Mulicolor conras sensor Dimensioned drawing en 01-2016/06 50133231 12-30 V DC 15 khz 13mm We reserve he righ o make changes DS 2_en_50133231.fm Easy o adjus hrough display of he signal srengh on he device Simple sensiiviy adjusmen wih muliurn poeniomeer RGB ransmier wih selecable deecion color Removable roary operaing knob enables comforable, ool-free adjusmen Maximum packing qualiy hrough shor response ime Remoe conrol via conrol cable Blocking of all operaional conrols via conrol cable Analog oupu for signal evaluaions in he conrol U L US C LISTED IEC 60947... IEC 60947... Accessories: (available separaely) IP 69K IP 67 Mouning sysems (BTU 200M, BT 95) Mouning adaper for sandard design (80 mm x 53 mm x 30 mm) BTX 018M Cable wih M12 connecor (K-D M12 ) A B C D E F G Indicaor diodes Knurled knob for sensiiviy adjusmen (removable) Display of he special funcions Opical axis Horizonal ligh spo orienaion (ransverse) Ligh spo orienaion verical (lenghwise) Toggle swich for deecion color Elecrical connecion 12-30 V + OUT 2 GND OUT 1 IN BR / BN WS / WH BL / BU SW/ BK GR / GY Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 info@leuze.com www.leuze.com. 2-01
Technical daa Opical daa Scanning range Ligh source 1) Ligh spo dimensions Ligh spo orienaion Timing Swiching frequency Response ime 13mm ± 3mm LEDs (red, green, blue) 1mm x 4mm (a a disance of 13 mm) verical (lenghwise) or horizonal (ransverse) swiching oupus: 15kHz swiching oupus: 33μs analog oupu: 100μs < 300ms Readiness delay Elecrical daa Operaing volage U 2) B 12 30VDC (incl. residual ripple) Residual ripple 15% of U B Open-circui curren 25mA (a 24V) Swiching oupus/funcions OUT1 push-pull, PNP dark swiching (dark on), NPN ligh swiching (ligh on), changeover-capable Only KRT18B /G6T : OUT2 push-pull, PNP ligh swiching (ligh on), NPN dark swiching (dark on), changeover-capable Signal volage high/low (U B -2V)/ 2V Oupu curren max. 100mA Inpu IN configuraion inpu and blocking of he operaional conrols Analog oupu OUT2 middle posiion of analog range for whie arge (90% rem.) KRT18B /GCT : KRT18B /GC1T : KRT18B /GV1T : curren: 4 20mA, R L 500Ohm curren: 0.3 10mA, R L 500Ohm volage: 0 5V, R L 2kOhm Indicaors Green LED coninuous ligh ready Yellow LED coninuous ligh swiching signal - dark swiching (dark on) Bar graph recepion signal srengh, 13-level Yellow LEDs - special funcions ligh/dark swiching Mechanical daa Housing diecas zinc, chemically nickel-plaed Connecor diecas zinc, chemically nickel-plaed Opics PMMA Operaion muliurn poeniomeer for sensiiviy adjusmen, buon for changing he deecion color (C) Weigh 60g Connecion ype M12 connecor, 5-pin Environmenal daa Ambien emp. (operaion/sorage) -40 C +60 C/-40 C +70 C Proecive circui 3) 2, 3 VDE safey class 4) III Degree of proecion IP67, IP 69K Ligh source exemp group (in acc. wih EN 62471) Sandards applied IEC 60947-5-2 Cerificaions UL 508, C22.2 No.14-13 2) 5) Chemical resisance esed in accordance wih ECOLAB Addiional funcions Full conrol of he applicaion 13-level bar graph signal display on he device Ligh/dark swiching (L/D) can be acivaed via conrol buon Change of deecion color can be acivaed via conrol buon 1) Average life expecancy 100,000h a an ambien emperaure of 25 C 2) For UL applicaions: use is permied exclusively in Class 2 circuis according o NEC 3) 2=polariy reversal proecion, 3=shor circui proecion for all ransisor oupus 4) Raing volage 50V 5) These proximiy swiches shall be used wih UL Lised Cable assemblies raed 30V, 0.24A min, in he field insallaion, or equivalen (caegories: CYJV/CYJV7 or PVVA/PVVA7) Noes Observe inended use! This produc is no a safey sensor and is no inended as personnel proecion. The produc may only be pu ino operaion by compeen persons. Only use he produc in accordance wih is inended use. Glossy objecs: Wih glossy objecs, he sensor is o be fasened a an inclinaion of approx. 10 15 relaive o he objec surface. Alignmen aid: An alignmen aid is included in he scope of delivery of each sensor. This faciliaes simple alignmen of he sensor o he working disance of 13 mm wihou needing o perform elecrical commissioning. 13 mm 13 mm 10 15. 2-01 2016/06
Mulicolor conras sensor Par number code K R T 1 8 B M. H 2 / G 6 T - M 1 2 Operaing principle KRT Conras sensor Series 18B 18B series Ligh source M Mulicolor RGB Ligh spo orienaion H Horizonal (ransverse) V Verical (lenghwise) Seing 2 Muliurn poeniomeer wih bar graph signal display, RGB changeover via buon Pin assignmen of connecor pin 4 / black cable wire (OUT1) G Push-pull swiching oupu, PNP dark swiching (dark on), NPN ligh swiching (ligh on) Pin assignmen of connecor pin 2 / whie cable wire (OUT2) 6 Push-pull swiching oupu, PNP ligh swiching (ligh on), NPN dark swiching (dark on) C Analog curren oupu 4 20mA C1 Analog curren oupu 0.3 10mA V1 Analog volage oupu 0 5V Pin assignmen of connecor pin 5 / gray cable wire (IN) T Inpu for changing he deecion color, ligh/dark swiching and locking of he operaional conrols Connecion echnology M12 M12 connecor, 5-pin Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0. 2-01 info@leuze.com www.leuze.com
Order guide The sensors lised here are preferred ypes; curren informaion a www.leuze.com Order code Par no. Feaures.V2/G6T-M12 50131246.H2/G6T-M12 50131247.V2/GCT-M12 50132572.H2/GCT-M12 50132612.V2/GC1T-M12 50132613.V2/GV1T-M12 50132614 Accessories Ligh spo orienaion verical (lenghwise), anivalen push-pull oupus Ligh spo orienaion horizonal (ransverse), anivalen push-pull oupus Ligh spo orienaion verical (lenghwise), analog oupu (4 20mA) Ligh spo orienaion horizonal (ransverse), analog oupu (4 20mA) Ligh spo orienaion verical (lenghwise), analog oupu (0.3 10mA) Ligh spo orienaion verical (lenghwise), analog oupu (0 5mA) BTX 018M 50133412 Mouning adaper for mouning on mouning devices for sensors in he sandard design (80 mm x 53 mm x 30 mm) Mouning adaper BTX 018M Wih he help of mouning adaper BTX 018M (par no. 50133412), conras sensors KRT18B can be mouned on exising mouning devices for conras sensors in he sandard design (80mm x 53mm x 30mm).. 2-01 2016/06
Mulicolor conras sensor Adjusing he swiching hreshold The sensiiviy of conras sensor KRT18B is se via he muliurn poeniomeer. Turning he spindle clockwise increases he sensiiviy of he sensor. The signal on he bar graph is increased. Turning he spindle counerclockwise reduces he sensiiviy of he sensor. The signal on he bar graph is reduced. Adjusmen procedure The descripion is provided using he example of a dark mark on a ligh background. For he case of a ligh mark on a dark background, he erms mark and background simply need o be exchanged. 1.Posiioning he background under he ligh spo. If he bar graph indicaor is o he lef of he middle posiion, urn he muliurn poeniomeer clockwise unil he sensor swiches off (yellow indicaor LED Q1 off). Several full urns may be necessary here. LED Q1 off: Q1 2.Posiioning he mark under he ligh spo. If he bar graph indicaor is o he righ of he middle posiion, urn he muliurn poeniomeer counerclockwise unil he sensor swiches on (yellow indicaor LED Q1 on). Several full urns may be necessary here. LED Q1 on: Q1 3.Swich beween mark and background and wach he bar graph while doing so. Turn he muliurn poeniomeer unil he deflecion beween he mark and he background is symmeric abou he middle of he bar graph. 4.If you are no able o find a seing ha enables reliable deecion, repea he process wih a differen deecion color. Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0. 2-01 info@leuze.com www.leuze.com
Muliurn poeniomeer A removable operaing buon is plugged ino he muliurn poeniomeer a he facory. The seing of he conras sensor can hereby be performed manually wihou he need for a ool. If his is no desired, he operaing buon can be pulled off. A screwdriver is hen needed for he seing. Rear view of sensor wih operaing buon plugged If necessary, loosen hen operaing buon wih a screwdriver Color changeover Conras sensor KRT18B enables simple changeover of he deecion color on he device. This is necessary if he conras beween he mark and he background is no sufficien for reliable deecion wih he se color. Examples for opimum deecion colors: Color of he mark Color of he background Opimum deecion color Black Whie Any Red Whie Green Yellow Whie Blue Green Whie Red Black Red Red Black Green Green Black Blue Blue In general, he opimum deecion color can also be found by selecing he color for he which he larges signal difference is displayed beween mark and background on he bar graph. Press buon C (Color) for 2 7s (LEDs flash in sync wih a frequency of 2Hz) and release. 2 7s Upon release of he buon, he deecion color changes o he nex color (order: green, blue, red).. 2-01 2016/06
Mulicolor conras sensor L/D Ligh/dark swiching Press he C buon longer han 12s. Release he buon. To change he seing again, push he buon again for longer han 12 s and release. LED on = OUT1 (Pin 4): PNP ligh swiching, NPN dark swiching OUT2 (Pin 2) 1) : PNP dark swiching, NPN ligh swiching LED off = OUT1 (Pin 4): PNP dark swiching, NPN ligh swiching OUT2 (Pin 2) 1) : PNP ligh swiching, NPN dark swiching Only he green LED flashes. 1) Only for devices wihou analog oupu Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0. 2-01 info@leuze.com www.leuze.com
Sensor adjusmens via he IN inpu (Pin 5) Signal level 2V Signal level (U B -2V) Seing he deecion color Transmier color RED Swich o RED Transmier color GREEN = 20... 80 ms Swich o GREEN Transmier color BLUE = 120... 180 ms Swich o BLUE = 220... 280 ms Ligh/dark swiching PNP ligh swiching / ligh on, NPN dark swiching / dark on (OUT1) = 420... 480 ms PNP dark swiching / dark on, NPN ligh swiching / ligh on (OUT1) = 520... 580 ms Locking all operaional conrols via he IN inpu (Pin 5) A saic signal ( 20ms) a he IN inpu (Pin 5) locks all operaional conrols on he sensor if required, such ha no manual operaion is possible (e.g., proecion from erroneous operaion or manipulaion). If he inpu is no conneced or if a saic signal is being applied, all operaional conrols are unlocked and can be operaed freely. 12%. 2-01 2016/06