Heat Exchanger Coil: Build Instructions
|
|
- Dominic Lee
- 6 years ago
- Views:
Transcription
1 Heat Exchanger Coil: Build Instructions
2 Tank Assemblies Feed Tank (Drawing: WS-101) o Use a jig-saw to cut a large circle into the top of the barrel, 2-3 inches in from the edge o Leave the lip intact. Feed Tank Valve Assembly o Using a cordless drill, Drill 1/2 hole 3 inches up from the bottom of the feed tank. o Insert the ½ conduit hub (Drawing: WS-103) into the hole and secure with plyers. o Cover the threads of the ½ x 3 pipe nipple (Drawing: WS-106) with plumbers tape and thread into the conduit coupler. o Thread the ½ Brass Ball Valve (Drawing: WS-105) onto the pipe nipple. o Cover both threads of the ¾ Hose to ½ Pipe (Male) Thread Adapter (Drawing: WS-112) with plumbers tape. o Thread in the larger side into the ball valve. Output Tank o Use a jigsaw to cut a square hole from the top of the barrel o Drill a 1/2 hole into the side of the barrel about 3. This is for the input hose.
3 Output Hose Bib (Drawing: WS-312) o Drill a ¾ hole on the opposite side of the previous hole, about 3 above the ground. o Thread the hose bib into the hole. o Hand tighten all the way. Bending Copper Coil (Rough In) Turn Kon-Tiki kiln up-side-down on a flat surface. Mark half-way up on the outside of the Kon-Tiki with tape or marker. Measure 50 on one end of the coil, and 45 on the other end. Mark this point with tape. These sections will be bent differently to form the input and output of the helix. Have one person hold one end of the coil in place at the half-way mark. Have the other person holding the rest of the coil walk slowly around the Kon-Tiki, bending the pipe around the diameter of the kiln. The person holding the pipe to the kiln will need to rotate around the kiln with the second person to continuously hold the bending coil in place.
4 Try to keep your coil at the half-way mark. This is to maintain a size close to the final required diameter. After entire coil is bent remove the coil from the Kon-Tiki. (This may require you to remove one of the legs). Silver Solder Copper Brazing Input and Output Diffuser Assembly o Cut 3 length of ½ schedule L copper straight pipe (Drawing: WS-109). o Braze the ½ Male Copper Adapter (Drawing: WS-108) to one end of the copper pipe. o Braze the copper ½ 3/8 Copper Reducer (Drawing: WS-110) to the other end of the copper pipe o Braze this combination of parts to the end of Copper Coil (Drawing: WS-202) Use high temp flux to prep all couplings Use high temp silver solder to braze all couplings o After connections are cool, wrap male copper pipe thread coupling with plumbers tape.
5 Support Triangles (Drawing: WS-203) Measure and cut two 5 x 5 aluminum sheet metal squares Measure and mark out center-point holes along the diagonal in accordance with the drawing Use a riser block, clamps, and a 45 deg. triangle to set up both squares on the vertical mill Use a 5/8 diameter mill tool to cut the oval shaped holes Use a 0.1 diameter drill bit to cut holes for the wire. Drill ¼ holes as for support bolts
6 Remove each square from the mill and cut in half down the center-line with a band saw Support Bars Cut a 6 ft length of 1 x 1 steel bar (Drawing: WS- 201) Drill a 1/4 hole all the way through the bar from either end of the bar (2 holes) On one side of the bar, increase the ¼ hole to a ½ hole to allow for the bolt head. Cut two 15 lengths of 1 x 1 bar Use the vertical mill to make the 1 and 4 cuts shown in (Drawing: WS-204) There are multiple ways to do this but the method used was to use the mill to make the initial cut down the length of the bar. Then flip the bar and remove the flap created at the desired length. Drill 1/4 holes in the locations shown in (Drawing WS-204)
7 Support Assembly (Drawings: WS-201, WS-203, WS-204) Bolt together the support bars Bolt together the support triangles to the support bars Bending Coil (Final) (Drawing: WS-200) Put support bar structure up-side-down on a flat surface. Place entire coil over the support bar structure. Start at the end of the copper pipe with the 50 measurement. Place this end of the copper pipe into the uppermost slots (smallest diameter helix).
8 Tie the pipe into the slot with copper wire. This is tricky but do you best to make it as tight as possible. Attach the other two support triangles using the copper wire. o Use a tape measure to make sure the diameter of the smallest coil is about 23 Continue this process until the entire coil is attached to the support triangles. (Teamwork is advised) The best way to make a concentric helix was found to have people pull on the pipe from opposite sides. Doing this repetitively while rotating around the helix allowed for a nice circular shape as well as equal spacing. Thermostat Housing (Drawings: WS-302, WS-303) Cutting Blank Stock to Length o Use DoAll machine to cut one 6.5 and one 5.5 section of aluminum from the blank stock Sections are 2 longer than needed so the chuck teeth of the lathe has enough space to grip specimen o De-burr cut edge of each specimen o Wash the cut sections with soap and water to remove lubricant and burrs
9 Turning of Outlet Side (Drawing: WS-303) o Place 5.5 specimen into lathe chuck and tighten o Using the lathe, face the outer surface of the housing to make a uniform/flat surface o Use a starter tool to put an initial hole into the center of the specimen o Use a 3/8 bore tool to bore into specimen 1.5 o Use die to thread 3/8 hole with ½-14 NPT straight pipe tapered thread o Use a cutting tool to reduce the outside diameter of 2.25 of the specimen from 3 to 2 diameter o Using a band saw, remove 2 of length from the specimen o Use a starter tool to put an initial hole into the center of the specimen o Use a 1.5 bore tool to bore out into specimen 1.5
10 Turning of Inlet Side (Drawing: WS_302) o Place 6.5 specimen into lathe chuck and tighten o Using the lathe, face the outer surface of the housing to make a uniform/flat surface o Use a starter tool to put an initial hole into the center of the specimen o Use a 3/8 bore tool to bore into specimen 1.5 o Use die to thread 3/8 hole with ½-14 NPT straight pipe tapered thread o Use a cutting tool to reduce the outside diameter of 3.25 of the specimen from 3 to 2 diameter o Remove specimen from chuck and rotate 180 deg. Re-attach chuck to the 2 diameter part of the specimen o Using a cutting tool, remove 2 of length from the specimen o Use a starter tool to put an initial hole into the center of the specimen o Use a 1.5 bore tool to bore out into specimen 2.5 o Use a cutting tool to create a 2.11 diameter hole of depth.083 in flange face Output Hose a. Attach the hose to the Copper Male Threaded Adapter (Drawing: WS-309) i. Use hose clamp to assure secure connection b. Wrap plumbers tape around male threads of coupling
Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationLocoGear. Technical Bulletin - 14 November 28, 2003 Copyright 2003 by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 14
LIVE STEAM CASTINGS LocoGear Tech Bulletin - 14 John D.L. Johnson 3879 Woods Walk Blvd Lake Worth, FL 33467-2359 jjohnson@locogear.com www.locogear.com Technical Bulletin - 14 November 28, 2003 Copyright
More informationClocking a TD-04 Turbo Compressor Housing. Appendix A : AWIC Silicone and Tubing Fitting
Clocking a TD-04 Turbo Compressor Housing Appendix A : AWIC Silicone and Tubing Fitting Revision A: 7-13-2015 Tools: Metric Sockets (10, 12, 14, 17mm) 5mm Hex Key Large Internal Snap Ring Pliers 3/8 Socket
More informationBuilding Rudy Kouhoupt s Walking-Beam Engine
Building Rudy Kouhoupt s Walking-Beam Engine Some time ago I came across a copy of Rudy Kouhoupt s article: "Build this Walking-Beam Engine" (Popular Mechanics August 1969), and decided to try and make
More informationMachine Your Fishing Reel
Machine Your Fishing Reel You will be well prepared for the coming season if you start on this smooth-running job now. IF you're an enthusiastic fisherman and have a lathe in your workshop, we'll say no
More informationPlumbing Part II - Hand Pump
Plumbing Part II - Hand Pump Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 7/17/03 Last Revised: 06/06/2004 The hand pump located in the tender water tank is a backup pump should the axel pump fail
More informationCross Peen Hammer. Introduction. Lesson Objectives. Assumptions
Introduction In this activity plan students will develop various machining and metalworking skills by building a two-piece steel hammer. This project will introduce basic operations for initial familiarization
More informationReversing Gear. Shay Reversing Gear
Shay Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 9/23/03 Last Revised: 06/05/2004 The reversing gear is another one of those pieces I've been putting off. The reason for the postponement was that
More information2 Cylinder Slidevalve Steam Engine
2 Cylinder Slidevalve Steam Engine By Thor Hansen After making a slide valve engine that I managed to get running I decided to try and make a 2-cylinder version. Since the first one was a vertical steam
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationPURESTREAM SYSTEM - ASSEMBLY GUIDE
PURESTREAM SYSTEM - ASSEMBLY GUIDE VISIT OUR WEBSITE : www.cagpurification.com our installment procedure videos in the PURESTREAM Piping section. NECESSARY TOOLS FOR INSTALLATION We suggest the use of
More informationType 316SS Backed Conveyor Strip Brush Nylon Bristles, 6" O'all HT, 2' Lg, 3/16" Backing
How to modify your MK101. First off, the MK101 tile saw is a fantastic tile saw, without any modifications what so ever. That being said, all tile saws tend to have a significant amount of overspray which
More informationMINI-LATHE QUICK CHANGE TOOL POST
MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here
More informationThe Virgo/Libra Steam Engine
The Virgo/Libra Steam Engine Congratulations on becoming the owner of a Virgo or Libra Steam Engine. With careful use and maintenance it will give many years of satisfying performance. Contents 1) Notes
More informationA SRF/SERF A SRF/SERF
A1100-055SRF/SERF A1100-056SRF/SERF Remote Fill Assembly INSTALLATION INSTRUCTIONS **CRITICAL - MUST READ** This unit can only be used for new installations or tank level retrofits that allow access to
More informationTravis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)
Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach
More informationAcrylic Claw Foot Tub
Acrylic Claw Foot Tub Wrench or socket Drill & Bits Parts Recommended 2-2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re-inforce the floor before securing tub. We recommend 2-2 x12 s securely fastened
More informationAssmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS
Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS General Information Assmann polyethylene storage tanks are manufactured to give you the toughest, most reliable
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationTHREAD CUTTING & FORMING
THREAD CUTTING & FORMING Threading, Thread Cutting and Thread Rolling: Machining Threads on External Diameters (shafts) Tapping: Machining Threads on Internal Diameters (holes) Size: Watch to 10 shafts
More information(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) DODGE RAM 1500 QUAD CAB PART #DZ /DZ /DZ /DZ
(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) PART #DZ 372231/DZ 372233/DZ 372237/DZ 372239 PARTS LIST: 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) Qty Description Qty Description
More informationONASSIS SHOWER SET INSTALLATION
SKU(s): 925939 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationT : F : Revised June 2013
Revised June 2013 W R A, O USA T: 800 321 7950 440 998 2788 F: 440 992 2925... 2 INSTRUCTIONS FOR 3/4, 1, 1-1/4 DIAMETER TAPS FIGURE 1 A B C D E F G HOT TAP SPINDLE HOT TAP SLEEVE HOT TAP FEED SCREW ADAPTER
More informationLegacy Classic Twist Pencil Kit
Legacy Pencil Kit Description: The pencil is great kit and has features to make it a step-up pen. It is slightly more difficult to make, but still very easy if you follow these instructions carefully.
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationVertical Steam Engine from barstock
Vertical Steam Engine from barstock By Thor Hansen After having built several small oscillating steam engines and Rudy Kouhoupt s Walking Beam engine I decided to have a go at a slide valve engine. My
More informationRorty No.2 Tube Bender.
Copyright. This entire Manual is copyrighted to Rorty Design, with all rights reserved. No part may be transferred or copied by any means whatsoever, without the express written permission of Rorty Design.
More informationShay Drive Shafts & Universal Fabrication
Shay Drive Shafts & Universal Fabrication Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 5/22/03 Last Revised: 06/06/2004 The following describes how I machined the universal rings and drive shafts.
More informationw w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models
-J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationExploration of a Student Project in a Materials Processing Course
Paper ID #8093 Exploration of a Student Project in a Materials Processing Course Prof. Somnath Chattopadhyay, Georgia Southern University c American Society for Engineering Education, 2013 EXPLORATION
More informationBuilding a vertical wobbler
Building a vertical wobbler I wanted to build a simple steam engine that would also run on compressed air. At Chris Heapy s website (http://easyweb.easynet.co.uk) I found drawings of a small double acting
More informationName Hour Course Jewelry/A. Brass Tile Sampler. (use the metal cutter press or hand shears / tin snips)
Jewelry/A Intro: Brass Tile Sampler How do jewelers refine their skills in order to make complex and unique work? The work you do throughout these assignments and units will be the stepping stones for
More informationCALLAS THERMOSTATIC SHOWER SET
SKU(s): 925945 CALLAS THERMOSTATIC SHOWER SET BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationAutomated Tiki Torch Installation Instructions
Automated Tiki Torch Installation Instructions Automated Tiki Torch with Poles (Exploded View) 14 Automated Tiki Head 6 8 Tiki Pole (Powder Coated Aluminum or Faux Bamboo Pole) 12 Base Pole (Powder Coated
More informationLegacy Slimline Pencil Kit
Description: The model is considered one of the most basic pen kits and is a great starter kit for those new to pen turning. Many experienced pen turners use the kit to make elaborate and unusual pens
More informationB-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
More informationInstruction Sheet MCHE 365 & I-Tech 344 Lathe & Mill Machining Operations Pencil Organizer Project, FALL 2015
Instruction Sheet MCHE 365 & I-Tech 344 Lathe & Mill Machining Operations Pencil Organizer Project, FALL 2015 1 Always flip to 1 st page & leave your drawings & instructions on your Machine at end of class.
More informationChapter 23 Drilling and Hole Making Processes. Materials Processing. Hole Making Processes. MET Manufacturing Processes
MET 33800 Manufacturing Processes Chapter 23 Drilling and Hole Making Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Materials Processing
More informationInstallation Instructions
MOUNT TUB SYSTEMS HAMPTON TRIM KIT T980.702 Installation Instructions T980.702 T980.712 T980.722 T980.732 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
More informationToyota 4 Runner and Lexus GX Skid Plate installation instructions.
Toyota 4 Runner and Lexus GX Skid Plate installation instructions. NOTE: When installing the full set of skid plate start at the rear of the vehicle and work your way forward. NOTE: Torque Specs: Tighten
More informationAMETAL SHAPER is indispensable for certain METAL SHAPER FOR YOUR SHOP. By S. S. Miner
METAL SHAPER FOR YOUR SHOP By S. S. Miner AMETAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationFlat file. Round file. Hand file. Half -round. Mill file. Square file
Name Picture Cross section Uses: Cut pattern:: Hand file used for roughing and finishing. It has double cut teeth on two faces, single cut teeth on one edge, and one safe edge Flat file used for roughing
More informationPresentation prepared By Andrea Thomas, Texas and Arkansas Master Gardener, Plant Propagation Specialist
Presentation prepared By Andrea Thomas, Texas and Arkansas Master Gardener, Plant Propagation Specialist The water from a rain barrel is nonpotable (not drinkable), but it has several practical uses such
More information50, ,000 18,800 8,000. CODE 04 ER (ER ) UPC Chuck/W ITS Central Chuck. CODE 04 ER (ER ) UPC Pallet For Alignment
CODE 04 ER-007826 (ER-017777) UPC Pallet For Alignment CODE 04 ER-007823 (ER-016092) UPC Chuck/W ITS Central Chuck Application To align angular position and to determine the center of UPC chucks. Please
More informationSERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO
47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small
More informationDATE: January, 01, 2011 AUTHOR: Craig Macomber TOPIC: Making and operating a model onager
DATE: January, 01, 2011 AUTHOR: Craig Macomber TOPIC: Making and operating a model onager INTRODUCTION This guide will walk you through the construction and operation of a hand held scale Roman Onager,
More informationPrepare Base Assembly. (If pump is pre-assembled on base, go to step#8.)
F L Instructions Maxim 3000 Turbo Flush Installation INTRODUCTION Satellite portable restrooms and accessories must be assembled according to approved assembly procedures. Avoid variations in assembly
More informationTHE PROCESS OF PRODUCING P-5678 SPRING PINS FOR NORTHLAND TRUCKS
THE PROCESS OF PRODUCING P-5678 SPRING PINS FOR NORTHLAND TRUCKS Prepared For Don Klepp, English 132 Instructor Okanagan University College By Richard Pelletier Mechanical Engineering Technology 1 Okanagan
More informationConstruction Manual for High Altitude Test Chamber
Construction Manual for High Altitude Test Chamber Howard L. Brooks, Principal Investigator Department of Physics and Astronomy DePauw University Greencastle, IN 46135 hlbrooks@depauw.edu 6 January 2014
More informationINSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B
INSTALLATION INSTRUCTIONS PART NUMBER SB1214S SB1214B PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Sidebar 4 12mm Lock Washers
More informationD E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L metalwork processes Screw Threads The screw thread is a very important detail in engineering. It is used to hold parts together.
More informationCredit Value 10 QCF Level 3 GLH 75. Learner pack
QETA/046 Advanced milling Credit Value 10 QCF Level 3 GLH 75 Unit purpose/aims Learner pack This unit enables you to acquire the skills and essential background knowledge relating to advanced milling techniques,
More informationTypical Parts Made with These Processes
Turning Typical Parts Made with These Processes Machine Components Engine Blocks and Heads Parts with Complex Shapes Parts with Close Tolerances Externally and Internally Threaded Parts Products and Parts
More informationTraditional Wall Mounted Potfiller
TOOLS NEEDED FOR INSTALLATION 1/4 hex wrench (provided in installation kit) 3/32 hex wrench (provided in installation kit) Pencil or marker PTFE tape Small level, or carpenters square Power Drill with
More informationKossel Rev B Build Guide V1.0
Kossel Rev B Build Guide V1.0 1 Table of Contents: Step 1: BASE ASSEMBLY Gathering parts: Building the Corners and Base: Step 2: UPPER ASSEMBLY Building Upper: Step 3: VERTICAL RAIL INSTALLATION Building
More informationEXIRA SHOWER SET INSTALLATION
SKU(s): 925470 EXIRA SHOWER SET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationwww.wildmanconstruction.com Changing your toilet is an easy project that should take half a day or less. The most common toilet has a separate tank that mounts on top of the bowl. These instructions apply
More informationScratch Built: Live Steam Garratt
Scratch Built: Live Steam Garratt BY Bill Allen Woodside, CA. USA (Live Steam/Topic: Garratt build photos) (Live Steam/Topic: Garratt Photos Boiler & Cab Construction) (Live Steam/Topic: Tools & Gizmos
More informationTool & Cutter Grinder
Tool & Cutter Grinder The Bonelle Tool and Cutter grinder (based on prof. Chaddock s Quorn) can be used to grind most kind of tools from lathe tools to end-mills and reamers. I have been grinding my end-mills
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationWOOD TOY NEWS. July 23, 2013 Tuesday
WOOD TOY NEWS Make your own perfect turntable for spray painting toys with these useful tips. And it s fast, fun and easy to build! by Imants Udris Watch the video on our website at : http://www.toymakingplans.com/website/how-to/
More information4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back
HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation
More informationINSTRUCTIONS
IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR
More informationClock 35 - Toyland. Construction instructions for Clock 35
This clock has been designed for children, it is a stand-alone unit and can be positioned on a shelf or cabinet out of the reach of very young hands who may be tempted to touch. The clock is shown in two
More informationBEAST THE. Tube and Pipe Notcher Operating Instructions. Notches In Bends Straight Notches. Angled Notches. Offset Notches
Copyright (c) 2007 J D SQUARED INC. www.jd2.com THE BEAST Tube and Pipe Notcher Operating Instructions Notches In Bends Straight Notches Angled Notches PATENT PENDING Offset Notches Assembly After unpacking
More informationno mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side
Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable
More informationVacuum Chuck System How I Built Mine
Vacuum Chuck System How I Built Mine While there is a lot of info on the subject of vacuum systems that can be located on the various forums, not many walk you through the process of putting one together.
More informationRiser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8
Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18 Manual 40100X35-8 3 2 4 Access covers with bolts supplied with Interceptor 1 5 14 6 11 15 Sampling Port/Cleanout cap supplied with Interceptor 12
More informationInstruction Manual for MHE Products DeepWater2 PushPoint Sampler Ver. 2.0 November 21, 2016
Instruction Manual for MHE Products DeepWater2 PushPoint Sampler Ver. 2.0 November 21, 2016 The DeepWater2 is heavier-duty a version of the PushPoint Sampler made of stainless steel pipe instead of SS
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationBend-Tech Dragon Assembly Manual
p.1 Bend-Tech Dragon Assembly Manual IMPORTANT: Please read before unpacking. Place shipping container in a wide open area where you will have room to work and assemble this product. Shipping The Dragon
More informationOutdoor Cooler Cart. Outdoor Cooler Cart Construction Instructions
Outdoor Cooler Cart Outdoor Cooler Cart Construction Instructions Make the Legs and Side Panels. Cut the eight long and short leg pieces to length. See Material List on next page.. Apply a bead of glue
More informationWork Space Set-up. Slats will level the pipe during bending and help minimize twisting of the bow.
Work Space Set-up Affix pipe bender to end of working surface Slats will level the pipe during bending and help minimize twisting of the bow. Make the slat height equal the distance from your work surface
More informationHow is vacuum measured? Vacuum is measured in inches of mercury. Our atmosphere will support a column of mercury 30 inches tall.
This document assumes the person attempting to make and use a vacuum chuck has a working knowledge of various power tools, hand tools, and wood lathes. There are NO safety warnings contained within. If
More informationChapter 23. Machining Processes Used to Produce Round Shapes: Turning and Hole Making
Chapter 23 Machining Processes Used to Produce Round Shapes: Turning and Hole Making R. Jerz 1 2/24/2006 Processes Turning (outside surface) straight, taper, facing, contour, form, cut-off, threading,
More informationName: Class: Teacher:..
Name: Class: Teacher:.. 1 Metals All metals in use today are either PURE METALS or ALLOYS. Copper, iron, tin, lead, gold and silver are all examples of PURE METALS which have been mined from the Earth
More informationSECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationLegacy Polaris Pen Kit
Description: The Polaris model is a single tube pen kit that uses a 3/8 tube and is a great starter kit for those new to pen turning. They look similar to our Viceroy kit but the body tube is longer which
More informationAD5X. Low Cost HF Antennas & Accessories. Phil Salas - AD5X Phil Salas AD5X. Richardson, Texas
Low Cost HF Antennas & Accessories Phil Salas - AD5X ad5x@arrl.net PVC Tubing PVC pipe: Considers the inside diameter (ID) of the pipe. For PVC pipe (schedule 40): 1/2" PVC pipe has an ID of 0.6" and an
More informationPlans for The Siamese Twins
Plans for The Siamese Twins Requests have been pouring in for plans for the Siamese Twins. In fact, another one poured in just last week! So I ve spent the past several days drawing them up. I think it
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationKerkau Manufacturing. B16.5 Flange Book
Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions
More informationThe Ultimate Guide To Creating A Wind Turbine
The Ultimate Guide To Creating A Wind Turbine DISCLAIMER These guides and videos have been designed to help others to help create alternative energy by showing how to create a wind turbine. Every effort
More informationIntroduction to Machining: Lathe Operation
Introduction to Machining: Lathe Operation Lathe Operation Lathe The purpose of a lathe is to rotate a part against a tool whose position it controls. It is useful for fabricating parts and/or features
More informationThe Kruger Eccentric
The Kruger Eccentric Instructions for Use of the Dual Taper Reel Seat Filler and Eccentric Reel Seat Recess Turning Mandrels Rick Kruger 503-860-6346 krugerr@easystreet.net The Dual Taper Reel Seat Filler
More informationLegacy Upgraded Junior Gentlemen s Pen Kit
Description: The Upgraded Junior Gentlemen s model is a classic style pen which is easy to turn and uses a Roller Ball Refill which is highly desirable among pen enthusiasts The Upgraded Junior Gentlemen
More informationWater Rocket Launcher
Rocket Activity Water Rocket Launcher Objective Construct a launch platform for launching water rockets. National Science Content Standards Physical Science Position and motion of objects Motions and forces
More informationSTEEL RULE. Stock TRY SQUARE
FITTING INTRODUCTION Fitting consists of a handwork involved in fitting together components usually performed at a bench equipped with a vice and hand tools. The matting components have a close relation
More informationAn Improved Tool Support for a Harbor Freight Tool Grinder, version 2.2
An Improved Tool Support for a Harbor Freight Tool Grinder, version 2.2 By R. G. Sparber Copyleft protects this document. 1 Advisory This article was written with a hobby machinist a bit above novice in
More informationDue to possible damage in shipping, the vertical stop assembly has been removed from this machine.
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four
More informationPCS. Patient Security Service Console. Installation Instructions.
www.hsiheadwals.com PCS Patient Security Service Console Installation Instructions Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com Hospital Systems Inc. 750 Garcia Avenue Pittsburg CA 94565
More informationFig2: The Sliding Glue Block from the back.
Ornament Stand Introduction It was one of those forehead smacking moments. I was taking the #2 jaws off my Stronghold chuck, to put on my homemade wooden two jaw chuck set-up. For some reason instead of
More informationI FOOT. ={Li..W---- r"-l, : I t- JJl --, : I: +- y1a'_' L 1~6~'1. ' +-+-'-f' <~,~ ::-,-~,~-~--f~:,~::-~%r
1hz" 3/Is"m.p.1. +--1---4+ ; ttf. I I, /~ 'r-- - - - - - - - - - - -1-11--- -- ---(~/-+--':.r--+~ ' +-+-'-f'
More information6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)
INSTALLATION INSTRUCTIONS FOR BEDSIDE INNER REPAIR PANELS 67-72 GM FLEETSIDES This instruction illustrates the removal and replacement of the often rusted and damaged lower inner flanges on the 1967-1972
More informationMiniature Steam Pty Ltd (Incorporating Live Steam Supplies)
Miniature Steam Pty Ltd (Incorporating Live Steam Supplies) Materials List 28 May 2013 The attached listings outline products we offer and their retail prices as at the above date. We reserve the right
More informationw w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models
-J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationProcedure for Longworth Chuck construction
Procedure for Longworth Chuck construction Overall construction The Longworth chuck is composed of three major components. Connected to the lathe spindle is some device that fastens to the first of two
More informationSkybolt V2 Construction Manual
Skybolt V2 Construction Manual Property of www.ppgplans.com Do not duplicate or make public. Warnings & Disclaimers. This product shows how to build a basic frame only for Powered Paragliding. It is the
More information