ASPEN OUTDOOR TABLE TENNIS

Transcription

1 ASPEN OUTDOOR TABLE TENNIS Replacement Parts Order direct at or call our Customer Service department at (800) am to :30 pm Central Standard Time January 201 UPC Code

2 Staple your receipt here. Important: A copy of your receipt will be needed to activate your warranty (see page 18)

3 Congratulations and THANK YOU for purchasing the Aspen Outdoor Table Tennis. You have chosen a product that should provide years of entertainment. To assist you with customer service and warranty claims, staple your receipt to the inside cover, then keep this manual in a safe place for future reference. GLD Products S8 W19093 Enterprise Drive Muskego, WI USA Fax: gld@gldmfg.com Web: This manual may have been updated. For the latest manual visit the GLD products website. Place your package near the location where it will be used. Carefully unpack all components and verify you have all the correct pieces. If you notice missing or defective parts, please call us at: ext 113. Please read and understand all instructions before beginning assembly. This assembly will require 2 adults. This product is not for use by children without adult supervision

4 GLD Products Parts Identifier Part No./ Qty Illustration/ Order Number Part No./ Qty Illustration/ Order Number Part No./ Qty Illustration/ Order Number 3 Leg Order No Leg Link Order No Table Top Leg Stabilizer Order No Caster Support Order No Wheel Order No Wheel Support Order No Side Support Order No Paddle Holder Order No Hex Head Bolt M12 x 10 mm Order No Hex Head Bolt M8 x 85 mm Order No Net Pin Order No. 9-0 Net Holder Order No Net Order No. 9-1 Center Bracket Order No. 9-3 Phillips Head Screw M8 x 60 mm Order No Hex Head Bolt M8 x 60 mm Order No Hex Head Bolt M6 x 50 mm Order No. 9-18

5 GLD Products Hex Head Bolt M6 x 0 mm Order No Nut M6 Order No. 9-6 Washer 8 mm I.D. Order No Nut M5 Order No Washer 5 mm I.D. Order No Spacer 6 mm I.D. Order No Washer 12 mm I.D. Order No Spacer 8 mm I.D. Order No Washer 6 mm I.D. Order No Phillips Round Head Screw M5 x 25 mm Order No Locking Nut M8 Order No Washer Head Nut M12 Order No Phillips Round Head Screw M5 x 15 mm Order No Hex Head Bolt M6 x 65 mm Order No Spacer Order No

6 IF YOU HAVE A WARRANTY CLAIM, CALL US FIRST Please see page 18. GLD Products Available 8 am to :30 pm Central Standard Time S8 W19093 Enterprise Drive Muskego, WI USA Fax: gld@gldmfg.com Web: For all claims, please have your receipt and item number when you call. The product item number can be found on the front cover. If you are instructed to return the product for service, you are responsible for shipping the unit at your expense. PRODUCT REGISTRATION Important: The product registration form on page 19 and a copy of your receipt must be completed and returned within 10 days of purchase to validate your warranty. Online registration is also available. Go to /index.php/registration or click on this link. Follow the online instructions. Preparing for Assembly Be sure to unpack all of the parts included in this package. Some parts may be in obscure locations of the packaging. Check inside any tubes or sleeves. Save all packing material until the product is fully assembled and functional. Compare the parts in your package with the Parts Identifier description on pages and 5. After unpacking large products, some disassembly may be required prior to beginning the assembly

7 Tools Required Hex Open End Wrenches: 8 mm, 10 mm, 13 mm, and 18 mm (not included) Phillips screwdriver (not included) Electric screwdriver may be helpful. CAUTION: You must set at LOW TORQUE and use extreme caution because you could overtighten the hardware, strip the screws, or damage the table. Rubber mallet or hammer (not included) Precautions to Prevent Personal Injury and Damage Indoor only tables will not withstand outdoor conditions. If using the table outdoors, move it indoors as soon as possible. Be alert for surface changes when moving the table. Cracks and changes in the slope may cause the table to tip over. The table is not designed for supporting heavy loads. Do not place heavy items on the table. Collapse of the support structure is possible. Do not sit or stand on the top of the table. When using the table all the support legs and wheels must be in contact with the floor. Failure to properly support the table may damage the frame and table top. Opening or closing the table presents a risk for pinching. Keep all children away and alert adults when moving the table top up or down. Liquids left on the playing surface for extended peroids will damage the table top. Wipe up any spills immediately. For Outdoor Tables Strong winds may move or tip the table over. Take precautions as needed to prevent damage or injury. Do not leave balls or paddles outside. They will likely be damaged by outdoor conditions

8 Assembly Tips Make sure you understand the following before you begin to assemble your table tennis. 1. READ THIS MANUAL all the way through before beginning assembly. 2. When installing parts that have more than one bolt, start ALL bolts in that part by hand before tightening anything. 3. Some drawings or images in this manual may not look exactly like your product.. You will need a second adult to assist with this assembly. Note: Save all packing materials until the parts have been inspected and the table is assembled. Unpack the Pieces Lay the box on a flat surface (floor). You may want this near your area of assembly. Unpack the boxes and part bags. Inspect and count the parts. The Parts Identifier page can be used to record your results. If any parts are damaged or missing contact GLD customer service. Missing fasteners may be purchased at a hardware store using the descriptions on the Parts Identifier page(s). Paddles and balls not included

9 STEP 1 - ASSEMBLE CASTER SUPPORTS 1. Locate the two caster supports (#5). 2. Position a wheel support (#7) and insert a bolt (#1) thru the support and then thru the caster support. 3. Place a washer (#2) onto the bolt and secure the assembly with a washer head nut (#20). The caster support must rotate smoothly.. Locate two wheels (#8) and insert a bolt (#16) thru a wheel, the caster support and the second wheel. 5. Use a locking nut (#21) to secure the wheels. Tighten the locking nut and be certain the wheels roll smoothly. 6. Repeat numbers 2 thru 5 on the second wheel assembly. 7. Locate the parts for the second wheel and support assembly. Follow numbers 1 thru

10 STEP 2 - ASSEMBLE SIDE SUPPORTS AND CENTER BRACKET 1. Locate the two side supports (#9), the center bracket (#6) and the paddle holder (#10). 2. Position one of the side supports (#9) so the smooth side will face away from the wheel assembly. 3. Insert two screws (#15) thru the side support and into the caster support.. Hold the screws in position and place one end of the center bracket (#6) over the screws. 5. Use a washer (#25) and a locking nut (#21) to secure the three pieces. 6. Repeat numbers 2 thru 5 on the other end of the center bracket. 7. On one end of the assembly, position the paddle holder (#10). Insert two screws (#30) thru a washer (#28) and the holder. Hold the screws in place thru the holes in the side support (see detail A). 8. Tighten two nuts (#23) onto the screws A

11 STEP 3 - ATTACH LEGS TO TABLE TOP The two table tops (#1) are the same. Lay the first one down on a flat surface with the underside facing up. 1. Locate two of the leg stabilizers (#). 2. From the outside of the table, insert a bolt (#19) with a washer (#29) thru the support rail (see detail B). 3. Place a spacer (#26) onto the bolt.. Position the leg stabilizer (#) over the bolt. 5. Use a washer (#29) and a nut (#22) to hold the stabilizer. When the nut has been tightened, the stabilizer should be able to rotate on the bolt. 6. Repeat numbers 2 thru 5 on a second leg stabilizer (#). 7. Insert a bolt (#32) with a washer (#29) thru the holes at the end of one of the legs (#2) (see detail C). The legs (#2) have a rubber bumper pre-installed on the leg. The bumper must face to the center of the table. This will keep the legs in position so the table opens smoothly. 8. Place a spacer (#26) over the bolt. Insert the bolt thru the inside support from the outside edge inward. 9. Use a washer (#29) and a nut (#22) to secure the leg. The leg should be able to rotate on the bolt. C Bumper must face to center B

12 10.Attach one end of the leg link (#3) to one of the inside legs (#2) (see detail D). 11.Use a bolt (#18) and washer (#29) and insert it thru the leg stabilizer (#). 12.Add a washer (#29) and push the bolt thru the hole in the end of the leg link (#3). 13.Place a spacer on the bolt so it is between the leg link and the leg. 1.Secure with a washer (#29) and a nut (#22). CAUTION: The preassembled legs must be installed with the shorter distance, Y, between the center hole and the free end of the leg. The distance X, between the center hole and the other end of the leg, is longer. If the leg is not installed correctly, remove the leg from the table top. Move the plastic end piece to the other end, and re-attach the correct leg end to the table top. 15.To attach the preassembled leg to the leg link, use a bolt (#19) and washer (#29) inserted thru the leg. Place a spacer (#26) over the bolt (see detail E). 16.Place the end of the leg link over the bolt. Secure it with a washer (#29) and a nut (#22). 17.Repeat numbers 10 thru 16 for the other side of the table. NOTE: The legs should move smoothly. Adjust the tightness of the nuts and bolts as needed. One table top is now completely assembled. Position the second table top and follow numbers 1 thru D This leg is preassembled to table top. X Y E

13 STEP - PLACE TABLE TOPS INTO THE FRAME Each table top has a spring loaded handle. Pull on the handle and place two spacers (#33) onto the rods below the plate. The spacers will prevent the handles from returning to the start position Use two adults to lift one table top above the side supports. 2. The rubber guides at the corners of the table top are inserted into the half round openings in the track on the side supports. Once the guides are in the tracks, the table top will move down to the bottom. CAUTION: One adult must hold the table top upright. Failure to hold the table up will allow it to fall possibly causing injury. Start guide here 3. Pull up on the handle and remove the two spacers (#33). When the handle is released a post will move into a slot in the side support on both sides.. An adult should continue to steady the table top. Attach the preassembled legs to the caster supports

14 5. Use a bolt (#17) and washer (#25) and insert it thru the caster support. Place a spacer (#27) on the bolt (see detail F). 6. Place the leg over the bolt and secure with a washer (#25) and nut (#21). 7. Repeat numbers thru 6 on the second side. CAUTION: Do not lower the table top at this time. The assembly is not balanced and may tip over. 8. Attach the second table top by following numbers 1 thru F

15 STEP 5 - OPENING AND CLOSING THE TABLE CAUTION: To Open the Table Use two adults to open or close the table. 1. Hold the top edge and lift and hold the table lock handle. 2. Bring the top edge towards you. The two lock pins will release. The legs will open as the table swings down. 3. When the legs are fully open, release the handle. Lift up on both sides of the table near the net to snap the table locks into position.. Repeat numbers 1 thru 3 on the second half of the table. Pins release Pins snap into lock position

16 To Close the Table 1. The net does not need to be removed. 2. Pull back and hold the table lock handle. The pins will release. 3. Lift up on the end of the table.. As the table goes up, the legs will fold in. The inside edge of the table will move down. 5. When the table is fully up, release the handle. The table locks will snap into position. CAUTION: Be certain the table is locked when in the raised position. If not properly locked, the table can swing down causing damage or personal injury. 6. Repeat numbers 2 thru 5 on the second half of the table. Pins release Pins snap into lock position

17 STEP 6 - ATTACH THE NET Use two adults when opening or closing the table. When both sides are open, attach the net. Open the table by pulling outward on the top edge. The legs should open into position as the top moves down. 1. Position one of the net holders (#11) at the top center of the side support (#9) (see detail G). 2. Use two screws (#31) with washers (#28) to position the net holder. 3. Use a nut (#23) on each screw to secure.. Insert a net pin (#12) into the end of the net (#13) (see detail H). 5. Pivot the net holder up into position, and then down to lock (see detail G). Push the net with a pin into the post (see detail I). If the top of the net has a string, pull the string over the top of the post. Hook the string on one of the openings in the post. 6. Repeat numbers 1 thru 5 on the other side of the table. G H 12 I

18 90-DAY LIMITED WARRANTY The Manufacturer warrants to the original retail purchaser that this product is free from defects in material and workmanship under normal use and conditions for a period of ninety (90) days from the date of original purchase. The Manufacturer s liability is limited to the repair or replacement, at its option, of any defective product and shall not include any liability for indirect, incidental or consequential damages of any kind. Should this product become defective due to material or workmanship within the warranty period, contact our Customer Service Department. This warranty is not transferable and does not cover normal wear and tear or damage caused by improper usage, negligence, misuse, abuse, transportation damage, acts of nature, or accident (including failure to follow the instructions in this manual). It does not cover expendable items such as batteries, light bulbs, fuses, accessories, cosmetic parts and other items that wear out due to normal usage. This warranty is also void if the product is disassembled and reassembled, damaged, modified from its original state, or used for other than indoor personal residential use (no commercial or rental applications). This warranty gives you specific legal rights, and you may have other rights which vary from state to state. IF YOU HAVE A WARRANTY CLAIM, CALL US FIRST (8 - :30 CST) Please have your receipt and item number (found on the front cover) when you call. GLD Products S8 W19093 Enterprise Drive Muskego, WI USA Fax: gld@gldmfg.com Web: If you are instructed to return the product for service, you are responsible for shipping the unit at your expense to the above address in packaging that will protect against further damage. All warranty or repair requests require a Return Authorization Number prior to returning the item. PRODUCT REGISTRATION Important: The product registration form on page 19 must be completed and returned along with a copy of your receipt within 10 days of purchase to validate your warranty. Online registration is also available. Go to /index.php/registration or click on this link. Follow the online instructions

19 REGISTER YOUR PRODUCT Place postage here Complete this form, include a copy of your receipt, fold, tape (do not staple) and return within 10 days of purchase. This protects your warranty and will help us develop new products! Cut here. GLD Products Warranty Department S8 W19093 Enterprise Drive Muskego, WI USA Fold here second. GAME TABLES GAMES AND ACCESSORIES BILLIARD ACCESSORIES SOFT-TIP DARTS FLIGHTS AND SHAFTS HOME CASINO BILLIARD CUES DARTBOARDS STEEL-TIP DARTS DART CASES AND ACCESSORIES Fold here first. Name Date of Purchase Address Phone-Day City Phone-Evening State Zip Purchase Price: Store Name: Item: Aspen Outdoor Table Tennis Remember to attach a copy of your receipt.

20 This page left intentionally blank.

21 Mail To: GLD Products S8 W19093 Enterprise Drive Muskego, WI USA FAX Web Site: Name Date Address Phone-Day City Phone-Evening State Zip Parts Re-Order Form Order No. Description Unit Price Each Total Amount 9-30 Leg Leg Link Leg Stabilizer Caster Support Center Bracket Wheel Support Wheel Side Support Paddle Holder Net Holder Net Pin Net Hex Head Bolt M12 x 10 mm Phillips Head Screw M8 x 60 mm Hex Head Bolt M8 x 85 mm Hex Head Bolt M8 x 60 mm Hex Head Bolt M6 x 50 mm Hex Head Bolt M6 x 0 mm Washer Head Nut M Locking Nut M Washer Head Nut M Nut M Washer 12 mm I.D Washer 8 mm I.D Spacer 6 mm I.D Spacer 8 mm I.D Washer 5 mm I.D Washer 6 mm I.D Phillips Round Head Screw M5 x 15 mm Phillips Round Head Screw M5 x 25 mm Hex Head Bolt Spacer 0.20 Subtotal Shipping will be added. If paid by Check or Money Order, call for quote. S/H 5.1% Waukesha Wisconsin tax will apply (subject to change). Tax Total

22 Method of Payment Check or Money Order Credit Card Visa MasterCard Discover American Express Card # Security Code # Billing Address Zip Code Signature Exp. Date Shipping Address Name Address Phone City State Zip