END VIEW WEDGE TOP VIEW WOOD POST FOUNDATION DETAILS
|
|
- Eleanor Carpenter
- 5 years ago
- Views:
Transcription
1 X (NOMINAL POST) 1-1/ DIA. 2 HOLES X 8" (NOMINAL POST) 3-1/ DIA. 2 HOLES TAPERED HARD WOOD WEDGES (HARDWOOD WEDGE TO BE OAK, MAPLE OR OTHER APPROVED DENSE HARDWOODS) TO HOLD POST IN A STABLE POSITION AFTER CONCRETE HAS SET. USE OR 3" WEDGES TO COVER APPROXIMATELY 75% OF POST WIDTH ON TWO ADJACENT SIDES. 18" MINIMUM 1-1/ FILLET OF BITUMINOUS WATER PROOFING MATERIAL 3' (FOR X POST) 4.5' (FOR X 8" POST) STEEL AND CONCRETE PROJECTION ABOVE GROUND 10 GAUGE STEEL SLEEVE BOTH ENDS OPEN (ASTM A-653) WOOD POST MATERIAL OF MDOT STANDARD SPECIFICATIONS FOR CONSTRUCTION CONCRETE PER MDOT STANDARDS SPECIFICATIONS FOR CONSTRUCTION PLYWOOD OR EQUIVALENT + 8" X 8" X 5/8" X 1 X 5/8" - DEPENDING ON POST SIZE TO 3" MAXIMUM OF TAMPED EARTH 3-15/1 OR NOTE: INSIDE DIMENSIONS OF SLEEVE MAY BE A MAXIMUM OF 1/8" GREATER THAN SHOWN. 5-15/1 CONCRETE ENCASEMENT WEDGING OR 3" 1/8" 7" 3/ 18" DIA. 10 GAUGE STEEL SLEEVE BOTH ENDS OPEN (ASTM A-653) 5-15/1 OR 7-15/1 TACK WELD WEDGE WOOD POST FOUNDATION DETAILS DEPARTMENT DIRECTOR Kirk T. Steudle FOR Michigan Department of Transportation PREPARED BY APPROVED BY: DIRECTOR, BUREAU OF FIELD SERVICES WOOD POSTS DESIGN DIVISION DRAWN BY: CHECKED BY: DHD AJU APPROVED BY: DIRECTOR, BUREAU OF HIGHWAY DEVELOPMENT 05/01/15 08/13/14 1 OF5
2 5-1/ OR 7-1/ (ACTUAL) ( X (NOMINAL) POST) 1-1/ DIA. 2 HOLES ( X 8" (NOMINAL) POST) 3-1/ DIA. 2 HOLES 18" THE POST MAY BE DRIVEN OR PLACED IN AN AUGERED HOLE. IF AUGERED, BACKFILL WITH EXISTING MATERIAL IN FIVE 1 DEEP LAYERS, TAMPING EACH LAYER. 5' C L 8" DIA. AUGERED HOLE (FOR 3-1/ x 5-1/ POST) 10" DIA. AUGERED HOLE (FOR 5-1/ x 7-1/ POST) WOOD POST DIRECT EMBEDMENT DETAIL SINGLE POST INSTALLATIONS ONLY NOTE: DIRECT EMBEDMENT ONLY AT LOCATIONS IDENTIFIED IN PLANS OR PROPOSAL. * 1/ SAW CUT (EXCEPT IN SINGLE POST ASSEMBLIES) 5-1/2 " OR 7-1/ ACTUAL 3-1/ OR 5-1/ (FOR X NOMINAL POST) 1" (FOR X 8" NOMINAL POST) 1-1/ 7' 5' SLOPE (ALL WOOD POSTS) 1 5' 1 MULTIPLE POST SINGLE POST 7' SAW CUT DETAIL BREAKAWAY HOLES/SAWCUT RELATIONSHIP * SAW CUT SHALL BE PLACED ON APPROACH TRAFFIC SIDE OF POST. 2 OF5 NOTE: THE ORIGINAL SIGNED COPY IS KEPT ON FILE AT THE.
3 X (NOMINAL) OR X 8" (NOMINAL) WOOD POST 1-1/ 3/8" DIA. BOLT, 2 FLAT WASHERS & NYLON INSERT LOCKNUT STIFFENER ANGLE ALUMINUM L X 3" X 3/8" ANGLES MAY BE INSTALLED ON EITHER SIDE OF EACH POST. 1 1/6 SIGN LENGTH ALUMINUM EXTRUSION C LOF POST SINGLE TYPE I SIGN 3/8" DIA. RECTANGULAR FLAT BOLTS, FLAT WASHERS & NYLON INSERT LOCKNUTS. 3/8" DIA. BOLTS C LOF HOLES FOR 3/8" DIA. BOLTS. BOLT STIFFENER ANGLE TO EACH PANEL. 1/ X 3/ ELONGATED BOLT ON APPROX. 2 CENTERS FULL HOLES MAY BE USED TO FACILITATE LENGTH ALL EXTRUSIONS. O.015" SEE NOTE 5 ON 5 1/ 0.040" EXTERIOR CORNER RADIUS TYP. PANEL WIDTH 30" MAX. 30" MAX. 1 MAX. TYPICAL HOLE SPACING 1-1/ ALIGNMENT OF ALUMINUM ANGLES. SEE SIGN ALUMINUM EXTRUSION PER MDOT STANDARD SPECIFICATIONS FOR CONSTRUCTION STIFFENER ANGLE- L X X 1/ (ALUM.) x SIGN HEIGHT FLAT WASHER 7/8" O.D. X 0.40 I.D. X 0.050" 1/ X 3/ ELONGATED BOLT HOLES MAY BE USED TO FACILITATE 1 MAX. REAR VIEW ALIGNMENT OF PANELS. TYPE I SINGLE SIGN - ERECTION DETAILS 3 OF5 NOTE: THE ORIGINAL SIGNED COPY IS KEPT ON FILE AT THE.
4 7-1/ (FOR x 8" POST) 1-1/ 3/8" DIA. BOLT, 2 FLAT WASHERS & NYLON INSERT LOCKNUT (TYP). 4 BOLTS PER ANGLE. 8 BOLTS PER POST. 1/6 SIGN LENGTH ALUMINUM A A EXTRUSION C L OF POST x 3" x 3/8" ALUMINUM ANGLE x 8" (NOMINAL) WOOD POST BACK-TO-BACK TYPE I SIGNS INSIDE ANGLE OUTSIDE ANGLE 1 MAX. 9" 9" 1 MAX. NOTE: REFER TO TYPE I SIGN-ERECTION DETAILS FOR CONNECTING ANGLES TO BACK OF SIGNS. SECTION A-A TYPE I BACK-TO-BACK SIGNS-ERECTION DETAILS 4 OF5 NOTE: THE ORIGINAL SIGNED COPY IS KEPT ON FILE AT THE.
5 L 1/6 L 2/3 L 1/6 L 3/8" DIA. HEX. HD. BOLT NYLON INSERT LOCKNUT FLAT WASHER FLAT WASHER NYLON WASHER SAME AS BOLT ABOVE EXCLUDE CUT ON SINGLE POST ASSEMBLIES * CONNECTION DETAIL * SAW CUT SHALL BE PLACED ON APPROACH TRAFFIC SIDE OF POST. TYPES II & III SIGNS - ERECTION DETAILS NOTES: 1. THE DRILLED BREAKAWAY HOLES ARE TO BE CAREFULLY CENTERED ON THE POSTS. 2. ALL CONCRETE FOUNDATIONS SHALL BE FINISHED AS SHOWN AND ANY SURPLUS MATERIAL SHALL BE COMPLETELY REMOVED FROM RIGHT-OF-WAY. SIGNS SHALL NOT BE ERECTED ON WOOD POSTS FOR A MINIMUM OF 24 HOURS AFTER PLACEMENT OF THE CONCRETE. 3. THE PAY ITEM "SIGN, TYPE " INCLUDES ALL ATTACHING DEVICES AND HARDWARE. 4. WOOD POSTS MAY BE DIRECTLY EMBEDDED ONLY AT THOSE LOCATIONS IDENTIFIED IN THE PLANS OR PROPOSAL. 5. A 0.500" WIDE X O.015" DEEP GROOVE SHALL RUN THE ENTIRE LENGTH AT TOP AND BOTTOM OF ALL EXTRUDED ALUMINUM PANELS TO ACCOMMODATE OVERLAP ING. 6. ALL BOLTS, NUTS, AND WASHERS SHALL BE MDOT STANDARDS SPECIFICATIONS FOR CONSTRUCTION. 7. FIELD DRILL ALUMINUM ANGLES AND WOOD POSTS. 8. ALL SIGNS SHALL BE ATTACHED SO THAT THE BOLTS ARE CENTERED HORIZONTALLY ON THE POSTS. 5 OF5 NOTE: THE ORIGINAL SIGNED COPY IS KEPT ON FILE AT THE.
5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationMISCELLANEOUS SIGN CONNECTION DETAILS TYPICAL ROUTE MARKER ASSEMBLIES SIGN TO POST MICHIGAN DEPARTMENT OF TRANSPORTATION
5-4" SEE DETAIL I COUPLING BAR ON 3 2-10" CANTILEVER SIGN SUPPORT TYPICAL ROUTE MARKER ASSEMBLIES 5/1 DIAMETER STAINLESS STEEL BOLT AND NYLON INSERT LOCK NUT SELF-ALIGNING STEEL REINFORCING PLATE ( TYPE
More information(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" 8-0" 6-0" Truss Depth. 3" sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection (See details sheets 3 & 4 of 10) \ Span (Odd number of panels) \ Span (Even number of panels) Back truss chord Top truss chord \ Truss Chord splice Truss depth (See details \ Left
More informationTYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection Chord splice (see details (See details sheets 3 & 4 of 10) s Top truss chord Free end panel 10-0" Support end panels length varies (See chart below) \ Truss Back truss chord Top
More informationE:\Wilmot\DGN\14018pp.dgn 3/11/2015 6:49:16 AM
600-06 SHOULDER WIDENING FOR TYPE (SPECIAL) GUARDRAIL TERMINALS E:\Wilmot\DGN\08pp.dgn //05 6:9:6 AM E:\DGN\08SUP.dgn //05 ::55 PM E:\DGN\08SUP.dgn //05 :8:0 PM E:\DGN\08-WRG.dgn //05 :8:5 PM E:\DGN\08SM.dgn
More informationDELINEATOR REFERENCE POINT 200' TYPICAL SPACING (YELLOW DELINEATORS) END OF MERGE LANE TAPER DELINEATOR REFERENCE POINT
200' TYP. 600' < EACH SIDE BOTH ROADWAYS END OF MERGE LANE TAPER TYPICAL FOR ALL 2-LANE MERGES EXCEPT WHERE THERE IS A MERGE FROM THE RIGHT AND NO OFFSET IN THE THROUGH LANES END OF MERGE LANE TAPER 200'
More informationPlastibeton Trench System. Installation Packet
Plastibeton Trench System Installation Packet Plastibeton Installation Guide This Installation Guide is intended to assist in the preparation and installation of Plastibeton products manufactured by Oldcastle
More informationShoulder Wedge Maker
Shoulder Wedge Maker 1.0 Purpose and Use of the TransTech Shoulder Wedge Maker The Shoulder Wedge Maker is used as a paver attachment tool to help construct a higher density, longer lasting, low angle
More informationInstallation Instructions
Installation Instructions SRT-350 8 POST Guardrail End Treatment Revised July 2005 TRINITY HIGHWAY SAFETY PRODUCTS, INC. BUILDING TOMORROW S HIGHWAY SAFETY SOLUTIONS TODAY 2 SRT TM 8-POST SYSTEM FOR SPECIFIC
More informationPlastibeton Trench System. Installation Packet
Plastibeton Trench System Installation Packet Plastibeton Installation Guide This Installation Guide is intended to assist in the preparation and installation of Plastibeton products manufactured by Oldcastle
More informationBRIDGE RAILING, 4 TUBE B-26-F POST DETAILS MICHIGAN DEPARTMENT OF TRANSPORTATION
\ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x 6" SLOTTED ROUND HEAD BOLTS, WITH 1 PLATE WASHER, 1 LOCK WASHER AND HEX. NUT \ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x
More informationSIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationSIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationB-27-A BRIDGE RAILING, 3 TUBE WITH PICKETS SECTION THROUGH RAILING WITH BRUSH BLOCK SECTION THROUGH RAILING WITH SIDEWALK
3" 1'- ƒ " 11 " 7 " TOP OF REAR FLANE TO BE ROUND 2'- LON PICKET 1'- W6 x 25 1 " THICK BASE PLATE " " ELASTOMERIC BOUND FABRIC PAD 8" SLAB DETAIL A (SEE 3) OVERHAN SECTION THROUH RAILIN WITH BRUSH BLOCK
More informationSTEEL CANTILEVER TYPE E MICHIGAN DEPARTMENT OF TRANSPORTATION NOTE: EDGE OF SIGN VARIABLE 12" (MAX) 5'-0" COLUMN CAP 9'-5" (MAX) (TYP) DETAIL C
EDGE OF SIGN VARIABLE 12" (MAX) 25'-0" OLUMN AP 9'-5" (MAX) DETAIL END AP 1'-6" 4'-0" ARMS OPTIONAL SPLIE SIGN SIGN AND ARMS JP 1'-3" (MIN) 5'-0" 0.4 x L (MAX) OPTIONAL SPLIE VAIRES (25'-0" MAX) SEE ONTRAT
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationInstallation Manual for Metal Emperor Lockers
P a g e 1 Table of Contents Page General Notes and Tools Required 2-3 Assemble Shelves with Coat Hooks/Coat Rods 4 Fastening Chart 5 Knock Down Locker Assembly (Banks of Three) 6-12 Appendix A: Dress End
More informationItem 550 Chain Link Fence
Item Chain Link Fence 1. DESCRIPTION 2. MATERIALS Furnish, install, remove, repair, or replace chain link fence and gates. Furnish certification from the chain link fence materials manufacturer stating
More informationPost & Rail Crossbuck
Post & Rail Crossbuck 1. Getting Started 6. Crossbuck Be sure to call underground prior to digging Assemble gates (if necessary) and decide where they will be located Stake out the fence line Space and
More informationSteel Casework Metal Framing System
MISCELLANEOUS ITEMS Continuous Slot Metal Framing System Installs quickly Completely adjustable Re-usable Eliminates all welding, drilling and use of special tools G23 METAL FRAMING SYSTEM 1. Place the
More informationDBP Technical Data Series Rev. 0 Jan. 1, Pre Assembled Door Canopies
Technical Data Series Revised: 1 January, 2011 Article IX. SECTION 9.01 PERSONAL DOOR CANOPIES...3 SECTION 9.02 ERECTION INSTRUCTIONS...4 SECTION 9.03 ERECTION ILLUSTRATIONS...7 SECTION 9.04 MULL INSTRUCTIONS
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More information11 6 Round Building Assembly Instructions
11 6 Round Building Assembly Instructions 11 6 Round Building Hardware List 1. Pro Rib Brite White 36 Wide X 68 Long (Siding Steel) 11 2. Top Wall Wheel Ring 3 3. Base Ring 3 4. 1 ½ X 68 Aluminum Tubes
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationFURNITURE LABORATORY METAL FRAMING SYSTEM. For additional information and help in planning contact Mott Manufacturing.
LABORATORY Continuous Slot Metal Framing System For additional information and help in planning contact Mott Manufacturing. G22 Connection Instructions Installs quickly Completely adjustable Re-usable
More informationTELESPAR S I G N S U P P O R T S Y S T E M S
S I G N S U P P O R T S Y S T E M S THE INDUSTRY'S MOST ADVANCED AND COST-EFFECTIVE SIGN-SUPPORT SYSTEM From the smallest village and back road to the largest city and interstate highway, the Telespar
More informationInstallation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationINSTALLATION GUIDE FTX FLOOR Ford Transit ( 148" Extended Wheelbase )
INSTALLATION GUIDE 6540-FTX FLOOR Ford Transit ( 148" Extended Wheelbase ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... 3-4 Phase 2 - Installation q 2.1 Install Preparation... q 2.2 Floor Installation...
More informationMounting the 6 or 12 Indexer on PRS Gantry Tools
Page 1 Mounting the 6 or 12 Indexer on PRS Gantry Tools About this guide: This document illustrates several options for mounting an indexer onto your ShopBot. You can choose the technique that works best
More informationMDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop
500 460 MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop Check if Applicable TRAFFIC SIGNAL SPECIAL DETAILS INDEX/CHECKLIST *One completed checklist required
More information6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)
INSTALLATION INSTRUCTIONS FOR BEDSIDE INNER REPAIR PANELS 67-72 GM FLEETSIDES This instruction illustrates the removal and replacement of the often rusted and damaged lower inner flanges on the 1967-1972
More informationBASEBALL FOUL POLES SURFACE MOUNTED
Page 1 of 5 Installation Instructions 1. 2. Check all items against parts list to ensure all parts have been included. Locate and drill holes for concrete footings. See Details A and B for critical information
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationMidwest Roadside Safety Facility
C 1690" A 42926 75" 1905 150" 3810 G E F F 11 10 9 8 7 6 5 4 3 2 C D D 25 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 21.2 G E Impact 2270P 17 Spaces @ 75" [1905] Spacing = 106' 3" [32385] 1 1662 1/2"
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More information2x Bottom Bracket. 1x Rail Support STEP 1 STEP 2
Level Railing Top Rail Bottom Rail Aluminum Baluster 2x Bottom Bracket 1x Rail Support Kit Includes: 1 - Top Rail (with Baluster Connectors installed) 1 - Bottom Rail (with Baluster Connectors installed)
More information4832A Installation Sheet Part List
4832A Installation Sheet Part List (1) 4016A-43-003 Qty 1- (2) 4016A-43-002 Qty 1- (3) 4016A-43-001 Qty 2- (4) 4016A-10-005 Qty 1- (5) 4016A-43-004L Qty 1- Mounting Bolt Kit (A) (K) Qty 2 - Qty 6 - M10
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationA Captured Fastener, version 1.2
A Captured Fastener, version 1.2 By R. G. Sparber Copyleft protects this document. 1 I needed to be able to fasten two pieces of 16 gage 1" steel tubing together. There shall be no loose parts and no tools
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationINSTALLATION GUIDE N5-DS48-4
INSTALLATION GUIDE N5-DS48-4 Shelving ( steel ) Transit High Roof & Medium Roof Promaster Standard Roof & High Roof Nissan NV High Roof Sprinter Low Roof & High Roof Box Truck / Trailer QUICK START GUIDE
More informationINSTALLATION INSTRUCTIONS
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: 17A110200MSS\17A110200MA MODULAR GRILL GUARD FOR NISSAN FRONTIER 05-10//PATHFINDER 05-07 1 guard, center section 1 brush guard, left side 1 brush guard,
More informationPost & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS
Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM
More information3" SIDEBAR CHEVY TRAVERSE/GMC ACADIA/07-10 SATURN OUTLOOK/07-09 BUICK ENCLAVE (EXCL BUICK ENCLAVE)
PARTS LIST: 1 Driver/Left Sidebar 6 s 1 Passenger/Right Sidebar 6 12mm ID x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting 6 s 1 Passenger/Right Mounting 4 10mm Lock Washers 1 Driver/Left Mounting 4
More informationMidwest Roadside Safety Facility
19'-11 1/2" 6083 239'-11 1/2" 73139 Impact 1100C 25 43 5/16" 1100 upstream from the upstream face of the first shear fender downstream of the joint between barrier nos. 7 and 8 Upstream End Downstream
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD FORD ESCAPE
INSTALLATION INSTRUCTIONS GRILLE GUARD 08-010 FORD ESCAPE PARTS LIST: 1 Grille Guard 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Frame Mounting 4 10mm Lock Washers 1 Passenger/Right Frame Mounting 6 10mm
More informationLeveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationINSTALLATION INSTRUCTIONS
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART # RN-FOF1SCC-09-91 CUTLASS RUNNING BOARDS PARTS LIST: 5 STAINLESS AND ALUMINUM SIDEBARS 2 Left or right Sidebars 10 8-1.25mm x 30mm Hex Bolts 2 Driver/Left
More informationDisplay/Accessory Furniture
1 Multimedia Display End-of-Range, 60-013-S00 End-of-range displayer has five 59 1 /2" 19 3 /8" 16" 163 Sloped Shelving Book Displayer sloping shelf spaces for displaying books spine out at an angle for
More informationNOTES: 4" OVERHANG MAX. (TYP) DETAIL N (SHEET 13)
L " X " X " L " x " x " DETAIL J GUSSET - '-" L " X " X " TRUSS SAN (FT) 50 L L2 (FT) (FT).5 5 TRUSS DATA L CAMBER (FT) (IN).5 5/ ESTIMATED BOX TRUSS WEIGHT (LBS/FT) '-0" x - LAN TO WIND BRACING LOOKING
More informationB " 787
175'0" 53339 3H:1V S.B.P. 25" 635 3H:1V Slope 100'0" 30480 Soil Cut 3H:1V Slope 58" 1474 75" 05 1 2 3 4 5 6 7 8 9 10 11 12 13 25 14 15 16 17 18 20 21 22 23 24 25 2270P Impact 243 60 12 Spaces @ 75" [05]
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationCENTER WING SECTION (CWS) WORK REPORT
CENTER WING SECTION (CWS) WORK REPORT No. Check Parts / Description Qty PHASE 1: Preparations 1 [ ] 6V1-3 Rear ribs 2R & 2L 1 [ ] L Angle 6 2 [ ] 6V2-1 Rear Ribs.032 2R & 2L 2 [ ] 6V5-1 Gear Rib Doubler
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationDouble Beam Freestanding Pergola Installation Guide
Double Beam Freestanding Pergola Installation Guide Patent Pending. Copyright 2011 USAVinyl, LLC - All Rights Reserved The information contained in these instructions are proprietary to USAVinyl, LLC and
More informationAllow 60 from door face
Setbacks Allow 60 from door face TOOLS NEEDED Tape Measure Marker or Pencil Masonry Drill Bit 3/8 Hammer Drill Hammer Socket Wrenches and Wrench: 9/16, 1/2, 7/16, 1/4 drive socket wrench and 1/2 socket
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More information96 (Standard Length)
Setbacks 96 (Standard Length) Bike Files may be lined up end to end to fill the available space. A 36 aisle should be left between the ends of bikes in racks facing one another. 36 aisle 50 Installation
More informationOwner's Manual & Assembly Instructions
Owner's Manual & Assembly Instructions PK01 BASE KIT Model No. FDN106 71706011 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE,
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationCURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START
ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction
More informationSECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationDoor Canopy. PDL Building Products Industrial Parkway, N. Olmsted, OH Phone:
Door Canopy Door Canopies are attractive and efficient while eliminating the need and expense of drafting and manufacturing canopies as part of the building package. Construction: 26 gauge material around
More informationHaukaas Bale Rack Kit
Page 1 Haukaas Bale Rack Kit For hauling large round bales "Pipe Style". C D Pocket Reinforcement Plates 10" 11" A: Pocket Side Plate B: Pocket Top Plate C: Side Stake D: End Stake E: Floor Plate B A F:
More information10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2
PARTS LIST: 3" ROUND SIDEBARS 1 Driver/Left sidebar 4 12mm x 32mm OD x 3mm Flat Washer 1 Passenger/Right sidebar 4 12mm x 24mm OD x 2.5mm Flat Washer 1 Driver/Left Mounting Bracket 6 12mm Lock Washers
More informationMechanical System Specifications & Detail Drawings
Mechanical System & Detail Drawings 1-888-989-1370 www.lundiausa.com RECOM GROUP INC. 449 Borrego Court San Dimas, CA 91773 Phone: (909) 599-1370 Fax: (909) 599-2291 MECHANICAL SYSTEM SPECIFICATIONS All
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationINSTALLATION GUIDE Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum )
INSTALLATION GUIDE 7115 Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Locker w/ Top Shelf Assembly... 3-5 6-13 Phase
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More information8mm x 25mm "Z" Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Side Frame Mounting Bracket 8 12mm Hex Nuts 1 Passenger/Right Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Driver/Left
More informationSection Member. H (in.) WT. lb./ft. Pull Out Strength Slip Resistance Torque Size / Thread All Series
Design Data Channel TABLE 1 Elements of Sections Properties for Design Single Channels Nominal Thickness (inches) ga = 0.105 ga = 0.075 16 ga = 0.060 Double Channels LEGEND I Moment of inertia S Section
More information10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2
PARTS LIST: 1 Driver/Left sidebar 4 12mm x 32mm OD x 3mm Flat Washer 1 Passenger/Right sidebar 4 12mm x 24mm OD x 2.5mm Flat Washer 1 Driver/Left Mounting Bracket 6 12mm Lock Washers 1 Passenger/Right
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationMODEL AL-HD & AL-HDM INSTALLATION INSTRUCTIONS
& AL-HDM INSTALLATION INSTRUCTIONS 12U AND NUT EXPOSED SURFACE CONTINUOUS EXTRUDED ALUM. SERRATED COVER PLATE CONTINUOUS EXTRUDED ALUM. STYROFOAM BACKER AND CAULKING OPTIONAL WATERSTOP CONTINUOUS EXTRUDED
More informationMidwest Roadside Safety Facility
B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized
More informationINSTALLATION INSTRUCTIONS
TEL -866-XANATOS INSTALLATION INSTRUCTIONS PART#: 7D5000SS\7D500A GRILL GUARD FOR DODGE SPRINTER 07-09 PARTS LIST: 8 6 Grille Guard Driver/Left Frame Mounting Passenger/Right Frame Mounting Driver/Left
More informationHeartland Perma-Column 1841 E 1450 Rd. Lawrence, KS (785)
141 E 1450 Rd. Lawrence, KS 66044 (75) 594-5696 Perma-Column Installation Instructions i Unlike any other concrete post-frame foundation system, Perma-Column Precast Concrete Piers use 10,000 psi concrete
More information10 x 10 Flat Top Pergola
0 x 0 Flat Top Pergola A S S E M B L Y G U I D E Models: Venetian, Tuscany, Luxor, Acadia O P T I O N A L A C C E S S O R I E S Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post)
More informationFree Standing Frame and Canopy
Patriot Docks Free Standing Frame and Canopy Required Tools: Cordless Drill, 3/8 drill bit, 17mm wrench, 18mm wrench, 6mm hex key (included), 8mm hex key (included) Helpful Tips: Assembling and installing
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More information24" B B Joint X501 Joint See MARKINGS Note PCB-RXX-350-TL3 " X501 Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOT
B B Joint Joint See MARKINGS Note PCB-RXX-350-TL3 " Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOTES GENERAL: This barrier may be manufactured with reinforcing steel
More informationD.O.T. Bullet/Bicycle Rail System - Certs Available upon request
D.O.T. Picket Rail - Certs available upon request prior to ordering Top and Bottom Rail: 18-61-240 2 SCH 40 Pipe x 20-2-3/8 x 2.067 x.154 1.264 18-61-241 2 SCH 40 Pipe x 24-2-3/8 x 2.067 x.154 1.264 18-61-243
More informationCAT-350 Product Manual
CAT-350 Product Manual Release 01/17 www.ingalcivil.co.nz CAT-350 NZ Assembly Manual Ingal Civil Products NZ 40 Tironui Road, Auckland 2112 www.ingalcivil.co.nz Important: These instructions are for standard
More informationSTANDARD GRAVITY BOX TARP INSTALLATION
OPERATORS MANUAL Rev. 9.9.2016 STANDARD GRAVITY BOX TARP INSTALLATION J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.com
More informationSpiral Slide
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationVinyl Fence Products. Installation Guidelines. Hyde Park with H-Post Fence
Vinyl Fence Products Installation Guidelines Hyde Park with H-Post Fence Hyde Park with H-Post Privacy Fence 1. Getting Started Be sure to call underground prior to digging Assemble gates (if necessary)
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationAssembly Instructions
Laminate/Phenolic & 1 Pc Butcherblock Tops Before you begin, please make sure all parts and proper quantities are included. (See on next page) Any parts damaged during shipment must be reported within
More information8 x 8 Flat Top Pergola
A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit Models: Mirage, Mandalay Ver 6/00 Ta b l e o f Co n t e n t s Introduction & Overview......................................................
More information(2) 25mm x 20mm x 5mm Adhesive Backed Foam Pads. 100mm x 50mm x 1.0mm Adhesive Backed Foam. (2) Spacer Plates. Passenger/Right Side Frame Mounting
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Frame Mounting 16 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting 8 12mm Hex Nuts 1 Driver/Left Side Top Support 2 10-1.50mm
More information