4344 SERIES HERMETIC SEALED THERMOSTATS

Size: px

Start display at page:

Download "4344 SERIES HERMETIC SEALED THERMOSTATS"

Buddy Barnard Francis
5 years ago
Views:

1 4344 SERIES HERMETIC SEALED THERMOSTATS Introduction The Klixon 4344 precision thermostat is constructed with a snap-acting bimetal disc, which serves as the actuating element. As the temperature reaches a pre-determined calibration point, the disc snaps to its reverse curvature producing a crisp, positive switching action inherent to Klixon thermostats. This feature assures reliable, consistent operating temperature over a long cycle life. The standard thermostat is copper-nickel plated with silver contacts. Other plating finishes are available upon request. Gold plated contacts can be furnished for the electrical loads listed in the table below to assure reliable circuit switching under low wattage conditions. Gold plated contacts are not suitable for higher loads. Our most common mounting configurations are depicted in the following pages. Many other varieties are available. Leads can be welded to pin type terminals to form an integral unit. The switch can be custom packed into a probe, strap mount, or immersion thermostat. Consult the factory for special requests. Features Snap-action switching Rapid thermal response Single pole, single throw Normally open or normally closed Pre-set, non adjustable calibration Switching Action All thermostats are supplied with single pole, single throw switching. The contacts can be constructed as: Normally Closed: Limit type application; contacts open on temperature rise at a predetermined temperature to de-engergize the circuit. Contacts automatically re-close as the device cools to a pre-determined temperature. Normally Open: Fan type application; contacts close on temperature rise at a predetermined temperature to energize the circuit. Contacts automatically reopen as the device cools to a predetermined temperature. The opening and closing temperatures are pre-set and non-adjustable. Page 1 Copyright 1 Sensata Technologies, Inc.

Typical Cross Section View Operation When heated, the internal stresses of the bi-metal cause the disc to reverse its curvature with a snap-action at a fixed, preset temperature and operate the

The disc returns to its normal curvature and the contacts assume their normal operating position.

2 Typical Cross Section View Operation When heated, the internal stresses of the bi-metal cause the disc to reverse its curvature with a snap-action at a fixed, preset temperature and operate the electrical contacts. A decrease in the ambient temperature below the reset temperature of the disc relieves the internal stresses in the disc. The disc returns to its normal curvature and the contacts assume their normal operating position. SPECIFICATIONS Performance Characteristics Switch Action Contact Resistance Contact Ratings SPST (Snap Action) 0.00 ohms maximum per MIL-STD-2, Method 7 VAC/DC VAC 20 VAC Based on standard differential Amperes Life Cycles 100,000 0,000 2,000 10,000,000 Dielectric Strength Vibration Resistance Shock Resistance Hermeticity Salt Spray Weight 0 VAC, rms, 60 Cycles for 1 minute, terminal to case, per MIL-STD-2, Method 1-00 Hm, G, per MIL-STD-2, Method 4 Condition D, (unmonitored) 100G, 6 milliseconds, per MIL-STD-2, Method x 10 - atm cc/sec. max per MIL-STD-2 Method 1, Condition C per MILD-STD-2, Method 101, Condition B, % solution Basic Unit with Bracket 4. grams. grams Page 2 Copyright 1 Sensata Technologies, Inc.

3 Gold Contact Ratings (Resistive) VAC/DC 00 ma and below 11 VAC 0 ma and below 2 VAC 100 ma and below Temperature Ambient Temperature Range Operating Temperature Tolerance -0 F to +0 F (-62.2 C to 27. C) Temperature at which normally closed contacts open or normally open contacts closed. Allowable range above and below setpoint and reset temperatures * An additional ±3 F tolerance is required for over molded devices. Differential Materials and Finish Standard Lead Connections Operating Temperature Differential Tolerance* F C F C F C Unplated 4 stainless for all new designs. (other finishes available upon request) Operating Temperature Differential Tolerance* F C F C F C Leads are available in heat-resistant rubber, neoprene, silicone-rubber and Teflon* in #11 gauge stranded wire in standard incremental lengths of 4" to 36". Other gauge and lengths are available upon request. * Trademark of E.I. Dupont de Nemours and Co. Page 3 Copyright 1 Sensata Technologies, Inc.

4 TYPICAL CONFIGURATIONS An additional ±3 F tolerance is required for over molded devices. All dimensions are in inches Page 4 Copyright 1 Sensata Technologies, Inc.

5 ZONE D REVISION DESCRIPTION ECN NO. "0 VAC" WAS " VAC"; PAF ECN OCT-07 CONFIGURATION 2 D MATERIAL: CONFIGURATION 1: COPPER-NICKEL PLATED CARBON STEEL CONFIGURATION 2: UNPLATED 4 STAINLESS STEEL DIELECTRIC STRENGTH: TERMINAL TO CASE, 0 VAC FOR 1 MINUTE C.6 MAX 2X BLIND HOLE.063/.047 X.04/.02 DEEP FLAT BOTTOM MAX B.62 FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. PARTS MADE TO THIS PRINT MUST CONFORM TO E99 E DRAWN CHAS. FLEURANT NEITHER THIS PRINT NOR THE INFORMATION CONTAINED HEREON IS TO BE USED AGAINST THE INTERESTS OF SENSATA TECHNOLOGIES OR 23-OCT-199 AGAINST THE INTERESTS OF ANY OF ITS AFFILIATED COMPANIES OR WHOLLY OWNED SUBSIDIARIES ENGINEER S.B. MARQUIS UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 23-OCT-199 TOLERANCES DECIMALS ANGLES Sensata Technologies TITLE THERMOSTAT SPST AUTO. RESET SEALED ENVELOPE DRAWING DWG NO. THIRD ANGLE SIZE PROJECTION DO NOT SCALE DRAWING B SCALE 2:1 SOLIDWORKS DEVICE: 4344 PROJECT: 26A PLEASANT STREET P.O. BOX 2964 ATTLEBORO, MA D SHEET 1 OF 1 A Page Copyright 1 Sensata Technologies, Inc.

6 ZONE REVISION DESCRIPTION ECN NO. C1 E "UNPLATED" WAS "UPLATED"; PD ECN OCT-0 D CONFIGURATION 2.6 MAX MATERIAL: CONFIGURATION 1: COPPER-NICKEL PLATED CARBON STEEL CONFIGURATION 2: UNPLATED 4L STAINLESS STEEL DIELECTRIC STRENGTH: C 2X X.04 DEEP FLAT BOTTOM.02 TERMINAL TO CASE, 0VAC, FOR 1 MINUTE B #6-32 UNC-2A THREAD FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. PARTS MADE TO THIS PRINT MUST CONFORM TO E99 E DRAWN C. FLEURANT 26-OCT-199 ENGINEER S. MARQUIS 26-OCT-199 NEITHER THIS PRINT NOR THE INFORMATION CONTAINED HEREON IS TO BE USED AGAINST THE INTERESTS OF SENSATA TECHNOLOGIES OR AGAINST THE INTERESTS OF ANY OF ITS AFFILIATED COMPANIES OR WHOLLY OWNED SUBSIDIARIES UNLESS OTHERWISE SPECIFIED TITLE DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGLES Sensata Technologies THERMOSTAT SPST AUTO RESET SEALED ENVELOPE DRAWING DWG NO. THIRD ANGLE SIZE PROJECTION DO NOT SCALE DRAWING B SCALE 2:1 SOLIDWORKS DEVICE: 4344 PROJECT: 26A PLEASANT STREET P.O. BOX 2964 ATTLEBORO, MA E SHEET 1 OF 1 A Page 6 Copyright 1 Sensata Technologies, Inc.

7 ZONE C1 REVISION DESCRIPTION ECN NO. E "UNPLATED" WAS "UPLATED"; PD ECN OCT-0 D CONFIGURATION 2 MATERIAL: CONFIGURATION 1: COPPER-NICKEL PLATED CARBON STEEL.6 MAX CONFIGURATION 2: UNPLATED 4L STAINLESS STEEL DIELECTRIC STRENGTH: TERMINAL TO CASE, 0VAC, FOR 1 MINUTE C 2X X.04 DEEP FLAT BOTTOM B FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. PARTS MADE TO THIS PRINT MUST CONFORM TO E99 E DRAWN CHAS. FLEURANT 14-MAY-1996 ENGINEER S. MARQUIS 14-MAY-1996 NEITHER THIS PRINT NOR THE INFORMATION CONTAINED HEREON IS TO BE USED AGAINST THE INTERESTS OF SENSATA TECHNOLOGIES OR AGAINST THE INTERESTS OF ANY OF ITS AFFILIATED COMPANIES OR WHOLLY OWNED SUBSIDIARIES UNLESS OTHERWISE SPECIFIED TITLE DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGLES Sensata Technologies THERMOSTAT SPST AUTO. RESET SEALED ENVELOPE DRAWING DWG NO. THIRD ANGLE SIZE PROJECTION DO NOT SCALE DRAWING B SCALE 2:1 SOLIDWORKS DEVICE: 4344 PROJECT: 26A PLEASANT STREET P.O. BOX 2964 ATTLEBORO, MA E SHEET 1 OF 1 A Page 7 Copyright 1 Sensata Technologies, Inc.

8 ZONE C1 B "UNPLATED" WAS "UPLATED"; PD REVISION DESCRIPTION ECN NO. ECN OCT-0 D CONFIGURATION 2.6 MAX. MATERIAL: X.04/.02 DEEP FLAT BOTTOM.047 CONFIGURATION 1: COPPER-NICKEL PLATED CARBON STEEL CONFIGURATION 2: UNPLATED 4L STAINLESS STEEL C DIELECTRIC STRENGTH: TERMINAL TO CASE, 0VAC, FOR 1 MINUTE 2X AWG 1 TEFLON WIRE TBD B #6-32 UNC-2A THREAD FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. PARTS MADE TO THIS PRINT MUST CONFORM TO E99 E DRAWN PD 02-OCT-06 ENGINEER NEITHER THIS PRINT NOR THE INFORMATION CONTAINED HEREON IS TO BE USED AGAINST THE INTERESTS OF SENSATA TECHNOLOGIES OR AGAINST THE INTERESTS OF ANY OF ITS AFFILIATED COMPANIES OR WHOLLY OWNED SUBSIDIARIES UNLESS OTHERWISE SPECIFIED Sensata Technologies THERMOSTAT SPST AUTO RESET SEALED ENVELOPE DRAWING S. MARQUIS DIMENSIONS ARE IN INCHES 02-OCT-06 TOLERANCES DECIMALS ANGLES P.BERG 02-OCT-06 DWG NO. THIRD ANGLE SIZE D.PETRIE PROJECTION 02-OCT-06 DO NOT SCALE DRAWING B SCALE 2:1 SOLIDWORKS 3 2 DEVICE: 4344 PROJECT: 26A 1 TITLE 29 PLEASANT STREET P.O. BOX 2964 ATTLEBORO, MA B SHEET 1 OF 1 A Page Copyright 1 Sensata Technologies, Inc.

9 Page 9 Copyright 1 Sensata Technologies, Inc.

10 Page 10 Copyright 1 Sensata Technologies, Inc.

11 ZONE 2 REVISION DESCRIPTION 1 ECN NO. C ADDED CONFIGURATION; GML ECN OCT-06 CONFIGURATION 2 D R HOLE C MAX REF. B FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. PARTS MADE TO THIS PRINT MUST CONFORM TO E99 E DRAWN CHAS. FLEURANT 7-MAY-1996 ENGINEER S.B. MARQUIS 7-MAY-1996 NEITHER THIS PRINT NOR THE INFORMATION CONTAINED HEREON IS TO BE USED AGAINST THE INTERESTS OF SENSATA TECHNOLOGIES OR AGAINST THE INTERESTS OF ANY OF ITS AFFILIATED COMPANIES OR WHOLLY OWNED SUBSIDIARIES UNLESS OTHERWISE SPECIFIED TITLE DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGLES Sensata Technologies THERMOSTAT SPST AUTO, RESET SEALED ENVELOPE DRAWING DWG NO C THIRD ANGLE SIZE PROJECTION DO NOT SCALE DRAWING B SCALE 2:1 SOLIDWORKS DEVICE: PROJECT: 26A PLEASANT STREET P.O. BOX 2964 ATTLEBORO, MA SHEET 1 OF 1 A Page 11 Copyright 1 Sensata Technologies, Inc.

AGENCY APPROVALS AND CERTIFICATIONS UL File No. 3461 CSA File No.

12 AGENCY APPROVALS AND CERTIFICATIONS UL File No CSA File No. LR244 WARNINGS RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE The product s side panels may be hot, allow the product to cool before touching Follow proper mounting instructions including torque values Do not allow liquids or foreign objects to enter this product Failure to follow these instructions can result in serious injury, or equipment damage. HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Disconnect all power before installing or working with this equipment Verify all connections and replace all covers before turning on power Failure to follow these instructions will result in death or serious injury Page Sensata Technologies, Inc. ( Sensata ) data sheets are solely intended to assist designers ( Buyers ) who are developing systems that incorporate Sensata products (also referred to herein as components ). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice. Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED AS IS. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF. All products are sold subject to Sensata s terms and conditions of sale supplied at SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 29 Pleasant Street, Attleboro, MA 02703, USA. Copyright 1 Sensata Technologies, Inc. Rev:03/29/1 CONTACT US Americas +1 () sensors@sensata.com Europe, Middle East & Africa +31 (74) Asia Pacific sales.isasia@list.sensata.com China +6 (21) Japan +1 (4) Korea +2 (31) India +91 (0) Rest of Asia +6 (2) ext 20

MHM5 SERIES ETHERNET/IP ABSOLUTE MULTI -TURN ENCODER

MHM5 SERIES ETHERNET/IP ABSOLUTE MULTI -TURN ENCODER Features Robust and compact design Solid shaft version Ø 10mm standard, with Ø 6mm optional Precision ball bearings with sealing flange High temperature