Copy OWNER S MANUAL MODEL N Keep this Identification Number in case you must contact our Customer Service Department.

Size: px

Start display at page:

Download "Copy OWNER S MANUAL MODEL N Keep this Identification Number in case you must contact our Customer Service Department."

Allyson Cameron
5 years ago
Views:

1 MODEL N OWNER S MANUAL Copy Keep this Identification Number in case you must contact our Customer Service Department.

2 REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefits to registering your Lifetime product. With our new online product registration form, it s fast and easy! Register with us at and enjoy these great benefi ts: LIFETIME S PROMISE TO YOU: Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes. We invite you to read our privacy policy at REGISTER today! **U.S. and Canada customers ONLY** DO NOT CONTACT THE STORE! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Copy SAFETY INSTRUCTIONS Most injuries are caused by misuse and/or not following instructions. Use caution when using this system. Instruction # B 11/26/2010 2

3 BEFORE BEGINNING ASSEMBLY Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. *TWO ADULTS REQUIRED TO COMPLETE ASSEMBLY* TOOLS REQUIRED FOR THIS ASSEMBLY 8 mm & 10 mm Wrench 2.5 mm Allen Wrench Needle-Nosed Pliers Safety Glasses 3

4 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is located at the top, right-hand corner of the page and shows an image of the product with shaded parts indicating which section is being assembled. # This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.! Note: These areas are usually located in the bottom, right-hand corner of a step and indicate that damage to the product or serious injury may occur if the caution or warning is not heeded. CAUTION WARNING Throughout the Parts & Hardware List, Part & Hardware Identifiers, and instructions are three-letter IDs. These IDs are below the images of the parts and hardware to help you locate and identify the parts and hardware during assembly. These IDs are not necessarily on the parts themselves. ADZ 4

5 ID Item Description Qty CTW Leg & Bench Assembly Hardware Bag PART ILLUSTRATIONS PARTS LIST PARTS IDENTIFIER ID Item Description Qty CTX Hinge & Table Top/Back Rest Assembly Hardware Bag CRK CTK CRL CRI CRJ CTR 5

6 LEG & BENCH ASSEMBLY HARDWARE BAG [CTW] HARDWARE IDENTIFIER 47 mm CSI 52 mm CTV AON CSH HINGE & TABLE TOP/BACK REST ASSEMBLY HARDWARE BAG [CTX] CUK *CTT *CTS *CTQ 54 mm 52 mm CSJ CTV CTU CTL CTM AON CTN CTO CTP 6

7 1 LEG & BENCH ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: CTW 47 mm 52 mm CSI CTV AON CSH PARTS REQUIRED CRK CRL CRI CRJ TOOLS REQUIRED HARDWARE BAG REQUIRED: CTW CSH Safety Glasses 7

8 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 10 mm (x2) AON CSI 47 mm 1.1 Right Leg (CRJ) M6 x 1 x 47 mm Hex-Head Bolts (CSI) CRJ 1.2 Lifetime Logo is on bottom Cross Support (CRL) M6 x 1 Cap Nuts (AON) Tighten Nuts securely, but do not overtighten. CSI CSI CRL Lifetime Logo faces outward as shown AON 8 AON WARNING

9 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 10 mm (x2) AON CSI 47 mm 1.3 **TWO ADULTS REQUIRED FOR THIS STEP** Left Leg (CRI) to Tighten Nuts securely, but do not overtighten. CRI CSI AON CSI AON WARNING 1.4 Bench Assembly (CRK) Align these holes. CRK Cross Bar Location Nub 9

10 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 10 mm (x2) AON CTV 52 mm 1.5 Tighten Nuts securely, but do not overtighten. Repeat this step for the right side of the Bench Assembly. Left-Most Brace AON CTV AON CTV WARNING 10

11 2 HINGE & TABLE TOP/BACK REST ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: CTX CUK CTP *CTT *CTS *CTQ 54 mm 52 mm CSJ CTV CTM CTN AON CTL CTO CTU PARTS REQUIRED CTK CTR TOOLS REQUIRED HARDWARE BAGS REQUIRED: CTW, CTX CSH CTP Needle-Nosed Pliers Safety Glasses 11

12 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 CUK 2.1 1/2 Round Cap Plug (CUK) Metal Tube (CTR) CUK CUK CTR CUK CTR These holes must be aligned 12

13 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 CTT CTS 2.2 Adjustment Plate (CTT) CTT 2.3 Adjustment Fork (CTS) (Fig. 1) (Fig. 2). CTS Fig. 1 Fig. 2 13

14 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 CTU CTT 2.4 Adjustment Plate (CTT) CTT 2.5 Cotter Key (CTU) If necessary, use a pair of pliers or needle-nosed pliers to help insert the Cotter Key. CTU 14

15 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 8 mm CTM CTQ CTL 2.6 Adjustment Lever (CTQ) #8 x 7/8 Button-Head Screws (CTM) #8 Nylock Nuts (CTL). Repeat sections for the other end of the Metal Tube. CTQ CTL CTL 2.7 CTM CTM Align these holes Align these holes and grooves Set Adjustment Fork into the nook on the Legs as shown. 15

16 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 10 mm (x2) 54 mm CTN CSJ CTO AON 2.8 M6 x 1 x 54 mm Hex-Head Bolts (CSJ) 1/4 Flat Washers (CTN) more 1/4 Flat Washers (CTN) M6 x 1 Cap Nuts (AON) Repeat this step for the other side of the Metal Tube. CSJ CTN CTN AON 2.9! Note: Do not overtighten Nuts and Bolts. WARNING Spring (CTO) Repeat this step for the Spring on the other side of the Metal Tube. CTO Stretch the upper loop of the Spring up and over the Adjustment Fork and into the groove. Connect the bottom loop of the Spring to this Bolt. 16

17 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 10 mm (x2) 52 mm CTV AON 2.10 Table Top/Back Rest (CTK) CTK! 2.11 Note: These two holes go toward the front as shown. Repeat this step for the other side of the Table Top/Back Rest Assembly. AON AON CTV CTV WARNING 17

18 3 TABLE-TO-BENCH/BENCH-TO-TABLE CONVERSION Adjustment Lever Adjustment Lever 18

19 CLEANING & CARE Cleaning and Care 12 19

20 LIFETIME 2-YEAR LIMITED FACTORY WARRANTY LIFETIME PRODUCTS, INC. RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS. REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE. FOR INTERNATIONAL WARRANTY CLAIMS: Lifetime Products, Inc. 20

Copy OWNER S MANUAL MODEL N Keep this Identification Number in case you must contact our Customer Service Department.

Copy OWNER S MANUAL MODEL N Keep this Identification Number in case you must contact our Customer Service Department. MODEL N 80055 OWNER S MANUAL Copy Keep this Identification Number in case you must contact our Customer Service Department. REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefits to registering your