Copy OWNER S MANUAL MODEL N OUTDOOR STORAGE. Keep this Identification Number in case you must contact our Customer Service Department.

Transcription

1 OUTDOOR STORAGE MODEL N OWNER S MANUAL Copy Keep this Identification Number in case you must contact our Customer Service Department.

2 REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefits to registering your Lifetime product. With our new online product registration form, it s fast and easy! Register with us at and enjoy these great benefi ts: LIFETIME S PROMISE TO YOU: Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes. We invite you to read our privacy policy at REGISTER today! **U.S. and Canada customers ONLY** DO NOT CONTACT THE STORE! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) Lifetime Products, Inc. Copy SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Most injuries are caused by misuse and/or not following instructions. Use caution when using this product. INSTRUCTION 11/19/010

3 BEFORE BEGINNING ASSEMBLY *Two adults *Two required adults to complete required to assembly* complete assembly* (+ one adult suggested as an instruction reader) Only adults should set up the product. Do not allow children in the set-up area until assembly is complete. TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY 3/4" 7/16 Power Drill Socket Wrench with 3/4 & 1/ Sockets # Phillips Screwdriver 1/8" Drill Bit Rubber Mallet Safety Glasses (1) (1) (1) (1) (1) (1) (1) (1 for each person) 3

4 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is located at the top, right-hand corner of the page and shows an image of the product with shaded parts indicating which section is being assembled. # This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.! Note: These areas are usually located in the bottom, right-hand corner of a step and indicate that damage to the product or serious injury may occur if the caution or warning is not heeded. CAUTION WARNING Throughout the Parts & Hardware List, Part & Hardware Identifiers, and instructions are three-letter IDs. These IDs are below the images of the parts and hardware to help you locate and identify the parts and hardware during assembly. These IDs are not necessarily on the parts themselves. ADZ

5 MAIN COMPOSTER PARTS ID Description Qty BIV COMPOSTER PARTS KIT PARTS & HARDWARE LIST ID Description Qty BJJ HARDWARE BAG BIS TUMBLER ASSEMBLY HARDWARE BIT BASE ASSEMBLY HARDWARE Main Composter Parts PARTS IDENTIFIER BHN BHQ BHM BHP 5

6 Main Composter Parts PARTS IDENTIFIER BII BIH Composter Parts Kit [BIV] BJA BIX WARNING BIY BIZ BJB BJC 6

7 Tumbler Assembly Hardware [BIS] HARDWARE IDENTIFIER BHO AAN BTK BIR BHK ADW ARA BIK ADM BIP BIM BIO Base Assembly Hardware [BIT] BIL AKH ADJ ABU BIJ BIN 7 BHJ

8 1 BASE FRAME ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: BIT BIN ABU BIJ SMALL PARTS REQUIRED BHJ ADJ BIX PARTS REQUIRED BII BIH TOOLS REQUIRED Phillips Screwdriver 7/16 Wrench Electric Drill w/phillips Head Safety Glasses 8

9 1 NO HARDWARE REQUIRED FOR THIS STEP 1.1 ADULTS REQUIRED FOR THIS STEP BASE ASSEMBLY A-Frame Weldments (BII) Composter Leg (BIH) Repeat this step for the second Composter Leg. BIH BII BII Outer Housing Brackets are on the outside. 9

10 1 BHJ 1. #8 x 1/ Phillips Self-Tapping Screws (BHJ) Do not overtighten Screws. BHJ BHJ BHJ BHJ 10

11 1 BIN BIX 1.3 Locking Pin Spring (BIN) Locking Pin Assembly (BIX) BIN BIX WARNING 11

12 1 7/16 ABU BIJ ADJ 1.5 Inner Housing Brackets (BIJ) Cap Nut (ADJ) Locking Pin ADJ BIJ ABU ABU ADJ BIJ WARNING 1

13 TUMBLER ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: BIS BTK AAN BHO BIR BHK ADW BIK ADM AKH BIL BIO SMALL PARTS REQUIRED BIM BIP BJA BIZ BIY BJB BJC 13

14 TUMBLER ASSEMBLY (CONT.) PARTS REQUIRED BHN BHM BHQ BHP TOOLS REQUIRED Phillips Screwdriver Rubber Mallet Safety Glasses 1/8 Drill Bit (ARA) (Included) Electric Drill w/phillips Head

15 1/ AAN BIR BHO TUMBLER ASSEMBLY.1 Mounting End Plate (BHP) End Panel (BHM) 5/16 Steel Flat Washers (BHO) 5/16 Cap Nuts (AAN) Repeat this step for the second End Panel. Warning Sticker AAN BHO BIR AAN AAN BHO BIR BHO BHP BIR BHM The extruded end of the Mounting End Plate goes toward the Tumbler. 15

16 BIL BIO BIK BIP. 1/ Flat Washer (BIO) Sleeve (BIL) 5/8 Flat Washer (BIP) over a. BIK BIL BIO BIP.3 Grease Packet (AKH) Repeat steps. -.3 for the second set of Washers, Bushing, Sleeve, and Hex Bolt. Tear here AKH 16

17 BIM Bolt, Washer, and Sleeve Assembly Be sure to insert a Black Plastic Spacer (BIM) between the End Panel and the Inner Housing Bracket of the A-Frame as shown. Warning Sticker Bolt, Washer, and Sleeve Assembly BIM 17

18 ADM BIO.5 BIO ADM 18

19 NO HARDWARE REQUIRED FOR THIS PAGE ADULTS REQUIRED FOR THIS STEP.6 Orient the second End Panel to match the first to align the two ventilation holes. Have another adult hold this second Panel in place. Locking Pin Lifetime Logo! Note: These two ventilation holes must be aligned. 19

20 ARA ADW.7 ADULTS REQUIRED FOR THIS STEP Place a Panel/Lid (BHN) It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Repeat this step for the other side of the Front Panel/Lid. Divots in Front/Lid Panel BHN ADW Divots in End Panel! Note: It s OK if the Screws (ADW) spin freely at this point. Don t worry about stripping the plastic. 0

21 NO HARDWARE REQUIRED FOR THIS PAGE.8 Ventilation Tube (BHQ) BHQ Ventilation Hole Lifetime Logo 1

22 BJC.9 ADULTS REQUIRED FOR THIS STEP Double Hook Straps (BJC) Panel/Lid (BHN) (Fig. 1) (Fig. ). BHN BJC BJC Fig. 1 Fig.

23 ADW ARA.10 Pan-Head Screws (ADW) It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. ADW ADW 3

24 ARA ADW BHK.11 Repeat step.7 for the next Panel/Lid. Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten. BHN ADW BHK

25 ARA BJA ADW BHK.1 Latch Assemblies (BJA) Head Screw (ADW) It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten. ADW ADW BJA BJA 5

26 ADW BHK ARA BIY.13 Pinned Hinges (BIY) It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten. ADW ADW BIY BIY 6

27 ADW ARA BJB BIZ BHK Place two Hinge Tubes (BJB) Lid (BHN). It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. place a Plastic Nut (BHK) Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten. BHN ADW BJB ADW BJB BHK BHK.15 Place two Latch Hooks (BIZ). It s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Place a Plastic Nut (BHK) Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten. Set aside for later. ADW ADW BIZ BIZ BHK BHK 7

28 BTK.16 Blow Hole Plug (BTK) Repeat this step for each Panel/Lid. BTK 8

29 NO HARDWARE REQUIRED FOR THIS STEP.17! Note: Remove Lid when filling and emptying Tumbler. 9

30 3 NO HARDWARE REQUIRED FOR THIS STEP LOCKING THE COMPOSTER 3.1 Latch Hook Latch Assembly wire 3. Repeat steps for second Latch. 30 WARNING

31 LIFETIME COMPOST TUMBLERS 5-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS. REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE. FOR INTERNATIONAL WARRANTY CLAIMS: R 31

32 ENHANCE YOUR LIFETIME PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS To purchase accessories or other Lifetime Products, visit us at: Or call: