: (B) GR-319 Area Name: Guestroom Item Dining Table Revision Date: February 2017 Manufacturer: D.R. Gilcrest, LLC Klem Hospitality Solid Comfort, Inc. Foliot Furniture Inc Lincoln Ave 755 S. Washington Ave th Ave S 721 Roland Godard Holland, MI Greenville, MS Fargo, ND Saint-Jerome, QC J7Y4C1 Phone: Contact: Rus Blondin Courtney Ayres Wayne McArthur David Foliot rb@drgilcrest.com courtney@klemgroup.com wmcarthus@solidcomfort.com david@foliot.com Web: Style: Dimensions: Finish: Edge Detail: Dining One Bedroom Suite Guestrooms Four-legged square dining table with inset top 36"W x 36"D x 30"H Legs: Dark Walnut Top: plastic laminate to match legs Wood Edge, Dark Walnut This is a knockdown (K/D) product. Legs to be installed on site. Tops to be attached to base per manufacturer's recommendation. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings Manufacturer to clearly mark each carton with item ID and specification number. All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative prior to production. Ensure that pieces will fit in elevators and through doors prior to commencing fabrication. Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping. Major joints as needed shall utilize lap joints or double doweled construction with corner blocks. Glue and staples are used to reinforce the joinery. Metal fasteners should be used where appropriate to ensure commercial frame strength. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. Provide clear alcohol and water resistant penetrating sealer as required. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. (B) GR 319

80 Issue Date: May 2016 Item Number: (B) GR-400 Area Name: Guestroom Item Roller Shade Revision Date: February pages Manufacturer: Hunter Douglas Hospitality Source: Addison Sales Group 5017 West Diablo Drive Las Vegas, NV Phone: Phone: Fax: Fax: Contact: Carol Addison Contact: Barry Addison carol.addison@hunterdouglas.co barryaddison@addisonsalesgroup.com Web: HDhospitality.com Web: Dimensions: RB 500 Manual blackout roller Guestrooms To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing and sizes. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing roller shade. Ceiling Height: Opening Size: Mounting Method: Components: Shade Style: Shade Dimensions: Chain: Fabric: Typ. 8'-0" VIF 3'-7"W x 6'-1"H VIF For outside mount at top of sill, provide 4" overlap on each side of opening. For inside mount, provide channel for minimal light leak. (1) Fascia: 3" Aluminum, Color: white, length: VIF (2) Side Channels and Brackets: SIN , white, extend to window sill (1) Clutch Hardware: RB-500, white Blackout Roller Shade 4'-1.25"W x 6'-4"H VIF Stainless steel beaded chain Hunter Douglas Lucca Blackout, Color: Pearl Green guard certified, 100% Polyester, acrylic finish, and treated with sanitized finish to resist mold/mildew Cords/Chains to be secured to control side of PTAC below with hold down brackets (VIF). Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for installation. All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet Class 1 ASTM E-84 and NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 400

81 Issue Date: May 2016 Item Number: (B) GR-401 Area Name: Guestroom Item Roller Sheer Revision Date: February 2017 Manufacturer: Hunter Douglas Hospitality Source: Addison Sales Group 5017 West Diablo Drive Las Vegas, NV Phone: Phone: Fax: Fax: Contact: Carol Addison Contact: Barry Addison Web: HDhospitality.com Web: Dimensions: RB 500 Manual sheer roller Guestrooms To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing and sizes. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing roller shade. Ceiling Height: Opening Size: Mounting Method: Components: Shade Style: Shade Dimensions: Chain: Fabric: Typ. 8'-0" VIF 3'-7"W x 6'-1"H VIF Inside mount behind blackout shade ((B) GR-400) RB 500 Clutch Hardware; no fascia or side channels required Sheer Roller Shade 4'-1.25"W x 6'-4"H VIF Stainless steel beaded chain Hunter Douglas Lumen Sheer, Color: White Green guard certified, 100% Polyester, 15% Openness Cords/Chains to be secured to control side of PTAC below with hold down brackets (VIF). Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for installation. All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet Class 1 ASTM E-84 and NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 401

82 Issue Date: May 2016 Item Number: (B) GR-402 Area Name: Guestroom Item Motorized Roller Shade Revision Date: February pages Manufacturer: Hunter Douglas Hospitality Source: Addison Sales Group 5017 West Diablo Drive Las Vegas, NV Phone: Phone: Fax: Fax: Contact: Carol Addison Contact: Barry Addison carol.addison@hunterdouglas.com barryaddison@addisonsalesgroup.com Web: HDhospitality.com Web: Dimensions: RB 500 Motorized blackout roller Accessible Guestrooms To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing and sizes. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing roller shade. Ceiling Height: Opening Size: Mounting Method: Motor: Components: Shade Style: Shade Dimensions: Fabric: Typ. 8'-0" VIF 3'-7"W x 6'-1"H VIF For outside mount at top of sill, provide 4" overlap on each side of opening. RTS motor with hardwired power cord and quick disconnect. Controlled by wireless wall switch(es). (1) Fascia: 3" Aluminum, white, length: VIF (2) Side Channels and Brackets: SIN , white, extend to window sill (1) Clutch Hardware: RB-500, white Blackout Roller Shade 4'-1.25"W x 6'-4"H VIF Hunter Douglas Lucca Blackout, Color: Pearl Green guard certified, 100% Polyester, acrylic finish, and treated with sanitized finish to resist mold/mildew Cords/Chains to be secured to control side of PTAC below with hold down brackets (VIF). Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for installation. All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet Class 1 ASTM E-84 and NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 402

83 Issue Date: May 2016 Item Number: (B) GR-403 Area Name: Guestroom Item Motorized Roller Sheer Revision Date: February 2017 Manufacturer: Hunter Douglas Hospitality Source: Addison Sales Group 5017 West Diablo Drive Las Vegas, NV Phone: Phone: Fax: Fax: Contact: Carol Addison Contact: Barry Addison Web: HDhospitality.com Web: Dimensions: RB 500 Motorized sheer roller Accessible Guestrooms To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing and sizes. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing roller shade. Ceiling Height: Opening Size: Mounting Method: Motor: Components: Shade Style: Shade Dimensions: Typ. 8'-0" VIF 3'-7"W x 6'-1"H VIF Inside mount behind blackout shade ((B) GR-402) RTS motor with hardwired power cord and quick disconnect. Controlled by wireless RB 500 Hardware; no fascia or side channels required Sheer Roller Shade 4'-1.25"W x 6'-4"H VIF Chain: Fabric: Stainless steel beaded chain Hunter Douglas Lumen Sheer, Color: White Green guard certified, 100% Polyester, 15% Openness Cords/Chains to be secured to control side of PTAC below with hold down brackets (VIF). Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for installation. All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet Class 1 ASTM E-84 and NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 403

84 Issue Date: May 2016 Item Number: (B) GR-404 Area Name: Guestroom Item Room Divider Revision Date: February 2017 Manufacturer: Focus Products Group Int'l, LLC Distributor: American Hotel Register 100 S. Milwaukee Ave Sysco Guest Supply, LLC 4301 US Highway One HD Supply Vernon Hills, IL P.O. Box 902 Monmouth Junction, NJ Phone: Fax: Contact: Web: Style: Dimensions: Fullness: Finished Length: Hemming: Mounting Method: Ceiling Height: Components: Top Treatment Style: Jeff White Kevin Trac Louis Cox Hookless "Berry Twist" Guestroom Room Dividers Operable room divider For 8' Ceilings: 129"W x 91.5"H For 9' Ceilings: 129"W x 103.5"H For 10' Ceilings: 129"W x 115.5"H Length based on 2.5" clearance for rod at top and 2" clearance at bottom. Manufacturer to verify all yardage and field measurements prior to manufacturing draperies. 150% 0.5" AFF 1" single side hems; 4" double bottom hem Pattern match all seams Ceiling Mounted Varies Ceiling Mounted Drapery Rod Source: Wingit; Dimensions: 7'-2" x 1"; Finish: Satin Stainless Steel Split top with 3"dia brushed stainless steel grommets Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 404

85 Issue Date: May 2016 Item Number: (B) GR-405 Area Name: Guestroom Item Closet Drapery Revision Date: February 2017 Manufacturer: Focus Products Group Int'l, LLC Distributor: American Hotel Register 100 S. Milwaukee Ave Vernon Hills, IL Sysco Guest Supply, LLC 4301 US Highway One P.O. Box 902 HD Supply Monmouth Junction, NJ Phone: Fax: Contact: Web: Jeff White Kevin Trac Louis Cox Style: Hookless "Berry Twist" Guestroom Closets Operable closet drapery Dimensions: (+/-) 60"W x 72"L To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing, sizes, and fabric yardage. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing draperies. Fullness: Finished Length: Hemming: 150% 1" AFF 5" single side hems; 2" double bottom hem Mounting Method: Ceiling Height: Components: Top Treatment Style: Side 6'-0" AFF Underside of closet: 6'-1.875" Stainless Steel Rod provided by casework manufacturer Domed Hookless Rings Finish: Brushed Stainless Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Closet drapery woven at widths to accommodate closet drapery only. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet Class 1 ASTM E-84 and NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 405

86 Issue Date: May 2016 Item Number: (B) GR-406 Area Name: Guestroom Item Accessible Closet Drapery Revision Date: February 2017 Manufacturer: Focus Products Group Int'l, LLC Distributor: American Hotel Register 100 S. Milwaukee Ave Vernon Hills, IL Sysco Guest Supply, LLC 4301 US Highway One P.O. Box 902 HD Supply Monmouth Junction, NJ Phone: Fax: Contact: Web: Jeff White Kevin Trac Louis Cox Style: Hookless "Berry Twist" Accessible Guestroom Closets Operable closet drapery Dimensions: (+/-) 72"W x 72"L To be field measured and confirmed by fabricator. Field measurements required for final confirmation of pricing, sizes, and fabric yardage. Drapery manufacturer to verify all yardage and field measurements prior to manufacturing draperies. Fullness: Finished Length: Hemming: 150% 1" AFF 5" single side hems; 2" double bottom hem Mounting Method: Ceiling Height: Components: Top Treatment Style: Side 6'-0" AFF Underside of closet: 6'-1.875" Stainless Steel Rod provided by casework manufacturer Domed Hookless Rings Finish: Brushed Stainless Must comply with ANSI standard for child safety, ANSI WCMA A100.1, Section 6.5. Closet drapery woven at widths to accommodate closet drapery only. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All quantity requirements must be verified by on-site. Measurements taken prior to fabrication. Fabricator is responsible for the size and quantity of all hardware to be used. Provide all hardware complete for All metal parts must be guaranteed rust, corrosion, and scratching resistant. Draperies must meet NFPA 701 Small and Large Scale as required by local and state fire codes for use in hotels. (B) GR 406

87 Issue Date: May 2016 Item Number: (B) GR-500 Area Name: Guestroom Item Sleeper Sofa Revision Date: Manufacturer: Wendover Art Group Source: 1510 Ellsworth Industrial Blvd Building One, Suite 400 Atlanta, GA Phone: Phone: Fax: Fax: Contact: Emily Duvoisin Contact: emily.duvoisin@wendoverart.com Web: Web: Publisher: Artwork above sleeper Guestrooms Wendover Art Title / Number: Dimensions: Frame: Mounting / Matting: Orientation: Hardware: Chevrons / A0213GP Overall: 24"W x 24"H Image: 24"W x 24"H 1.5" Stretcher Bar Stretched canvas with foam core backer to resist puncture Square 3-point security mounts See architectural prototype drawings for mounting height and location. When located at wet bar, artwork must be centered over clear counter space adjacent to sink. Refer to prototype drawings for location. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Digital Proof All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All artwork must be printed on or applied to acid free paper and dry mounted on a chip board or foam board as specified by designer. Moisture barrier tape must be applied to the back of the frame covering all metal staples. Theft-proof four point security hardware to be supplied by manufacturer and installed onto the back of all frames. Provide all parts, pieces and instructions for complete installation. Mounting method to be sufficient for weight of piece. All works must be free of mildew, pests or any infestation. Protection and treatment for any damage must be handled by a certified conservator. Source/Gallery must document damage and treatment/protection from further damage. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 500

88 Issue Date: May 2016 Item Number: (B) GR-501 Area Name: Guestroom Item Dining Table Revision Date: Manufacturer: Wendover Art Group Source: 1510 Ellsworth Industrial Blvd Building One, Suite 400 Atlanta, GA Phone: Phone: Fax: Fax: Contact: Emily Duvoisin Contact: emily.duvoisin@wendoverart.com Web: Web: Publisher: Dining Table in One Bedroom Guestroom Suites Wendover Art Style: Framed paper print Title / Number: Wondering West / A0120DK Dimensions: Overall: 30"W x 30"H Image: 25.75"W x 25.75"H Frame: Style: White or Satin Charcoal Dimensions:.875" W X 1.625"D Mount / Matting: Float mounting on off-white backer, 1.25" visible all sides; backing foam core; clear glass Orientation: Square Hardware: Security hardware See architectural prototype drawings for mounting height and location. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Digital Proof All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. All artwork must be printed on or applied to acid free paper and dry mounted on a chip board or foam board as specified by designer. Moisture barrier tape must be applied to the back of the frame covering all metal staples. Theft-proof four point security hardware to be supplied by manufacturer and installed onto the back of all frames. Provide all parts, pieces and instructions for complete installation. Mounting method to be sufficient for weight of piece. All works must be free of mildew, pests or any infestation. Protection and treatment for any damage must be handled by a certified conservator. Source/Gallery must document damage and treatment/protection from further damage. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 501

89 Issue Date: May 2016 Item Number: (B) GR-501 ALT 1 Area Name: Guestroom Item Dining Table Revision Date: Manufacturer: Wendover Art Group Source: 1510 Ellsworth Industrial Blvd Building One, Suite 400 Atlanta, GA Phone: Phone: Fax: Fax: Contact: Emily Duvoisin Contact: emily.duvoisin@wendoverart.com Web: Web: Publisher: Dining Table in One Bedroom Guestroom Suites Wendover Art Style: Framed paper print, matted Title / Number: Dharrmas / A0151HB Dimensions: Overall: 30"W x 30"H Image: 18.25"W x 18.25"H Frame: Style: White or Satin Charcoal Dimensions:.875" W X 1.625"D Mount / Matting: Orientation: Hardware: Foam core backing; clear glass, 5" mat on all sides Square Security hardware See architectural prototype drawings for mounting height and location. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Digital Proof All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. All artwork must be printed on or applied to acid free paper and dry mounted on a chip board or foam board as specified by designer. Moisture barrier tape must be applied to the back of the frame covering all metal staples. Theft-proof four point security hardware to be supplied by manufacturer and installed onto the back of all frames. Provide all parts, pieces and instructions for complete installation. Mounting method to be sufficient for weight of piece. All works must be free of mildew, pests or any infestation. Protection and treatment for any damage must be handled by a certified conservator. Source/Gallery must document damage and treatment/protection from further damage. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 501 ALT1

90 Issue Date: May 2016 Item Number: (B) GR-502 Area Name: Guestroom Item End Wall Revision Date: Manufacturer: Wendover Art Group Source: 1510 Ellsworth Industrial Blvd Building One, Suite 400 Atlanta GA Phone: Phone: Fax: Fax: Contact: Emily Duvoisin Contact: emily.duvoisin@wendoverart Web: Web: Publisher: End Wall Near Window in Double Queen Guestrooms Wendover Art Style: Framed paper print Title / Number: Blue Orbit / A0405DW Dimensions: Overall: 24"W x 30"H Image: 21.25"W x 27.25"H Frame: Mount / Matting: Orientation: Hardware: Style: Dark charcoal shadow box Dimensions:.875" W X 1.625"D Foam core backing; clear glass, 0.5" Mat on all sides Vertical Security hardware See architectural prototype drawings for mounting height and location. Required Item(s) for Approval Prior to Fabrication: Finish Sample, Digital Proof All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. All artwork must be printed on or applied to acid free paper and dry mounted on a chip board or foam board as specified by designer. Moisture barrier tape must be applied to the back of the frame covering all metal staples. Theft-proof four point security hardware to be supplied by manufacturer and installed onto the back of all frames. Provide all parts, pieces and instructions for complete installation. Mounting method to be sufficient for weight of piece. All works must be free of mildew, pests or any infestation. Protection and treatment for any damage must be handled by a certified conservator. Source/Gallery must document damage and treatment/protection from further damage. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 502

91 Issue Date: May 2016 Item Number: (B) GR-503 Area Name: Guestroom Item Vanity Mirror Revision Date: Manufacturer: Majestic Mirror Source: The Wright Group th Ave West 7425 NW 79th St Seattle, WA Miami, FL Phone: Phone: Fax: Fax: Contact: Adam Jaffe Contact: Denise Corso Web: Web: Style: Framed vanity Guestroom Bathrooms 3/16" Clear Float Mirror Dimensions: Overall: 42"W x 30"H x 1.5"D Mirror: 38"W x 26"H Edge: Frame: Clean Cut Polished; No Bevel Profile: Square Dimensions: 2"W x 1.5"D Finish: High Gloss White Mirror Backing: Orientation: Hardware: ANSI Safety Backed, corrugated sheet and moisture barrier tape Landscape Three point security hardware. One 27.5" (centered) and one security bracket (bottom) with corresponding wall hardware attached to back of mirror. See architectural prototype drawings for mounting height and location. Required Item(s) for Approval Prior to Fabrication: Finish Sample All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. other public spaces, and Home2 Suites Brand Standards. Manufacturer to clearly mark each carton with item ID and specification number. Provide three point or continuous cleat security cleating system appropriate for size and weight of mirror. Fabricator to provide all component parts for complete assembly and installation. Mounting method to be sufficient for weight of piece. Installer responsible for the fixture to be mounted to a mechanically sound surface such as wall studs to support its weight. Use clear float glass with 1/4" (6mm) backer sheet (Gator foam or tempered Masonite). For mirrors over 48"(1200mm) in any All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 503

92 Issue Date: May 2016 Item Number: (B) GR-504 Area Name: Guestroom Item Full Height Mirror Revision Date: Manufacturer: Majestic Mirror Source: The Wright Group 7425 NW 79th St Miami, FL th Ave West Seattle, WA Phone: Phone: Fax: Fax: Contact: Adam Jaffe Contact: Denise Corso Web: Web: Style: Full height Guestrooms 3/16" Clear Float Mirror Dimensions: Edge: Frame: Overall: 32"W x 76"H x 1"D Mirror: 24.5"W x 68.5"H 1" Bevel Profile: Square Dimensions: 3.75"W x 1."D Finish: High Gloss, match Benjamin Moore Gypsy Pink Mirror Backing: Orientation: Hardware: ANSI Safety Backed, corrugated sheet and moisture barrier tape Portrait Three point security hardware. One 23.5" cleat (top/centered) and 1 security bracket (bottom/centered) with corresponding wall hardware attached to back of mirror. See architectural prototype drawings for mounting height and location. Required Item(s) for Approval Prior to Fabrication: Finish Sample All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Provide three point or continuous cleat security cleating system appropriate for size and weight of mirror. Fabricator to provide all component parts for complete assembly and installation. Mounting method to be sufficient for weight of piece. Installer responsible for the fixture to be mounted to a mechanically sound surface such as wall studs to support its weight. Use clear float glass with 1/4" (6mm) backer sheet (Gator foam or tempered Masonite). For mirrors over 48"(1200mm) in any direction, provide inner frame and cross bracing. All pieces must be crated for shipping. All corners should be wrapped with corner guards. Crates should be labeled with instructions for shipment, storage and opening of crate. (B) GR 504

93 Issue Date: May 2016 Item Number: (B) GR-600 Area Name: Guestroom Item Queen Boxspring Cover Revision Date: Manufacturer: P/Kaufmann Contract Source: Billl Kramer & Associates 3 Park Ave, 34th Floor 8400 Wolf Lake Dr. Bartlett, New York, NY TN Phone: Phone: Fax: Fax: Contact: Contact: Toni Irvine tirvine@billkramer.net Web: Web: Style: Dimensions: Fitted boxspring Queen Guestrooms Custom Decorative 59"W x 79"D x 9"H; actual dimensions must be field verified due to size variations of boxspring Finish: Edge Detail: Decking Detail: Decking Content: Decking Color: COM: COM 1" turned, lock stitched hem with 1/2" elastic around all sides 4" wide fabric deck bands 50% Polyester, 50% Cotton White (B) GR Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. All fabrication, lining, and filler shall meet local fire and applicable codes. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260. (B) GR 600

94 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item Queen Boxspring Cover Revision Date: Manufacturer: P/Kaufmann Contract Source: Billl Kramer & Associates 3 Park Ave, 34th Floor New York, NY Wolf Lake Dr. Bartlett, TN Phone: Phone: Fax: Fax: Contact: Contact: Toni Irvine tirvine@billkramer.net Web: Web: Guestroom Queen Boxspring Covers Pattern: Color: C Hunting Tweed Sepia 841M Width: Repeat: Content: Abrasion: Flammability: Finish: 55" None 100% Polyester 50,000 double rubs NFPA 260 Brushed and Sanded Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 600.1

95 Issue Date: May 2016 Item Number: (B) GR ALT Area Name: Guestroom Item Queen Boxspring Cover Revision Date: February 2017 Manufacturer: Robert Allen Fabrics, Inc. Source: The Trump Group 225 Foxboro Blvd Foxboro, MA Phone: Phone: Fax: Fax: Contact: Contact: Sue Trump sue@thetrumps.com Web: Web: Pattern: Color: Guestroom Queen Boxspring Covers Herringbone A023 Heather Brown Width: 57" Repeat: None Content: Abrasion: Flammability: 100% Polyester Partial FR 30,000 DR NFPA 701 Required Item(s) for Approval Prior to Fabrication: Flame Certificate All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. All fabrication, lining, and filler shall meet local fire and applicable codes. (B) GR ALT

96 Issue Date: May 2016 Item Number: (B) GR-601 Area Name: Guestroom Item King Boxspring Cover Revision Date: Manufacturer: P/Kaufmann Contract Source: Billl Kramer & Associates 3 Park Ave, 34th Floor New York, NY Wolf Lake Dr. Bartlett, TN Phone: Phone: Fax: Fax: Contact: Contact: Toni Irvine tirvine@billkramer.net Web: Web: Style: Fitted boxspring King Guestrooms Custom Decorative Dimensions: Finish: Edge Detail: Decking Detail: Decking Content: Decking Color: COM: 75"W x 79"D x 9"H; actual dimensions must be field verified due to size variations of boxspring COM 1" turned, lock stitched hem with 1/2" elastic around all sides 4" wide fabric deck bands 50% Polyester, 50% Cotton White (B) GR Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. All fabrication, lining, and filler shall meet local fire and applicable codes. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260. (B) GR 601

97 Issue Date: May 2016 Item Number: (B) GR Area Name: Guestroom Item King Boxspring Cover Revision Date: Manufacturer: P/Kaufmann Contract Source: Billl Kramer & Associates 3 Park Ave, 34th Floor New York, NY Wolf Lake Dr. Bartlett, TN Phone: Phone: Fax: Fax: Contact: Contact: Toni Irvine tirvine@billkramer.net Web: Web: Guestroom King Boxspring Covers Pattern: Color: C Hunting Tweed Sepia 841M Width: Repeat: Content: Abrasion: Flammability: Finish: 55" None 100% Polyester 50,000 double rubs NFPA 260 Brushed and Sanded Provide treatment that increases durability/cleanability while maintaining good hand; a fabric with Nano-Tex, Crypton 2.0 or equal meets these requirements. Required Item(s) for Approval Prior to Fabrication: Cutting All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. COM quantities must be verified by fabricator. Fabric to have backing as required by fabricator and/or recommended by fabric supplier. Fabric must be treated for soil and stain repellency. Purchasing is responsible for FR treatment when fabric is not in compliance with applicable codes. FR treatment must not change quality or appearance of goods. Fabric must be first run goods from full bolts. Printing, dyeing, and finishing methods should be appropriate for use of fabric. All fabric must meet UFAC Class 1 and CAL 117E as required by local and state fire codes. All fabric must pass NFPA 260 (B) GR 601.1

98 Issue Date: May 2016 Item Number: (B) GR ALT Area Name: Guestroom Item King Boxspring Cover Revision Date: February 2017 Manufacturer: Robert Allen Fabrics, Inc. Source: The Trump Group 225 Foxboro Blvd Foxboro, MA Phone: Phone: Fax: Fax: Contact: Contact: Sue Trump sue@thetrumps.com Web: Web: Pattern: Color: Guestroom King Boxspring Covers Herringbone A023 Heather Brown Width: 57" Repeat: None Content: Abrasion: Flammability: 100% Polyester Partial FR 30,000 DR NFPA 701 Required Item(s) for Approval Prior to Fabrication: Flame Certificate All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. All fabrication, lining, and filler shall meet local fire and applicable codes. (B) GR ALT

99 Issue Date: May 2016 Item Number: (B) GR-602 Area Name: Guestroom Item Queen Bed Base Revision Date: February 2017 Manufacturer: Leggett & Platt Hospitality Source: P.O. Box Leggett Road Carthage, MO Phone: Phone: Fax: Fax: Contact: Phillip Herrin Contact: phillip.herrin@leggett.com Web: Web: Style: Dimensions: Finish: Bed base with retainer Queen Guestrooms # Q-17 Linwood Bed Base Box: 72" L, 49.5" W Dark Brown Walnut Woodgrain Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative for Entire frame shall be inspected during the manufacturing and again after final assembly. Metal fasteners should be used where appropriate to ensure commercial frame strength. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Manufacturer to include all necessary hardware with each item. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. Insure that pieces will fit in elevators and through doors prior to commencing fabrication. (B) GR 602

100 Issue Date: May 2016 Item Number: (B) GR-603 Area Name: Guestroom Item King Bed Base Revision Date: February 2017 Manufacturer: Leggett & Platt Hospitality Source: P.O. Box Leggett Road Carthage, MO Phone: Phone: Fax: Fax: Contact: Phillip Herrin Contact: phillip.herrin@leggett.com Web: Web: Style: Dimensions: Finish: Bed base with retainer King Guestrooms # K-17 Linwood Bed Base Box: 72" L, 65.5" W Dark Brown Walnut Woodgrain Required Item(s) for Approval Prior to Fabrication: Finish Sample, Shop Drawings All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. Manufacturer to clearly mark each carton with item ID and specification number. Show all pieces in shop drawings. Provide reproducible scaled shop drawings to Hotel Operator Representative for Entire frame shall be inspected during the manufacturing and again after final assembly. Metal fasteners should be used where appropriate to ensure commercial frame strength. Manufacturer to verify all necessary parts, hardware and dimensions required for assembly. Manufacturer to include all necessary hardware with each item. Solid hardwood frames to be certified sustainable sources. All stress joints to be connected by double doweled, screwed and glued corner reinforcement. All internal hardware (hinges, screws, bolts, etc.) shall be corrosion proof. All wood to be kiln dried and treated to be insect and vermin free. Finish goods containing composite wood products must comply with California Code of Regulations Product and carton will be labeled in accordance with this regulation. Manufacturer/Fabricator to provide Hotel Operator Representative with three 12"(30cm) x 12"(30cm) finish samples for approval prior to production. Insure that pieces will fit in elevators and through doors prior to commencing fabrication. (B) GR 603

101 REQUIRED Issue Date: May 2016 Item Number: (B) GR-604 Area Name: Guestroom Item Queen Coverlet Revision Date: February 2017 Manufacturer: Robert Allen Fabrics, Inc. Source: The Trump Group 225 Foxboro Blvd Foxboro, MA Phone: Phone: Fax: Fax: Contact: Contact: Sue Trump Web: Web: Style: Dimensions: Decorative coverlet with white cording, 16" back Queen Guestrooms Matelassé 92"W x 96"L Pattern (face and back): S022 Inner Circle Color (face and back): White Content: Hem: 100% Polyester Matelassé 2" retail hem at top and bottom; 2" flange on 3 sides Stitching: 8 SPI, single needle locked stitching; no chain stitching Edge Detail: Chamfered corners Required Item(s) for Approval Prior to Fabrication: N/A All interpretations of the specification MUST be submitted to Hilton Design Review (projecthub.hilton.com) for final approval prior to purchasing or implementation of any material. All fabrication, lining, and filler shall meet local fire and applicable codes. (B) GR 604