DOWNLOADABLE PROJECT PLANS FROM THE EDITORS OF WOOD MAGAZINE DRILL-PRESS TABLE page 1 of 6

Transcription

1 OWNLOL PROJT PLNS FROM TH ITORS OF WOO MGZIN RILL-PRSS TL page 1 of 6

2 Start with the horizontal table pieces 1 ut the horizontal table () to the size listed in the ill of Materials. (ue to its stability and strength, we used altic birch plywood as sourced in the uying Guide.) 2 ut the horizontal tabletops (, ) to size. (fter using the drill-press table awhile, the center piece will get several holes drilled into it. For ease in replacing the tabletop center, we constructed the tabletop out of three pieces rather than one.) 3 Using a hacksaw, crosscut three pieces of metal mini channel to the lengths listed on the xploded View drawing. (We used -Line Systems 72 mini channel. See the uying Guide for our source.) rill countersunk mounting holes at 4" intervals through the mini channel for screwing to the plywood tables later. 4 Mark the location of the groove on the bottom surface of the horizontal table (). Position the table on the top of your metal drill-press table. Looking through the slots on your drill-press table, verify that the marked groove crosses at least two of the grooves in your metal table. If not, adjust the position of the groove. 5 Using a dado blade in your tablesaw, cut a Å" dado and rabbets (wide enough to house the mini channel just cut) in parts and, where dimensioned on the xploded View and Front View drawings. 6 Position and clamp the tabletops (, ) onto the horizontal table () where shown on the xploded View drawing. rill countersunk holes through the bottom side of to secure and in place. Remove the clamps, and glue and screw both s in place. Then, just screw (no glue) part in place. 7 ut a 2fi" radius centered on the back edge of /. 8 Screw the three pieces of mini channel in place. uild the fence for precision alignment 1 ut the horizontal fence pieces (, ) to size. Mark a 2fi" radius on each where shown on the Horizontal Fence drawing, and bandsaw and drumsand the radii to shape. The radius centered on allows the drill-press chuck to come closer to the workpiece, which is especially helpful when using a small bit in the chuck. The radius in the fence base () allows the fence to be moved closer to the drill-press column when drilling into wide stock. 2 Mark a pair of hole centerpoints on the fence base (). efore drilling the holes, verify that the marked points are centered over the dadoes opening in the tabletop. Improperly located, the carriage bolts will bind in the mini channel. djust if necessary, and drill the " holes. 3 rill the countersunk mounting holes, and screw part to, checking for square. 4 To mount the fence to the table, start by grinding two opposing edges of four " carriage bolts until the bolt heads slide easily in the metal mini channel. See the arriage olt details accompanying the Front View drawing for reference. Then, insert the bolts through the fence piece through flat washers and into the plastic wing nuts (knobs). The fence should slide back and forth in the table easily, but without slop. The hold-downs come next 1 ut the clamp hold-down base (F) to size from fl" stock. (We resawed some of the plywood we used for the other pieces.) For holding -thick stock later, the base must be less than thick. ut or sand a " radius on each corner of F. 2 rill a fi" hole ˇ" deep in the top of the hold-down base. Now, drill a ˇ" hole, centered through the middle of the counterbore. 3 Insert a ˇ" carriage bolt into the bottom surface of the hold-down base. (For ease in using the hold-down clamp, we found that the hold-down base must swivel on the tops of the tables. To do this, we had to use a ˇ" carriage bolt instead of the " bolts used on the fences.) 4 Grind the threaded end of the four #12Xfl" panhead sheet-metal screws until the threaded end is fi" long. Then, drill pilot holes, and secure the hold-down clamp to F with the four screws. Part horizontal table tabletop sides tabletop center horizontal fence base horizontal table fence F hold-down base ill of Materials Finished Size* T W L TL SSMLY 7 15" P 1 fl" 15" 24 P 1 8fi" 3" 2 " 15" FN N HOL-OWN 3 " Matl. Qty. P 2 24 P 1 2" 24 P 1 P 1 Material Key: P altic birch plywood Supplies: #6Xfl", #8X1 ", #8X1fi" flathead wood screws; 4 X1fi" and 1 ˇX1" carriage bolts; 1-ˇ" locknut; 4 ˇ" flat washers; 2 ˇ" plastic wing nut; 2 3Œ" oval-tapered knob; 2 2"- reach hold-down clamp; 1 XÅX24 mini channel (available at most electrical supply outlets); 2 XÅX15" mini channel; 4 #12Xfl" panhead sheet-metal screws; clear finish. uying Guide Hardware kit. Three pieces of XÅ" mini channel cut to length; one 2"-reach hold-down (toggle) clamp; two plastic wing nuts (knobs), two 3Œ"-long oval-tapered knobs, four " carriage bolts 1fi" long, and one ˇ" carriage bolt 1" long, plus the screws, washers, and locknuts listed above. WOO KIT SPT1, $42.95 plus $3.75 shipping. Schlabaugh and Sons Woodworking, th Street, Kalona, I or call 800/ to order. (ontact via schsons@kctc.net) asy-to-assemble kit. ll the pieces listed in the hardware kit above, plus all the altic birch plywood pieces listed in the ill of Materials cut to size and shape with predrilled holes. WOO KIT SPT2, $99.95 plus shipping (call for shipping charges). Schlabaugh and Sons Woodworking, address and phone number above. page 2 of 6

3 Here s how to secure the assembly to your drill press 1 Sand all the parts. Mask off the metal mini channel and apply a clear finish to the wood parts (we used an aerosol lacquer). 2 Secure the wooden drill-press table to the metal table with a pair of " carriage bolts (with the edges of the head ground as previously explained and shown on the arriage olt details), flat washers, and tapered knobs. (We found the long tapered knobs easy to grab and the table easier to relocate when needed.) Slide the fence with knobs attached onto their mating mini channel. The slot configuration on drillpress tables varies from model to model. If your drill press has a round table with radial slots (X shaped), you ll need to put the positioning bolts and mating tapered knobs in the back two slots in your metal table. To achieve infinite positioning of the wooden table you can do three things: (1) rotate the metal table in the drill-press support arm, (2) rotate the support arm, (3) rotate the drill-press head. aution: efore rotating the drill-press head, make sure the drill press is securely bolted down. Rotating the head changes the weight distribution, and can cause the drill press to tip over. Produced by Marlen Kemmet Project esign: Meredith orporation ll Rights Reserved Illustrations: Lorna Johnson; Roxanne LeMoine Photographs: John Hetherington Graphic esign: Lorna Johnson OPYRIGHT MRITH ORPORTION 1998 The purchase of these plans does not transfer any copyright or other ownership interest in the plans, the design, or the finished project to the buyer. uyer may neither reproduce the plans for sale nor offer for sale any copies of the finished project. UTTING IGRM *Plane or resaw to thickness listed in the ill of Materials. * F 3/4 x 48 x 48" irch plywood page 3 of 6

4 1 /2" counterbore 5/16" deep with a 5 /16" hole centered inside 3 /4" from end Plastic wing nut 5/16" carriage bolt 1" long 3 /8 x 13 /16 x 15" mini channels F 5/16" locknut 9/64" pilot hole 1 /4" radius 5/16" washer #12 x 5 /8" P.H. sheet-metal screw (Grind threaded end to 1 /2" long.) 3/8" carriage bolt 1 1 /2" long 15" 3/4" #6 x 5 /8" F.H. wood screw, countersunk in 1 3 mini channel /4" 13 /16" rabbets 7/16" deep 4 1 /2" 3/8 x 13 /16 x 24 3 /4" mini channel #8 x 1 1 /4" F.H. wood screw 3/8" carriage bolt 1 1 /2" long 5/16" washer 13/16" dado 7/16" deep Relocate groove, if necessary, to cross two of the grooves in your drill-press table. 3 7 /8" oval-tapered knob XPLO VIW page 4 of 6

5 RRIG OLT TILS 5/8" 2"-reach hold-down (toggle) clamp Grind edges of all 3 /8" carriagebolt heads to fit mini channel. Ground edges 1 1 /4" 1 /4" 3/4" F o not grind edges of hold-down carriage bolt. 2" FRONT VIW Metal drill-press table 7 3 /4" 8 1 /2" 2" 3" 8 3 /32" 3/4" HORIZONTL FN 3 /8" hole 12 3 /8" 3 /4" #8 x 1 1 /2" F.H. wood screw 24 3 /4" 5 /32" shank hole, countersunk 10 1 /4" 1 1 /8" 8 3 /32" 7 /64" pilot hole 3 /4" deep page 5 of 6

6 rilling numerous holes all in a straight line is easy using the horizontal table and fence. For instance, if you need holes exactly 2" from the edge of a piece of stock, position the inside edge of the fence exactly 2" from the center of the bit. Now, just move the stock along the fence and all the holes will be drilled exactly 2" from the edge of the stock as shown in Photo. Making round-cornered mortises and the mating tenons is easy to accomplish using our fence system. s shown in Photo, drill a hole with a Forstner bit to form the mortise. You can use this same setup for drilling holes in the edge of a piece of stock as shown in Photo. This setup is especially useful for drilling dowel holes in the edge of stiles. page 6 of 6