Architectural Door Accessories

Transcription

1 Architectural Door Accessories McKinney Products Canadian Book s are effective September 0, 208

2 s are effective September 0, 208 McKInney General Information Table of Contents General Information... GEN- GEN-8 Terms & Conditions... GEN-3 GEN-4 es... GEN-5 Options... GEN-6 GEN-7 Index... GEN-8 Full Mortise Hinges... FM- FM-2 MacPro Hinges... FM-20, FM-2 Electric Hinges... EH- EH-3 MacPro Electric Hinges... EH-7 Full Mortise Anchor Hinge Sets... AH- AH-4 Reinforcing Pivots... AH-4 Half Mortise Hinges... HM- HM-3 Half Surface Hinges and Back Plates... HS- HS-2 Full Surface Hinges... FS- Spring Hinges & Pivots... SH- SH-4 MacPro Hinges... SH-2 Rescue Hardware... RH- Specialty Hinges & Residential... SP- StormPro Hinges... SP- Designer Hardware - Deco Tips... DH- DH-4 Aluminum Continuous Geared Hinges... CG- CG-5 Steel & Stainless Pin and Barrel Continuous Hinges... CH- CH-9 Power Transfer Locator Templates... CH-0 Screw Packs... SPK- SPK-2 Check our websites for Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

3 s are effective September 0, 208 ACCEPTANCE: ASSA ABLOY Door Security Solutions Canada, a division of ASSA ABLOY Canada Ltd. and all of its current and future associated companies, subsidiaries and operating brands reserve the right to decline an order, in whole or in part, when the type or quantity of goods or credit worthiness of the Purchaser is not satisfactory to us in our sole and absolute discretion. The terms and conditions contained herein constitute the entire agreement between the parties. Purchase Orders, Quotations ( Quote ) requests, Acknowledgements or the like issued by the Purchaser that have contrary standard terms and conditions are not binding on ASSA ABLOY Door Security Solutions Canada, unless such terms and conditions are approved in a separate written agreement by ASSA ABLOY Door Security Solutions Canada s authorized representatives. In the event of an acceptance of Purchaser s Purchase Order by ASSA ABLOY Door Security Solutions Canada, the Purchaser agrees that such acceptance is solely conditioned on Purchaser s acceptance of the terms and conditions set forth in this instrument, regardless of the terms and conditions specified in the Purchaser s Purchase order. The terms and conditions in Purchaser s Purchase Order which conflict with terms and conditions of this instrument shall be disregarded and are hereby rejected, and this instrument shall constitute the entire agreement between ASSA ABLOY Door Security Solutions Canada and the Purchaser. In the event that ASSA ABLOY Door Security Solutions Canada does not enforce or require strict performance of any term or condition hereof, or of any other document, instrument or other agreement relating to goods sold, such lack of enforcement or requirement of strict performance will not waive, affect or diminish any right of ASSA ABLOY Door Security Solutions Canada to enforce or require strict performance of such term or condition in the future. PRICES: All prices are subject to change without notice and are not guaranteed. All shipments will be made at prices in effect at the time of order acceptance. Possession of this price list does not constitute an agreement to sell. Acknowledgements, invoices and quotations are on an Errors and Omissions Excepted basis (commonly referred to as E.O.E.). We reserve the right to correct clerical, stenographic and other obvious errors at any time. AGREED PAYMENTS AND TERMS: % tenth of the following month, Net 30th of the following month. It is understood that ASSA ABLOY Door Security Solutions Canada may impose and charge a finance charge of 2% per month or the highest rate allowed by law on any amount which becomes past due and delinquent. Additionally, the Customer shall be responsible for all collection costs, court costs and reasonable attorney s fees in connection with the recovery of any delinquent amount. MINIMUM INVOICE: Minimum invoice for complete product is $ net product value. The minimum invoice for parts orders is $00.00 net product value. Any orders not totaling these minimums will be invoiced at the minimums. This policy does not include the following: Cut (bitted) Keys of any type, Master Keyed Cylinders, Master Keyed Padlocks and Factory Generated Bitting Lists. Same day order expedites will be invoiced at book less 50%. QUOTATIONS: If ASSA ABLOY Door Security Solutions Canada elects to offer a quote, such quote will be valid until the expiration date on that quote. Complete shipment of the order must be accepted by Purchaser within standard lead times. The QUOTE number must be referenced on the order. Any invoiced order that has the incorrect discount applied to it and did not have the QUOTE number written on the order will have a service fee of $00.00 net DEDUCTED from any sales credit issued for the difference in discount. The quote is null and void if the Purchase Order does not include ALL product lines listed on the Quote or if the quantities for an item covered by the Quote deviate by 0% or more. The Purchaser will have to solicit a new quotation. With the issuance and acceptance of a QUOTE for the purchase of products, the Purchaser agrees that products so purchased will not be resold or transferred to any Distributor not authorized by ASSA ABLOY Door Security Solutions Canada to sell its products. This would be inclusive of branches of the quoted Distributor. Failure to abide by this restriction may result in the Distributor s ineligibility for Quotes, or other actions in ASSA ABLOY Door Security Solutions Canada s discretion. ASSA ABLOY Door Security Solutions Canada and its sales representatives reserve the right, in their sole discretion and for any reason, to refuse a Distributor s request to quote a price other than ASSA ABLOY Door Security Solutions Canada s standard list price and regardless of whether ASSA ABLOY Door Security Solutions Canada or its sales representatives have previously quoted discounted prices to the Distributor on some or all of its orders. SPECIAL ORDERS: Products not catalogued or listed in this price book will be considered as special products, and will not be manufactured without prior approval from ASSA ABLOY Door Security Solutions Canada. A minimum special handling charge of $50.00 will be added for non catalogued product. Any additional labour or material required will be charged accordingly. Special products require special handling, and therefore standard lead times may not apply. Please consult with your Sales Representative for further details. HIGH SECURITY ORDERS: To ensure proper control of End User restricted Products, ASSA ABLOY Door Security Solutions Canada requires that the End User complete a Delivery of Controlled component form indicating to whom the product will be shipped to upon leaving the factory or the distribution centre. All orders must be accompanied with a current copy of the Authorization form and must be signed by the proper authorized personnel whose name(s) is on file with ASSA ABLOY Door Security Solutions Canada. High Security products are defined as high security key blanks, cut keys, sidebars, sub assemblies, complete and master-keyed cylinders, and key charts. ASSA ABLOY Door Security Solutions Canada reserves the right to request authorization from the end user if necessary before the order is processed. McKinney General Information Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in GEN-

4 s are effective September 0, 208 McKInney General Information CHANGES / CANCELLATION OF ORDERS: Changes or cancellations to a non stock order that has been confirmed will be subject to a charge of costs for material and labour expenses that have been incurred prior to notification from Customer. Handling charges are billed on Customer s original order. All change requests for stock goods must be submitted in writing to Customer Service within two (2) business days of receipt of confirmation of the order. In those instances where a cancellation is accepted, ASSA ABLOY Door Security Solutions Canada reserves the right to make a reasonable cancellation charge based on expenses incurred. PACKAGING: Many items are defined as to Lot Packaging or Minimum Order. The case lot policy does not apply to hardware to be used on a specific hardware project. DELIVERY: Orders will be acknowledged and given a scheduled delivery date based on estimated manufacturing lead times. Complete information is required to process all orders. Orders with insufficient information for processing (i.e. keying information, door sizes, etc.) may be subject to extended lead times which are relative to the time required in obtaining the necessary information for order processing. Manufacturing lead time will begin once all information is received to process an order. ASSA ABLOY Door Security Solutions Canada will use reasonable efforts to deliver products as estimated, but makes no guarantee as to delivery dates. ASSA ABLOY Door Security Solutions Canada will not be liable for back charges incurred based on availability of product or as a result of delays in delivery caused by insufficient information required to process an order. ASSA ABLOY Door Security Solutions Canada will not be held responsible for delays in delivery caused by strikes, fires, floods or any other causes beyond our control, including the delivery of material to us. Under no circumstances shall ASSA ABLOY Door Security Solutions Canada be liable or accountable for consequential damages due to failure of delivery. Unless your order specifies otherwise, partial shipments will be made on or after the scheduled delivery date. TERMS OF SHIPMENT: All products are shipped FOB the factory or the distribution centre unless otherwise agreed to in writing from ASSA ABLOY Door Security Solutions Canada. Title to and risk of loss product shipped is the responsibility of the purchaser and delivery is deemed to be complete upon transfer of the product to a common carrier. Carriers carry limited insurance. If the customer requires additional insurance coverage please contact our customer service department. All claims for shortages and damage are the responsibility of the purchaser. ASSA ABLOY Door Security Solutions Canada will assist the Purchaser with documentation necessary to make a claim if requested to do so by the purchaser. ASSA ABLOY Door Security Solutions Canada will ship via the best possible carrier. Shipments at the customer s request will be prepaid and any up-charge (actual cost less the amount negotiated by ASSA ABLOY Door Security Solutions Canada) will be added to the invoice. CLAIMS: In the event of ASSA ABLOY Door Security Solutions Canada or Customer error, claims for shortages, pricing errors and/or incorrectly filled orders must be submitted in writing to Customer Service within thirty (30) days from receipt of material. Any claims for shortages or damage by the Carrier must be made by the Customer directly to the Carrier. Limited Carrier insurance is typically offered for all orders. If the Customer requires additional insurance, please contact an ASSA ABLOY Door Security Solutions Canada Customer Service Representative upon submittal of the order. ASSA ABLOY Door Security Solutions Canada will obtain requested insurance and the additional cost will be included on Customer s invoice. INVOICE DEDUCTION: An ASSA ABLOY Door Security Solutions Canada Sales Representative or Customer Service Representative must be notified of any disputed invoices within thirty (30) days from the date of invoice. Deductions should only be taken for the disputed amount and the balance of the invoice is due and payable within standard payment terms. RETURNED GOODS: No Material is to be returned to our facilities without prior written approval from customer service. It is the policy of ASSA ABLOY Door Security Solutions Canada to not accept returns of any materials that are correctly furnished as per the Distributor s Purchase Order. Mercury and Turbo material may be returned with approval, if ASSA ABLOY Door Security Solutions Canada believes the product is resalable. All such product must be returned in its original unmarked carton. The goods must have been shipped and invoiced in the previous sixty (60) days. Returns will be at the distributor s expense. The goods returned will be subject to inspection and a minimum 20% restocking fee will be applied to compensate for the cost of inspection, repacking and handling. Return of product due to customer order error or accommodation must be prearranged with ASSA ABLOY Door Security Solutions Canada and approved in writing by Sales Management. A minimal restocking fee of 50% will be charged. Upon receipt and verification by ASSA ABLOY Door Security Solutions Canada that the returned merchandise is in saleable condition and that the material can be returned to the original manufacturer. Defective goods that are out of warranty period will not be accepted for return. Products that are master-keyed, special orders, key bitted will not be accepted under any circumstances, unless the product is determined to be defective. PROCEDURE: Ensure the RGA labels that are sent to Purchaser by ASSA ABLOY Door Security Solutions Canada are visible on return goods shipment. Ensure that the RGA number appears on the return shipment label and is legible. Return the authorized merchandise within sixty (60) days from the date of RGA issuance. Return shipments must be freight prepaid to the distribution centre (at time some directions may apply to return the goods to the original manufacturer) ASSA ABLOY Door Security Solutions Canada is not liable Check our websites for Canada: GEN-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

5 s are effective September 0, 208 for damages to product during shipping. No credit may be taken or issued prior to RGA approval and receipt of product. All defective goods within the terms of our limited warranty may be returned for repair or replacement only. TAXES: s do not include any present or future Federal, Province, or Local property, license, privilege, sales, use, excise, gross receipts or other like taxes or assessments, which may result from transactions or any services performed in connection herewith. GOVERNING LAW: The rights and obligations of the parties shall be governed by the laws of the Province of Ontario, excluding any conflicts of law provisions. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement. INDEMNITY: Purchaser shall indemnify ASSA ABLOY Door Security Solutions Canada and hold ASSA ABLOY Door Security Solutions Canada harmless against all claims, liability, loss or other damages (including costs, legal or otherwise incurred by ASSA ABLOY Door Security Solutions Canada) to all persons for injury of any nature, including sickness and/or death, property damage at the time of delivery or after when the product is no longer in ASSA ABLOY Door Security Solutions Canada possession or control. FORCE MAJEUR: ASSA ABLOY Door Security Solutions Canada shall not be liable for its failure to perform due to any contingencies beyond its control, including but not limited to acts of God, fires floods, wars, sabotage, accidents, labour disputes, shortages, government laws, ordinances, rules and regulations. ASSA ABLOY Door Security Solutions Canada shall not be liable for its failure to deliver due to its inability to obtain materials, equipment failure, labour actions, transportation issues or any similar contingencies. In the event of delays due to the aforementioned contingencies, the date of delivery will be postponed by such length of time as the circumstances dictate. COPYRIGHTS AND PATENTS: All products in ASSA ABLOY Door Security Solutions Canada catalogues, brochures and price lists are either patented, Copyrighted or registered by ASSA ABLOY Door Security Solutions Canada. PARTNER SERVICES IN CANADA For Terms & Conditions and Warranty information pertaining to product sales in Canada, please visit: Business Hours: Customer Service Hours: 8:00 AM to 4:30 PM Eastern Standard Time. Toll Free Telephone : Order Fax : Order orders.dss.ca@assaabloy.ca RGA rga.dss.ca@assaabloy.com Technical Support techsupport.dss.ca@assaabloy.com Customer Support: Ontario customerservice.dss.caontario@ assaabloy.com Customer Support: East Customer Support: West McKinney General Information Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in GEN-3

6 s are effective September 0, 208 McKInney General Information McKinney and B.H.M.A. Symbols BHMA Code Base Material Ferrous (Steel) Non-Ferrous (Brass or Stainless) McKinney FINISH 600 P A B A A D D Check our websites for Canada: GEN-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

7 s are effective September 0, 208 McKinney and Government Symbols U.S. Description McKinney U.S.P. Prime Powder Coat for Painting P Listed U.S. 3 Bright Brass 3 Listed U.S. 4 Dull Brass 4 Listed U.S. 5 Dull Brass, Oxidized 5* 30% over 0B U.S. 7 Brass, Nickel Oxidized, Bright Relieved 7* 30% over 0B U.S. 9 Bright Bronze 9 30% over 0B U.S. 0 Dull Bronze 0 Listed U.S. 0A Antique Bronze, Oiled and Lacquered 0A Listed U.S. 0B Antique Bronze, Oiled 0B Listed U.S. Dull Bronze, Oxidized * 30% over 0B U.S. 4 Bright Nickel Plated 4 Same as 26 U.S. 5 Dull Nickel Plated 5 Same as 26D U.S. 5A Nickel Oxidized Relieved 5A* P.O.A. U.S. 20 Statuary Bronze, Light 20* 30% over 0B U.S. 20A Statuary Bronze, Dark 20A* 30% over 0B U.S. 26 Bright Chromium 26 Listed U.S. 26D Dull Chromium 26D Listed U.S. 32 Polished Stainless Steel 32 Listed U.S. 32D Dull Stainless Steel 32D Listed McKinney General Information * Check with the factory for availability and pricing on these finishes McKinney Powder Coat es May not be available on MacPro or Double Acting Spring Hinges MicroShield Agion Antimicrobial 32DBIO Add $24.70 to price of 32D Aluminum AP Listed Dark Bronze Powder Coat D3 Same as AP Black Powder Coat D4 Same as AP Dark Oxidized Satin Bronze 0BE 5% Less than 0B Black Suede Powder Coat BSP 5% Less Than 0B CPC or 0B over Stainless add 0% to 32D price. Every effort is made to furnish finishes which do comply with the Standard, however we cannot guarantee that our finish will match other manufacturers finish. Where a special finish or a matched finish is required, a sample must be submitted with the order. * P.O.A. on Application Consult the factory for pricing and availability on these custom finishes. 722 or EB 30% over 0B for clear coats Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in GEN-5

8 s are effective September 0, 208 McKInney General Information Options/Additions Where Not Listed No Logo Hinges supplied less ASSA ABLOY logo (not available on LISTED Hinges) - New lead times will apply and factory may need to adjust lead times after lead times of order is originally acknowledged. Blank Hinges (No Screw Holes) Blank hinges regularly furnished without swaging (flat back) unless otherwise specified. Bulk Package, Suffix BP Consult factory for availability Special Swaging Special Swaging Add 30% to price Add 30% to price No additional charge Add 30% to price Add $7.35 to electrical option add for all Swing Clear Hinges CC Option- Concealed Circuit Brass, Steel or Stainless Steel Base Add 4 wires - suffix CC4 $ wires - suffix CC6 $ wires - suffix CC8 $ wires - suffix CC0 $ wires - suffix CC2 $77.08 Extra Long Leads (over 2") for CC4 $0.20 per foot Extra Long Leads (over 2") for CC6 $4.72 per foot Extra Long Leads (over 2") for CC8 $9.6 per foot Extra Long Leads (over 2") for CC0 $24.72 per foot Extra Long Leads (over 2") for CC2 $29.36 per foot CC Option- Concealed Circuit with 2 8-Gauge Wires Brass, Steel or Stainless Steel Base Add 4' Lead Add 2 wires - suffix CC2-8 $ $ wires - suffix CC4-8 $ $ wires - suffix CC6-8 $ $ wires - suffix CC8-8 $66.36 $ wires - suffix CC0-8 $ $59.2 * Hinges are provided with two 8-gauge wires, additional wires will remain standard 28-guage QC Option- Electrolynx Quick Connect Concealed Circuit Brass, Steel or Stainless Steel Base Add 2 wires - suffix Qc2 $ wires - suffix QC4 $ wires - suffix QC6 $ wires - suffix QC8 $ wires - suffix QC0 $ wires - suffix QC2 $ Extra 6" Pigtail for QC Butt Hinge Add 0977 QC2 Pigtail $ QC4 Pigtail $ QC8 Pigtail $20.08 MG 6 Mortar Guard ( #63333) $4.92 each Check our websites for Canada: GEN-6 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

9 s are effective September 0, 208 Options/Additions Where Not Listed PoE Option - Power over Ethernet Available on 4 2" and 5" height hinges only Add Brass or Steel Base $, MM Option - Magnetic Monitoring Add Magnetic Monitoring - suffix MM $ Extra Heavy Magnetic Monitoring - suffix EHM $47.74 MM Magnet Assembly Only $72.82 EHM Magnet Assembly Only $75.08 MM Magnet Assembly & Switch $27.52 EHM Magnet Assembly & Switch $39.98 McKinney General Information Non Removable Door Suffix NRD Moderne Hinge only (2 Knuckle) One NRD provided per set of 3 hinges Non Removable Pins Set screw in barrel suffix (NRP SET SCS ONLY $.50 EA NO DISC) Raised Barrel Full Mortise Hinges Bearing Hinges Only Raised barrel prefix RB 4 2" x 4 2" Standard and Heavy Weight. 5" x 4 2" Heavy Weight Only. Hinges are NRP and reversible for handing Round Corner Prefix RC Add $8.34 per door Add $.2 each Add $59.26 each 5 32", 4" or 5 8" Round corner full mortise only Add $7.78 each Round corner hinges (RC) will be furnished in 4" radius unless otherwise specified Beveled Hinges (where doors are beveled on hinge side specify as follows) For 3 knuckle hinges use 5000 series. Example TA793 or TA792 will become TA5793 or TA5792 For 5 knuckle hinges use a 4000 series. Example TA274 or T4A3386 will become a TA474 or T4A4386 TA273 will become A TA473, A TA3350 becomes a TA4350, TA3750 becomes TA4750 If a part # is not shown in price book for Beveled Edge Hinge, add 0% to the price of Square Edge Hinge Add $33.26 each Add $39.46 each Add $67.46 each Safety Stud Featured Suffix SSF Prison Safety Feature Suffix PSF (available HTA386 (32D) part # 8534 only) Slip in Hinges Suffix SIH Type I (Handed), SIH Type II Regular weight bearing hinge only (Indicate hand when ordering) Special Screws ( 2" x 2-24 machine" - 4" x 2 wood) Consult factory for price and minimum requirements on additional sizes Steel Spanner Head $2.48 each Brass Spanner Head $3.40 each Stainless Steel Spanner Head $6.28 each Spanner bit holder tool $93.74 each Spanner bit (for use in holder) $63.76 each TORX Pin head security screws - Suffix TXS, machine screws provided. Wood screws by request only Steel Torx $3.92 each net add per hinge or $0.96 each Stainless Torx $5.96 each net add per hinge or $.52 each TORX bit* $65.20 each TORX bit holder tool* $93.62 each *#20-2" x 2-24 & 4" x 2 wood screw *#25-2" x 4"-20 machine screw, 2" x 2 wood screw TIPS -- Hospital Tips Prefix H Regular weight plain bearing, oil impregnated or ball* Heavy weight oil impregnated or ball* Solid Brass Ball Tips suffix x BT up to 6" in height* Solid Brass Steeple Tips suffix x ST up to 6" in height* Deco Tips for two and three knuckle hinges, where not listed, suffix RT, FT, GT, LT Architectural Hardware Presentation Folder FS Perforated cardboard shims # 7588 * Ball Tips or Steeple Tips or Deco Tips are not available on Swing Clear Hinges Add $36.26 each Add $36.26 each Add $36.26 each Add $36.26 each Add $36.26 each $6.20 net $.20 each Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in GEN-7

10 s are effective September 0, 208 McKInney General Information Index 45 SH SH SH AH AH AH AH-4 00 SH SP-2 44 SP SP-2 502, 502R SH-, SP SH- 552 SH- 300 SH MRB SH RB SH SH SH SH-3 BP-0 HS-2 BP- HS-2 BP-2 HS-2 CSS-9 RH- DLS-8 RH- DS-6 RH- Deco Hinges DH- DH Series DH- DH-5 EP-5J RH- H8007 SH-4 HS00 SH-3 HTA386 FM-2 HTA74 FM-4 HTA786 FM-4 HTA274 FM-0 HTB386 FM-2 HTB786 FM-5 J300 SH-3 K-MCK-2HD CG-4 MCK-2HD CG-3 MCK-4HD CG-3 MCK-22HD CG-3 MCK-25HD CG-3 MCK-28HD CG-3 MCK-54HD CG-4 MCK-58HD CG-4 MCK-WTHD CG-3 MCK-FM300 CH-6 MCK-FM327 CH-7 MCK-FM3500 CH-8 MCK-FS30 CH-7 MCK-FS302 CH-8 MCK-FS309 CH-8 MCK-FS32 CH-8 MCK-FS350 CH-8 MCK-FS3502 CH-9 MCK-FM3700 CH-9 MCK-FS370 CH-9 MCK-FS3702 CH-9 MCK-HG305 MCK-HG306 MCK-HG30 MCK-HG3 MCK-HG35 MCK-HG322 MCK-HG323 MCK-HG326 MCK-HG3505 MCK-HM304 MCK-HS303 MCK-HS3703 MG-6 MK0379 MP79 MPB79 MPS60 MPB68 MPB9 MPB99 MPS679 PH-4 SP3786 SP3386 SQ333 T234 T274 T2895 TA34 TA386 TA39 TA392 TA393 TA394 TA74 TA786 TA79 TA792 TA793 TA794 TA795 TA234 TA2372 TA2395 TA2398 TA274 TA273 TA277 TA2772 TA2774 TA2798 TA2895 TA333 TA3350 TA3374 TA3383 TA3750 TA4395 TA4895 CH-6 CH-7 CH-8 CH-7 CH-6 CH-6 CH-6 CH-6 CH-9 CH-7 CH-7 CH-9 GEN-4 SH-2 FM-20 FM-2 SH-2 FM-2 FM-2 FM-2 SH-2 SP- SP- SP- DH-5 FM-5 FM-7 FM-8 SP-2 FM- FM-2 AH- AH- AH- AH- FM-3 FM-4 AH-2 AH-3 AH-3 AH-3 FM-4 FM-5 FM-6 HS- FM-7 FM-7 FM-8 FM-9 FM-0 FM-2 FS- HS-2 HM-2 FM-2 FM-3 FM-3 FM-4 FM-4 HM-2 DH-5 FM-7 FM-5 FM-3 TA5392 TA5393 TA5394 TA5792 TA5793 TA5794 TA234BT TA234ST TCA234 TCA274 TCA3386 TCA3786 T4A338 T4A3382 T4A3384 T4A3386 T4A3395 T4A378 T4A3782 T4A3784 T4A3786 T4A3795 T4A3796 T4A3789 T4A4795 T4B3386 T6A3786 T6B3386 AH-2 AH-2 AH-3 AH-3 AH-4 AH-4 FM-7 FM-7 FM-6 FM-9 FM-0 FM-6 FM-9 FS- HS- HM-3 FM-6 FM-7 FS- HS-2 HM-3 FM-8 FM-9 FM-20 HS- HM-3 FM-20 FM-5 FM-9 FM-5 Check our websites for Canada: GEN-8 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

11 s are effective September 0, 208 Standard Weight Three Knuckle Non-Ferrous Bearings TA34 Code " x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm NRP 6933 P AP A B D D P AP A B D D P AP A B D D D-NRP P AP A B D D NRP D-NRP D-NRP " x 4" 27 mm x 0.60 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm P AP A B D D P AP A B D D P AP A B D D Std. 3 Knuckle Hospital Tip Non-Ferrous Bearings TA34 Code " x 4" 4.30 mm x 0.60 mm D " x 4 2" 4.30 mm x 4.30 mm D McKinney Full Mortise Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-

12 s are effective September 0, 208 McKinney Full Mortise Hinges Heavy Weight Three Knuckle TA386 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm (NRP) D-NRP D P AP A B D D D-NRP D-NRP P AP A B D D D-NRP D-NRP " x 5" 27 mm x 27 mm 6" x 6" 52.4 mm x 52.4 mm P AP A B D D P AP A B D D TA386 Code " x 6" 4.30 mm x mm 32D Hospital Tip Heavy Weight Three Knuckle Non-Ferrous Bearings Stainless Steel Institutional Hinges HTA386 Code " x 4 2" 4.30 mm x 4.30 mm HTA386 x PSF Code 30 Packed with 2 " x 2-24 Torx Pin Head Security Machine Screw D D HTB386 MSP Set Code 30 Option A includes three hinges with hospital tips. Top and bottom hinges supplied with PSF and SSF, middle hinge is not $ set Option B - QC8 includes three hinges with hospital tips. Top and bottom hinges supplied with PSF and SSF, middle hinge is provided with QC and no PSF of SSF. Code 39 $, QC8 $, QC2 Canada: FM-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

13 s are effective September 0, 208 Steel Standard Weight Three Knuckle Bearing TA74 Code " x 4" P mm x 0.60 mm AP A B D " x 3 2" D mm x mm 6922 D " x 4" 0.60 mm x 0.60 mm Hospital Tip 6978 P AP A B D P AP A B D 35.8 Steel Standard Weight Three Knuckle Bearing TA74 Code 30 5" x 4" 27 mm x 0.60 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) HTA74 Code " x 4 2" 4.30 mm x 4.30 mm D P AP A B D P AP A B D P AP A B D D D P-NRP D-NRP NRP NRP B-NRP D-NRP D Steel Standard Weight Three Knuckle Bearing Wide Throw TA74 Code " x 6" 4.30 mm x 52.4 mm P AP B D D D Same s for up to 4 2" x 8" McKinney Full Mortise Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-3

14 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Heavy Weight Three Knuckle Bearing TA786 Code 30 Steel Heavy Weight Three Knuckle Hospital Tip HTA786 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2"-NRP 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm 6" x 6"* mm x mm D D-NRP P AP A B D P-NRP B-NRP D-NRP P AP A B D P AP A B D P AP A B D * For 6" x 4½" or 6" x 5" use price of 6" x 6" " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm Hinges are packed with 2" x 2-24 Torx Pin Head Machine Screws. Steel Swing Clear Heavy Weight 3 Knuckle Bearing Reversible TA795 Code " 4.30 mm 5" 27 mm P D D x PSF P AP A B D P AP A B D D For swing clear heavy weight three knuckle bearing, beveled edge application orderta5795. (Hinges are reversible and non-handed.) Hospital Tip Bearings HTA795 Code " 4.30 mm D "27 mm D Canada: FM-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

15 s are effective September 0, 208 Non-Ferrous Standard Weight 5 Knuckle T234 Code " x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm P A B D D P A B D D P A B D " x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2"-NRP 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm Non-Ferrous Standard Weight 5 Knuckle Bearing TA234 Code " x 3 2" mm x mm 6020 P A B D D " x 4" 0.60 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm P A B D D B-NRP D-NRP D-NRP P A B D D P A B D D P A B D D P A B D D Continued on next page McKinney Full Mortise Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-5

16 s are effective September 0, 208 McKinney Full Mortise Hinges Non-Ferrous Standard Weight 5 Knuckle Bearing Continued TA234 Code " x 4"-NRP 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 5" x 4" 27 mm x 0.60 mm D-NRP D-NRP B-NRP P A C CPC (SS) B S 0B (SS) E 0BE (SS) D D P-NRP NRP NRP B-NRP D-NRP D-NRP P A B Continued on next column 5" x 4" 27 mm x 0.60 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 4 2"-NRP 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm 6" x 6" mm x mm D D P A B D D D-NRP D-NRP B-NRP P A B D D P A B D D Non-Ferrous Standard Weight 5 Knuckle Concealed Bearing TCA234 Code " x 4 2" 4.30 mm x 4.30 mm P A B D D " x 5" 27 mm x 27 mm P A B D D Canada: FM-6 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

17 s are effective September 0, 208 Non-Ferrous Standard Weight 5 Knuckle Concealed Bearing Non-Ferrous Standard Weight Five Knuckle Ball Tip TA234BT Code 50 Non-Ferrous Swing Clear Standard Weight TA2395 Code 50 McKinney Full Mortise Hinges 4 2" x 4 2" 4.30 mm x 4.30 mm " 4.30 mm D " D mm TA D Hinges are NRP and Reversible. Non-Ferrous Standard Weight Five Knuckle Steeple Tip TA234ST Code " x 4 2" 4.30 mm x 4.30 mm Steel Standard Weight 5 Knuckle T274 Code " x 3 2" mm x mm 3 2" x 3 2" mm x mm (RHP) 5535 P AP A B RC-0B E 0BE D B-BT RC-26D D RC-D Reverse Hole Pattern 26D D D Non-Ferrous Standard Weight Five Knuckle Wide Throw TA2398 Code " x 6" 4.30 mm x mm 4 2" x 8" 4.30 mm x mm 5" x 8" 27 mm x mm 4" x 4" 0.60 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm (NRP) D D P AP D A RC-26D B D RC-0B P AP A B D D D P-NRP D-NRP Continued on next page Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-7

18 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Standard Weight 5 Knuckle Continued T274 Code " x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) P AP A B E 0BE D D D P-NRP AP-NRP NRP NRP NRP B-NRP NRP D-NRP " x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm P AP A B D D D P AP A B D D D Hinge Pin Stop Code 57 For 4 2" T274 & TA274 No. Description Hinge Pin Stop 26D Steel Standard Weight 5 Knuckle Bearing TA274 Code " x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm P AP A B D P AP A B D " x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm (NRP) P AP A B E 0BE D D D RC-26D* P-NRP D-NRP A-NRP B-NRP RC-26DNRP* RC-D4-NRP* *Round Corner Continued on next page Canada: FM-8 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

19 s are effective September 0, 208 Steel Standard Weight 5 Knuckle Bearing Continued TA274 Code " x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) 5" x 4" 27 mm x 0.60 mm Steel Standard Weight 5 Knuckle Concealed Bearing TCA274 Code P AP A B E 0BE D D D P-NRP AP-NRP NRP NRP NRP NRP A-NRP B-NRP E 0BE-NRP NRP D-NRP D3-NRP D4-NRP P AP D " x 4 2" 27 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm (NRP) 5" x 5" 27 mm x 27 mm 6" x 6" 52.4 mm x 52.4 mm 5600 P AP A B D P-NRP D-NRP P P-NRP AP A B D P AP A B D McKinney Full Mortise Hinges 4 2" x 4" 4.30 mm x 0.60 mm P AP A B D D D " x 4 2" 4.30 mm x 4.30 mm P AP A B D D D Continued on next page Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-9

20 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Standard Weight 5 Knuckle Concealed Bearing Continued TCA274 Code 50 5" x 4 2" 27 mm x 4.30 mm Steel Standard Weight 5 Knuckle Hospital Tip Bearing HTA274 Code P AP A B D D D " x 4" 4.30 mm x 0.60 mm D " x 4 2" 4.30 mm x 4.30 mm 5582 P D " x 4 2" 27 mm x 4.30 mm " x 5" 27 mm x 27 mm P AP A B D D D Steel Standard Weight 5 Knuckle Bearing Safety Stud HTA274 Code " x 4" 4.30 mm x 0.60 mm NRP D NRP Steel Standard Weight 2 Knuckle Bearing TA273 Code " x 3 2" mm x mm R.H P L.H P R.H AP L.H AP R.H L.H R.H L.H R.H " x 3 2" mm x mm L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D Continued on next page Canada: FM-0 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

21 s are effective September 0, 208 Steel Standard Weight 2 Knuckle Bearing Continued TA273 Code 20 4" x 4" 0.60 mm x 0.60 mm R.H P L.H P R.H AP 9.92 L.H AP 9.92 R.H L.H R.H L.H R.H L.H R.H A 9.92 L.H A 9.92 R.H B L.H B R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D " x 4" 4.30 mm x 0.60 mm R.H P L.H P R.H AP 75.0 L.H AP 75.0 R.H L.H R.H L.H R.H L.H R.H A 75.0 L.H A 75.0 R.H B 86.2 L.H B 86.2 R.H L.H R.H D 60.8 L.H D 60.8 R.H D L.H D R.H D L.H D " x 4 2" 4.30 mm x 4.30 mm R.H P L.H P R.H. 656 AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B 9.20 L.H B 9.20 R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D " x 4" 27 mm x 0.60 mm R.H P.24 L.H P.24 R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D Continued on next page McKinney Full Mortise Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-

22 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Standard Weight 2 Knuckle Bearing Continued TA273 Code 20 5" x 4 2" 27 mm x 4.30 mm R.H P 2.32 L.H P 2.32 R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D " x 5" mm x 27 mm 3 2" x 6" mm x 52.4 mm " x 5" 27 mm x 27 mm R.H P L.H P R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B 92.0 L.H B 92.0 R.H L.H R.H D L.H D R.H D L.H D R.H D L.H D " x 6" 0.60 mm x 52.4 mm 4" x 7" 0.60 mm x 77.8 mm 4 2" x 6" 4.30 mm x 52.4 mm Steel Standard Weight Wide Throw 5 Knuckle Bearing TA2798 Code P AP A B D P AP A B D P AP A B D P AP A B D P AP A B D Continued on next page Canada: FM-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

23 s are effective September 0, 208 Steel Standard Weight Wide Throw 5 Knuckle Bearing Continued TA2798 Code " x 7" 0.60 mm x 77.8 mm 4 2" x 8" 4.30 mm x mm 5900 P AP A B D P AP A B D " x 7" 27 mm x 77.8 mm 5" x 8" 27 mm x mm 5957 P AP A B D P AP A B D McKinney Full Mortise Hinges Steel Standard Weight Swing Clear 5 Knuckle Bearing TA2895 Code 50 Steel Standard Weight Swing Clear 5 Knuckle Bearing For Beveled Edge Doors TA4895 Code " 4.30 mm 5" 27 mm P AP A B D D " 4.30 mm Hinges are NRP, reversible and non-handed. 5" 27 mm P AP A B D D Custom Hinges to fit REDIFRAME Code 50 No. Description 57006SP SPL 4 /2 TA D REDIFRAME SP SPL 4 /2 TA D REDIFRAME Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-3

24 s are effective September 0, 208 McKinney Full Mortise Hinges Non-Ferrous Standard Weight 2 Knuckle Bearing TA333 Code " x 3 2" mm x mm R.H D 7.36 L.H D " x 4" 0.60 mm x 0.60 mm R.H D L.H D " x 4" 4.30 mm x 0.60 mm R.H D L.H D " x 4 2" 4.30 mm x 4.30 mm R.H D L.H D " x 4" 27 mm x 0.60 mm R.H D L.H D " x 4 2" 27 mm x 4.30 mm R.H D L.H D " x 5" 27 mm x 27 mm R.H D L.H D Non-Ferrous Heavy Weight 2 Knuckle Bearing TA3350 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 5" 27 mm x 27 mm R.H D L.H D " x 4 2" 27 mm x 4.30 mm R.H D L.H D R.H D L.H D Canada: FM-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

25 s are effective September 0, 208 Non-Ferrous Heavy Weight 5 Knuckle Bearing T4A3386 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4" (NRP) 4.30 mm x 0.60 mm Hospital Tip 4 2" x 4 2" 4.30 mm x 4.30 mm Hospital Tip 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) 5" x 4 2" 27 mm x 4.30 mm Hospital Tip 680 P AP A B D D E 0BE (SS) S 0B (SS) D-HT NRP B-NRP D-NRP D-NRP P D D-NRP D-HT A B D D H 32D-HT " x 4 2" 27 mm x 4.30 mm (NRP) 5" x 5" 27 mm x 27 mm 6" x 5" 52.4 mm x 27 mm 6" x 5" 52.4 mm x 27 mm (NRP) Non-Ferrous Heavy Weight 5 Knuckle Bearing T4B3386 Code 50 T6B3386 Code NRP B-NRP D-NRP D-NRP P A B D D P A B D D D-NRP McKinney Full Mortise Hinges 6" x 6" 52.4 mm x 52.4 mm 6462 P A B D D " x 8" mm x mm D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-5

26 s are effective September 0, 208 McKinney Full Mortise Hinges Non-Ferrous Heavy Weight 5 Knuckle Bearing TCA3386 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm Wide throw not available in TCA Series 6836 P A B D D P A B D D P A B D D P A B D D Non-Ferrous Heavy Weight 5 Knuckle Bearing T4A3386 Code " x 5" 4.30 mm x 27 mm Continued 4 2" x 6" 4.30 mm x 52.4 mm 4 2" x 7" 0.60 mm x 77.8 mm 4 2" x 8" 4.30 mm x mm 5" x 6" 27 mm x 52.4 mm 5" x 7" 27 mm x 77.8 mm 5" x 8" 27 mm x mm 7052 P A B D D P A B D D P A B D D P A B D D P A B D D P A B D D Continued on next column Canada: FM-6 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

27 s are effective September 0, 208 Heavy Weight Stainless Steel Swing Clear T4A3395 Code 50 Hinges are NRP Steel Heavy Weight 2 Knuckle Bearing TA3750 Code " 4.30 mm 5" 27 mm D D McKinney Full Mortise Hinges 4 2" x 4 2" 4.30 mm x 4.30 mm R.H P L.H P R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D " x 4 2" 27 mm x 4.30 mm R.H P L.H P R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D " x 5" 27 mm x 27 mm R.H P L.H P R.H AP L.H AP R.H L.H R.H L.H R.H L.H R.H A L.H A R.H B L.H B R.H L.H R.H D L.H D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-7

28 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Heavy Weight 5 Knuckle Bearing T4A3786 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm (NRP) 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) 5" x 4 2" 27 mm x 4.30 mm D B P AP A B E 0BE D D P-NRP NRP D-NRP P AP A B E 0BE D D-NRP " x 4 2" 27 mm x 4.30 mm (NRP) 5" x 5" 27 mm x 27 mm 6" x 5" 52.4 mm x 27 mm 6" x 6" 52.4 mm x 52.4 mm Steel Heavy Weight Wide Throw 5 Knuckle Bearing T4A3786 Code " x 5" 4.30 mm x 27 mm 7270 P AP A B D " x 6" 4.30 mm x 52.4 mm 4 2" x 7" 0.60 mm x 77.8 mm P-NRP D-NRP P AP A B D P AP A B D P AP A B D P AP A B D P AP A B D Continued on next page Canada: FM-8 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

29 s are effective September 0, 208 Steel Heavy Weight Wide Throw 5 Knuckle Bearing Continued T4A3786 Code " x 8" 0.60 mm x mm 5" x 6" 27 mm x 52.4 mm 7280 P AP A B D P AP A B D Steel Heavy Weight 5 Knuckle Concealed Bearing TCA3786 Code 50 5" x 7" 27 mm x 77.8 mm 5" x 8" 27 mm x mm 7290 P AP A B D P AP A B D Steel Heavy Weight 6-Bearing T6A3786 Code 50 McKinney Full Mortise Hinges 4 2" x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 5" x 5" 27 mm x 27 mm P AP A B D P AP A B D P AP A B D " x 6" mm x 52.4 mm P AP A B D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-9

30 s are effective September 0, 208 McKinney Full Mortise Hinges Steel Heavy Weight Swing Clear 5 Knuckle Bearing T4A3795 Code 50 Steel Swing Clear Heavy Weight Beveled Edge Bearing T4A4795 Code " 4.30 mm 5" 27 mm P AP A B D P AP A B D " 4.30 mm 5" 27 mm P AP A B D P AP A B D Hinges are NRP, reversible and non-handed. MacPro Hinges Steel Standard Weight 5 Knuckle MP79 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm P B D P NRP NRP NRP B NRP NRP D NRP 5.42 MacPro Hinge Pin Stop Code 57 For 4 2" : MP79 & MPB " x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm P B E 0BE D P NRP NRP NRP B NRP E 0BE NRP NRP D NRP No. Description MacPro Hinge Pin Stop 26D Canada: FM-20 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

31 s are effective September 0, 208 MacPro Steel Standard Weight Five Knuckle Bearing MPB79 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm (NRP) P B E 0BE D P NRP NRP NRP B NRP NRP D NRP " x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm (NRP) P B E 0BE D P NRP NRP NRP B NRP E 0BE NRP NRP D NRP NRP NRP McKinney Full Mortise Hinges MacPro Steel Heavy Weight Five Knuckle Bearing MPB68 Code 57 MacPro Non-Ferrous Heavy Weight Five Knuckle Bearing MPB99 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm D E 0BE D NRP D E 0BE D NRP " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm D D NRP D D NRP MacPro Non-Ferrous Standard Weight Five Knuckle Bearing MPB9 Code " x 4 2" 4.30 mm x 4.30 mm D D NRP Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FM-2

32 s are effective September 0, 208 McKinney Electric Hinges Electric Hinges CC-4 TA234 - CC4 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm TA274 - CC4 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm B D D B D D P AP A B D D D P AP A B D D D T4A CC4 Code 59 5" x 4 2" 27 mm x 4.30 mm Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm Electric Hinges CC-6 TA234 - CC6 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 7280 P D TA D TA D T4A D T4A D T4A3795, T4A4795 Code 59 5" 27 mm T4A D T4A D B D D B D D T4A CC4 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm T4A CC4 Code " x 4 2" 4.30 mm x 4.30 mm B D D D D P AP A B D D D TA274 - CC6 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 7300 P AP A B D D D P AP A B D D D Canada: EH- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

33 s are effective September 0, 208 Electric Hinges CC-6 T4A CC6 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm T4A CC6 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm Electric Hinges CC-8 TA234 - CC8 Code B D D D D P AP A B D D D P D Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm T4A3795, T4A4795 Code 59 5" 27 mm 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm TA D TA D T4A D T4A D T4A D T4A D B D D B D D Electric Hinges CC-8 TA274 - CC8 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm T4A CC8 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm T4A CC8 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm 746 P AP A B D D D P AP A B E 0BE D D D B D D D D P AP A B D D D D Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " TA D mm T4A3795, T4A4795 Code 59 5" 27 mm TA D T4A D T4A D T4A D T4A D McKinney Electric Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-2

34 s are effective September 0, 208 McKinney Electric Hinges Electric Hinges QC-2 TA234 - QC2 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm B D D B D D TA274 - QC2 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 732 P AP A B D D D P AP A B D D D T4A QC2 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D T4A QC2 Code " x 4 2" 4.30 mm x 4.30 mm 7344 P AP A B D D D Electric Hinges QC-2 T4A QC2 Code 59 5" x 4 2" 27 mm x 4.30 mm 7356 P D Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm T4A3795, T4A4795 Code 59 5" 27 mm Electric Hinges QC-4 TA234 - QC4 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm B D D B D D TA274 - QC4 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm TA D TA D T4A D T4A D T4A D T4A D P AP A B D D D P AP A B D D D Canada: EH-3 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

35 s are effective September 0, 208 Electric Hinges QC-4 T4A QC4 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D T4A QC4 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P AP A B D D D P D Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm T4A3795, T4A4795 Code 59 5" 27 mm Electric Hinges QC-6 TA234 - QC6 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm TA D TA D T4A D T4A D T4A D T4A D B D D B D D Electric Hinges QC-6 TA274 - QC6 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm P AP A B D D D P AP A B D D D T4A QC6 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D T4A QC6 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P AP A B D D D P D Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm TA D TA D T4A D T4A D McKinney Electric Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-4

36 s are effective September 0, 208 McKinney Electric Hinges Electric Hinges QC-6 Swing Clear Hinges T4A3795, T4A4795 Code 59 5" 27 mm Electric Hinges QC-8 TA234 - QC8 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm B D D B D D TA274 - QC8 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm T4A D T4A D P AP A B D D D P AP A B D D D Electric Hinges QC-8 T4A QC8 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P AP A B D D D D P Swing Clear Hinges TA2895, TA4895, T4A3795, T4A4795 Code " 4.30 mm T4A3795, T4A4795 Code 59 5" 27 mm Electric Hinges QC-0 TA234 - QC0 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm TA D TA D T4A D T4A D T4A D T4A D B D D B D D T4A QC8 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D TA274 - QC0 Code " x 4" 4.30 mm x 0.60 mm 7392 P AP A B D D D Canada: EH-5 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

37 s are effective September 0, 208 Electric Hinges QC-0 TA274 - QC0 Code " x 4 2" 4.30 mm x 4.30 mm P AP A B D D D T4A QC0 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D T4A QC0 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P AP A B D D D P D Electric Hinges QC-2 TA234 - QC2 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm B D D B D D Electric Hinges QC-2 TA274 - QC2 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm P AP A B D D D P AP A B E 0BE D D D T4A QC2 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm B D D D D T4A QC2 Code " x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P AP A B D D D P D McKinney Electric Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-6

38 s are effective September 0, 208 McKinney Electric Hinges MacPro Electric Hinges - Concealed Circuit (CC) Code 57 Product MPB79-CC4 4 2" x 4" D MPB79-CC mm x 0.60 mm D MPB79-CC4 4 2" x 4 2" D MPB79-CC mm x 4.30 mm D MPB68-CC4 4 2" x 4 2" D MPB68-CC mm x 4.30 mm D MacPro Electric Hinges - ElectroLynx Quick Connect (QC) Code 57 Product MPB79-QC4 4 2" x 4" D 9.88 MPB79-QC mm x 0.60 mm D MPB79-QC D MPB79-QC4 4 2" x 4 2" D MPB79-QC mm x 4.30 mm D MPB79-QC D MPB68-QC4 4 2" x 4 2" D MPB68-QC mm x 4.30 mm D MPB68-QC D As part of their promise to provide innovative, fast and effective high security solutions to their customers, certain ASSA ABLOY Group brands offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx is a registered trademark of ASSA ABLOY Inc. Canada: EH-7 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

39 s are effective September 0, 208 Transfer Device Solutions McKinney ElectroLynx Harnesses & Components For Metal Doors CORBIN RUSSWIN, SARGENT, and YALE Code 79 McKinney Electric Hinges If metal door, order a retrofit cable with Molex connectors on both ends. If the metal door is polystyrene filled or steel stiffened, the cable may need to be routed up and over the door. PART # McKinney Catalog # 3", 6" & 2" Harness Between hinge and the end of an exit device 9398 QC-C QC-C006 Description: QC2-3" Wire Harness; 8 & 4 Pin Connector w/2 wires (For Exit Device Rail Jumper to Hinge) QC2-6" Wire Harness; 8 & 4 Pin Connector w/2 wires (For Exit Device Rail Jumper to Hinge) QC2-2" Wire Harness; 8 & 4 Pin Connector w/2 wires QC-C02 (For Exit Device Rail Jumper to Hinge) 2', 3' & 4' Harness Between hinge and through the door to the lockset or exit device trim List Max Hinge required (Not included) QC QC QC QC-C200 QC2-26" Wire Harness; 8 & 4 Pin Connector w/2 Wires 3.92 QC QC-C206 QC2-32" Wire Harness; 8 & 4 Pin Connector w/2 Wires QC QC-C300 QC2-38" Wire Harness; 8 & 4 Pin Connector w/2 wires QC QC-C306 QC2-44" Wire Harness; 8 & 4 Pin Connector w/2 wires QC QC-C400 QC2-50" Wire Harness; 8 & 4 Pin Connector w/2 wires QC2 5' Harness From the hinge location, up the jamb to the above the ceiling, or up and around a full lite or half lite metal door QC-C500 QC2-5' 2" Wire Harness; 8 & 4 Pin Connector w/2 Wires QC2 Custom * QC2 - Custom sizes available. Consult factory. Harness; 8 & 4 Pin Connector w/2 Wires POA QC2 QC-C or QC-CP x 60 = $38.30, x 72 = $45.96, 82 = $52.34, 96" = $6.50, 08 = $69.2. For sizes 0'-20' $2.00, 2' - 30' $45.60, 3' - 40' $70.00, 4' - 50' $94.60, 50' = $ Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-8

40 s are effective September 0, 208 McKinney Electric Hinges Transfer Device Solutions McKINNEY ElectroLynx Harnesses & Components For Wood Doors CORBIN RUSSWIN, SARGENT, and YALE Code 79 If wood door, order a retrofit cable with the Molex connector on one end, and pins crimped on the other end. PART # McKinney CATALOG # 3", 6" & 2" Harness Between hinge and the end of an exit device Description: QC-C003P QC2-3" Wire Harness; 8 & 4 Pin Connector w/2 wires (For Exit Device Rail Jumper to Hinge, Insert pre-pinned ends into plastic Molex connector) QC2-6" Wire Harness; 8 & 4 Pin Connector w/2 wires 9399 QC-C006P (For Exit Device Rail Jumper to Hinge, Insert pre-pinned ends into plastic Molex connector) QC2-2" Wire Harness; 8 & 4 Pin Connector w/2 wires QC-C02P (For Exit Device Rail Jumper to Hinge, Insert pre-pinned ends into plastic Molex connector) 2', 3' & 4' Harness Between hinge and through the door to the lockset or exit device trim QC-C200P QC2-26" Wire Harness; 8 & 4 Pin Connector w/2 wires (Insert pre-pinned ends into plastic Molex connector) List Max Hinge required (Not included) QC QC QC QC QC-C206P QC-C300P QC-C306P QC2-32" Wire Harness; 8 & 4 Pin Connector w/2 wires (Insert pre-pinned ends into plastic Molex connector) QC2-38" Wire Harness; 8 & 4 Pin Connector w/2 wires (Insert pre-pinned ends into plastic Molex connector) QC2-44" Wire Harness; 8 & 4 Pin Connector w/2 wires (Insert pre-pinned ends into plastic Molex connector) 40.6 QC QC QC QC-C400P QC2-50" Wire Harness; 8 & 4 Pin Connector w/2 wires (Insert pre-pinned ends into plastic Molex connector) 5' Harness From the hinge location, up the jamb to the above the ceiling, or up and around a full lite or half lite metal door. QC2-5' 2" Wire Harness; 8 & 4 Pin Connector w/2 Wires QC-C500P (Termination in Field) QC QC QC-C2500P QC2-25' Wire Harness, 8 & 4 Pin Connector w/2 Wires QC QC-C3000P QC2-30' Wire Harness; 8 & 4 Pin Connector w/2 Wires 9.22 QC2 Custom * Custom sizes available. Consult the factory POA QC2 * QC-CP 0 FT $56.60, QC-CP 20 FT $3.20, QC-CP 50 FT 65.6, QC-CP 70 FT $23.32, QC-CP 75 FT $ $ for QC-C or QC-CP x 50 ft. $ for QC-C or QC-CP x 50 ft. Check our websites for Canada: EH-9 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

41 s are effective September 0, 208 Transfer Device Solutions McKinney ElectroLynx Harnesses & Components CORBIN RUSSWIN, SARGENT, and YALE McKinney PART # CATALOG # Miscellaneous Kits Description: QC-R00 Molex/Repair/Service Kit Miscellaneous Kits Code 79 Kit Application: Includes 2, 4, 8 Molex receptacles and plugs ( 0 ea) and the corresponding terminals (00 of each type), extraction tool and pinning assembly guide. Customer must purchase Molex crimper separately. List McKinney Electric Hinges QC-R002 Extraction Tool Quantity, Sold one each QC-R003 Molex Hand Crimp Tool Molex tool used to attach terminals to wire (stripped) ends PART # McKinney CATALOG # Receptacles and Terminals Description: Kit Application: List QC-RF2 Female Receptacle 2 CKT Quantity Bag of QC-RF4 Female Receptacle 4 CKT Quantity Bag of QC-RF8 Female Receptacle 8 CKT Quantity Bag of QC-RM2 Male Plug 2 CKT Quantity Bag of QC-RM4 Male Plug 4 CKT Quantity Bag of QC-RM8 Male Plug 8 CKT Quantity Bag of QC-FT2024 Female Terminal AWG Quantity Bag of QC-FT2630 Female Terminal AWG Quantity Bag of QC-MT2024 Male Terminal AWG Quantity Bag of QC-MT2630 Male Terminal AWG Quantity Bag of QC-DCC Pinning Assembly Guide Quantity Bag of POE-MT2024 Male Terminal AWG Quantity Bag of POE-RM6 Male Plug 6 CKT Quantity, Bag of POE-RF6 Female Receptacle 6 CKT Quantity, Bag of POE-MT2630 Male Terminal AWG Quantity, Bag of POE-FT2630 Female Terminal AWG Quantity, Bag of Female Receptacle (8 ckt) Locking mechanism Male Plug (8 ckt) Door Cord and EPT MCK-TSB-C Door Cord Gray/Black Caps 8" Quantity, Sold MCK-TSB-CXL Door Cord Gray/Black Caps 36" Quantity, Sold MCK-EPT Electrical Power Transfer Quantity, Sold MCK-EPTL Electrical Power Transfer, Long Quantity, Sold MCK-EL-EPT ElectroLynx EPT -2 wire Quantity, Sold MCK-EL-EPTL ElectroLynx EPTL Long -2 wire Quantity, Sold As part of their promise to provide innovative, fast and effective high security solutions to their customers, ASSA ABLOY Group brands offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx is a registered trademark of ASSA ABLOY Inc. Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-0

42 s are effective September 0, 208 McKinney Electric Hinges Transfer Device Solutions McKinney ElectroLynx Power over Ethernet (PoE) Hinge & Harnesses Code 79 Frame side harness assembly (5ft length) Cable drain wire concealed in shrink tubing Cable - CAT 5e, 24 AWG stranded, shielded, 00ohm, with drain wire A Cable wires to be terminated in field per lock instructions Frame Side Harness Assembly B PART # PoE Data Hinge PoE Hinges are Code 59 McKinney CATALOG # U.S. Patent No. 7,824,200 PoE Door Harness Assembly C Cable - CAT 5e, 26 AWG stranded, shielded, 00ohm Description: Two 4-CKT lock mating connectors List x 4.5 TA274 26D PoE Standard Weight 5 Knuckle, x 4.5 T4A D PoE Heavy Weight 5 Knuckle, Consult the factory for additional items with PoE option. Lock mating connectors are small enough to run through a 3/8" (min.) stile to stile door raceway. Ring terminal to be NOTES: secured inside lock The PoE door & frame harnesses can accommodate a variety of new (with raceway) and retrofit applications. Connectors are small enough to run through a 3/8" (min.) stile-to-stile door raceway. Connects to intelligent Power over Ethernet electromechanical hardware from SARGENT and CORBIN RUSSWIN. PART # McKinney CATALOG # Harness Length Application Description: List Max Hinge Req'd (not included) Door Harnesses PoE-C206P 30" PoE-C300P 36" PoE-C306P 42" PoE-C400P 48" 9404 PoE-C406P 54" Between Hinge & PoE Lock PoE-C500P 60" Door Harness Assembly 9402 PoE-C700P 84" Door Harness Assembly PoE-C300P 56" Door Harness Assembly EPT Harness PoE-CEPT30 360" EPT Harness Assembly EPT Harness Frame Harness PoE-C500P 80" 20" to 25" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 26" to 3" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 32" to 36" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 37" to 42" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 43" to 48" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). From the hinge location, up the jamb to the wall/ceiling. PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly Between hinge and PoE Network Cable & Switch PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE PoE PoE PoE PoE 8.62 PoE PoE PoE PoE PoE Custom Custom sizes available. Consult factory. POA PoE The door harness connectors are small enough to run through a 3/8" (minimum) stile-to-stile door raceway. *See the McKinney Catalog for additional finishes and hinge types. Note: One hinge, door harness and frame harness are required for each PoE opening. Custom cables less than 20 FT $ POE-C500P 80 in (5 FT) - POE-C2500P in (25 FT) $ FT $ Check our websites for Canada: EH- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

43 s are effective September 0, 208 Transfer Device Solutions McKinney ElectroLynx Power over Ethernet (PoE) Harnesses with Loose RJ-45 Connectors Code 79 Cable wires to be terminated in field per lock instructions McKinney Electric Hinges Frame side harness assembly (5ft length) Cable drain wire concealed in shrink tubing Cable - CAT 5e, 24 AWG stranded, shielded, 00ohm, with drain wire A Frame Side Harness Assembly B PoE Data Hinge PoE Door Harness Assembly C Cable - CAT 5e, 26 AWG stranded, shielded, 00ohm RJ-45 Connector Ring terminal to be secured inside lock NOTES: The PoE door & frame harnesses can accommodate a variety of new (with raceway) and retrofit applications. Connects to next generation Power over Ethernet electromechanical hardware from SARGENT and CORBIN RUSSWIN including: Corbin Russwin IN220, Corbin Russwin Access 700 PIP, SARGENT IN220, SARGENT Passport 000 P. PART # McKinney CATALOG # Harness Length Application Description: List Max Hinge Req'd (not included) Door Harnesses PoE-C206RJ 30" PoE-C300RJ 36" PoE-C306RJ 42" PoE-C400RJ 48" PoE-C406RJ 54" Between Hinge & PoE Lock PoE-C500RJ 60" Door Harness Assembly 9420 PoE-C700RJ 84" Door Harness Assembly PoE-C300RJ 56" Door Harness Assembly 20" to 25" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 26" to 3" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 32" to 36" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 37" to 42" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 43" to 48" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE PoE PoE PoE PoE 8.62 PoE PoE PoE EPT Harness PoE-CEPT30RJ 360" EPT Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, PoE Door Frame Harness Assembly Custom Custom sizes available. Consult factory. POA PoE Note: One hinge, door harness and frame harness are required for each PoE opening. POE-C500RJ 80 in (5 FT) - POE-C2500RJ $ in (25 FT) $ FT $ Canada: Check our websites for Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in EH-2

44 s are effective September 0, 208 McKinney Electric Hinges Transfer Device Solutions McKinney ElectroLynx Power over Ethernet (PoE) Harnesses with RJ-45 Connectors Attached Code 79 Cable wires to be terminated in field per lock instructions Frame side harness assembly (5ft length) Cable drain wire concealed in shrink tubing Cable - CAT 5e, 24 AWG stranded, shielded, 00ohm, with drain wire A Frame Side Harness Assembly B PoE Data Hinge PoE Door Harness Assembly C Cable - CAT 5e, 26 AWG stranded, shielded, 00ohm RJ-45 Connector Ring terminal to be NOTES: secured inside lock The PoE door & frame harnesses can accommodate a variety of new (with raceway) and retrofit applications. Connects to next generation Power over Ethernet electromechanical hardware from SARGENT and CORBIN RUSSWIN including: Corbin Russwin IN220, Corbin Russwin Access 700 PIP, SARGENT IN220, SARGENT Passport 000 P. PART # McKinney CATALOG # Harness Length Application Description: List Max Hinge Req'd (not included) Door Harnesses 9420 PoE-C206PRJ 30" 942 PoE-C300PRJ 36" 9422 PoE-C306PRJ 42" 9423 PoE-C400PRJ 48" 9424 PoE-C406PRJ 54" Between Hinge & PoE Lock 9425 PoE-C500PRJ 60" Door Harness Assembly 9426 PoE-C700PRJ 84" Door Harness Assembly 9427 PoE-C300PRJ 56" Door Harness Assembly 20" to 25" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 26" to 3" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 32" to 36" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 37" to 42" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). 43" to 48" door width (doors with 3 butt hinges with PoE hinge in center stile-to-stile raceway to lock prep). PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, Cat 5e, 26AWG, Shielded, Screened,00ohm, Door Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE, CAT 5e, 26AWG, Shielded, Stranded, 00ohm, Door Frame Harness Assembly PoE PoE PoE PoE PoE 8.62 PoE PoE PoE Custom Custom sizes available. Consult factory. POA PoE Note: One hinge, door harness and frame harness are required for each PoE opening. Custom cables less than 60" are priced at the 60" price. For custom cables greater than 60", add $.62 per inch to the 60" price. PoE-C500PRJ (5 FT) $6.4 E-C2500PRJ (25 FT) $27.70 E-C3000PRJ (30 FT) $39.24 For QC Cable Only $2.00 per foot (code 79X) Example below. 000 FT 2 WIRE QC-CABLE ONLY Check our websites for Canada: EH-3 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

45 s are effective September 0, 208 Non-Ferrous Bearing TA39 Code 30 5" x 4 2" 27 mm x 4.30 mm Non-Ferrous Bearing TA393 Code 30 5" x 4 2" 27 mm x 4.30 mm McKinney Full Mortise Anchor Hinge Sets Anchor plate for jamb and door header only. Permits use of holders, closers concealed in top of jamb. Anchor plate for jamb header only, permits the use of holders and closers concealed in the top of the door. Hand Hand R.H D, SET R.H D,36.84 SET L.H D, SET R.H D, SET 4 SETS SET 28 L.H D,36.84 SET R.H D, SET 4 SETS SET 28 L.H D, SET L.H D, SET Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. TA392 Code 30 5" x 4 2" 27 mm x 4.30 mm Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. Non-Ferrous Bearing Hinges 4" Door Leg TA394 Code 30 5" x 4 2" 27 mm x 4.30 mm Anchor plate for jamb and door header permits use of surface applied holders and closers. Anchor plate for both jamb and door header. Permits use of both holders, closers. Hand Hand R.H D, SET R.H D,37.48 SET L.H D, SET R.H D SET 4 SETS SET 28 L.H D,37.48 SET R.H D, SET 4 SETS SET 28 L.H D SET L.H D, SET Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in AH-

46 s are effective September 0, 208 McKinney Full Mortise Anchor Hinge Sets Heavy Weight Beveled Edge Non-Ferrous Bearing TA5392 Code 30 5" x 4 2" 27 mm x 4.30 mm Non-Ferrous Bearing Hinges For Beveled Edge Doors 4" Door Leg TA5394 Code 30 5" x 4 2" 27 mm x 4.30 mm Anchor plate for both jamb and door header permits use of surface applied holders and closers. Anchor plate for both jamb and door header permits use of surface applied holders and closers. Hand R.H D, SET L.H D, SET R.H D SET L.H D SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. TA5393 Code 30 5" x 4 2" 27 mm x 4.30 mm Hand R.H D,37.48 SET L.H D,37.48 SET R.H D, SET L.H D, SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. Steel Anchor Hinge Bearing TA79 Code 30 5" x 4 2" 27 mm x 4.30 mm Anchor plate for jamb header only, permits the use of holders and closers concealed in the top of the door. Anchor plate for door header only. Permits use of holders, closers concealed in top of jamb. Hand R.H D,36.84 SET L.H D,36.84 SET R.H D,39.24 SET L.H D,39.24 SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. Hand R.H D SET L.H D SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. Canada: AH-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

47 s are effective September 0, 208 Steel Anchor Hinge Bearing TA792 Code 30 5" x 4 2" 27 mm x 4.30 mm Steel Anchor Hinge 4" Door Leg TA794 Code 30 5" x 4 2" 27 mm x 4.30 mm McKinney Full Mortise Anchor Hinge Sets Anchor plate for jamb and door header permits use of surface applied holders and closers. Anchor plate for both jamb and door header permits use of surface applied holders and closers. Hand Hand R.H D SET L.H D SET 4 SETS SET 28 R.H D L.H D SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. TA793 Code 30 5" x 4 2" 27 mm x 4.30 mm Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. Steel Heavy Weight Beveled Edge Bearing TA5792 Code 30 5" x 4 2" 27 mm x 4.30 mm Anchor plate for jamb header only, permits the use of holders and closers concealed in top of the door. Hand R.H D SET L.H D SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for square edge door application. Anchor Hinge Sets are not available in brite finishes. Anchor plate for jamb and door header permits use of surface applied holders and closers. Hand R.H D SET L.H D SET 4 SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in AH-3

48 s are effective September 0, 208 McKinney Full Mortise Anchor Hinge Sets Steel Heavy Weight Beveled Edge Bearing TA5793 Code 30 5" x 4 2" 27 mm x 4.30 mm Steel Bearing Hinges For Beveled Edge Doors 4" Door Leg TA5794 Code 30 5" x 4 2" 27 mm x 4.30 mm Anchor plate for jamb header only, permits the use of holders and closers concealed in top of the door. Anchor plate for both jamb and door header permits use of surface applied holders and closers. Hand R.H D SET 4 SETS SET 28 L.H D SET Hand R.H D L.H D SETS SET 28 Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. Set consists of top anchor, intermediate and bottom hinge for beveled ( 8" in 2") edge doors on hinge side application. Anchor Hinge Sets are not available in brite finishes. Reinforcing Pivots 8540 Code Code 20 4" 0.60 mm 4" 0.60 mm Hand Hand R.H L.H R.H D L.H D Code Code " 4.30 mm 4 2" 4.30 mm Hand Hand R.H L.H R.H D.60 L.H D Canada: AH-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

49 s are effective September 0, 208 Steel Five Knuckle Standard Weight TA2774 Code 50 Standard Weight Five Knuckle Non-Ferrous Bearing TA3374 Code 50 McKinney Half Mortise Hinges 4 2" 4.30 mm 5" 27 mm P AP A B D P AP A B D " 4.30 mm 5" 27 mm 6406 P AP A B D D P AP A B D D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in HM-

50 s are effective September 0, 208 McKinney Half Mortise Hinges Heavy Weight Non-Ferrous Bearing T4A3384 Code 50 Steel Heavy Weight Bearings T4A3784 Code " 4.30 mm 5" 27 mm 6" 52.4 mm for 3 4" 44.4 mm door P AP A B D D P AP A B D D P AP A B D " 4.30 mm 5" 27 mm 6" 52.4 mm for 3 4" 44.4 mm door P AP A B D P AP A B D P AP A B D Steel Swing Clear Heavy Weight Bearing T4A3789 Code 30 5" 27 mm 7302 P AP A B D Canada: HM-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

51 s are effective September 0, 208 Standard Weight Non-Ferrous Bearing TA2372 Code 50 HeavyWeightNon-FerrousBearing T4A3382 Code 50 McKinney Half Surface Hinges 4 2" 4.30 mm 5" 27 mm Refer to page HS-3 for Back Plates AP P B D D D D D Steel Standard Weight TA2772 Code " 4.30 mm 5" 27 mm Refer to page HS-3 for Back Plates P AP A B D P AP A B D " 4.30 mm 5" 27 mm 6" 52.4 mm Refer to page HS-3 for Back Plates. HeavyWeightSteelBearing T4A3796 Code 50 5" 27 mm P AP A B D D P AP A B D D P AP A B, D P AP A B D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in HS-

52 s are effective September 0, 208 McKinney Half Surface Hinges Steel Heavy Weight Bearing T4A3782 Code 50 Steel Back Plates BP-0 BP- Code " 4.30 mm 5" 27 mm 6" 52.4 mm for 3 4" 44.4 mm door 6" 52.4 mm for 2 4" 5.05mm door 5805 P AP A B D P AP A B D P AP A B D D " 4.30 mm 5" 27 mm Product BP-0 (TA2772) (T4A3782) 6324 P B D P D AS ORDERED AS ORDERED Canada: HS-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

53 s are effective September 0, 208 Heavy Weight 5 Knuckle Non-Ferrous Bearing T4A338 Code 50 Steel Standard Weight 5 Knuckle Bearing TA277 Code 50 McKinney Full Surface Hinges 4 2" 4.30 mm 5" 27 mm 6" mm 655 P AP A B D D P AP A B D D P AP A B D " 4.30 mm 5" 27 mm Steel Heavy Weight Bearing T4A378 Code " 4.30 mm 5" 27 mm 6" mm P AP A B D P AP A B D P AP A B D P AP A B D P AP A B D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in FS-

54 s are effective September 0, 208 McKinney Spring Hinges Steel Standard Weight Full Mortise Single Acting 502 Code 7 C US LISTED 4" x 4" 0.60 mm x 0.60 mm 4 2" x 4" 4.30 mm x 0.60 mm 5593 P AP A B D RC-26D D D P AP A B D D D " x 4 2" 5607 P mm x 4.30 mm 5608 AP A B E 0BE D D D Reverse Spring 502R Code " x 4 2" P mm x 4.30 mm D For other finishes of 502 R add $3.50 to the 502 price. 502 x TRS Option $7.00. NOTE: Consult the Factory for information on our 502 with new Security Feature. 522 Code 7 No. Fin. Per Set 4 2" x 4" 5598 P SET 4.30 mm x 0.60 mm AP SET SET SET SET A SET B SET 56045E 0BE 63.72SET SET D SET D SET D SET SET SET SET C US LISTED Set 6 SETS SET 54 Stainless Steel Standard Weight 552 Code 7 No. Fin. Per Set 4 2" x 4 2" 5604 P 5.36 SET 4.30 mm x 4.30 mm AP SET SET SET SET A 65.78SET B 90.08SET SET D SET D SET D SET SET SET SET 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm Set 6 SETS SET D EA D 5.88 EA Allen Wrench set for 502 / 522 / 552 Spring Hinges $4.50 per set Canada: SH- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

55 s are effective September 0, 208 MacPro Spring Hinges MPS60 Code " x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm MPS679 Code 57 MK0379 Code 57 C US LISTED P D E 0BE 5.26 C US LISTED D SETS SET 30 Fin. Set includes 2 Spring Hinges and Bearing Hinge. Cross pin for MPS60 Wrench is No. Fin ea..00 ea. Steel Door Spring Adjustable Tension Code 72 Per Set Set " mm D EA "279.4mm D EA "330.2mm D4 3.0 EA Steel Full Mortise Double Acting Simplex Butt 00 Code 72 3" mm 4" 0.60 mm 5" 27 mm 6" 52.4 mm 6" x 4 2" 52.4 mm x 4.30 mm P D C D P D C A D P AP D C D P D C A D P D C A D McKinney Spring Hinges Steel Full Mortise Double Acting Simplex Butt Non-Template 900 Code 72 See page SH-4 for replacement parts. 8" mm P AP D C A D Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in SH-2

56 s are effective September 0, 208 McKinney Spring Hinges Steel Full Mortise Double Acting Simplex Clamp Flange Butt 900 Code 72 HS00 Code 72 8" mm 5933 P AP D C A D See page SH-4 for replacement parts " mm 4" 0.60 mm P AP D C A D P AP D C A D 2.36 See page SH-4 for replacement parts Ajax Double Acting Horizontal Pivot Hinge 300 Code 72 Ajax Double Acting Horizontal Pivot Hinge With Jamb Attaching Plate J300 Code P D C A D SET / J300 SERIES list price TOP PIVOT & SOCKET 9.40 JAMB ATTACHING PLATE* SIDE PLATE* BACK PLATE* *Specify finish when ordering. 576 P D C A D 2.56 For concrete or tile floor installation 0 SET 33 Canada: SH-3 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

57 s are effective September 0, 208 Ajax Double Acting Horizontal Pivot Hinge 4007RB Code 72 Reversed Brackets 8007 Code 72 McKinney Spring Hinges 4007-MRB Code P D C A D SET 35 Mortised and Reversed Brackets H8007 Code P D C A D SET P D C A D SET P D C A D SET RB/4007-MRB Series Replacement s TENSION PIN 3.70 NYLON BUSHINGS 2.40 TENSION RODS 3.30 No replacement parts are available. *Specify part number, size and finish when ordering. REPLACEMENT PARTS FOR DOUBLE ACTING SPRING HINGES AND PIVOTS McKINNEY Description Needed 3" 4" 5" 6" 6x4 2" 8" 8" Required Per Hinge T53 - Spring T56 Tension Pin TS550 Solid Metal Cap X TS50 Loose Knob X TS520 Fast Knob TS525 Pawlnut X 4 x x x x 4.28 x x TS530 Tension Lever TS540 Plug X x x x.4.4 x x Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in SH-4

58 s are effective September 0, 208 McKinney Rescue Hardware Top Pivot and Socket EP-5J Code Per Set P D EP-5J Top Pivot and Socket $6.80. EP-5J Bottom Bracket and Bottom Door Socket $9.00. Screws for EP-5J $3.00 ea. For Cylindrical or Bored Locks CSS-9 Code May not work with mortise locks. Consult the factory for mortise lock application. Not for use with deadbolt. and Plunger Assembly for DS-6 or CSS-9 $ only $7.00. Springs only $ /2x2-32 Torx MS 2D 5 3 4" 46 mm 5 7 8" mm 6 3 4" 7.40 mm Center Hung D Offset Hung D Center Hung D Offset Hung D Center Hung D Offset Hung D Custom s As Ordered Emergency Door Stop DS-6 Code Consult the factory for availability of custom sizes Custom Engineering and Set Up charges may apply. Per Set D Double Lipped Strike DLS-8 Code May not work with mortise locks. Consult the factory for mortise lock application. Not for use with deadbolt. Consult the factory for availability of custom sizes Custom Engineering and Set Up charges may apply " 46 mm 6 3 4" 7.40 mm 5 7 8" mm 7 3 4" mm 8 4" mm Center Hung D Offset Hung D Center Hung D Offset Hung D Center Hung D Center Hung D Center Hung D Custom As Ordered MK X/2 TORX SC FOR CSS-9 /DLS8 $.64 each. Canada: RH- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

59 s are effective September 0, 208 Raised Barrel Code " x 4 2" 4.30 mm x 4.30 mm RBTA RBT4A D D McKinney Specialty Hinges Pocket Hinge PH-4 Code For Narrow Stile D AS ORDERED StormPro Tornado Resistant Hinges SP3386 Code 50 Other finishes available upon request. 4 2" x 4 2" 4.30 mm x 4.30 mm 4 2" x 4 2" 4.30 mm x 4.30 mm NRP 5" x 4 2" 27 mm x 4.30 mm D D D SP3786 Code 50 All StormPro products should be ordered as a complete integrated unit including the frame and door along with other StormPro hardware. Storm- Pro hinges are a required component of the certified StormPro system 4 2" x 4 2" 4.30 mm x 4.30 mm 5" x 4 2" 27 mm x 4.30 mm P D P D Interim Hinges Code 50 For finishes not listed, use $4.00 over 26D price Door or Frame Leaf Opposite Leaf Trimmed To: 5" 4½" TA274 26D T4A D T4A D All interim hinges are supplied with NRP set screw and nohole plugs which allow them to be reversible. Leaves are trimmed the same dimension from the top and bottom of that leaf - otherwise a complete special must be manufactured, check for existence of available special part numbers which may have previously been manufactured Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in SP-

60 s are effective September 0, 208 McKinney Specialty Hinges Specialty Hinges & Residential 400 Code 4 Staggered Hole Pattern on 4" x 4" 3 2" x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm B* D B* D Code 4 /4" Radius Staggered Hole Pattern on 4" x 4" 3 2" x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm B* D B* D Code 4 5/8" Radius Staggered Hole Pattern on 4" x 4" Residential Hinges available only in finishes shown above. Contract Grade Hinge Discount does not apply to Residential Grade Hinges. NOTE: Unlisted finishes for residential hinges P.O.A. Consult the Factory on minimum requirements. Residential Grade Swing Clear Hinges T2895 Code " mm /4RC NL US /8RC NL US /4RC NL US /8RC NL US /4RC NL 0BE /8RC NL 0BE T2895 Code 50 4" 0.60 mm /4RC NL US /4RC NL US /4RC NL U0BE Swage Hinges RCTA234 Code " x 4" 4.30 mm x 0.60 mm D-NRP D3-NRP D4-NRP " x 3 2" mm x mm 4" x 4" 0.60 mm x 0.60 mm B* D B* D 6.26 *Residential grade 0B. Residential Grade Single Acting Spring Hinges 502 Code " x 3 2" mm x mm 552 Code P A B E 0BE D D " x 3 2" mm x mm D Canada: SP-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

61 s are effective September 0, Knuckle Architectural Hinges Code 20 *GT and LT tips not available in D4 and 0BE finishes. For options not offered in price book, contact factory. 2-Knuckle Hinges are handed RH or LH. Concealed Hinges Code 20 McKinney Designer Hardware FT LH RH Tip Prefix FT GT LT RT Hinge Hinge Type RT TA " x 4" 4.30 mm x 0.60 mm LH RH Tip Prefix FT GT LT RT Hinge Hinge Type TA273 5" x 5" 27 mm x 27 mm GT* Hinge Hinge Tips LT* Book D4 x US D4 x US D4 x US D4 x US26D 89.0 D4 x D BE x 0BE 80.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE 3.72 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D " x 7 8" MK40A MK67002 Satin Chrome mm x 23 mm MK67003 Matte Black 0.00 MK80 MK80A 4 3 8" x 8" MK67004 Satin Chrome MK67005 Matte Black mm x 29 mm 4 3 8" x 8" MK67006 Satin Chrome MK67007 Matte Black mm x 29 mm LH RH Tip Prefix FT GT LT RT Hinge Hinge Type TA " x 4 2" 4.30 mm x 4.30 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D 89.0 D4 x D BE x 0BE 80.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D MK00 6 4" x 6" MK67000 Satin Chrome MK6700 Matte Black mm x 28 mm Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in DH-

62 s are effective September 0, 208 McKinney Designer Hardware 3-Knuckle Architectural Hinges Code 30 *GT and LT tips not available in D4 and 0BE finishes.for options not offered in price book, contact factory. Tip Prefix FT GT LT RT FT Hinge Hinge Type TA74 4" x 4" 0.60 mm x 0.60 mm Hinge Hinge Tips RT Book D4 x US D4 x US D4 x US D4 x US26D 56.4 D4 x D BE x 0BE 56.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Tip Prefix FT GT LT RT GT* Hinge Hinge Type TA74 5" x 5" 27 mm x 27 mm Hinge Hinge LT* Tips Book D4 x US D4 x US D4 x US D4 x US26D 80.4 D4 x D BE x 0BE 80.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Tip Prefix FT GT LT RT 7802 Hinge Hinge Type TA74 4 2" x 4" 4.30 mm x 0.60 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Order by Description Tip Prefix FT Hinge Hinge Type TA " x 4 2" 4.30 mm x 4.30 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US3 x US US4 x D US5 x D US26 x D US26D x D US4 x US US5 x US US4 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Tip Prefix FT GT LT RT Hinge Hinge Type TA74 4 2" x 4 2" 4.30 mm x 4.30 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Order by Description Tip Prefix FT Hinge Hinge Type TA786 5" x 5" 27 mm x 27 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D 3.84 D4 x D BE x 0BE 3.84 US4 x D US5 x D US26 x D US26D x D US4 x US US5 x US US4 x US US5 x US US26 x US26D 3.84 US26D x US US26 x US US26D x US26D Canada: DH-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

63 s are effective September 0, Knuckle Architectural Hinges Code 50 5-Knuckle Architectural Hinges Split only available with Standard Pin and Plug. For options not offered in price book, contact factory. McKinney Designer Hardware Hinge Type T274 Hinge 4" x 4" 0.60 mm x 0.60 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Hinge Type TA274 Hinge 4" x 4" 0.60 mm x 0.60 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D 56.4 D4 x D BE x 0BE 56.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Hinge Type T274 Hinge 4 2" x 4" 4.30 mm x 0.60 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D US4 x D US5 x D US26 x D US26D x D US4 x US US5 x US US26 x US26D US26D x US Hinge Type TA274 Hinge 4 2" x 4" 4.30 mm x 0.60 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Hinge Type T274 Hinge 4 2" x 4 2" 4.30 mm x 4.30 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D 40.0 US26D x US US26 x US US26D x US26D Hinge Type T274 Hinge 5" x 5" 27 mm x 27 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Continued on next page Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in DH-3

64 s are effective September 0, 208 McKinney Designer Hardware 5-Knuckle Architectural Hinges (Continued) Code 50 5-Knuckle Architectural Hinges Split only available with Standard Pin and Plug. For options not offered in price book, contact factory Hinge Type TA274 Hinge 4 2" x 4 2" 4.30 mm x 4.30 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D D4 x D BE x 0BE US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Hinge Type TA274 Hinge 5" x 5" 27 mm x 27 mm Hinge Hinge Tips Book D4 x US D4 x US D4 x US D4 x US26D 80.4 D4 x D BE x 0BE 80.4 US4 x D US5 x D US26 x D US26D x D US4 x US US4 x US US5 x US US5 x US US26 x US26D US26D x US US26 x US US26D x US26D Square Barrel Hinges Code 20 Hinges are handed, offered in special.77" weight only, and cannot be electrified. For options not offered in price book, contact factory. LH RH Hinge Type SQ333 Hinge 4 2" x 4 2" 4.30 mm x 4.30 mm Hinge Book B BE D 2.00 Square Barrel 3-Knuckle Hinges Code 20 Hinges are non-handed, offered in special.77" weight stainless steel only and cannot be electrified Hinge Type SQ34 Hinge 4 2" x 4" 4.30 mm x 0.60 mm 4 2" x 4 2" 4.30 mm x 4.30 mm For es: 0/0BE & BSP $26.90 Hinge Book 32D 2.00 Olive Knuckle Hinges Code 20 Hinges are handed, offered in standard weight only, and cannot be electrified. For options not offered in price book, contact factory. LH RH NL NL Hinge Type TA3383 Hinge 6" mm x mm Hinge Book NL B BE D 2.00 Canada: DH-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

65 s are effective September 0, 208 Listing: R2248 C US McKINNEY aluminum continuous hinges have been tested and certified by Underwriters Laboratories, Inc. (U.S.A. and Canada) for up to a 3-hour (A Label) Fire Listing for all 4'0" x 0'0" and 8'0"x 0'0" door LISTED and frame assemblies. Fire listing certification applies to all approved hollow metal and wood door assemblies in dry wall or masonry wall construction. No special preparations are required for up to 90 minutes. Fire Pins, which also increase the security of the door are required for 3-hour applications. Fire Pin applications fall within the UL guidelines for retrofitting assemblies in the field. Cutting the hinge in the field will not void the UL listing. Drilling locations for Fire Pins are found on each template. The most up to date templates are found on our web site at All models are approved for UL retrofit applications per NFPA 80. These hinges conform to ANSI / BHMA Standard A : Grade 2-50 (50 # cycles) Grade (300 # 500,000 cycles) Grade -300 (300 # cycles ) Grade -600 (600 # 500,000 cycles) McKinney Aluminum Continuous Geared Hinges Available Options: (Consult individual pages for availability of option with profile listed) Current Carrying Hinges: QC4 cable will carry 6 amps continuous at 24 volts in-rush for 820 milliseconds. When ordering, please specify where the modification is to be located from the top of the hinge down to the centerline of prep. Handing is required on all hinges provided with electrical modifications. Molex connectors with ElectroLynx are is warranted for 5 years. Molex connectors are included at each leaf for ease of electrical connection. electrical prep is supplied with a 80" cable lead. QC hinges are available with additional options, SER (Serviceable) and ACC (Accessible). MM Magnetic Monitoring Transfer also available with SER and ACC Options. QC ElectroLynx Connectors also available with SER (Serviceable) and ACC (Accessible) Options. EPT Power Transfer Prep (Cut Out Only) for Von Duprin. See page CH-0 for location template. This template must be filled out and included with your order. PT Power Transfer Prep (Cut Out Only) for Securitron, Yale, Centurion, Dorma or Adams Rite. Refer to page CH-0 for location template. This template must be filled out and included with your order. Custom Cut to Length (Hinges may be field cut and not void listing. Field-Cut hinges should be cut from bottom) Fire Pins Kit While hinges are rated without fire pins up to 90 minutes, 3-hour ratings require the use of fire pins. Fire pin kit consists of 4 each for inch hinges and 5 each for 96 to 20 inch hinges, as well as the installation instructions on what size holes to drill after the hinges have been installed. Hospital Type Tips are available on full mortise hinges Specify K pre-fix for Kawneer Tuffline Series Aluminum Doors on our MCK-2HD Series, order as K-MCK- 2HD and include size and finish Painted Colors Gear Cap Only - Batch charge and additional charge per hinge Complete Hinge - Batch charge and additional charge per hinge (minimum run 20 hinges) POA Lengths McKINNEY aluminum continuous geared hinges are listed and priced here in 79", 83", 85", 95" and 20" actual lengths for ease of installation on standard nominal door openings. The actual length of the hinge provides for head and threshold clearance. Custom lengths may be ordered as a special run. Consult the factory regarding minimum requirements and noncancellation policy on custom lengths. Hinges may be cut to appropriate length in the field. The hinge should be installed with the cut side on the bottom. Cutting in the field does not void the listing. We recommend that after removing cap, a saw blade be used to score and always begin cut at gear head. Never at leaves. Cut only from bottom of hinge. Do not cut through bearings or screw holes. Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CG-

66 s are effective September 0, 208 McKinney Aluminum Continuous Geared Hinges 2HD - 4HD - 25HD Option SN - Satin Nickel over CLEAR G - Gold Anodized Same as BRONZE BL - Black Anodized 20% over BRONZE QC-4* QC-8* QC-2* ACC-4* ACC-8* ACC-2* SER-4* SER-8* SER-2* MM* EPT Prep for Von Duprin 2.00 PT 2.00 HT* 2.00 Custom Cut to Length* FIREPIN-C4 (For 80"-95" hinge) FIREPIN-C5 (For 96"-20" hinge) Dutch Door Prep* Painted Colors P.O.A. For QC-2 order one of each of the above Fastener Kits (one kit required up to 95" 2 kits for 20") FMK-CL (7502) FMK-BZ (7503) Torx Screws 3.60 PBS250SP0R2 wood screw pack (2 ea per bag) CL $20.00 PBS250SP0BLR2 wood screw pack (2 ea per bag) BZ $20.00 TORX-PBS250SP0R2 CL TORX WS TORX-MS244SP0R2 CL TORX MS $36.00 Replacement SER Sections 2HD Option 9404 SER-4 CL Section SER-4 BZ Section SER-8 CL Section SER-8 BZ Section SER-2 CL Section SER-2 BZ Section HD - 54HD - 58HD Option SN - Satin Nickel over CLEAR G - Gold Anodized Same as BRONZE BL - Black Anodized 20% over BRONZE QC-4* QC-8* QC-2* HT* 2.00 Custom Cut to Length* FIREPIN-C4 (For 80"-95" hinge) FIREPIN-C5 (For 96"-20" hinge) Painted Colors P.O.A. For QC-2 order one of each of the above C Repl Cover 22HD CL D Repl Cover 22HD BZ C Repl Cover 54HD CL D Repl Cover 54HD BZ C293C Repl Cover 58HD Frame Side D293D Repl Cover 58HD Frame Side Specify length Door Side Option C-83 / D C-85 / D/ HD & 54HD Fastener Kits (one kit required up to 95" 2 kits for 20") Option FSHSK-CL (77350) FSHSK-BZ (7735) HD Option 58K-CL (77348) K-BZ (77349) FOR 22HD & 54HD Option TB420Z4 (4 pack) Thru-Bolt (Zinc) /4-20 X 5/8" $2.50 When ordering advise location for electrical options from top of hinge to center-line of electrical prep location. Handing is required for hinges with electrical prep. * Handing Required Refer to pages CH-0 for the appropriate power transfer locator template. This template must be filled out and included with your order. Gold or other custom finishes may have 6-8 week lead time. For -3/4 Plastic Laminate Doors request PBS250SP0 (#2 wood screw with #0 head, ½' long, available SS or BL $20.00 per pack of 2 Canada: CG-2 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

67 s are effective September 0, 208 FullMortiseEdgeHungFlushDoor MCK-2HD Heavy Duty Code 80 Product Product Product Product 79" 7676 CLEAR " 7674 BRONZE " 7677 CLEAR " BRONZE " 7678 CLEAR " BRONZE " 7679 CLEAR " BRONZE " CLEAR " BRONZE MCK-4HD Heavy Duty Code 80 Crtn Crtn Crtn Crtn Crtn K-MCK-2HD Code 80 For Kawneer Tuffline Series Aluminum Doors, pre-fix the MCK-2HD series with K, example 83" K-MCK-2HD CL 83" CLEAR Other sizes available same as MCK-2HD CL price. MCK-WTHD Heavy Duty Code 80 83" CLEAR " BRONZE " CLEAR " BRONZE " CL $ (WTCFM20HD) Not available BZ 79" 7675 CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE Crtn Crtn 8 Crtn 8 Full Mortise Edge Hung Inset Door MCK-22HD Heavy Duty Code 80 Product MCK-25HD Heavy Duty Code 80 Product Product MCK-28HD Heavy Duty Code 80 Available Options: 79" 7677 CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE Crtn Crtn Crtn Crtn 2 4 Complete installation hardware kit which includes 2-24 x 7 6" Phillips, Flat Head Undercut, Zinc screws for frame leaf, and thru bolts and shoulder screws for the door leaf are provided as standard pack unless otherwise specified. To order, specify length and finish. Hinges are supplied with # 2-24 x 7 6" Flat Head Undercut, Type C, thread-forming screws. Crtn 79" CLEAR " 7673 BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " 7670 CLEAR " BRONZE Crtn 83" CLEAR " BRONZE " 7692 CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE Option (Suffix) Net Add Custom Cut to Length* Fire Pin Kit: FIREPIN-C4 (For 80"-95" hinge) FIREPIN-C5 (For 96"-20" hinge) Painted Colors: Gear Cap Only Complete Hinge P.O.A P.O.A. * Requires Handing Fire Pins are required on 3 hour rated doors only. Full Mortise Safety Hinges MCK-35HD...Same Pricing as MCK-2HD MCK-38HD...Same Pricing as MCK-2HD McKinney Aluminum Continuous Geared Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CG-3

68 s are effective September 0, 208 McKinney Aluminum Continuous Geared Hinges Continuous Hinges Full Surface MCK-54HD Heavy Duty Code 80 79" 7676 CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE " CLEAR " BRONZE Crtn Crtn 0 4 MCK-58HD Heavy Duty Code 80 79" 768 CLEAR " 7682 BRONZE " 7683 CLEAR " 7684 BRONZE " 7685 CLEAR " 7686 BRONZE " 7687 CLEAR " 7688 BRONZE " 7689 CLEAR " BRONZE Crtn Crtn 2 4 Complete installation hardware kit which includes 2-24 x 7 6" selftapping, Phillips, Flat Head Undercut, Zinc screws for frame leaf, and thru bolts and shoulder screws for the door leaf are provided as standard pack unless otherwise specified. Complete installation hardware kit which includes 2-24 x 7 6" x #0 head, Thread-Forming, Flat Head Undercut screw for the frame leaf. Door leaf fasteners are 4"-20 shoulder bolts and thru bolts for 3 4" door. Available Options: Option (Suffix) Refer to Page CG-3 Canada: CG-4 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

69 s are effective September 0, 208 McKinney PT Information Form McKinney Aluminum Continuous Geared Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CG-5

70 s are effective September 0, 208 McKinney Stainless And Steel Continuous Hinges ing System & Standard Lengths Hinge Prefixes EG Edge Guard FM Edge Mount FS Full Surface HG Hinge/Guard HM Half Mortise HS Half Surface SC Swing Clear Hinge Series This series number indicates the type of hinge and base material used: MCK-3700 Carbon steel barrel hinges with stainless pin MCK-300 Stainless steel barrel hinges with stainless pin MCK Gauge stainless steel pin and barrel security hinges Hinge Models 00 Edge mount (formerly full mortise) 0 Full surface, 8" offset 02 Full surface, flush 03 Half surface, 8" offset 04 Half mortise, 8" offset 05 Edge mount hinge/guard 06 Half mortise hinge/guard 08 Edge guard 09 Full surface, swing clear 0 Swing clear hinge/guard Edge mount, self aligning 5 Edge mount, self aligning flush edge guard 2 Full surface inset, 3 4" offset 22 Edge mount hinge/guard, deep 23 Edge mount hinge/guard, deep, thru bolt 25 Edge mount swing clear 26 Edge mount hinge/guard, swing clear 27 Edge mount, safety hinge 29 Edge mount, self aligning Option Suffixes AS Adjust-A-Screws AMS Adjustable Monitoring Switch CTP Current Transfer Preparation EL ElectroLynx Current Transfer PoE Power Over Ethernet ETAP Electrical Transfer Access Prep *The MP-EMAP was changed to MP-ETAP. There is no prepping necessary for the MP-ETAP, although the frame and door need to be prepped for the EL2. EPT Electrical Power Transfer HT Hospital Tip LL Lead Lined PC Powder Coated RB Raised Barrel WT Wide Throw Standard Hinge Length Conversion Chart A 6'8" door opening = an actual length of " (handed) A 7'0" door opening = an actual length of 83 8" A 7'2" door opening = an actual length of 85 8" (handed) A 8'0" door opening = an actual length of 95" A 0'0" door opening = an actual length of 8 3 4" Custom hinge length will be evaluated at the time of request to ensure proper pin to knuckle alignment. Some custom length requests may be adjusted to ensure a proper hinge assembly. Specify handing on all custom hinge lengths Standard Powder Coat es POA BHMA # Nearest McKINNEY Description Equivalent 690 MP-PC- Dark Bronze 74 MP-PC-2 Eggshell White 693 MP-PC-3 Semi Gloss Black 689 MP-PC-4 Aluminum 706 MP-PC-5 Sun Gold 69 MP-PC-6 Light Bronze For FM300 Series Only POA 605 MP-PC-7 Polished Brass Kynar Paint with Color Approval - POA Adjust-A-Screws for MCK-HG-305; HG-30; HG-322; HG-323; HG326 7' Requires 2 8' Reguires 23 $2.40 ea. 0' Requires 27 Canada: CH- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

71 s are effective September 0, 208 Continuous Hinge Modifications Cut to Charge ADDITIONAL PRICE Please specify handing on all custom hinge lengths. For hinges 40" to 83 8" in length to 7'0" price For hinges " to 95" in length to 8'0" price For hinges 95 6" to 8 3 4" in length to 0'0" price For hinges 8 3 6" to 92" in length POA Handing Required PRODUCT SUFFIX ADDITIONAL PRICE Hospital Tip -HT /hinge Available on all models except springloaded toilet partition hinges. Helps provide a safe, clean environment. Handing Required PRODUCT SUFFIX ADDITIONAL PRICE Available on all edge mount and half surface models except on Aluminum hinges. PRODUCT SUFFIX ADDITIONAL PRICE Lead Lined Cover -LL /cover Lead lined astragal for EGT+85.95/astragal Only available on surface mounted Hinges. Used for x-ray room doors and other locations where radiation leakage could be a problem. McKinney Stainless And Steel Continuous Hinges PRODUCT SUFFIX ADDITIONAL PRICE Wide Throw -WT POA Only available on 300 series hinges. Specify distance from pin centerline to heel edge of hinge when ordering. Reinforcement may be required on extreme wide throw applications. These conditions will be determined through a drawing approval process. Cost will be determined at time of approval. Custom Angle: per angle Automatic Door Bottom Cut Weld End Pins PRODUCT ADDITIONAL PRICE Security Studs /hinge up to 85" /hinge over 85" Stainless steel security studs mounted to the frame leaf. Door leaf is drilled to accommodate studs Three studs installed on hinges up to 85" Four studs installed on hinges over 85" Door and frame must be specially prepared to accommodate security studs. PRODUCT ADDITIONAL PRICE Raised Barrel (Swaged) For cased open or center pivot doors. Available on all edge mount and half surface models. Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CH-2

72 s are effective September 0, 208 McKinney Stainless And Steel Continuous Hinges Continuous Hinge & Edge Guard Modifications PRODUCT EL Concealed Circuit ADDITIONAL PRICE For 300, 3500, and 3700 series Edge mount only. Not available on Raised Barrel applications. ElectroLynx EL EL EL POE Power over Ethernet +, PRODUCT ADDITIONAL PRICE Electrical Modification Access Prep (formerly ETAP) PRODUCT ADDITIONAL PRICE PT or EPT Power Transfer Prep (formerly CPT) Centerline of hinge is standard location by submitting the Power Transfer Template located on page Ch-0. Please provide location and handing forall locations. For swing clear models /hinge For all other models /hinge PRODUCT ADDITIONAL PRICE AMS Adjustable Monitoring Switch PRODUCT PoE Power Over Ethernet Cutout prep for the AMS & EL. Modifications that allows easy one person access to wiring between the hinge and door/frame. MP-EMAP /per ADDITIONAL PRICE Rigid welded assembly gives you the ability to adjust your monitoring switch to work with all applications. Not available on aluminum hinges or powder coat finishes /hinge prep charge (see MP-EMAP) For 300, 3500 and 3700 series edge mount only. With ElectroLynx connectors (9 wire) and Electrical Transfer Access Prep (ETAP). PoE Power over Ethernet +, Standard Stainless Stell Screw Pack (See following pages for additional Screw Packs) Standard Screw Pack for FM300; HG305; HG3; HG35 - KMPSS 6.00 Standard Screw Pack for FM3500; FS350; FS3502; HG MS244SP0SS24 Standard Screw Pack for FS30; FS302 - M Standard Screw Pack for HS303; HM304; HG306 - M , TKS267SP0SS Security Fastener USE -TKS-MS244SP0SS Canada: CH-3 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

73 s are effective September 0, 208 Fastener / Screw Pack Information Product Description Properties 2-24 x /6 x #0 Head, Flat Head Undercut Self-Drilling Screw TKS267SP0SS24 (24 Pack) Stainless Steel $0.50 TKS267SP0BL24 MP-2 (24 Pack) Black Zinc $2.50 #8 x 3/4" Flat Head Self-Drilling Screw McKinney Stainless And Steel Continuous Hinges S323-08R2-603 S323-08R2-663 TORX-TKS8075Z For attaching 00, 200, and 300 series covers (Per each) For attaching 00, 200, and 300 series covers (Per each) For attaching 00, 200, and 300 series covers (Per each) Zinc Phillips $ 0.50 Black $ 0.50 ZincTorx $.40 PBS250SP0SS24 PBS250SP0BLR2 T25PBS250SPSS x -/2 x #0 Head, icle Board Screw For edge mounting to wood (24 Pack) For edge mounting to wood (24 Pack) For edge mounting to wood. Security Pin. (24 Pack) Stainless Steel $7.50 Black $9.50 Stainless Steel Torx $2.70 M /8" Adjust-A-Screw With 0-32 InternalThread and Hex Head Adjustment Right Hand used with MS0075SS screw (Per each) Note: 5/6" pilot hole required for 3/8" - 6 tap 2 ga. reinforcement required $ x 3/4" Flat Head Machine Screw See note on CH for quantities required. MS0075SS Used with M Adjust-A-Screw (Per each) Stainless Steel Phillips $ 0.60 TORX-MS0075SS Used with M Adjust-A-Screw (Per each) Stainless Steel Torx $.50 MS0075BL Used with M Adjust-A-Screw (Per each) Black Stainless Steel $ 0.80 Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CH-4

74 s are effective September 0, 208 McKinney Stainless And Steel Continuous Hinges Fastener / Screw Pack Information Product Description Properties 2-24 x 7/6 x #0 Head, Flat Head Undercut Machine Screw, with Security Pin, Tri-Round Threads TORX-MS244SP0SS24 For edge mounting to metal (24 Pack) Stainless SteelTorx $2.70 TORX-MS244SP0BL24 (24 Pack) Black Stainless Steel Torx $ /6 x -/4 Phillips Flat Head Concrete Screw TC3625 (Per each) Zinc $.04 TB420Z4 /4-20 x -5/8" Thru-bolt For surface mounting to wood (4 pack) Zinc Steel $ TB420SS For surface mounting to wood (Per each) Stainless Steel $ 6.70 TB420BL4 For surface mounting to wood (4 Pack) Black $ 6.70 TB38Z /4-20 x -/4" Thru-bolt For surface mounting to wood (Per each) Zinc $.70 8 SJN /4-20 Molly Jack Nut M /6" hole (Per each) Zinc $ 3.50 #4 x 3/4"T-27Torx Button Head Sheet Metal Screw S32C4T2-630 (Per each) Stainless $ 3.20 S S222-46R6-603 TORX-MS400Z /4-4 x 3/4" Pan Head Self-Drilling Screw For surface mounting to metal (Per each) /4-20 x " Pan Head Machine Screw For surface mounting to metal (Per each) For surface mounting to metal (Per each) ZincTorx $ 3.20 Zinc Phillips $.50 ZincTorx $ 2.00 Canada: CH-5 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

75 s are effective September 0, 208 Stainless Steel Edge Mount Hinge MCK-FM300 Code 83 Door Door Length Length Hand Hand 6'8" " D '8" " '0" 83 8" D '0" 83 8" '2" 85 8" D '2" 85 8" '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. Carton Qty Wgt Stainless Steel Edge Mount Full- Wrap - Edge Guard MCK-HG305 Code 83 6'8" " RH 32D '8" " 7704 LH 32D '8" " 7686 RH '8" " 7705 LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" 7706 LH 32D '2" 85 8" RH '2" 85 8" 7707 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. 6'8" " RH 32D '8" " 7708 LH 32D '8" " 7687 RH '8" " 7709 LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" 770 LH 32D '2" 85 8" RH '2" 85 8" 77 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Carton Qty Wgt Stainless Steel Edge Mount Half- Wrap - Edge Guard MCK-HG35 Code 83 Door Length Hand Refer to Pages CH- thru CH-3 For Available Options. Carton Qty Wgt Stainless Steel Edge Mount Full- Wrap Edge Guard MCK-HG322 Code 83 Door Length Hand Refer to Pages CH- thru CH-3 For Available Options. 6'8" " 772 RH 32D '8" " 773 LH 32D '8" " 774 RH '8" " 775 LH '0" 83 8" D '0" 83 8" '2" 85 8" 778 RH 32D '2" 85 8" 779 LH 32D '2" 85 8" 7720 RH '2" 85 8" 772 LH '0" 95" D '0" 95" '0" 8 3 4" D, '0" 8 3 4" ,8.36 6'8" " 7726 RH 32D '8" " 7727 LH 32D '8" " 7728 RH '8" " 7729 LH '0" 83 8" D '0" 83 8" '2" 85 8" 7732 RH 32D '2" 85 8" 7733 LH 32D '2" 85 8" 7734 RH '2" 85 8" 7735 LH '0" 95" D '0" 95" '0" 8 3 4" D, '0" 8 3 4" ,8.36 Carton Qty Wgt Stainless Steel Edge Mount Full- Wrap Edge Guard MCK-HG323 Code 83 Door Length Hand 6'8" " 7740 RH 32D '8" " 774 LH 32D '8" " 7742 RH '8" " 7743 LH '0" 83 8" D '0" 83 8" '2" 85 8" 7746 RH 32D '2" 85 8" 7747 LH 32D '2" 85 8" 7748 RH '2" 85 8" 7749 LH '0" 95" D '0" 95" '0" 8 3 4" D, '0" 8 3 4" , Carton Qty Wgt Refer to Pages CH- thru CH-3 For Available Options. Stainless Steel Swing Clear Full- Wrap Edge Guard MCK-HG326 Code 83 Door Length Hand Carton Qty Wgt McKinney Stainless And Steel Continuous Hinges Refer to Pages CH- thru CH-3 For Available Options. Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CH-6

76 s are effective September 0, 208 McKinney Stainless And Steel Continuous Hinges Stainless Steel Edge Mount Safety Hinge MCK-FM327 Code 83 Door Length Hand 6'8" " 7754 RH 32D '8" " 7755 LH 32D '8" " 7756 RH '8" " 7757 LH '0" 83 8" D '0" 83 8" '2" 85 8" 7760 RH 32D '2" 85 8" 776 LH 32D '2" 85 8" 7762 RH '2" 85 8" 7763 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. Stainless Steel Half Mortise Hinge MCK-HM304 Code 83 Door Length Hand '0" 83 8" D '0" 83 8" '2" 85 8" 7768 RH 32D '2" 85 8" 7769 LH 32D '2" 85 8" 7770 RH '2" 85 8" 777 LH '0" 95" D '0" 95" '0" 8 3 4" D Refer to Pages CH- thru CH-3 For Available Options. Door Length Hand 7'0" 83 8" D '0" 83 8" '2" 85 8" 7774 RH 32D '2" 85 8" 7775 LH 32D '2" 85 8" 7776 RH '2" 85 8" 7777 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. Carton Qty Wgt Carton Qty Wgt Stainless Steel Half Mortise, Half- Wrap - Edge Guard MCK-HG306 Code 83 Carton Qty Wgt Stainless Steel Swing Clear Half- Wrap - Edge Guard MCK-HG3 Code 83 Door Length Hand 7'0" 83 8" D '0" 83 8" '2" 85 8" 7780 RH 32D '2" 85 8" 778 LH 32D '2" 85 8" 7782 RH '2" 85 8" 7783 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. Stainless Steel Full Surface 8" Inset Hinge MCK-FS30 Code 83 Door Length Hand 6'8" " 7786 RH 32D '8" " 7787 LH 32D '8" " 7788 RH '8" " 7789 LH '0" 83 8" D '0" 83 8" '2" 85 8" 7792 RH 32D '2" 85 8" 7793 LH 32D '2" 85 8" 7794 RH '2" 85 8" 7795 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Refer to Pages CH- thru CH-3 For Available Options. Stainless Steel Half Surface Hinge MCK-HS303 Code 83 Door Length Hand Carton Qty Wgt Carton Qty Wgt '8" " D '0" 83 8" D '2" 85 8" D '0" 95" D '0" 8 3 4" D Refer to Pages CH- thru CH-3 For Available Options. Carton Qty Wgt Canada: CH-7 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

77 s are effective September 0, 208 Stainless Steel Full Surface Flush Mount Hinge MCK-FS302 Code 83 Door Door Length Length Hand Refer to Pages CH- thru CH-3 For Available Options. Stainless Steel Full Surface Swing Clear Hinge MCK-FS309 Code 83 Hand Refer to Pages CH- thru CH-3 For Available Options. 6'8" " D '8" " '0" 83 8" D '0" 83 8" '2" 85 8" D '2" 85 8" '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" '8" " RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" 7722 RH 32D '2" 85 8" 7723 LH 32D '2" 85 8" 7724 RH '2" 85 8" 7725 LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Stainless Steel Full Surface 3 4" Offset Hinge MCK-FS32 Code 83 Door Length Hand 6'8" " RH 32D '8" " 7722 LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" LH 32D '2" 85 8" RH '2" 85 8" LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" , Refer to Pages CH- thru CH-3 For Available Options. Carton Qty Wgt Carton Qty Wgt Carton Qty Wgt Stainless Steel Swing Clear Full- Wrap Edge Guard MCK-HG30 Code 83 Refer to Pages CH- thru CH-3 For Available Options. Door Length Hand 6'8" " RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" 7724 LH 32D '2" 85 8" RH '2" 85 8" LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" , Carton Qty Wgt 3500 Series Stainless Security Hinges Stainless Steel Heavy Duty Edge Mount Hinge MCK-FM3500 Code 83 Refer to Pages CH- thru CH-3 For Available Options. Door Length Hand 6'8" " RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" LH 32D '2" 85 8" 7727 RH '2" 85 8" LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" Stainless Steel Heavy Duty Full Surface 8" Inset Hinge MCK-FS350 Code 83 Refer to Pages CH- thru CH-3 For Available Options. Door Length Hand 6'8" " RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" LH 32D '2" 85 8" RH '2" 85 8" LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" , Carton Quantity Carton Quantity McKinney Stainless And Steel Continuous Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CH-8

78 s are effective September 0, 208 McKinney Stainless And Steel Continuous Hinges Stainless Steel Heavy Duty Full Surface Hinge MCK-FS3502 Code 83 Door Length Hand 6'8" " 7729 RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" D '0" 83 8" '2" 85 8" RH 32D '2" 85 8" LH 32D '2" 85 8" RH '2" 85 8" LH '0" 95" D '0" 95" '0" 8 3 4" D '0" 8 3 4" , Refer to Pages CH- thru CH-3 For Available Options Series Stainless Security Hinges (Continued) Carton Quantity Stainless Steel Heavy Duty Full Wrap Edge Guard MCK-HG3505 Code 83 Door Length Hand 6'8" " RH 32D '8" " LH 32D '8" " RH '8" " LH '0" 83 8" RH 32D '0" 83 8" 7730 RH '2" 85 8" 773 RH 32D '2" 85 8" 7732 LH 32D '2" 85 8" 7733 RH '2" 85 8" 7734 LH '0" 95" 7735 RH 32D '0" 95" 7736 RH '0" 8 3 4" 7737 RH 32D '0" 8 3 4" 7738 RH 32, Refer to Pages CH- thru CH-3 For Available Options. Carton Quantity Steel Full Mortise Hinge MCK-FM3700 Code 87 Door Length Hand Steel Hinges Carton Qty Wgt SteelFullSurfaceFlushMountHinge MCK-FM3702 Code 87 Door Length Hand Carton Qty Wgt 6'8" " RH Zinc '8" " LH Zinc '0" 83 8" 7695 Zinc '2" 85 8" RH Zinc '2" 85 8" LH Zinc '0" 95" Zinc '8" " RH Zinc '8" " LH Zinc '0" 83 8" 7698 Zinc '2" 85 8" RH Zinc '2" 85 8" LH Zinc '0" 95" Zinc Refer to Pages CH- thru CH-3 For Available Options. Steel Full Surface 8" Inset Hinge MCK-FS370 Code 87 Door Length Hand Carton Qty Wgt Refer to Pages CH- thru CH-3 For Available Options. Steel Half Surface Hinge MCK-HS3703 Code 87 Door Length Hand Carton Qty Wgt 6'8" " RH Zinc '8" " 7725 LH Zinc '0" 83 8" Zinc '2" 85 8" RH Zinc '2" 85 8" LH Zinc '0" 95" Zinc '8" " 7739 RH Zinc '8" " LH Zinc '0" 83 8" Zinc '2" 85 8" 7732 RH Zinc '2" 85 8" 7726 LH Zinc '0" 95" Zinc Refer to Pages CH- thru CH-3 For Available Options. Refer to Pages CH- thru CH-3 For Available Options. Canada: CH-9 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

79 s are effective September 0, 208 McKinney Current Transfer Prep (CTP) Information Form McKinney Stainless And Steel Continuous Hinges Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in CH-0

80 s are effective September 0, 208 McKinney Screw Packs McKinney Screw Packs Sales Code: 5, Stock Pol: O # Description Inv Type # Description Inv Type MK22590P /2 X 2 PHWS 26D SOLID FG $0.80 MK22594 /2 X 2 PHWS SOL 0 PER C MS $0.80 MK2258 /2 X 2 PHWS SOL 0B MS $0.80 MK22590 /2 X 2 PHWS SOL 26D MS $0.80 MK22597 /2 X 2 PHWS SOL PC MS $0.80 MK22484 /4 X 2 PHWS 0B SOL PER C MS $0.80 MK22480P /4 X 2 PHWS 26 SOLID FG $0.80 MK2248P /4 X 2 PHWS 26D SOLID FG $0.80 MK22483 /4 X 2 PHWS SOL 0 PER C MS $0.80 MK22480 /4 X 2 PHWS SOL 26 PER C MS $0.80 MK22470 /4 X 2 PHWS SOL 3 MS $0.80 MK22487 /4 X 2 PHWS SOL AP FG $0.80 MK22475 /4 X 2 PHWS SOL PC MS $0.80 MK22390 /4 X 2 FL PH SS WS 32D MS $0.80 MK22476 /4X2 PHWS SOL 4 PER C MS $0.80 MK22449 X 0 FH PHWS SOLID P MS $0.80 MK22450 X 0 FHPHWS SOLID 26 MS $0.80 MK22452 X 0 FHPHWS SOLID 26D MS $0.80 MK2245 X 0 FHPHWS SOLID 32D MS $0.80 MK2369 X 0 PHWS 0B SOLID MS $0.80 MK22682 /2 X 0 24PHMS SOL 0 PER C FG $0.60 MK2237 /2 X 2 24PHMS 32D PER C MS $0.60 MK22709 /2 X 2 24PHMS SOL 0 PER C MS $0.60 MK22706 /2 X 2 24PHMS SOL 26 PER C MS $0.60 MK22706P /2 X 2-24 PHMS 26 SOLID FG $0.60 MK22707P /2 X 2-24 PHMS 26D SOLID FG $0.60 MK2270 /2 X 2-24 PHMS SOL 0B MS $0.60 MK22703 /2 X 2-24 PHMS SOL 3 MS $0.60 MK22702 /2 X 2-24 PHMS SOL 4 MS $0.60 MK2274 /2 X 2-24 PHMS SOL AP FG $0.60 MK2270 /2 X 2-24 PHMS SOL PC MS $0.60 MK22707 /2 X 2 24PHMS BR 26D PER C MS $0.60 MK2988P /2 X 2 PHWS 26D FG $0.40 MK2989 /2 X 2 PHWS STEEL 0 PER C MS $0.40 MK2678 /2 X 2 PHWS STEEL P PER C MS $0.40 MK2988 /2 X 2 PHWS STL 26D PER C MS $0.40 MK2994 /2X 2 PHWS 0B STL MS $0.40 MK242 /4 X 0 PHWS STL 0 PER C FG $0.40 MK2473 /4 X 2 PHWS 0B STL PER C MS $0.40 MK2469P /4 X 2 PHWS 26 FG $0.40 MK2475 /4 X 2 PHWS 2C STL MS $0.40 MK2466P /4 X 2 PHWS 3 MS $0.40 MK2465P /4 X 2 PHWS 4 MS $0.40 MK2248 /4 X 2 PHWS BR 26D PER C MS $0.40 MK2660 /4 X 2 PHWS D3 STL MS $0.40 MK2659 /4 X 2 PHWS D4 STL MS $0.40 MK2464P /4 X 2 PHWS P FG $0.40 MK2469 /4 X 2 PHWS STEEL 26 PER C MS $0.40 MK22009 /4 X 2 PHWS STL 0A MS $0.40 MK2470 /4 X 2 PHWS STL 26D PER C MS $0.40 MK2466 /4 X 2 PHWS STL 3 PER C MS $0.40 MK2478 /4 X 2 PHWS STL AP PER C MS $0.40 MK2680 /4 X 2 PHWS STL D2 MS $0.40 MK2405 /4X0 0 PHWS STL 4 PER C MS $0.40 MK240 /4X0 0PHWS STL 26D PER C FG $0.40 MK2472 /4X2 PHWS STL 0 PER C MS $0.40 MK2465 /4X2 PHWS STL 4 MS $0.40 MK2363 X 0 PHWS 0B STL PER C MS $0.40 MK2359P X 0 PHWS 26 FG $0.40 MK2360P X 0 PHWS 26D FG $0.40 MK2365 X 0 PHWS 2C STL MS $0.40 MK2359ZB X 0 PHWS 2C-BRIGHT FG $0.40 MK2354 X 0 PHWS P STL PER C MS $0.40 MK2362 X 0 PHWS STEEL 0 PER C MS $0.40 MK2355 X 0 PHWS STEEL 4 PER C MS $0.40 MK2368 X 0 PHWS STEEL AP PER C MS $0.40 MK22008 X 0 PHWS STL 0A MS $0.40 MK2359 X 0 PHWS STL 26 PER C MS $0.40 MK2360 X 0 PHWS STL 26D PER C MS $0.40 MK2356 X 0 PHWS STL 3 PER C MS $0.40 MK2200 X 0 PHWS STL D FG $0.40 MK220 X 0 PHWS STL D2 MS $0.40 MK2202 X 0 PHWS STL D3 MS $0.40 MK2203 X 0 PHWS STL D4 MS $0.40 MK2328 X 9 PHWS STEEL 0 PER C FG $0.40 MK232 X 9 PHWS STEEL 4 PER C FG $0.40 MK /4X6 PHWS STEEL 0 PER C FG $0.40 MK2728 /2 X 0 24PHMS STEEL 4 PER C MS $0.30 MK274 /2 X 0 24PHMS STEEL AP PER C MS $0.30 MK2727 /2 X 0 24PHMS STEEL P PER C MS $0.30 MK2736 /2 X 0 24PHMS STL 0B PER C MS $0.30 MK2729 /2 X 0 24PHMS STL 3 PER C MS $0.30 MK2732P /2 X 0-24 PHMS 26 FG $0.30 MK2732 /2 X 0-24 PHMS 26 STL MS $0.30 MK2733P /2 X 0-24 PHMS 26D MS $0.30 MK2738 /2 X 0-24 PHMS 2C STL MS $0.30 MK22380 /2 X 0-24 PHMS 32D MS $0.30 MK2222 /2 X 0-24 PHMS D3 STL MS $0.30 MK2228 /2 X 0-24 PHMS D4 STL FG $0.30 MK22297 /2 X 2 24PHMS STEEL 26 PER C MS $0.30 MK22388 /2 X 2 24PHMS STEEL AP PER C MS $0.30 MK22386 /2 X 2 24PHMS STEEL P PER C MS $0.30 MK2766 /2 X 2 24PHMS STL 0B PER C MS $0.30 MK22298 /2 X 2 24PHMS STL 26D PER C MS $0.30 MK2759 /2 X 2 24PHMS STL 3 PER C MS $0.30 MK22300P /2 X 2-24 PHMS 0 FG $0.30 MK2207P /2 X 2-24 PHMS 0A FG $0.30 MK2207 /2 X 2-24 PHMS 0A STL MS $0.30 MK2766P /2 X 2-24 PHMS 0B FG $0.30 MK22297P /2 X 2-24 PHMS 26 FG $0.30 MK2768 /2 X 2-24 PHMS 2C STL MS $0.30 MK2759P /2 X 2-24 PHMS 3 MS $0.30 MK2968 /2 X 2-24 PHMS D4 STL MS $0.30 MK2758 /2 X 2-24PHMS STL 4 MS $0.30 MK X /2 FL TX SS WS 32D MS $.20 MK X /4 FL TX SS WS 32D MS $.20 MK22209 STS TORX BAGS /2X2-24 $.48 MK22200 /4-20 X 5/8 FL TX SS MSCR FG $.50 MK22203 /4-20 X/2 FL TX ST MS 26D MS $.50 MK2296 /4-20 X /2 FL TX ST MS P FG $.50 MK X /2 FL TX ST WS 26D MS $0.94 MK X /2 FL TX ST WS P MS $0.94 MK X /4 FL TX ST WS 26D MS $0.94 MK229 2 X /4 FL TX ST WS P FG $0.94 MK X 24 X /2 FL TX ST MS P MS $0.94 MK X /2 FL TX ST MS 26D MS $0.94 MK2229 4X /2 FL,PH,ST,TSCR,0B MS $.00 MK X/2 TORX SC FOR CSS-9 MS $.50 MK X /4-20 O.H.P.H.M.S. 0 STL MS $.50 MK X /4-20 O.H.P.H.M.S. 0B ST MS $.50 MK X /4-20 O.H.P.H.M.S. 26D ST MS $.50 MK283 2 X /4-20 O.H.P.H.M.S. AP STL MS $.50 MK287 2 X /4-20 O.H.P.H.M.S. PC STL MS $.50 MK2823P 2 X /4-20 OHPHMS 26D FG $.50 Canada: SPK- Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

81 s are effective September 0, 208 McKinney Complete Screw Packs Sales Code: 5, For Full Moritse Hinges, SS = Stainless, STL = Steel # Description Inv Type # Description Inv Type McKinney Screw Packs MK /2 SS USP SCREW PACK PR $9.60 MK /2 STL 0B SCREW PACK PR $2.80 MK /2 STL 0 SCREW PACK PR $9.60 MK /2 SS 0B SCREW PACK PR $2.80 MK /2 STL USP SCREW PACK PR $9.60 MK /2 STL 26D SCREW PACK PR $9.60 MK /2 STL 0BE SCREW PACK PR $9.60 MK /2 STL US3 SCREW PACK PR $2.80 MK /2 STL US4 SCREW PACK PR $9.60 MK /2 STL 5 SCREW PACK PR $9.60 MK /2 STL 26 SCREW PACK PR $2.80 MK /2 STL D3 SCREW PACK PR $9.60 MK /2 STL D4 SCREW PACK PR $9.60 MK /2 STL TA D SCREW PACK PR $2.00 MK /2 SS US3 SCREW PACK PR $2.80 MK /2 SS US4 SCREW PACK PR $9.60 MK /2 SS 0 SCREW PACK PR $9.60 MK /2 SS 26 SCREW PACK PR $2.80 MK /2 SS D3 SCREW PACK PR $9.60 MK /2 SS D4 SCREW PACK PR $9.60 MK /2 SS 32D SCREW PACK PR $2.80 Continuous Gear Screw Packs for 2HD - 4HD - 25HD Sales Code: 80X # Description Inv Type MK7502 FMK-CL (FULL MORT SCR PACK)CL PR $34.00 MK7503 FKM-BZ (FULL MORT SCR PACK) BZ PR $34.00 Screw Packs for 22HD - 54HD Sales Code: 80X # Description Inv Type MK77350 FSHSK-CL (FS/HS SCREW PACK) CL PR $34.00 MK7735 FSHKS-BZ(FS/ HS SCREW PACK) BZ PR $34.00 Screw Packs for 58HD Sales Code: 80X # Description Inv Type MK7502 FMK-CL (FULL MORT SCR PACK)CL PR $34.00 MK7503 FKM-BZ (FULL MORT SCR PACK) BZ PR $34.00 Stainless Pin & Barrel Standard Screw Packs Sales Code: 80X # Description Inv Type KMPSS Screw Pack for FM300; HG305; HG3; HG35 PR $34.00 MS244SP0SS24 Screw Pack for FM3500; FS350; FS3502; HG3505 PR M Screw Pack for FS30; FS302; HS303; HM304; HG306 PR $34.00 Includes 2 TKS267SP0SS23; 6 M ; 6 TORX-TKS4075R Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in SPK-2

82 s are effective September 0, 208 Notes: Canada: SPK-3 Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in

83 s are effective September 0, 208 Notes: McKinney Screw Packs Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in SPK-4

84 McKinney Products Company ASSA ABLOY Door Security Solutions Canada 60 Four Valley Drive, Vaughan, ON L4K 4T9 Phone: (800) Fax: (800) Canada: Copyright , ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited /208