Molded Interior Door Catalog. We re door people. craftmasterdoors.com. Conmore 6 8

Transcription

1 Conmore 6 8 Molded Interior Door Catalog We re door people. craftmasterdoors.com

2 CraftMaster Molded Interior Doors Passage and Bifold Designs Made from molded high-density fiberboard, CraftMaster molded interior doors resist shrinking, swelling, cracking and joint separation. Specify the Door that Makes the Grade CraftMaster molded interior doors are routinely tested against 14 different criteria including water resistance, adhesion and overall durability to ensure consistent product quality. All doors are available primed with a low VOC primer and are ready to paint. For ease of installation, the Colonist Pre-Finished Series is available. CraftMaster molded interior doors can be specified in 1 3 /8 and 1 3 /4 thicknesses. Most 1 3 /4 thick CraftMaster molded interior doors can be manufactured to meet 20-, 45- or 60-minute fire ratings as per Intertek WH specifications. CraftMaster molded interior doors can be specified for either hollow or solid core construction and with either finger joint or MDF stiles and rails. Covered by a limited warranty. Caiman Carmelle Carrara ProCore The Quiet Door Give each room in your home the privacy it deserves with a ProCore The Quiet Door upgrade. ProCore solid core construction is available in CraftMaster molded interior doors. This solid core construction offers superior sound control and reduces the transmission of sound by up to 50 percent (compared to a hollow flush door). Plus it helps prevent the dents and dings of daily life. Tough on the Inside A CraftMaster molded door design is made from an engineered wood fiber mat that is molded under intense heat and pressure into a high-density fiberboard. The result assures consistent quality from door to door, room to room, and home to home. Cashal Classique Clermont Cremona Colonist Conmore Corvado For the full line of interior doors, visit craftmasterdoors.com. Coventry Crossmore 2

3 We re door people. Variety of Designs and Sizes Passage Sizes Bifold Sizes Caiman Smooth 6 8, 7 0 n n n n n n n n n n n n n n n * n n n n Caiman Smooth 8 0 n n n n n n n n n Carmelle Textured 6 8 n n n n n n n n n n n n n n n n n Carolina Textured 6 8 n n n n n n n n n n n n n n n n n n n n n Carrara Smooth 6 8, 7 0 n n n n n n n n n n n n n n n n n n n n n Carrara Smooth 8 0 n n n n n n n n n n n n n n n n n n n n n Cashal Smooth 6 8, 7 0 * * * * n n n n n n n n n n n * n n n n Cashal Smooth 8 0 * * * * n n n n n n n n n n n * n n n n Classique Textured 6 8 n n n n n n n n n n n n n n n n n n n n n Clermont Textured 6 8 n n n n n n n n n n n n n n n n n n n n Colonist Textured 6 8 n n n n n n n n n n n n n n n n n n n n n n Colonist Smooth 6 8 n n n n n n n n n n n n n n n n n n n n n Colonist Textured 7 0 n n n n n n n n n n n n n n n Colonist Smooth 7 0 n n n n n n n n n n n n n n n n n Colonist Textured 8 0 n n n n n n n n n n n n n n n Colonist Smooth 8 0 n n n n n n n n n n n n n n n n n n n n n Colonist Commercial Smooth 6 8, 7 0 n Colonist Pre-Finished Textured 6 8 n n n n n n n n n n n n n n n n n n n n n Conmore Smooth 6 8, 7 0 n n n n n n n n n n n * n n n n Corvado Smooth 6 8, 7 0 * * * * n n n n n n n n n n n * n n n n Corvado Smooth 8 0 * * * * n n n n n n n n n n n * n n n n Coventry Textured 6 8 n n n n n n n n n n n n n n n n n n n n n Coventry Smooth 6 8, 7 0 n n n n n n n n n n n n n n n n n n n n n Coventry Smooth 8 0 n n n n n n n n n n n n n n n n n n n n n Cremona Smooth 6 8, 7 0 * * * * n n n n n n n n n n n * n n n n Cremona Smooth 8 0 n n n n n n n n n n n n n * * * * * * * * Crossmore Smooth 6 8, 7 0 n n n n n n n n n n n * n n n n * Check with your supplier for availability. Trimming CraftMaster molded interior doors may cause damage not covered under the warranty. Colonist Carmelle Caiman Cashal Conmore Crossmore Cremona 3

4 CraftMaster Interior Doors are Green Products Build green while maintaining the beauty and functionality of molded interior doors. 3 Sustainable Materials CraftMaster molded door designs are made from wood that has no commercial timber value and is the byproduct of other operations, not old growth timber. Wood Sources for Molded Designs: Sawmill chips: generated as residual waste from sawmill operations. Field chips: residuals from field chipping operations of tree tops and leftover wood. If it is not used in manufacturing operations, it rots or is sent to landfills. The removal of this wood source allows mature trees to grow. Field chips are a byproduct of sound logging practices. All wood comes from an area within a 200 mile radius of door facings facility. 3 Certified Recycled Content CraftMaster molded door designs contain a minimum of 35% pre-consumer recycled wood fiber content. This is certified by Scientific Certification Systems under certificate number SCS-MC All hollow core CraftMaster interior passage doors contain a minimum of 25% preconsumer recycled wood fiber content. This is certified by Scientific Certification Systems under certificate number SCS-MC All hollow core CraftMaster interior bifold doors contain a minimum of 22% preconsumer recycled wood fiber content.this is certified by Scientific Certification Systems under certificate number SCS-MC Complies with CARB CraftMaster molded door designs (facings) meet Phase 2 of the California Air Resources Board (CARB) Airborne Toxic Control Measure (ATCM) No Added Urea Formaldehyde CraftMaster molded door designs have no added urea formaldehyde. This is certified by Scientific Certification Systems under certificate number SCS-MC They are manufactured with environmentally preferable phenolic resins. Through repeated testing by the Composite Panel Association (CPA), CraftMaster molded door designs have demonstrated formaldehyde emissions equivalent to background levels found in the environment. MINIMUM 35% RECYCLED CONTENT PRE-CONSUMER MINIMUM 25% RECYCLED CONTENT PRE-CONSUMER MINIMUM 22% RECYCLED CONTENT PRE-CONSUMER 3 Low VOC Primer and Adhesives CraftMaster products are primed with a low VOC primer. This primer is among the most environmentally preferable of all coatings available. 3 Contributes to Green Building Programs CraftMaster molded interior doors contribute to green building programs such as LEED and the National Green Building Standard. 4

5 We re door people. For Added Green Benefits - Specify a CraftMaster Green Door CraftMaster Green Doors have all of the green features of CraftMaster molded interior doors, plus: CraftMaster Green Doors contain no added urea formaldehyde. The adhesives used in CraftMaster Green Doors have ultra low VOC emissions Solid core CraftMaster Green Doors are made with a GreenLite Core: Sustainable solid core provides the heft, weight and sound-deadening properties of a solid wood door. Made using wood obtained from forestlands that are certified by Sustainable Forestry Initiative (SFI ). Contains pre-consumer recycled content. Produces very low formaldehyde and VOC emissions (exceeds CARB standards). How to Specify the CraftMaster Green Door Design: Any of the designs in the CraftMaster line of molded interior doors 1. Core: Standard hollow core or solid core with GreenLite fiberboard door core. Stiles and Rails: Finger joint or clear wood. Lock Block: Wood. Thickness: Either 1 3 /8 or 1 3 /4. Sizes: For available sizes, see the size chart on page 3. 1 Solid core Crossmore and Conmore doors use an MDF core and are not included in the CraftMaster Green Door specification. 5

6 Smooth Finish, Clean Designs Corvado Square top, two-panel plank door with a smooth finish. Offers the warmth and richness of a traditional plank door with a distinctive groove and modified sticking pattern for added detail. Patented and proprietary. Covered by U.S. Patent D541,947. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. Shown right: Detail of the Corvado plank panel door. Cashal Arch top, two-panel plank door that brings character and charm to any room. Combines elements of historical door design with modern functionality, making it well-suited for many home styles and décors. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. Shown right: Detail of the arch top groove panel Cashal door. Caiman Two-panel, true arch design that is the picture of elegant simplicity. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. 6

7 We re door people., Finish, clean Clean designs Designs Crossmore Patented and proprietary. Covered by U.S. Patent D616,117. Created through advanced panel technology to produce a truly authentic, molded flat panel door. Crossmore is a contemporary door that functions beautifully in renovated bungalows, sleek, modern homes and everything in between. Available in 6 8 and 7 0 passage and bifold sizes. Shown above: Detail of the Crossmore flat panel door. Conmore Patented and proprietary. Covered by U.S. Patent D616,109. The only truly authentic molded, flat five-panel door. Combines a classic panel design with a smooth-surfaced elegance Available in 6 8 and 7 0 passage and bifold sizes. 7

8 Smooth Finish, Clean Designs Cremona Bold, sleek and stylish, this door brings chic to any room. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. Coventry A classic design that has both a unique character and a universal appeal. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. Carrara Austere yet welcoming, this uncluttered design has limitless appeal. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. 8

9 We re door people. Smooth Colonist finish, Offers clean Traditional designsstyle Colonist Pine wood grain texture or smooth finish Distinguished by more than a quarter century of precision craftsmanship, this classic design rises above all imitators. Available in 6 8, 7 0 and 8 0 passage and bifold sizes. Colonist Commercial Ideal for hotels, healthcare facilities and office buildings. Fits most standard commercial hardware, including door closers, exit devices, kick plates, and card and mortise locks. Available for 3 0 openings in 6 8 and 7 0 heights. Carolina Pine wood grain texture A unique, quarter-round profile adds a stately quality to the classic six-panel design. Available in standard 6 8 passage and bifold sizes. Shown left: Detail of the Carolina quarter-round profile. 9

10 Rich Textured Designs Coventry Oak wood grain texture A classic design that has both a unique character and a universal appeal. Available in standard 6 8 passage and bifold sizes. Classique Oak wood grain texture Bold, sleek and stylish, this door brings chic to any room. Available in standard 6 8 passage and bifold sizes. Carmelle Oak wood grain texture Arched tops lend a storybook flair to this four-panel classic. Available in standard 6 8 passage and bifold sizes. Clermont Oak wood grain texture A simple, straightforward design that is versatile enough to fit in any décor. Available in standard 6 8 passage and bifold sizes. 10

11 We re door people. Colonist Pre-Finished Series Enjoy the utmost in beauty and convenience with CraftMaster Pre-Finished Series. Colonist Pre-Finished doors are available in two colors with an oak grain textured finish, as well as white with a pine wood grain textured finish. Available in standard 6 8 passage and bifold sizes. Choose from these Pre-Finished colors: CraftMaster CraftMaster CraftMaster Natural Mesa White Due to the use of a protective topcoat sealer, Pre-Finished doors cannot be repainted without fully removing the topcoat sealer. Colonist Pre-Finished CraftMaster White Colonist Pre-Finished in CraftMaster Natural Colonist Pre-Finished in CraftMaster Natural CraftMaster Reflection Series Colonist Pre-Finished in CraftMaster Mesa Colonist Pre-Finished Bifolds in CraftMaster Mesa 11

12 Handling, Installation Instructions and Finishing Recommendations Handling and Installation Instructions Note this warranty excludes all damage or failure resulting from failure to strictly follow these instructions: 1. All six sides of the door must be finished with suitable topcoat or sealer before final use. 2. Deliver door(s) to building site after plaster or cement is dry. If doors are stored at job site for more than one week, all edges should be sealed. 3. Handle with clean gloves and do not drag doors across one another or across other surfaces. 4. Store doors flat on a level surface in a dry, well ventilated building. Cover to keep clean, but allow air circulation. 5. Doors should not be subjected to excessive water, abnormal heat, extreme dryness, humid conditions or sudden changes therein. They should be conditioned to average prevailing relative humidity of the locality before hanging. 6. The utility or structural strength of the door must not be impaired in the fitting of the door, the application of hardware, or cutting and altering the door for lights, louvers, panels, or any other special details. 7. Two hinges may be used for hollow core doors weighing less than 50 pounds or 6 8 in height. Solid core doors 6 8 in height and all 7 0 doors require 3 hinges. All doors greater than 7 0 require 4 hinges. Field trimming of bifold and passage doors will void the warranty. 8. Before finishing, remove handling marks or effects of exposure to moisture through a thorough, final sanding over all surfaces of the door using a fine grit sandpaper. Clean before applying sealer or finish. Finishing Recommendations Materials Needed: Oil-based or water-based paint or stain 3-4 nylon bristle brush 1 nylon bristle brush (for staining only) 100% cotton, lint-free wiping cloth Denatured alcohol or mineral spirits How to Paint Textured CraftMaster Molded Interior Doors 1. Choose a high quality gloss or semi-gloss paint. This will offer better performance and easier application. It will also best highlight the wood grain texture on the door. 2. When buying paint, select paint to finish an interior door. Also, note the properties you most desire: low odor, excellent washability, easy clean-up and smoothness. 3. Lightly sand the entire surface with fine grit sandpaper to remove minor surface imperfections. 4. Make sure the door is clean and dry. Moisten a lintfree cloth with denatured alcohol or mineral spirits. Wipe the door thoroughly to remove all dust. Colonist 5. Paint the door edges and touch-prime any minor surface scratches. 6. When the door is fully dry, apply two coats of high-quality paint. Follow the paint manufacturer s recommendations for finishing. 7. Be sure to finish top and bottom edges. How to Paint Smooth CraftMaster Molded Interior Doors Use a paint of desired gloss level. Follow steps 1, 2, 3 and 4 noted above. Instead of step 5, apply at least three coats of topcoat with a sprayer, sanding between each coat. Of course, you re not restricted to one color. Consider contrasting the panels with the rest of the door, making the mouldings darker, or affixing decals on the panels for a child s room. Special effects, such as layering, translucence and texturing allow colors to become more complex as their effects interact with lighting. Your options are limited only by your imagination, so express yourself and turn your doors into décor. How to Stain Textured CraftMaster Molded Interior Doors Because staining CraftMaster molded interior doors by hand is more like antiquing than typical staining, it is recommended that they be stained by a professional. This is not a project for beginners. Results are dependent on the type of stain used, application technique, individual preference, experience, and humidity conditions. For those who wish to stain CraftMaster doors, the following instructions may be helpful. Always test your stain on a small section of the door first, or call to request a hand sample for test purposes. 1. Prime the door with a tan primer. This will Clermont yield better results when trying to achieve a darker, more even wood-tone finish. Purchase a water-based primer. 2. Consult your local finishing supplier for the best stain to use, based on your experience and the desired look. Typically, opaque, solid-body or pigmented solid color stains that are oil-based liquid, oil-based gel, or water-based liquid work best. Transparent or semi-transparent stains do not provide adequate color coverage and should not be used. 3. Lightly sand the entire surface with fine grit sandpaper to remove minor surface imperfections. 4. Make sure the door is clean and dry. Moisten a lint-free cloth with denatured alcohol or mineral spirits. Wipe the door thoroughly to remove all dust. 5. Follow the stain manufacturer s application instructions. Start with the door panels, then cover the horizontal rails, then cover the vertical stiles. Use the diagrams at left as a reference. Numbers 1-4 indicate the order to use when applying the stain. 6. Remove any excess stain from the corners of the panel areas by feathering with a 1 dry brush. 7. When wiping the stiles and rails, use long strokes to prevent the stain from pooling where the horizontal rails and vertical stiles meet. 8. Allow the door to dry completely for 24 hours. Follow the stain manufacturer s recommendations for a clear, protective topcoat. Note: Smooth CraftMaster molded interior doors cannot be stained. 12

13 We re door people. CRAFTMASTER INTERIOR DOOR LIMITED WARRANTy This warranty is effective for all CraftMaster Products 1 on or after June 1, 2013 for use in the United States and Canada. Any previous warranties will continue to apply to products sold under the CraftMaster name prior to this date. For additional information, including care and maintenance information refer to What This Warranty COVERS We warrant to the original owner 2 that if your CraftMaster Product exhibits a defect in material or workmanship within five (5) years of the date of original purchase, we will, at our option, repair, replace or refund the purchase price of the Product or component part. Skilled labor 3 (where deemed necessary by us) to repair or replace any component is provided for one (1) year from the date of purchase. Factory Prefinish: We warrant the factory-applied prefinish on our doors against peeling, checking, or cracking for one (1) year. Should the factory prefinish be proven defective, we will at our option, replace or refinish the door or pay a credit up to $100 per opening per opening to the current owner. (Note: this coverage applies to factory-applied finish coat options only; standard factory-applied primer is not a finish coat.) Transferability: This warranty is not transferable. How to Get Assistance If you have a problem with your CraftMaster Door, immediately upon discovery, contact the distributor or dealer from whom you purchased our product or contact us directly: Mail: CraftMaster Door Warranty Claims P.O. Box 1329 Klamath Falls, OR Phone: Fax: CustomerServiceAgents@jeld-wen.com Web: We can respond quickly and efficiently if you provide the following: a) date and location of purchase, or product identification from the tag on the top edge of the slab, b) how to contact you, c) the address where the product can be inspected, and d) a description of the apparent problem and the product (photographs are helpful). What We Will Do Upon receiving your notification, we will send out an acknowledgement within three business days to the contact, which you have provided. We will investigate your claim and will begin to take appropriate action within 30 days after receipt of notification. If your warranty claim is denied, we may charge an inspection fee for an onsite inspection that is required or requested by you. If your claim is accepted, and we choose to repair or replace the product or a component of the product, the replacement product/component will be provided in the same specification as the original product. Replacement products, components and services are warranted for the balance of the original product or service warranty, or 90 days, whichever is longer. If the claimed nonconformity is warp of a door slab, we may defer repairing or replacing the door slab for a period up to 12 months from the date of claim. It is not uncommon for a temporary warp condition to occur as the door slab adjusts to local humidity and temperature conditions. This deferral will not be counted against the warranty period. What This Warranty Does NOT Cover This warranty does not cover parts or components (e.g., locksets, handles, etc.) not sold by the manufacturer to the original owner. See your distributor or dealer regarding the warranty on the entire door system and/or these other components. We are not liable for: Normal wear and tear, including normal wear and tear of weatherstrip; and natural weathering of surfaces or variations in the color or texture of wood or finish; surface cracks that are less than 1/32" in width and/or 2" in length. Problems due to misuse or abuse; failure to follow the care and maintenance instructions; or as a result of any cause beyond our reasonable control (e.g. fire, flood, earthquake, other acts of nature, and acts of third parties outside of our control). Problems related to: improper field finishing of all surfaces (front and back) and edges (top, bottom, and sides) of the door slab and frame (See our Finishing Instructions at www. craftmaster.com); variation or unsatisfactory results in sheen or texture resulting from the field application of paint or any other finishing material. Warp for any 3'6" wide by 8' 0" high by 1 3/4", or smaller door slab, which does not exceed 1/4" in the plane of the door slab itself; door slabs wider and/or higher are not guaranteed for warp. Bow or misalignment in the frame or jamb in which the door slab is hung. Slight expansion or contraction due to varying environmental conditions; slab movement (shrinkage or swelling) of 1/4" or less due to temperature and humidity, consult our Care & Maintenance documents on how to work with this natural movement. Installation errors or flaws in building design and construction; installation must be in strict conformance with the installation instructions provided by the manufacturer of the door entry system. Structural integrity issues or other problems caused by improper field fitting of the hardware, improper sizing of the door slab, or other assembly problems. Hardware, accessories or inserts that are not provided by us. Cost for labor, removal or disposal of defective product(s), installation or finishing of the replacement door or component. Incidental or consequential damage. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so this may not apply to you. Continued on next page 13

14 CRAFTMASTER INTERIOR DOOR LIMITED WARRANTy Important Legal Information -- Please read this carefully. It affects your rights. This Limited Warranty document sets forth our maximum liability for our products. We shall not be liable for special, indirect, consequential, or incidental damages. Your sole and exclusive remedy with respect to any and all losses or damages resulting from any cause whatsoever shall be as specified above. We make no other warranty or guarantee, either express or implied, including implied warranties of merchantability and fitness for a particular purpose to the original purchaser or to any subsequent user of the Product, except as expressly contained herein. In the event state or provincial law precludes exclusion or limitation of implied warranties, the duration of any such warranties shall be no longer than, and the time and manner of presenting any claim thereon shall be the same as, that provided in the express warranty stated herein. This Limited Warranty document gives you specific legal rights, and you may have other rights that vary from state/province to state/province. Any dispute, controversy or claim arising out of or relating to this warranty, any alleged breach thereof, or the use or sale of the products to which this warranty applies shall be resolved by mandatory and binding arbitration administered by the American Arbitration Association in accordance with its commercial arbitration rules. Original purchaser agrees that they may assert claims against JELD-WEN in their individual capacity only, and not as a plaintiff or class member in any purported class action proceeding. Rejection of these dispute resolution provisions must be sent to JELD-WEN at the address provided herein within thirty (30) days of original purchaser s receipt of the Products to which this warranty applies. No distributor, dealer or representative of CraftMaster Doors has the authority to change, modify or expand this warranty. The original purchaser of this Product acknowledges that they have read this warranty, understand it and are bound by its terms and agrees to provide this warranty to the original owner of the structure into which the Product is installed. 1 CraftMaster Products shall refer to interior door products manufactured and marketed by JELD-WEN under the CraftMaster brand name for use in the United States and/or Canada. 2 This warranty extends to the original owner (original owner means the contractor/dealer/distributor/purchaser and the initial owner of the structure where the product is initially installed) and is not transferable. The original purchaser of this product acknowledges that they have read this warranty, understand it and are bound by its terms and agrees to provide this warranty to the original owner of the structure into which the product is installed. Should state or provincial law preclude no transferability, then the warranty period is effective as applicable up to five (5) years from the date of initial purchase for door slabs and systems and one (1) year from the date of manufacture for the factory pre-finish. 3 Skilled labor refers to tasks where specialized technical knowledge, experience, methods or tools are required to properly identify, diagnose and/or correct product-related problems. 2013, JELD-WEN, inc. CraftMaster is a registered trademark of CMI. All other marks are the property of their respective owners. 14

15 2013 CraftMaster Manufacturing, Inc. All rights reserved. All trademarks and service marks (registered and unregistered) shown are owned by or licensed to CraftMaster Manufacturing, Inc. or its affiliates /13 We re door people. 15

16 We re door people. CONTACT US craftmasterdoors.com craftmasterdoors.com