JPR-THEW Installation Instructions 1 GENERAL INFORMATION
|
|
- Annis Floyd
- 5 years ago
- Views:
Transcription
1 JPR-THEW Installation Instructions 1 GENERAL INFORMATION Your THIN Extension consists of a combination of Light Segments and Standoffs. It can be a single Light Segment with one Power Standoff and one End Standoff at either end, Or multiple Light Segments connected by Pass-Through Standoffs, with one Power Standoff and one End Standoff at either end. Installation Type Description Power Supply/Driver PLUG-IN pages 2-4, 8 REMOTE DRIVER DIRECT pages 2, 5, 8 For easy repositioning of fixture, requires nearby wall outlet. Includes: Remote control with wall mounted holder Wall mounted cord wrap The most minimal installation method. In-wall low voltage cable wired directly into the standoff. Class 2-24VDC 1.5A wall outlet adapter - dimmable via included remote control Class 2-24VDC remote driver - dimmable via compatible wall switch, refer to driver specifications Juniper recommends Lutron DVCL-253P dimmers for use with our Standard drivers IMPORTANT: TO PREVENT ELECTRIC SHOCK, ALWAYS DISCONNECT THE POWER BEFORE INSTALLING FIXTURE AND BEFORE CLEANING OR OTHER MAINTENANCE HARDWIRED FIXTURES SHOULD BE INSTALLED BY A LICENSED ELECTRICIAN - INSTALL ACCORDING TO NATIONAL ELECTRIC CODE AND LOCAL REGULATIONS CLASS 2 POWER SUPPLY REQUIRED
2 JPR-THEW Installation Instructions 2 24 Inch Light Segment (a1) PART GLOSSARY 36 Inch Light Segment (a2) Power Standoff (c1) Plug-in Power Standoff (c1) Pass-through Standoff (c2) End Standoff (c3) Standoff Bracket(b) OR Set Screw(f) #8 Pan Head (d) 8-32 Countersunk (g) Wire Nuts (n) #8 Countersunk (e) 8-32 Pan Head (h) PLUG-IN OPTIONAL PARTS Remote (j1) Remote Holder (j2) Cord Wrap (k1) Cord Wrap Mount (k2) MOUNTING DIAGRAM Use a level to mark the locations of the Standoff Brackets for your chosen Light Segment length. The fixture may be mounted horizontally or vertically according to your application. 24 inches (609.6mm) 36 inches (914.4mm)
3 JPR-THEW Installation Instructions 3 PLUG-IN INSTALLATION PLUG-IN STEP 1 Fix the Standoff Brackets (b) to the wall using supplied Screws (d) and appropriate anchors (if necessary). b d PLUG-IN STEP 2 Route the cord through one of three exit holes, then slip the Plug-in Power Standoff (c1) over the Standoff Bracket (b). Note: be sure to align the set screw holes on the Standff and Mounting Bracket. CORD WRAP STEP 1 Mark the mounting location of the Cord Wrap (k1), making sure that the cord runs tangentially to the inner post. c1 k1 CONTINUE TO PAGE 4
4 JPR-THEW Installation Instructions 4 PLUG-IN INSTALLATION CONTINUED CORD WRAP STEP 2 Using the supplied #8 Countersunk Screw (e) and/ or Drywall Anchor (i), fix the Cord Wrap Mount (k2) to the wall. CORD WRAP STEP 3 Thread the Cord Wrap (k1) onto the Cord Wrap Mount. e k2 CORD WRAP STEP 4 Making sure the cord coming from the fixture is taut, wrap it around the Cord Wrap, ensuring enough cord left to reach an outlet. REMOTE HOLDER STEP 1 Using supplied #8 Countersunk Screws (e) and Drywall Anchors (i)(if necessary), fix the Remote Holder (j2) to the wall. j2 e to 24VDC wall adaptor CONTINUE TO PAGE 6
5 JPR-THEW Installation Instructions 5 REMOTE DRIVER DIRECT INSTALLATION REMOTE DRIVER DIRECT STEP 1 Mount the Standoff Brackets (b) to the wall using the supplied Screws (d) and appropriate anchors (if necessary, additional blocking may be required to secure the bracket). Make sure to allow space for the 24VDC supply wires coming through the slot from the wall. d b + - REMOTE DRIVER DIRECT STEP 2 Using supplied Wire Nuts (n) make connection between the 24VDC supply wires and the fixture leads. Push the wire nuts into the Power Standoff (c1), and slide the Standoff over the Standoff Bracket. Note: be sure to align the set screw holes on the Standoff and Standoff Bracket. c1 NOTE: POWER MUST BE 24VDC CLASS 2, DO NOT CONNECT TO AC POWER/HOUSE WIRING Red(+) Black(-) CONTINUE TO PAGE 6
6 JPR-THEW Installation Instructions 6 FINAL INSTALLATION (PLUG-IN/REMOTE DRIVER DIRECT) FINAL INSTALLATION STEP 1 Slide the Light Segment (a1 or a2) into the mounted Standoff (either Pass-Through (c2) or End Cap (c3) depending on number of Light Segments). FINAL INSTALLATION STEP 2 Slide the next Standoff (c2 or c3, depending on number of Light Segments) onto the Light Segment. a1 or a2 c2 or c3 a1 or a2 c2 or c3 FINAL INSTALLATION STEP 3 Slide the Standoff (c2 or c3, depending on number of Light Segments) onto the Standoff Bracket. Repeat steps 1-3 for additional Light Segments. FINAL INSTALLATION STEP 4 For Plug-in and Remote Driver Direct installations, secure all installed Standoffs with supplied set screws (f). Note: you may gently rotate the Light Segment into the desired orientation with two hands, one at either end of the segment. a1 or a2 f c2 or c3
7 JPR-THEW Installation Instructions 7 CARE INSTRUCTIONS Like other natural metals, brass will patina over time, with the natural yellow hues intensifying over time. Juniper protects its brass with a mild matte lacquer to delay coloration of the metal, and to protect it from exposure to humidity and natural oils. In order to remove dirt, dust and fingerprints; gently wipe the lamp with a damp cloth. Do not use any chemical cleaning solutions; especially those containing ammonia, as this will damage the surface finish of the brass. Do not drop or apply excessive force on any part or joint of the lamp. Do not attempt to disassemble or modify it in any way except for recycling. Do not use the lamp for any purpose other than its intended use. Use indoors only. Please contact us should the lamp not operate as described, and we will be happy to assist you.
THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationG. H. I. N. J. O. 22"x 28" Poster Holder. P. Q. romotional wall displ
Wall Display Assembly Instructions Tools necessary for assembly 1. Electric drill with Phillips head 2. Adjustable wrench or pliers 3. One or two step ladders or stools Due to the weight of the side panels
More informationUR20/UR28 Ouro Site/Area Luminaire Installation Instructions
17760 Rowland Street City of Industry, CA 91748 626/968-5666 FAX 626/369-2695 UR20/UR28 Ouro Site/Area Luminaire Installation Instructions! WARNING: Fixtures must be grounded in accordance with local codes
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationSarspec, Lda. - Rua Camilo Castelo Branco, 965 PQ Vila Nova de Gaia Phone:
2 3 IMPORTANT SAFETY NOTE: Before operating this device, please read carefully this User Manual and be familiar with its contents prior to using this equipment. To help avoid potential serious injury to
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationMonitor mount for 2017 P-series Dell monitors. Installation guide
Monitor mount for 2017 P-series Dell monitors Installation guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION
More informationOptima 450 LED Edge-Lit Single-Sided Light Box. Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1. Tools you ll need
Installation Instructions Optima 450 LED Edge-Lit Single-Sided Light Box Figure 1 INSTALLATION INSTRUCTIONS Before you begin These instructions illustrate the Stylmark Optima 450 LED Edge-Lit Single-Sided
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationInstalling Fixture Using Remote Power Supply
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.edgelighting.com info@edgelighting.com 904-BV2-2K4K-_03 BV2-1RE-_-2K4K-_ Installation
More informationMyStudio VS53 Versa Sweep Setup Instructions
MyStudio VS53 Versa Sweep Setup Instructions MISSION STATEMENT Pro Cyc, Inc. is the world leader in design and sales of modular infinity backgrounds. Our studio systems are recommended by every major company
More informationLED Thin Frame Fixed Frame Screen User Guide
LED Thin Frame Fixed Frame Screen User Guide INTRODUCTION INTRODUCTION WARNING - Sharp Edges This product may contain sharp edges, please handle with care. Protective gloves are recommended. WARNING -
More informationGas Lift Bed Assembly Instructions (please retain this instruction for future reference)
Gas Lift Bed Assembly Instructions (please retain this instruction for future reference) To assemble your bed you have been supplied with 12 x 12mm button head bolts, 4 x 15 mm Philips Head Screws, 6 Philips
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationInstallation Operation Care
Installation Operation Care Designer Roller and Designer Screen Shades Standard and Cassette Cordless Lifting System CONTENTS Getting Started: Product Views... 1 Tools and Fasteners Needed... 3 Installation
More informationUser Manual. Digital Compound Binocular LED Microscope. MicroscopeNet.com
User Manual Digital Compound Binocular LED Microscope Model MD82ES10 MicroscopeNet.com Table of Contents i. Caution... 1 ii. Care and Maintenance... 2 1. Components Illustration... 3 2. Installation...
More informationPARTS ENCLOSED: (A) Wall anchor (1) (B) Wall screw (1) (C) 4W Type G Bulb (1) (included)
making it easy to create an elegant nursery or child's bedroom. Each item s surface is sealed, which (A) Wall anchor (1) (B) Wall screw (1) (C) 4W Type G Bulb (1) (included) MARQUEE SYMBOL DOT For safety
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationNew Roman Shades WARNING. Installation Operation Care. Retractable Cord Lifting System
CHILD SAFETY Warning WARNING For more safety information call 1-888-501-8364 in the U.S. or 1-866-662-0666 in Canada. Young children can wrap cords around their necks and STRANGLE. Always keep cords out
More informationInstallation Instructions Parasol Cellular Shades
Installation Instructions Parasol Cellular Shades SlideArch CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the Installation s Inside
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationINSTALLATION GUIDE Hisense Laser TV Display Screen
INSTALLATION GUIDE Hisense Laser TV Display Screen Before you install this product, read this guide completely and make sure you understand all of the content. ES-G1811M2-1 ENGLISH Product Description
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationAeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material
Aeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material User s Guide Product Description: The Aeon CLR Series is an ultra-short throw fixed
More information1. TOOLS + MATERIALS REQUIRED
R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED
More informationInstructions for Catalina Round/Square Extension Tables
Unpack the table onto a soft level surface and identify the listed items. Instructions for Catalina Round/Square Extension Tables Hardware included: ¼ - #20 x 35mm s (4) ¼ - #20 x 50mm s (8) Cross nuts
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna
Release 3.0 NN47251-311 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna How to get help To access the complete range of services and
More informationAltus Installation Instructions
General Product information This product is suitable for indoor dry locations only. This product can be dimmed on the socket. Plug the fixture into a non-dimmed outlet. 1 Align the screw holes and secure
More informationElara NanoEdge Fixed Frame Screen User Guide
Elara NanoEdge Fixed Frame Screen User Guide INTRODUCTION INTRODUCTION WARNING This product may contain sharp edges, please handle with care. Protective gloves are recommended. A minimum of two people
More informationCLEARVIEW DAY COVER. Operation and Installation Instructions
CLEARVIEW DAY COVER Operation and Installation Instructions For information or technical assistance, call TOLL FREE: (800) 735-DUKE (3853) OR 314-231-1130 229652B Contents I. OVERVIEW AND TECHNICAL SPECIFICATIONS...3
More informationT-5 Floor Model SunLite Garden Assembly Instructions
T-5 Floor Model SunLite Garden Assembly Instructions The Floor Model Light Garden can be used alone or as a base for our popular Tabletop Light Garden (sold separately). Assembly takes less than an hour
More informationAeon CineGrey 3D Series
Aeon CineGrey 3D Series EDGE FREE Ceiling/Ambient Light Rejecting Fixed Frame Screen USER S GUIDE Version 2 (Spring type) Product Description: The Aeon Series is a fixed frame projection screen that uses
More informationAeon ALR Series. EDGE FREE Ambient Light Rejecting Fixed Frame Screen USER S GUIDE
Aeon ALR Series EDGE FREE Ambient Light Rejecting Fixed Frame Screen USER S GUIDE Product Description: The Aeon ALR Series is a fixed frame projection screen with an EDGE FREE design The EDGE FREE design
More informationELPMB27. Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs)
ELPMB27 Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs) Safety Instructions Before using the wall mount, make sure you read all of the safety instructions
More informationUser Instructions and Assembly UP UP DOWN DOWN UP UP DOWN DOWN. Siesta Chairs SIESTA. Perfect design. Personal service.
R R R User Instructions and Assembly Siesta Chairs SIESTA Perfect design. Personal service. WHY SIESTA? Siesta Backwash and Conventional Congratulations. You have purchased the most advanced and comfortable
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationInteractive Monitor Arm
Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE:
NEW VERDERA INSTALLATION INSTRUCTIONS MIRRORED CABINET K-78202T-L/K-78202T-R/K-78282T BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials,
More informationInstallation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe mounting of MP90 equipment on the anesthesia machine. WARNING: USE OF MOUNTING
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationFabric tiered drum pendant 30in Assembly and Installation Instructions
CAUTION: Fabric tiered drum pendant 30in Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationRIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly )
RIPPER PEDAL Bearing / Axle Replacement ( Disassembly ) 1 1. Use good quality tools to avoid stripping screw sockets. 2. When servicing your pedals, work on one side at a time to prevent parts from mixing
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationPower Bar, 12 & 16 Receptacle
Power Bar, 12 & 16 Receptacle Assembly Instructions Hello! Thank you for choosing Anthro s Power Bar! Before beginning installation of your Power Bar, please review the parts list below to verify that
More informationOMM300. Inverted Metallurgical Microscope
OMM300 Inverted Metallurgical Microscope Instruction Manual Please read the instructions carefully before operating CONTENTS Safety 2 Parts List 2 Features 3 Assembly 5 Operation 7 Maintenance 9 Specifications
More informationQuick Set Dovetail Jig
Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT
More informationIMPORTANT:
ASSEMBLY INSTRUCTIONS FOR KARISMA TWIN & FULL SIZE BEDS AND CONVERTIBLE CRIBS FULL SIZE BED OPTION (PLEASE REFER TO ASSEMBLY INSTRUCTIONS FOR YOUR 550 CONVERTIBLE CRIBS ) 555 5532 5530 5537 IMPORTANT:
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More informationFan, Eden/Northfield, GS Installation Instructions (SKU ) Packing List
Packing List Blower Assembly Wiring Harness Rheostat with Nut and Knob Snap Disc Mounting Hardware (4) rubber grommets with brass inserts, (4) nuts, (4) washers. Cover Assembly Installation Warning: Make
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationHOLLY HUNT LIGHTING. STUDIO H EDGE CHANDELIER Installation Instructions
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationMESO X1 TBAR SEMI-RECESSED
MESO X1 TBAR SEMI-RECESSED 93t-inst PAGE 1 OF 2 1 2 A IMPORTANT Do not remove packaging around fixture until after fixture is installed. The packaging protects and in some cases supports the fixture during
More informationRMD3000 DPO3000 Series Rackmount Kit
Instructions RMD3000 DPO3000 Series Rackmount Kit 071-2424-00 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationWall Mount Bracket YM-81
CN/JA/EN/DE/FR/ES/IT/SV/RU/PT/TR/NL/PL/FI/CS/NO/LT/TH/ID/MS/VI/TW/KO/AR Wall Mount Bracket YM-81 English User s Guide Deutsch Bedienungsanleitung Français Mode d emploi Español Italiano Svenska Português
More informationTitan - Double Skin Steel Partitioning. Installation Pack
Titan - Double Skin Steel Partitioning Installation Pack Troax Lee Manufacturing Ltd. Scan me Troax Lee Manufacturing Ltd Telephone : +44 (0) 1384 277 441 Building 52, Third Avenue, Facsimilie : +44 (0)
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationRTI TECHNOLOGIES, INC.
RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally
More informationInstallation Instructions For Reveal
2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com
More informationSLOT INSTALLATION GUIDE Indoor IP20
Please read entire guide prior to starting installation. Sections: Pre-Installation Single Run Fed From Both Ends NOTES 1. IP40 and lower tape must be installed indoors only. Installing outdoors will void
More informationIMPORTANT SAFETY INSTRUCTIONS:
Online: www.ballarddesigns.com PRODUCT NAME: MR Geometric Chandelier ITEM NUMBER: LC971 DIMENSIONS OF ITEM ASSEMBLED: FLUSH- 36 H x 42 W x 30 1/2 D HANGING- 96 H x 42 W x 30 1/2 D HANGING FIXTURE: FLUSH
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationL182 - Installation Sheet Modular Wine Rack ( Wall Mount )
Modular Wine Rack ( Wall Mount ) 1A 1B 2B 2A Cross Bar Options: 1A 2A 1B 2B Modular Wine Rack ( Wall Mount ) Parts Rail LED arm modules Wine bottle cross bars Rail cover Setscrew cover 1) Drill holes and
More informationCordless Operable Sidelights
Installation Instructions Parasol Cellular Shades Cordless Operable Sidelights CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the
More informationBLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationRM4000 Tektronix 4000 Series Rackmount Kit
Instructions RM4000 Tektronix 4000 Series Rackmount Kit 071-2134-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless
More informationInstallation Guide. SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs
Installation Guide SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs This series consists of the following: Model SN-LM42D Model SN-LM42DR Model SN-LM42S Model SN-LM42SR CAUTION: In order
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationM4 Foot Operated Underpinner Instruction Manual
M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner
More informationInstallation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe installation of MP40/50/60/70 mounting equipment on the anesthesia machine.
More informationTauten Tab Tension Screen User Manual
Tauten Tab Tension Screen User Manual Thank you for choosing a Tauten Series Tab Tension screen by Cirrus Screens. Please read through this user manual and understand all instructions before installing
More informationMicro Channel. Shorten the Fixture (optional) Installation Instructions for 700UMCD_ UNILUME. This product is suitable for damp locations.
Installation Instructions for Micro Channel 700UMCD_ 90MICRO. UNILUME GENERAL PRODUCT I NFORMATION: This product is suitable for damp locations. This product can be dimmed with a low-voltage electronic
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationVIT SB-16SS Pedestal. Conversion Guide
Converting a to Baseline This guide describes the steps for removing another manufacturer s irrigation controller from a VIT SB-16SS pedestal and installing a Baseline controller. Remove All Parts of the
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationPrepare the Fixture. Sage 37 Bath. Back Plate Installation (Horizontal) Installation Instructions for 700BCSAGW37_
Installation Instructions for Sage Bath 00BCSAGW_ 90BCSAGEL.0 BATH COLLECTION GENERAL PRODUCT I NFORMATION: This fixture is intended to be installed utilizing NEC compliant junction boxes. This product
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationRM4000 DPO4000 Series Rackmount Kit
Instructions RM4000 DPO4000 Series Rackmount Kit 071-1846-00 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationCorded Honeycomb Shades
Corded Honeycomb Shades Remove shade from package. Save packaging until shade is installed and working to your satisfaction. Level Tape Measure Pencil Power drill Screwdriver s for different mounting surface:
More information