Security Fasteners: Furnish not less than one box for every 50 boxes or fraction thereof, of each type and size of security fastener installed.

Transcription

1 SECTION DETENTION DOORS AND FRAMES PART 1-GENERAL 1.1 SUMMARY A. Section includes detention doors and frames. B. Related Requirements: 1. Section "Special Project Procedures for Detention Facilities" for general requirements for detention facilities. 1.2 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: In addition to plans, elevations, sections, and attachment details, provide a schedule using same reference numbers for details and openings as those on Drawings. 1.3 INFORMATIONAL SUBMITTALS A. Product test reports. 1.4 MAINTENANCE MATERIAL SUBMITTALS A. B. Security Fasteners: Furnish not less than one box for every 50 boxes or fraction thereof, of each type and size of security fastener installed. Tools: Provide two sets of tools for installing and removing security fasteners. 1.5 DELIVERY, STORAGE, AND HANDLING A. B. c. Deliver detention hollow-metal work palletized, packaged, or crated. Do not use nonvented plastic. Deliver welded detention frames with two removable spreader bars across bottom of frames. Store detention hollow-metal work vertically under cover at Project site with head up. Place on minimum 4-inch- (102-mm-) high wood blocking. Provide minimum 1/4-inch (6.3-mm) space between each stacked door. DETENTION DOORS AND FRAMES

2 PART 2 -PRODUCTS 2.1 MANUFACTURERS A. Subject to compliance with requirements, provide products by one of the following: I:nl sbi_li. B. Source Limitations: Obtain detention doors and frames from single source from single manufacturer. 2.2 DETENTION DOOR AND FRAME ASSEMBLIES A. Detention Door and Frame Assemblies: ASTM F 1450 for security grades specified. B. Detention Frames: Comply with ASTM F 1592 and removable stop test according to NAAMM HMMA DETENTION DOORS A. General: Provide flush-design detention doors of seamless hollow construction, 2 inches (51 mm) thick. Construct detention doors with smooth, flush surfaces without visible joints or seams on exposed faces or stile edges. B. Core Construction: Provide the following core construction of same material as detention door face sheets, welded to both detention door faces: 1. Steel-Stiffened Core: inch- (1.0-nnn-) thick, steel vertical stiffeners extending fulldoor height, with vertical webs spaced not more than 4 inches (102 mm) apart, spot welded to face sheets a maximum of 3 inches (76 mm) o.c. Fill spaces between stiffeners with insulation. C. Vertical Edge Channels: inch- (3.1-mrn-) thick, continuous channel of same material as detention door face sheets, extending full-door height at each vertical edge; welded to top and bottom channels to create a fully welded perimeter channel. D. Top and Bottom Channels: inch- (3.1-mrn-) thick metal channel of same material as detention door face sheets, spot welded, not more than 4 inches (1 02 rnm) o.c., to face sheets. 1. Reinforce top edge of detention door with inch- (1.3-mm-) thick closing channel, welded so channel web is flush with top door edges. E. Hardware Reinforcement: Fabricate reinforcing plates from same material as detention door face sheets to comply with the following minimum thicknesses: DETENTION DOORS AND FRAMES

3 1. Full-Mortise Hinges and Pivots: inch (4.7 mm) thick. 2. Maximum-Security Surface Hinges: inch (6.3 mm) thick. 3. Strike Reinforcements: inch (4.7 mm) thick. 4. Slide-Device Hanger Attachments: As recommended by device manufacturer. 5. Lock Fronts, Concealed Holders, and Surface-Mounted Closers: inch (2.3 mm) thick. 6. All Other Surface-Mounted Hardware: inch (2.3 mm) thick. 7. Lock Pockets: inch (3.1 mm) thick at non-inmate side, welded to face sheet. F. Hardware Enclosures: Provide enclosures and junction boxes for electrically operated detention door hardware of same material as detention door face sheets, interconnected with ULapproved, 1/2-inch- (12.7-mm-) diameter conduit and connectors. 1. Access Plates: Where indicated for wiring installation, provide access plates to junction boxes, fabricated from same material and thickness as face sheet and fastened with at least four security fasteners spaced not more than 6 inches (152 mm) o.c. G. Exterior Detention Doors: Construct exterior doors to comply with NAAMM-HMMA 863 and as specified. 1. Security Grade 3: Provide doors with face sheets of inch- (1.7-mm-) minimumthickness, metallic-coated, cold-rolled steel. 2.4 DETENTION FRAMES A. General: Provide fully welded detention frames with integral stops, of seamless construction without visible joints or seams. Fabricate detention frames continuously welded full depth and width of detention frame. B. Stop Height: Provide minimum stop height of inch (16 mm) for detention door openings and minimum stop height of 1-1/4 inches (32 mm) in security glazing or detention panel openings. C. Exterior Detention Frames: Construct exterior frames to comply with NAAMM-HMMA 863 and as specified. 1. Security Grade 3: Provide frames fabricated from inch- (1.7-mm-) minimumthickness, metallic-coated, cold-rolled steel. D. Hardware Reinforcement: Fabricate reinforcing plates from same material as detention frame to comply with the following minimum thicknesses: 1. Hinges and Pivots: inch (4.7 mm) thick by 1-1/2 inches (38 mm) wide by 10 inches (254 mm) long. 2. Strikes and Closers: inch ( 4. 7 mm) thick. 3. Surface-Mounted Hardware: inch (2.3 1mn) thick. 4. Lock Pockets: inch (3.1 mm) thick at non-inmate side, welded to face sheet. Provide inch- (3.1-mm-) thick, lock protection plate for attachment to lock pocket with security fasteners. DETENTION DOORS AND FRAMES

4 E. Jamb Anchors: Weld jamb anchors to detention frames near hinges and directly opposite on strike jamb or as required to secure detention frames to adjacent construction. 1. Number of Anchors: Provide two anchors per jamb plus the following: a. Detention Door Frames: One additional anchor for each 18 inches (457 mm), or fraction thereof, above 54 inches (1372 mm) in height. b. Detention Frames with Security Glazing or Detention Panels: One additional anchor for each 18 inches (457 mm), or fraction thereof, above 36 inches (914 mm) in height. F. Floor Anchors: Provide floor anchors for each jamb and mullion that extends to floor, formed of same material and thickness as detention frame. G. Rubber Door Silencers: Except on weather-stripped detention doors, drill stops in strike jambs to receive three silencers on single-detention-door frames and drill head jamb stop to receive two silencers on double-detention-door frames. Keep holes clear during construction. H. Grout Guards: Provide factory-installed grout guards of same material as detention frame, welded to detention frame at back of hardware cutouts, silencers, and glazing-stop screw preparations to close off interior of openings and prevent mortar or other materials from obstructing hardware operation or installation. 2.5 A. B. c. D. E. F. G. H. I. J. K. L. MATERIALS Hot-Rolled Steel Sheet: ASTM A 1011/A 1011M, CS (Commercial Steel), Type B. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, CS (Commercial Steel), Type B. Metallic-Coated Steel Sheet: ASTM A 653/A 653M, CS (Commercial Steel), Type B; with G60 (Z180) zinc (galvanized) or A60 (ZF180) zinc-iron-alloy (galvannealed) coating designation. Steel Plates, Shapes, and Bars: ASTM A 36/A 36M. Concealed Bolts: ASTM A 307, Grade A. Masonry Anchors: Same steel sheet as door face. Embedded Anchors: Hot-dip galvanized according to ASTM A 153/A 153M. Post-Installed Anchors: Torque-controlled expansion anchors. Welding Rods and Bare Electrodes: According to AWS specifications for metal alloy welded. Grout: Comply with ASTM C 476, with a slump of not more than 4 inches (102 mm) as measured according to ASTM C 143/C 143M. Insulation: Slag-wool-fiber/rock-wool-fiber or glass-fiber blanket insulation. Bituminous Coating: Cold-applied asphalt mastic, compounded for 15-mil (0.4-mm) dry film thickness per coat. DETENTION DOORS AND FRAMES

5 2.6 FABRICATION A. Fabricate detention doors and frames rigid, neat in appearance, and free of defects, warp, or buckle. B. Tolerances: ComplywithNAAMM-HMMA 863. C. Exterior Detention Doors: Provide weep-hole openings in bottoms of detention doors to permit entrapped moisture to escape. Seal joints in top edges of detention doors against water penetration. D. Hardware Preparation: Factory prepare detention doors and frames to receive mortised hardware, including cutouts, reinforcement, mortising, drilling, and tapping, according to final Door Hardware Schedule and templates provided by detention door hardware supplier. E. Factory cut openings in detention doors. F. Weld components to comply with referenced A WS standard. Weld before finishing components to greatest extent possible. Remove weld spatter and welding oxides from exposed surfaces by descaling or grinding FINISHES A. Factory Priming for Field-Painted Finish: Apply shop primer immediately after surface preparation and pretreatment. Apply a smooth coat of even consistency to provide a uniform dry film thickness of not less than 0.7 mil (0.02 mm). 1. Shop Primer: Manufacturer's or fabricator's standard, fast-curing, corrosion-inhibiting, lead- and chromate-free, universal primer complying with SDI A SECURITY FASTENERS A. Operable only by tools produced by fastener manufacturer or other licensed fabricator for use on specific fastener type. 1. Drive-System Type: Pinned Torx. 2.9 SEALANTS A. Security Sealants: Manufacturer's standard, nonsag, tamper-resistant polyurethane sealant ACCESSORIES A. Concealed Bolts: ASTM A 307, Grade A unless otherwise indicated. B. Embedded Plate Anchors: Mild steel shapes and plates, minimum 3/16 inch ( 4.8 mm) thick; with minimum 1/2-inch- (12.7-mm-) diameter, headed studs welded to back of plate. DETENTION DOORS AND FRAMES

6 C. Welding Rods and Bare Electrodes: According to A WS specifications. PART 3 -EXECUTION 3.1 EXAMINATION A. Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. B. Examine roughing-in for embedded and built-in anchors to verify actual locations of detention frame connections before detention frame installation. 3.2 PREPARATION A. Before installation and with shipping spreaders removed, adjust detention frames for squareness, alignment, twist, and plumbness to the following tolerances: 1. Squareness: Plus or minus 1116 inch (1.6 mm), measured at door rabbet on a line 90 degrees from jamb and perpendicular to frame head. 2. Alignment: Plus or minus 1/16 inch (1.6 mm), measured at jambs on a horizontal line parallel to plane of face. 3. Twist: Plus or minus 1/16 inch (1.6 mm), measured at opposite face corners of jambs on parallel lines, and perpendicular to plane of door rabbet. 4. Plumbness: Plus or minus 1/16 inch (1.6 mm), measured at jambs on a perpendicular line from head to floor. 3.3 INSTALLATION A. Anchorage: Set detention frame anchorage devices according to details on Shop Drawings and according to anchorage device manufacturer's written instructions. B. Where detention frames are fabricated in sections due to shipping limitations, assemble frames and install angle splices at each corner, of same material and thickness as detention frame, and extend at least 4 inches (102 mm) on both sides ofjoint. 1. Field splice only at approved locations. Weld, grind, and finish as required to conceal evidence of splicing on exposed faces. 2. Continuously weld and finish smooth joints between faces of abutted, multiple-opening, detention frame members. C. Apply bituminous coating to backs of frames before filling with grout. D. Placing Detention Frames: Install detention frames of sizes and profiles indicated. Set detention frames accurately in position; plumbed, aligned, and braced securely until permanent anchors are set. After wall construction is complete, remove temporary braces and spreaders, leaving surfaces smooth and undamaged. DETENTION DOORS AND FRAMES

7 E. Grout: Fully grout detention frame jambs and heads. Completely fill space between frames and adjacent substrates. Hand trowel grout and take other precautions, including bracing detention frames, to ensure that frames are not deformed or damaged by grout forces. F. G. H. I. J. K. Security Sealant: Apply polyurethane security sealant at all exposed gaps between detention frames and adjacent substrates. Swinging Detention Doors: Fit non-fire-rated detention doors accurately in their frames, with the clearances according to NAAMM-HMMA 863. Sliding Detention Doors: Fit sliding detention doors in their frames according to manufacturer's written instructions and as required to allow doors to slide without binding. Fire-Rated Detention Doors: Install with clearances as specified in NFPA 80. Smoke-Control Detention Doors: Install according to NFPA 105. Installation Tolerances: Comply with NAAMM-HMMA A. FIELD QUALITY CONTROL Inspect installed products to verify compliance with requirements. Prepare inspection reports and indicate compliance with and deviations from the Contract Documents. 3.5 ADJUSTING AND CLEANING A. Final Adjustments: Check and readjust operating hardware items immediately before final inspection. Leave work in complete and proper operating condition. Remove and replace defective work, including detention doors and frames that are warped, bowed, or otherwise unacceptable. END OF SECTION DETENTION DOORS AND FRAMES

8 THIS PAGE INTENTIONALLY LEFT BLANK

9 SECTION WOOD WINDOWS PART 1- GENERAL 1.1 SUMMARY A. Section includes aluminum-clad wood windows. 1.2 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: Include plans, elevations, sections, hardware, accessories, insect screens, operational clearances, and details of installation, including anchor, flashing, and sealant installation. C. Samples: For each exposed product and for each color specified. 1.3 INFORMATIONAL SUBMITTALS A. Product test reports. B. Sample warranties. 1.4 WARRANTY A. Manufacturer's Warranty: Manufacturer agrees to repair or replace wood windows that fail in materials or workmanship within specified warranty period. 1. Warranty Period: a. Window: 10 years from date of Substantial Completion. b. Glazing Units: 10 years from date of Substantial Completion. c. Aluminum-Cladding Finish: 10 years from date of Substantial Completion. PART 2 -PRODUCTS 2.1 WINDOW PERFORMANCE REQUIREMENTS A. Product Standard: Comply with AAMAIWDMA/CSA 101/I.S.2/A440 for definitions and minimum standards of performance, materials, components, accessories, and fabrication unless more stringent requirements are indicated. 1. Window Certification: WDMA certified with label attached to each window. WOOD WINDOWS

10 B. Performance Class and Grade: AAMA!WDMA/CSA 101/I.S.2/A440 as follows: 1. Minimum Performance Class: CW. 2. Minimum Performance Grade: 35. C. Thermal Transmittance: NFRC 100 maximum whole-window U-factor of 0.35 Btu/sq. ft. x h x deg F (2.0 W/sq. m x K). D. Solar Heat-Gain Coefficient (SHGC): NFRC 200 maximum whole-window SHGC of WOOD WINDOWS A. Aluminum-Clad Wood Windows: 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. Jeld-Wen, Inc. b. Marvin Windows and Doors. c. Pella Corporation. B. Operating Types: As indicated on Drawings. C. Frames and Sashes: Fine-grained wood lumber complying with AAMA/WDMA/CSA 101/I.S.2/A440; kiln dried to a moisture content of not more than 12 percent at time of fabrication; free of visible finger joints, blue stain, knots, pitch pockets, and surface checks larger than 1/32 inch (0.8 mm) deep by 2 inches (51 mm) wide; water-repellent preservative treated. 1. Exterior Finish: Aluminum-clad wood. a. Aluminum Finish: Manufacturer's standard fluoropolymer two-coat system with fluoropolymer color topcoat containing not less than 70 percent PVDF resin by weight and complying with AAMA b. Color: As selected by Architect from manufacturer's full range. 2. Interior Finish: Manufacturer's standard color-coated finish. a. Exposed Unfinished Wood Surfaces: Manufacturer's standard species. b. Color: As selected by Architect from manufacturer's full range. D. Insulating-Glass Units: ASTM E Glass: ASTM C 1036, Type 1, Class 1, q3. a. Tint: Clear. b. Kind: Fully tempered where indicated on Drawings. 2. Lites: Two. 3. Filling: Fill space between glass lites with air. 4. Low-E Coating: Pyrolytic on second surface. WOOD WINDOWS

11 E. Glazing System: Manufacturer's standard factory-glazing system that produces weathertight seal. F. Hardware, General: Provide manufacturer's standard corrosion-resistant hardware sized to accommodate sash weight and dimensions. 1. Exposed Hardware Color and Finish: As selected by Architect from manufacturer's full range. G. Hung Window Hardware: 1. Counterbalancing Mechanism: AAMA Locks and Latches: Operated from the inside only. 3. Tilt Hardware: Releasing tilt latch allows sash to pivot about horizontal axis. H. Weather Stripping: Provide full-perimeter weather stripping for each operable sash unless otherwise indicated. I. Fasteners: Noncorrosive and compatible with window members, trim, hardware, anchors, and other components. 1. Exposed Fasteners: Do not use exposed fasteners to greatest extent possible. For application of hardware, use fasteners that match finish hardware being fastened. 2.3 ACCESSORIES 2.4 INSECT SCREENS A. General: Fabricate insect screens to integrate with window frame. Provide screen for. each operable exterior sash. Screen wickets are not permitted. 1. Type and Location: Half, outside sashes. B. Aluminum Frames: Complying with SMA 1004 or SMA Finish for Exterior Screens: Matching color and finish of cladding. C. Glass-Fiber Mesh Fabric: 18-by-14 (1.1-by-1.4-mm) or 18-by-16 (1.0-by-1.1-mm) mesh of PVC-coated, glass-fiber threads; woven and fused to form a fabric mesh resistant to corrosion, shrinkage, stretch, impact damage, and weather deterioration. Comply with ASTM D 3656/D 3656M. 1. Mesh Color: Manufacturer's standard. 2.5 FABRICATION A. Fabricate wood windows in sizes indicated. Include a complete system for installing and anchoring windows. B. Glaze wood windows in the factory. WOOD WINDOWS

12 C. Weather strip each operable sash to provide weathertight installation. D. Complete fabrication, assembly, finishing, hardware application, and other work in the factory to greatest extent possible. Disassemble components only as necessary for shipment and installation. Allow for scribing, trimming, and fitting at Project site. PART 3 EXECUTION 3.1 INSTALLATION A. B. c. D. E. Comply with manufacturer's written instructions for installing windows, hardware, accessories, and other components. For installation procedures and requirements not addressed in manufacturer's written instructions, comply with installation requirements in ASTM E Install windows level, plumb, square, true to line, without distortion, anchored securely in place to structural support, and in proper relation to wall flashing and other adjacent construction to produce weathertight construction. Adjust operating sashes and hardware for a tight fit at contact points and weather stripping for smooth operation and weathertight closure. Clean exposed surfaces immediately after installing windows. Remove excess sealants, glazing materials, dirt, and other substances. Remove and replace sashes if glass has been broken, chipped, cracked, abraded, or damaged during construction period. END OF SECTION WOOD WINDOWS

13 SECTION DOOR HARDWARE PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Mechanical door hardware. 1.2 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: For electrified door hardware. 1. Include diagrams for power, signal, and control wiring. 2. Include details of interface of electrified door hardware and building safety and security systems. C. Door hardware schedule. 1.3 INFORMATIONAL SUBMITTALS A. Sample warranty. 1.4 CLOSEOUT SUBMITTALS A. Maintenance data. 1.5 WARRANTY A. Special Warranty: Manufacturer agrees to repair or replace components of door hardware that fail in materials or workmanship within specified warranty period. 1. Warranty Period: Three years from date of Substantial Completion unless otherwise indicated below: DOOR HARDWARE

14 PART 2 PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Means of Egress Doors: Latches do not require more than 15 lbf (67 N) to release the latch. Locks do not require use of a key, tool, or special knowledge for operation. B. Accessibility Requirements: For door hardware on doors in an accessible route, comply with the DOJ's "2010 ADA Standards for Accessible Design". 2.2 SCHEDULED DOOR HARDWARE A. Provide products for each door that comply with requirements indicated in Part 2 and door hardware schedule. 1. Door hardware is scheduled in Part DOOR GASKETING A. Door Gasketing: BHMA A156.22; with resilient or flexible seal strips that are easily replaceable and readily available from stocks maintained by manufacturer. 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. National Guard Products, Inc. b. Pemko Manufacturing Co. c. Zero International, Inc. B. Maximum Air Leakage: When tested according to ASTM E 283 with tested pressure differential of0.3-inch wg (75 Pa), as follows: 1. Smoke-Rated Gasketing: 0.3 cfm/sq. ft. (3 cu. m per minute/sq. m) of door opening. 2. Gasketing on Single Doors: 0.3 cfm/sq. ft. (3 cu. m per minute/sq. m) of door opening. 3. Gasketing on Double Doors: 0.50 cfm per foot ( cu. m/s perm) of door opening. 2.4 THRESHOLDS A. Thresholds: BHMA A156.21; fabricated to full width of opening indicated. 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. National Guard Products, Inc. b. Pemko Manufacturing Co. c. Zero International, Inc. DOOR HARDWARE

15 2.5 FINISHES A. Provide finishes complying with BHMA A as indicated in door hardware schedule. PART 3 EXECUTION 3.1 INSTALLATION A. Mounting Heights: Mount door hardware units at heights to comply with the following unless otherwise indicated or required to comply with governing regulations. 1. Standard Steel Doors and Frames: ANSVSDI A Custom Steel Doors and Frames: HMMA Wood Doors: DHI's "Recommended Locations for Architectural Hardware for Wood Flush Doors." B. Install each door hardware item to comply with manufacturer's written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work. Do not install surface-mounted items until finishes have been completed on substrates involved. '',' I c. Thresholds: Set thresholds for exterior doors and other doors indicated in full bed of sealant complying with requirements specified in Section "Joint Sealants." D. Perimeter Gasketing: Apply to head and jamb, forming seal between door and frame. 1. Do not notch perimeter gasketing to install other surface-applied hardware. E. Door Bottoms: Apply to bottom of door, forming seal with threshold when door is closed. 3.2 ADJUSTING A. Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for fmal operation of heating and ventilating equipment and to comply with referenced accessibility requirements. DOOR HARDWARE

16 3.3 DOOR HARDWARE SCHEDULE Door Hardware Set No. 1 Single Door No. B06; to have the following: Q!y. Item Manuf. Model Finish 1 Threshold NGP 950V MIL PEM 2001AV MIL ZER 566A MIL 1 Gasketing NGP l37sa MIL PEM 2891AS MIL ZER 328A MIL 1 Rain Guard NGP 16A CLR PEM 346C CLR ZER 142 MIL 1 Sweep NGP 202NA CLR PEM 368CN CLR ZER 539AA CLR Refer to Section for detention door hardware END OF SECTION DOOR HARDWARE

17 SECTION DETENTION DOOR HARDWARE PART 1- GENERAL 1.1 SUMMARY A. Section includes detention door hardware. 1.2 COORDINATION A. Templates: Obtain and distribute, to the parties involved, templates for detention doors, frames, and other work specified to be factory prepared for installing detention door hardware. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: For each type of detention door hardware. fuclude plans, elevations, sections, and attachment details. C. Detention Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware as well as installation procedures and wiring diagrams. Coordinate the Detention Door Hardware Schedule with detention doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of detention door hardware. 1.4 INFORMATIONAL SUBMITTALS A. Product test reports. B. Sample Warranties: For special warranties. 1.5 CLOSEOUT SUBMITTALS A. Operation and maintenance data. 1.6 MAINTENANCE MATERIAL SUBMITTALS A. Maintenance Tools and fustructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of detention door hardware. DETENTION DOOR HARDWARE

18 1.7 WARRANTY A. Special Warranty: Manufacturer agrees to repair or replace components of detention door hardware that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Structural failures including excessive deflection, cracking, or breakage. b. Faulty operation of operators and detention door hardware. c. Deterioration of metals, metal finishes, and other materials beyond normal weathering or detention use. 2. Warranty Period: Three years from date of Substantial Completion. 3. Warranty Period for Security Door Closers: 10 years from date of Substantial Completion. PART 2 PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Swinging Detention Door Assemblies: Provide detention door hardware as part of a detention door assembly that complies with security grade indicated, when tested according to ASTM F 1450, based on testing manufacturer's standard units in assemblies similar to those indicated for this Project. 2.2 DETENTION DOOR HARDWARE, GENERAL A. Regulatory Requirements: 1. Comply with accessibility requirements, comply with the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines and ICCA INSTITUTIONAL HINGES A. Institutional Hinges: Heavy weight; fabricated from steel; with two concealed maintenance-free ball bearings; nonremovable hinge pins; welded hospital tips; full mortise; drilled to BHMA A156.7 template dimensions for countersunk security fasteners; BHMA A156.1, Grade Base Metal: Cast stainless steel unless otherwise required for fire rating. 2. Hinge Pin: Stainless steel. 3. Reverse Safety Stud: Metal stud extension on back of each leaf that engages hole in reinforcing plate. 4. Size: As required by door size. 5. Finish: BHMA 630. B. Manufacturers: Subject to compliance with requirements, provide products by one of the following: DETENTION DOOR HARDWARE

19 1. Hager Companies. 2. McKinney Products Company, an ASSA ABLOY Group company. 3. Southern Folger Detention Equipment Company. 2.4 MECHANICAL DETENTION LOCKS AND LATCHES A. Lock Mountings: 1. Hollow-Metal Detention Doors: Mount detention lock to back of inch (4.65-mm) nominal-thickness, galvanized-steel cover plate for installation in lock pocket fabricated into detention door. Attach cover plate to hollow-metal detention door with security fasteners. B. Mechanical Deadlocks, Paracentric Cylinder: 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. Airteq Systems. b. Brink, R. R. Locking Systems, Inc. c. Southern Folger Detention Equipment Company. 2. Function: Deadlocked in both locked and unlocked position; latchbolt retracted and extended by six-tumbler paracentric cylinder; keyed two sides. 3. Latchbolt: 2-inch-high by 3/4-inch- (51-mm-high by 19-mm-) thick steel, with two casehardened-steel insert pins; 3/4-inch (19-mm) throw; 1/2-inch (13-mm) bolt projection when retracted. 4. Security Grade: 1 according to ASTM F 1450 or ASTM F DETENTION LOCK TRIM A. Levers: Solid stainless steel. B. Escutcheons for Paracentric Locks: inch- (3.18-mm-) thick, 3-inch- (75-mm-) diameter stainless steel with BHMA 630 finish. Attach with security fasteners. 1. Style: Double wing. 2.6 DETENTION CYLINDERS AND KEYING A. Source Limitations: Subject to compliance with requirements, provide cylinders and keying for paracentric and mogul cylinders by same manufacturer as for detention locks and latches. B. Paracentric Cylinders: Manufacturer's standard lever-tumbler type, constructed from one-piece spring-tempered brass; with tumblers activated by phosphor bronze springs; five tumblers per lock. C. Keying System: Provide a factory-registered keying system complying with the following requirements: DETENTION DOOR HARDWARE

20 1. Paracentric cylinders operated by change keys only. D. Keys: Provide cast silicon-bronze copper alloy keys complying with the following: 1. Stamping: Permanently inscribe each key with a visual key-control number and include the following notation: a. Information to be furnished by Owner. 2. Quantity: In addition to one extra blank key for each lock, provide the following: a. Cylinder Change Keys: Three. 2.7 DETENTION OPERATING TRIM A. Standard: BHMA Al56.6, Grade 1. B. Surface-Mounted Door Pulls: 8-3/4-inch (222-mm) overall length and 2-1/4-inch (57-mm) projection; attach to door with two security fasteners. 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. Airteq Systems. b. Brink, R. R. Locking Systems, Inc. c. Southern Folger Detention Equipment Company. 2. Material: Cast stainless steel with BHMA 630 finish. 2.8 SECURITY DOOR CLOSERS A. Standard: BHMAA156.4, Grade Certified Products: Provide security door closers listed in BHMA's "Directory of Certified Door Products." B. Surface-Mounted Security Door Closers: 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: a. Corbin Russwin, Inc.: an ASSA ABLOY Group company. b. LCN; an Allegion brand. c. Norton Door Controls; an ASSA ABLOY Group company. 2. Arms: Minimum 3/8-inch- (9.5-mm-) thick by inch- (29-mm-) wide, rectangular steel main arm; 5/16-inch- (8-mm-) thick by l-inch- (25-mm-) wide, rectangular steel secondary arm; full rack-and-pinion type; fabricated with orbital-riveted, pinned, or welded elbow and arm shoe/soffit plate joints designed to prevent disassembly with ordinary hand tools. 3. Cover: Heavy-duty metal, attached with four security fasteners. DETENTION DOOR HARDWARE

21 4. Mounting: Attach security door closer with security fasteners. C. Unit Size: Comply with manufacturer's written recommendations for size of security door closers depending on size of door, exposure to weather, and anticipated frequency of use. Provide factory-sized closers, adjustable to comply with field conditions and requirements for opening force. 2.9 FABRICATION A. Base Metals: Produce detention door hardware units of base metal, fabricated by forming method indicated, using manufacturer's standard metal alloy, composition, temper, and hardness. Furnish metals of a quality equal to or greater than that of specified detention door hardware units and BHMA Al56.18 finishes. B. Fasteners: Provide flat-head security fasteners with finished heads to match surface of detention door hardware. 1. Security Fasteners: Fabricate detention door hardware using security fasteners with head style appropriate for fabrication requirements, strength, and finish of adjacent materials. Provide stainless-steel security fasteners in stainless-steel materials. 2. Concealed Fasteners: For detention door hardware units that are exposed when detention door is closed, except for units already specified with concealed fasteners. Do not use through bolts for installation where bolt head or nut on opposite face is exposed unless it is the only means of securely attaching detention door hardware. Where using through bolts on hollow-metal detention door and frame construction, provide sleeves for each through bolt HARDWARE FINISHES A. Standard: Comply with BHMA A SECURITY FASTENERS A. Operable only by tools produced by fastener manufacturer or other licensed fabricator for use on specific fastener type. PART 3 -EXECUTION 3.1 EXAMINATION A. Examine detention doors and frames, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance of the Work. B. Examine roughing-in for embedded and built-in anchors to verify actual locations of detention door hardware connections before detention door hardware installation. DETENTION DOOR HARDWARE

22 c. D. Inspect built-in and cast-in anchor installations, before installing detention door hardware, to verify that anchor installations comply with requirements. Prepare inspection reports. Examine roughing-in for electrical power systems to verify actual locations of connections before detention door hardware installation. 3.2 A. PREPARATION Steel Detention Doors and Frames: Comply with BHMA Al Series. 1. Surface-Applied Detention Door Hardware: Drill and tap detention doors and frames according to SDI A INSTALLATION A. B. Mounting Heights: DHI's "Recommended Locations for Builders' Hardware for Custom Steel Doors and Frames." Where cutting and fitting are required to install detention door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work. Do not install surfacemounted items until finishes have been completed on substrates involved. 1. Set units level, plumb, and true to line and location. Adjust and reinforce attachment substrates as necessary for proper installation and operation. 2. Drill and countersink units that are not factory prepared for anchorage fasteners. Space fasteners and anchors according to industry standards. c. D. Install interconnecting wiring and connectors between detention door hardware devices. Terminate device wiring for detention door hardware installed in swinging doors at a plug-type connector located in lock pocket or door frame junction box. Security Fasteners: Install detention door hardware using security fasteners with head style appropriate for installation requirements, strength, and finish of adjacent materials. 3.4 DETENTION DOOR HARDWARE SCHEDULE A. General: Provide detention door hardware for each detention door to comply with requirements in this Section and with detention door hardware sets. DETENTION DOOR HARDWARE

23 Door Hardware Set No. 1 Single Door No. B06; to have the following:!$ Item Manuf. Model Finish 11/2 pr. Institutional Hinges HAG IHTAB McK HTB SF 204FMSS Security Closer CR DC821 OxA12xM LCN CNS-72MC 689 NOR UNI9500M Deadlock AS 5066-K2 Galv BLS 7076 Galv SF 1070A-2 Galv 1 Institutional Pull AS 612 US32D BLS US26D SF 212C US32D Provide deadlock manufacturer's trim, strike and other items necessary for a complete, fullyfunctional door. Refer to Section for remainder of door hardware END OF SECTION DETENTION DOOR HARDWARE

24 THIS PAGE INTENTIONALLY LEFT BLANK