Solid-sae Muli-funcional Timer H3CR-A Timers DIN 48 x 48-mm Sae-of-he-ar Mulifuncional Timer A wider power range reduces he number of imer models kep in sock. A wide range of applicaions hrough six or four operaing modes. Reduced power consumpion. (Excep for H3CR-A8E) Enables easy sequence checks hrough insananeous oupus for a zero se value a any ime range. Lengh, when panel-mouned wih a Socke, of 80 mm or less. Time Seing Rings enable consisen seings and limi he seing range. Panel Covers enable various panel designs. PNP inpu models available. Rich variey of inpus:, rese, and gae funcions (11-pin models and -AP models) Model Number Srucure Model Number Legend H3CR-A@@@-@ 1 3 4 1. Number of Pins None: 11-pin models 8: 8-pin models. Inpu Type for 11-pin Models None: No-volage inpu (NPN ype) P: Volage inpu (PNP ype) 3. Oupu None: Relay oupu (DPDT) S: Transisor oupu (NPN/PNP universal use) E: Relay oupu (SPDT) wih insananeous relay oupu (SP- DT) 4. Suffix 300: Dual mode models (signal ON/OFF-delay and one-sho) 301: Double ime scale (range) models (0.1 s o 600 h) Solid-sae Muli-funcional Timer H3CR-A B-109
Ordering Informaion Lis of Models 11-pin Models Conac Oupu Supply volage Inpu ype Time range Operaing mode (see noe ) Transisor (Phoocoupler) 8-pin Models Conac 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC No-volage inpu 0.05 s o 300 h Six muli-modes: A, B, B, C, D, E Dual-modes: G, J Volage inpu Six muli-modes: A, B, B, C, D, E H3CR-A Model H3CR-A-300 H3CR-AP No-volage inpu 0.1 s o 600 h H3CR-A-301 0.05 s o 300 h H3CR-AS Oupu Supply volage Inpu ype Time range Operaing mode (see noe ) Transisor (Phoocoupler) Time-limi conac and insananeous conac 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 100 o 40 VAC (50/60 Hz)/ 100 o 15 VDC 4 o 48 VDC/VAC (50/60 Hz) No-inpu available 0.05 s o 300 h Four muli-modes: A, B, E, J ( sar) Model H3CR-A8 0.1 s o 600 h H3CR-A8-301 0.05 s o 300 h H3CR-A8S H3CR-A8E Noe: 1. Specify boh he model number and volage when ordering. Example: H3CR-A 100 o 40 VAC (50/60 Hz)/100 o 15 VDC Supply volage. The operaing modes are as follows A: ON-delay D: Signal OFF-delay B: Flicker OFF sar E: Inerval B: Flicker ON sar G: Signal ON/OFF-delay C: Signal ON/OFF-delay J: One-sho B-110 Solid-sae Muli-funcional Timer H3CR-A
Accessories (Order Separaely) Name/specificaions Models Flush Mouning Adaper Y9F-30 Y9F-73 Y9F-74 Mouning Track 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N End Plae PFP-M Spacer PFP-S Proecive Cover Y9A-48B Track Mouning/ 8-pin PCF-08 Fron Connecing Socke 8-pin, finger safe ype PCF-08-E 11-pin PCF-11 11-pin, finger safe ype PCF-11-E Back Connecing Socke 8-pin P3G-08 8-pin, finger safe ype P3G-08 wih Y9A-48G (see noe 1) 11-pin P3GA-11 11-pin, finger safe ype P3GA-11 wih Y9A-48G (see noe 1) Time Seing Ring Seing a specific ime Y9S-7 Limiing he seing range Y9S-8 Panel Cover (see noe ) Ligh gray (5Y7/1) Y9P-48GL Black (N1.5) Y9P-48GB Medium gray (5Y5/1) Y9P-48GM Hold-down Clip (see noe 3) For PL08 and PL11 Sockes Y9H-7 For PF085A Socke Y9H-8 Timers Noe: 1. Y9A-48G is a finger safe erminal cover which is aached o he P3G-08 or P3GA-11 Socke.. The Time Seing Ring and Panel Cover are sold ogeher. 3. Hold-down Clips are sold in ses of wo. Specificaions General Iem H3CR-A/-AS H3CR-AP H3CR-A8/-A8S H3CR-A8E Operaing mode A: ON-delay B: Flicker OFF sar B: Flicker ON sar C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval G: Signal ON/OFF-delay (Only for H3CR-A-300) J: One-sho (Only for H3CR-A-300) A: ON-delay (power sar) B: Flicker ON sar (power sar) E: Inerval (power sar) J: One-sho (power sar) Pin ype 11-pin 8-pin Inpu ype No-volage inpu Volage inpu --- Time-limi oupu ype H3CR-A/-A8/-AP:Relay oupu (DPDT) Relay oupu (SPDT) H3CR-AS/-A8S: Transisor oupu (NPN/PNP universal)* Insananeous oupu --- Relay oupu (SPDT) ype Mouning mehod DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C. No.14, NK, Lloyds Conforms o EN6181-1 and IEC60664-1 (VDE0110) 4kV/. Oupu caegory according o EN60947-5-1 for Timers wih Conac Oupus. Oupu caegory according o EN60947-5- for Timers wih Transisor Oupus. *The inernal s are opically isolaed from he oupu. This enables universal applicaion as NPN or PNP ransisor. Solid-sae Muli-funcional Timer H3CR-A B-111
Time Ranges Noe: When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. Sandard (0.05-s o 300-h) Models Time uni s (sec) min (min) h (hrs) x10 h (10 h) Full scale seing 1. 0.05 o 1. 0.1 o 1. 1. o 1 3 0.3 o 3 3 o 30 1 1. o 1 1 o 10 30 3 o 30 30 o 300 Double (0.1-s o 600-h) Models Time uni s (sec) min (min) h (hrs) x10 h (10 h) Full scale seing.4 0.1 o.4 0.4 o.4.4 o 4 6 0.6 o 6 6 o 60 4.4 o 4 4 o 40 60 6 o 60 60 o 600 Raings Raed volage (see noe 1) Operaing volage range rese Inpu consumpion 100 o 40 VAC (50/60 Hz)/100 o 15 VDC, 4 o 48 VAC (50/60 Hz)/1 o 48 VDC (4 o 48 VAC/VDC for H3CR- A8E) (see noe ) 85% o 110% of raed volage (90% o 110% a 1 VDC) Minimum power-opening ime: 0.1 s No-volage Inpu ON impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 100 kω min. Volage Inpu Max. permissible capaciance beween inpus lines (erminals 6 and 7): 1,00 pf Load connecable in parallel wih inpus (erminals 6 and 7). 100 o 40 VAC/100 o 15 VDC High (logic) level: 85 o 64 VAC/85 o 137.5 VDC Low (logic) level: 0 o 10 VAC/0 o 10 VDC 4 o 48 VAC/1 o 48 VDC High (logic) level: 0.4 o 5.8 VAC/10.8 o 5.8 VDC Low (logic) level: 0 o.4 VAC/0 o 1. VDC H3CR-A/-A8 100 o 40 VAC/100 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON: approx..0 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W) 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Relay ON: approx. 0.8 W Relay OFF: approx. 0. W H3CR-AP (see noe 3) 100 o 40 VAC/100 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON: approx..5 VA (. W) Relay OFF: approx. 1.8 VA (1.7 W) 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Relay ON: approx. 0.9 W Relay OFF: approx. 0.3 W H3CR-A8E 100 o 40 VAC/100 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON/OFF: approx. VA (0.9 W) 4 o 48 VAC/VDC (When a 4 VDC) Relay ON/OFF: approx. 0.9 W H3CR-AS/-A8S 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Oupu ON: 0.3 W Oupu OFF: 0. W Conrol oupus Time limi conacs: 5 A a 50 VAC/30 VDC, 0.15 A a 15 VDC, resisive load (cosφ = 1) Transisor oupu: Open collecor (NPN/PNP), 100 ma max. a 30 VDC max., residual volage: V max. Insananeous conac: 5 A a 50 VAC/30 VDC, 0.15 A a 15 VDC, resisive load (cosφ = 1) Noe: 1. DC ripple rae: 0% max. if he power incorporaes a single-phase, full-wave recifier.. Each 4-o-48-VAC/1-o-48-VDC model causes an inrush curren of approximaely 0.85 A. Pay careful aenion when aemping o urn ON power o such a model wih non-conac oupu from a device such as a sensor. 3. The values are for when he erminals and 7 and erminals 10 and 6 are shor-ed, and include he consumpion curren of he inpu. B-11 Solid-sae Muli-funcional Timer H3CR-A
Characerisics Accuracy of operaing ±0.% FS max. (±0.%±10 ms max. in a range of 1. s) ime Seing error ±5% FS ±50 ms (see noe 1) Rese ime Min. power-opening ime: 0.1 s max. Min. pulse widh: 0.05 s (H3CR-A/-AS) Rese volage 10% max. of raed volage Influence of volage ±0.% FS max. (±0.%±10 ms max. in a range of 1. s) Influence of emperaure ±1% FS max. (±1%±10 ms max. in a range of 1. s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh,000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed noncurren-carrying meal pars),000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ),000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher),000 VAC, 50/60 Hz for 1 min (beween inpu and conrol oupu erminals and operaion ) for H3CR-AP Impulse wihsand volage 3 kv (beween power erminals) for 100 o 40 VAC/100 o 15 VDC, 1 kv for 4 o 48 VAC/1 o 48 VDC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 40 VAC/100 o 15 VDC, 1.5 kv for 4 o 48 VAC/1 o 48 VDC and 4 o 48 VAC/VDC Noise immuniy ±1.5 kv (beween power erminals) and ±600 V (beween no-volage inpu erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 µs, 1-ns rise) Saic immuniy Malfuncion: 8 kv Desrucion: 15 kv Vibraion resisance Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude each in 3 direcions for hours each Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude each in 3 direcions for 10 minues each Shock resisance Desrucion: 1,000 m/s 3 imes each in 6 direcions Malfuncion: 100 m/s 3 imes each in 6 direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 5 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 0,000,000 operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 50 VAC, resisive load a 1,800 operaions/h) (see noe ) EMC (EMI) EN6181-1 Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN6181-1 Immuniy ESD: IEC61000-4-: 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC61000-4-3:10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves:IEC61000-4-3:10 V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC61000-4-6: 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC61000-4-4: kv power-line (level 3) kv I/O signal-line (level 4) Immuniy Surge: IEC61000-4-5: 1 kv line o line (level 3) kv line o ground (level 3) Case color Ligh gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 90 g Timers Noe: 1. The value is ±5% FS +100 ms o 0 ms max. when he C, D, or G mode signal of he H3CR-AP is OFF.. Refer o he Life-es Curve. Solid-sae Muli-funcional Timer H3CR-A B-113
Life-es Curve 10,000 Swiching operaions (x 10 3 ) 5,000 1,000 500 100 30 VDC L/R = 7 ms 50 VAC (cosφ = 0.4) 50 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 15 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma (100 ma for H3CR-A8E) a 5 VDC (failure level: P). Load curren (A) B-114 Solid-sae Muli-funcional Timer H3CR-A
Connecions Block Diagrams H3CR-A/AS AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor Timers Oscillaion Couning Oupu Rese inpu, sar inpu, and gae inpu Inpu Indicaor -ON indicaor Oupu-ON indicaor H3CR-AP AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor Oscillaion Couning Oupu Inpu Indicaor -ON indicaor Oupu-ON indicaor Solid-sae Muli-funcional Timer H3CR-A B-115
H3CR-A8/A8S AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor Oscillaion Couning Oupu Indicaor -ON indicaor Oupu-ON indicaor H3CR-A8E AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor Oscillaion Couning Oupu Indicaor -ON indicaor Oupu-ON indicaor Insananeous oupu I/O Funcions Inpus (for -A/ -AS models) Rese Noe: H3CR-AP incorporaes sar inpu only. s ime-measuremen. Inerrups ime-measuremen and reses ime-measuremen value. No ime-measuremen is made and conrol oupu is OFF while he rese inpu is ON. Gae Prohibis ime-measuremen. Oupus Conrol oupu Oupus are urned ON according o designaed oupu mode when prese value is reached. B-116 Solid-sae Muli-funcional Timer H3CR-A
Terminal Arrangemen Noe: The delayed conac of convenional Timers was indicaed as The conac symbol of he H3CR-A is indicaed as 11-pin Models because is operaing mode is six muli-modes (four muli-modes for he H3CR-A8). 8-pin Models Timers H3CR-A/-A-300/-A-301 (Conac Oupu) H3CR-A8/-A8-301 (Conac Oupu) Rese inpu inpu Gae inpu H3CR-A8S (Transisor Oupu) H3CR-AS (Transisor Oupu) Rese inpu inpu Gae inpu Noe: Terminals 1, 3, 4, and 5 are empy. Terminals and 7 are he same as for he H3CR-A8. H3CR-A8E (Conac Oupu) Noe: Terminals 1, 3, 4, and 8 are empy. Terminals, 5, 6, 7, and 10 are he same as for he H3CR-A. H3CR-AP (Conac Oupu) inpu Noe: Terminal 5 is empy. Solid-sae Muli-funcional Timer H3CR-A B-117
Inpu Connecions H3CR-A/-AS The inpus of he H3CR-A/-AS are no-volage (shor- or open) inpus. No-volage Inpus No-conac Inpu Conac Inpu No-conac Inpu (Connecion o NPN open collecor oupu sensor.) 1 o 4 VDC (sensor power ) + DC power (Connecion o a volage oupu sensor.) 1 o 4 VDC (sensor power ) + DC power Sensor Timer 5 Gae 6 7 Rese Timer 5 Gae 6 7 Rese Sensor Timer 5 6 7 Gae Rese Inpu (0 V) Inpu (0 V) Inpu (0 V) Operaes wih ransisor ON Operaes wih relay ON Operaes wih ransisor ON No-volage Inpu Signal Levels No-conac inpu Conac inpu 1. Shor- level Transisor ON Residual volage: 1 V max. Impedance when ON: 1 kω max.. Open level Transisor OFF Impedance when OFF: 100 kω min. Use conacs which can adequaely swich 0.1 ma a 5 V B-118 Solid-sae Muli-funcional Timer H3CR-A
H3CR-AP The sar inpu of he H3CR-AP is volage inpu. (Volage imposiion or open) Volage Inpus No-conac Inpu No-conac Inpu Conac Inpu (Connecion o PNP open (Connecion o NPN open collecor oupu sensor) collecor oupu sensor) 1 o 4 VDC (sensor power ) Sensor + 10 (+) 6 7 DC power Timer Operaes wih PNP ransisor ON Inpu 0V ( ) Sensor 1 o 4 VDC (sensor power ) + DC power 10 Operaes wih NPN ransisor ON 6 7 Timer (+) Inpu 0V ( ) AC power DC power Operaes wih relay ON 10 6 7 Timer (+) Inpu 0V ( ) Timers Volage Inpu Signal Levels No-conac inpu Noe: The inpu is isolaed from he power. Thus, an NPN ransisor can be conneced. 1. Transisor ON Residual volage: 1 V max. The volage beween erminals 6 and 7 mus be 10.8 VDC min. Noe: Refer o he signal levels in he following able and be aware of he minimum applicable load of he relay.. Transisor OFF Leakage curren: 0.01 ma max. The volage beween erminals 6 and 7 mus be 1. VDC max. Conac inpu Use conacs ha can adequaely swich 0.1 ma a each operaing volage. The volage beween erminals 6 and 7 wih conacs ON or OFF mus saisfy he specified value. Conacs ON 100-o-40-VAC and 100-o-15-VDC models: 85 o 64 VAC or 85 o 137.5 VDC 4-o-48-VAC and 1-o-48-VDC models: 0.4 o 5.8 VAC or 10.8 o 5.8 VDC Conacs OFF 100-o-40-VAC and 100-o-15-VDC models: 0 o 10 VAC or 0 o 10 VDC 4-o-48-VAC and 1-o-48-VDC models: 0 o.4 VAC or 0 o 1. VDC Solid-sae Muli-funcional Timer H3CR-A B-119
Operaion Timing Char Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The minimum inpu pulse widh (for sar, rese) is 0.05 s. 3. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. 4. sar in mode J is also possible for H3CR-A8/-A8E/-A8S/-A8-301 models. H3CR-A/-AS/-AP* *H3CR-AP model incorporaes sar inpu only. Operaing mode Timing char A: ON-delay Basic operaion B: Flicker OFF sar B: Flicker ON sar C: Signal ON/ OFFdelay Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor (see noe) Oupu Noe: inpu is invalid while he Timer is in operaion. Basic operaion (see noe) Oupu Noe: inpu is invalid while he Timer is in operaion. Basic operaion (see noe) Oupu Noe: inpu is invalid while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) (see noe) Oupu Oupu relay (NO) (Oupu indicaor) indicaor Noe: inpu is valid and reriggerable while he Timer is in operaion. B-10 Solid-sae Muli-funcional Timer H3CR-A
Operaing mode D: Signal OFFdelay Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Timing char Basic operaion (see noe) Oupu Noe: inpu is valid and re-riggerable while he Timer is in operaion. Timers E: Inerval Rese Oupu relay (NC) Basic operaion (see noe) Oupu G: Signal ON/ OFFdelay Oupu relay (NO) (Oupu indicaor) indicaor Basic operaion Noe: inpu is valid and re-riggerable while he Timer is in operaion. Rese Oupu relay (NC) (see noe) J: One-sho oupu Oupu relay (NO) (Oupu indicaor) indicaor Oupu Noe: inpu is valid and re-riggerable while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) (see noe) Oupu 1±0.6 s (Fixed) Noe: inpu is valid and reriggerable while he Timer is in operaion. Gae Signal Inpu ON OFF 1 Gae Rese ON OFF ON OFF ON OFF Oupu ON relay OFF Noe: 1. This iming char indicaes he gae inpu in operaing mode A (ON-delay operaion).. The se ime is he sum of 1 and. 3. H3CR-AP model incorporaes sar inpu only. Solid-sae Muli-funcional Timer H3CR-A B-11
H3CR-A8/-A8S Operaing mode Timing char A: ON-delay Basic operaion Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Oupu B : Flicker ON sar Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Basic operaion Oupu E: Inerval Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Basic operaion Oupu J: One-sho oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Basic operaion Oupu 1±0.6 s (Fixed) Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. B-1 Solid-sae Muli-funcional Timer H3CR-A
H3CR-A8E Operaing mode Timing char A: ON-delay Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) Basic operaion Oupu Timers indicaor B : Flicker ON sar Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Basic operaion Insananeous oupu relay (NO) Oupu indicaor E: Inerval Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) indicaor Basic operaion Oupu J: One-sho oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) (Fixed) (Fixed) Basic operaion Oupu 1±0.6 s (Fixed) indicaor Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. Solid-sae Muli-funcional Timer H3CR-A B-13
Nomenclaure Oupu indicaor (orange) (Li when oupu) indicaor (green) (Flashes when Timer operaes; li when Timer sops operaing) Operaing mode display window Operaing mode selecor Selec a mode from: A, B, B, C, D, and E (H3CR-A, -AP, and -AS) A, B, E and J (H3CR-A8, -A8S, and -A8E) G and J (H3CR-A-300) Scale range display windows Time range selecor (selec one from 1., 3, 1, and 30 a full scale; wih he H3CR-A@-301, selec from.4, 6, 4, or 60 a full scale. ) Time seing knob (se ime) Time uni display window Time uni selecor (selec one from sec, min, hrs, and 10h) B-14 Solid-sae Muli-funcional Timer H3CR-A
Dimensions Noe: All unis are in millimeers unless oherwise indicaed. H3CR-A H3CR-AP H3CR-AS 48 15 6 66.6 5.3 0.7 Timers 48 39 dia. 44.8 x 44.8 11 pins H3CR-A8 H3CR-A8S H3CR-A8E 48 15 66.6 6 5.3 0.7 48 39 dia. 44.8 x 44.8 8 pins Dimensions wih Se Ring 50 16.5 50 4 dia. Dimensions wih Fron Connecing Socke PCF-08-@/PCF-11-@ Time Seing Ring Panel cover Dimensions wih Back Connecing Socke P3G-08/P3GA-11 81.5 81.5 15 15 80 75 H3CR-A H3CR-AS 100.8* H3CR-AP 98.5 PCF-11 PCF-11-E.3* H3CR-A8@ 89.9* 87.6 PCF-08 PCF-08-E.3* H3CR-A H3CR-AS H3CR-AP + Adaper H3CR-A8@ + Adaper Y9F-30 P3GA-11 Y9F-30 P3G-08 (When (When Y9A-48G Y9A-48G mouned) mouned) *These dimensions vary wih he kind of DIN rack (reference value). Solid-sae Muli-funcional Timer H3CR-A B-15
Applicaion Examples (H3CR-A) A Mode: ON-delay ON-delay operaion (A mode) is a basic mode. 1. -ON /-OFF Rese The -ON sar/-off rese operaion is a sandard operaing mehod. 3. Conrol of Inegraed Time wih Gae Signal Wih a gae signal, he -ON sar operaion and Signal sar operaion can be conrolled (he operaion can be inerruped). ( and 10) 1 1 + : se ime ( and 6) ( and 10) Rese ( and 7) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Gae ( and 5) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) indicaor Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Exernally shor-ed Flashing Li Gae signal (The operaion is inerruped wih he gae signal if he Timer deecs an abnormal signal.) Exernally shor-ed. Signal /Signal Rese The Signal sar/signal rese operaion is useful for remoe conrol of he Timer. B/B Mode: Flicker ( and 10) ( and 6) Rese ( and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing signal (remoe conrol possible) Rese signal (remoe conrol possible) Li The flicker operaion in he B and B modes can be effecively applied o lamp or buzzer (ON and OFF) alarms or he monioring of an inermien operaion wih a display. 1. -ON /-OFF Rese (in B Mode) ( and 10) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Exernally shor-ed ( coninuously supplied) B-16 Solid-sae Muli-funcional Timer H3CR-A
. Signal /Signal Rese (in B Mode) If here is an abnormal signal, flashing sars. When he abnormal condiion is resored, a rese signal sops he display flashing.. Signal-ON-OFF /Insananeous Operaion/Time-limi Rese ( and 10) ( and 6) Rese ( and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li signal Rese signal ( and 10) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Flashing Li Flashing Li signal (The operaion sars wih he signal ON or OFF) Timers ( coninuously supplied) C Mode: Signal ON/OFF-delay The Signal ON-/OFF-delay operaion (C mode) is useful for he conrol of disribuion of producs on a producion line ino boxes by he specified number or ime. 1. -ON /Insananeous Operaion/ Time-limi Rese A se of hese funcions is useful for he operaion of a machine for a specified period when power is ON. ( coninuously supplied) D Mode: Signal OFF-delay Signal OFF-delay operaion (D mode) can be effecively used o keep a load operaing for a cerain period. For example, his funcion enables he cooling fan for a lamp or heaer o operae for a cerain period afer he lamp or heaer is swiched OFF. 1. -ON /Insananeous Operaion/ Time-limi Rese ( and 10) ( and 6) ( and 10) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Exernally shor-ed signal (NC o NO) Solid-sae Muli-funcional Timer H3CR-A B-17
. Signal /Insananeous Operaion/ Time-limi Rese ( and 10). Signal /Insananeous Operaion/ Time-limi Rese This funcion is useful for he repeiive conrol such as he filling of liquid for a specified period afer each Signal sar inpu. ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li ( and 10) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) signal (NO o NC o NO) signal E Mode: Inerval ( coninuously supplied) ( coninuously supplied) 1. -ON /Insananeous Operaion/ Time-limi Rese This funcion is useful for he operaion of a machine for a specified period afer power is ON. ( and 10) ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Exernally shor-ed B-18 Solid-sae Muli-funcional Timer H3CR-A
Precauions (H3CR-A) Noe: The undermenioned is common for all H3CR-A models. Supplies For he power of an inpu device of he H3CR-A@/-A@S/-AP, use an isolaing ransformer wih he primary and secondary windings muually isolaed and he secondary winding no grounded. Example: H3CR-A G, S, R 5, 6, 7 H3CR-A Inpu erminal 10 Inpu/Oupu Relaionship beween Inpu and Supply Circuis (excep for H3CR-A8E) The H3CR-A (excep for H3CR-A8E) uses ransformerless power. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shor-ing due o a sneak curren o he ransformerless power. If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no differ in phase, oherwise he erminals will be shor-ed o one anoher. Timers Inpu device Isolaion ransformer is required. The H3CR-A@/-A@S/AP s power erminal is a common erminal for inpu signals o he Timer. Do no disconnec he wires on erminal, oherwise he inernal ry of he Timer will be damaged. Incorrec Conac or ransisor for exernal inpu signal H3CR-A Inpu erminal Shor- curren 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A Correc Inpu erminal Inpu erminal Make sure ha he volage is applied wihin he specified range, oherwise he inernal elemens of he Timer may be damaged. Inpu erminal I is impossible o provide wo independen power swiches as shown below regardless of wheher or no he Timers are differen in phase. Inpu erminal Inpu erminal Solid-sae Muli-funcional Timer H3CR-A B-19
Relaionship beween Inpu and Supply Circuis (H3CR-A@/-A@S) An appropriae inpu is applied o he inpu signal erminals of he H3CR-A@/-A@S when one of he inpu erminals is shor-ed wih he common erminal (erminal ) for he inpu signals. Never use erminal 10 as he common erminal for his purpose, oherwise he inernal of he Timer will be damaged. Incorrec 10 If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no be differen in phase or he erminals will be shor-ed o one anoher (refer o he figures below). Incorrec Conac or ransisor for exernal inpu signal 6 7 10 H3CR-AP AC or DC power 5, 6, 7 G, S, R Inpu erminal H3CR-A 6 7 10 H3CR-AP Shor- curren Correc AC or DC power 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A Correc Conac or ransisor for exernal inpu signal 6 10 7 H3CR-AP Do no connec a relay or any oher load beween inpu erminals, oherwise he inernal of he Timer will be damaged due o he high-ension volage applied o he inpu erminals. 6 10 Shor- curren Ry 10 7 H3CR-AP AC or DC power Inpu conac 5, 6, 7 G, S, R Inpu erminal H3CR-A Relaionship beween Inpu and Supply Circuis (H3CR-AP) Common o All H3CR-A Models Wih he H3CR-AP, inpu wires mus be as shor as possible. If he floaing capaciy of wires exceeds 1,00 pf (approx. 10 m for cables wih 10 pf/m), he operaion will be affeced. Pay paricular aenion when using shielded cables. The H3CR-A@S ransisor oupu is isolaed from he inernal ry by a phoocoupler. Therefore, eiher NPN or PNP oupu is possible. H3CR-AP AC/DC power Inpu Since he inpu and he power are configured independenly, he inpu can be urned ON or OFF irrespecive of he ON/OFF sae of he power. I mus be noed ha a volage equivalen o he power volage is applied o he inpu. B-130 Solid-sae Muli-funcional Timer H3CR-A