FS-PORTAL LM Folding - sliding door hardware for aluminium elements with Eurogroove

Size: px

Start display at page:

Download "FS-PORTAL LM Folding - sliding door hardware for aluminium elements with Eurogroove"

Phillip Maxwell
5 years ago
Views:

1 FS-PORTL LM Folding - sliding door hardware for aluminium elements with Eurogroove... with these decisive advantages:: Top or bottom running with the same profile set Stable running rail with favourable threshold height Wide range of adjustment possibilities Free running due to 4-roller, ball bearing rollers Integral stop FSgb7004_3_03.03/0 printed on unchlorinated bleached paper Size range Sash width (mm) 330 ) to 900 Sash height (mm) 850 to 00 erived from the sash widths depending on the Frame outside width (mm) profile system and diagram Sash weight (kg) max. 80 Over rebate height (mm) 0 to 6 2) ) ccess sashes very possibly larger than 600 mm! 2) 7-9 mm over rebate heights with FS-PORTL LM packers on enquiry The size ranges stated above apply to the SIEGENI FS-PORTL LM hardware. In addition to this, the details given by the profile manufacturer or system owner apply, particularly on possible limitations to sash dimensions, max. number of sashes per element, sash weight and locking spacing. Where there are special manufacturing rules or working guidelines, these must be expressly observed. ssembly hint: at the end of the folding package at 90 to the installation, a wider frame and an LM removable handle should be fitted. ssembly Instructions FSgb FSgb7004

2 iagram-summary FS-PORTL LM iagram summary iagram 32 iagram 330 ) ccess through st folding sash 2) s = Point, opposite hand etc. F F2 F s 2) F F2 F E 2 Folding sash ccess sash 3 Folding sash 0 ccess sash ) iagram 43 F F2 F2 F F s 2) Note: ll diagrams can also be used opposite hand. 3 Folding sash ccess sash iagram 54 iagram 550 iagram 532 F F2 F3 F2 F s 2) F F2 F3 F2 F s 2) s 2) E s 2) s 2) F F2 F3 F2 F 4 Folding sash ccess sash 5 Folding sash 3+2 Folding sash 0 ccess sash ) 0 ccess sash ) iagram 65 iagram 633 F F2 F3 F2 F3 F F s 2) F F2 F3 F F3 F2 F s 2) s 2) s 2) 5 Folding sash ccess sash 3+3 Folding sash 0 ccess sash ) iagram 76 iagram 770 iagram 743 F F2 F3 F2 F3 F2 F s 2) F F2 F3 F2 F3 F2 F E F F2 F3 F2 F3 F2 F s 2) s 2) s 2) 6 Folding sash ccess sash 7 Folding sash 4+3 Folding sash 0 ccess sash ) 0 ccess sash )

4 Illustration of hardware (I) FS-PORTL LM Illustration of hardware (I) Illustration of hardware (II) FS-PORTL LM Illustration of hardware (II) In the FS profile set bottom running s E top running F s In the FS sash hinge In the FS roller In the FS roller E F carton carton 3 2 carton S = G - 28 S2 = G S = G - 28 S2 = G S = G - 28 S2 = G S = G - 28 S2 = G S = G - 28 S2 = G Sash outside edge

5 Hardware List (I) Hardware List (II) FS-PORTL LM Hardware List (I) FS- PORTL LM Hardware List (II) EN Items per diagram Item. escription silver dark bronze white FS-PORTL components -5 arton - Sash hinge FS-LM Intersection point arton - Rollers FS-LM Intersection point , 5-8 arton - Rollers FS-LM Intersection point Profile set FS Size R (mm) to to to to No illust. ag of countersunk screws 4.2 x 9 ontents: 25 off 2802 Requirement depends on profile set size ) asic requirement Version: = ccess sash with turn sash hardware; K = ccess sash with turn & tilt hardware K K K K K Handle - Si-line LM see LM handle summary rawing No. LMde S LM ottom hinge pin ottom hinge ountersunk screw M5 x 8, orner hinge lamping piece E Retainer Top hinge pin Top hinge ountersunk screw M5 x 7, Stay hinge Stay LM No illust No illust Stay LM 4200-K Size VS LM 4200-K or VS LM 4200-K VS LM-/FS Striker orner drive VSO oupling bracket heese head screw M5 x Locking bolt Striker S Requirement depends on FH No illust MV LM 4200-K VSU/SO from FH 250 mm MV LM VS/S from FH 250 mm Striker MV Locking bolt ) for Size 250 max. 30 Size 350 max. 39 Size 450 max. 48 Size 700 max. 72

6 FS-PORTL LM Packing Units reak own Item Quantity escription silver EN darkbronze white arton -Sash hinge FS-LM Intersection point comprising: 3 Sash hinge, wide over cap F, wide Sash hinge, narrow over cap F, narrow Top hinge pin No illust. 2 ountersunk screw M5 x 6 for item and No illust. 2 lind riveting nut for csk. screw M5 x arton -.Roller FS-LM comprising: Intersection point Sash hinge, wide over cap F, wide Sash hinge, narrow over cap F, narrow Top hinge pin ottom hinge, right hand over cap E, right hand ottom hinge, left hand over cap E, left hand Roller Guide No illust. 0 ountersunk screw M5 x 6 for item, 3, 6 and No illust. 4 ountersunk screw M5 x 3 for item No illust. 0 lind riveting nut for csk. screw M5 x ag - Supports comprising: Support Support F losure cap No illust. 4 ountersunk screw M5 x 2 for item 2 and No illust. 4 lind riveting nut for csk. screw M5 x arton -Roller FS-LM comprising: Intersection point Roller Guide ottom hinge, right hand over cap E, right hand ottom hinge, left hand over cap E, left hand No illust. 6 ountersunk screw M5 x 6 for item 5 and No illust. 6 lind riveting nut for csk. screw M5 x Profile set FS Guide rail over rail F Running rail Size Size Size Size over rail L Size over strip Size 70 Length (mm) Length (mm) Length (mm) R (mm) to to to to Length (mm) Length (mm)

7 Installation Instruc- FS-PORTL LM Installation Instructions (I) Installation Instructions Preparation For machining and installation of the sash, frame and operating rod profiles for the Hinge sides for intersection points Locking sides for intersection points, E and F see ssembly Instructions for LM 4200-K, LM and LM 4200-S. Fitting the sash frames Put together the folding sashes in appropriate pairs and drill the holes for sash hinges ( and 3), bottom hinge (6 and 8) and bottom hinges (5 and 7). For this see front page and FS-PORTL LM assembly aids. For elements with a loose folding sash (intersection point F) drill the holes for support (2) and support F (3). Screw on sash hinges ( and 3) plus bottom hinge (6 and 8) and bottom hinges (5 and 7). For sash hinge, wide () ensure vertical alignment. For elements with a loose folding sashes (intersection point F) screw on support (2) and support F (3). Lightly grease support (2) and support F (3). Fitting on the frame ut guide rail (9), two cover rails F (20) and running rail (2) to length (length = R). N..: ut off the running rail (2) on the opposite side to the access sash. Screw on guide rail (9) and running rail (2). Note: In the area of the folded element (approx. 500 mm) all the screws, after this only every 2nd screw, or for the running rail alternately top and bottom. Final fitting Push the roller (0) into the running rail. Fit the folding sashes in order, beginning with the frame side sash. To fit the roller(0) lay spacer strips (customer to provide) in the rebate groove as a fitting aid. Push roller (0) into the supporting plate on bottom hinge (8) and bottom hinge (7). For this bring the adjusting nut into the right position, see Picture. Hold the top hinge pin L of the roller (0) with 5 mm /F socket head wrench and tighten the clamping nut with 7 mm open ended spanner, see Picture 2. Push the guide() into the supporting plate of both bottom hinge (6) and bottom hinge (5) and tighten with 3 mm open ended spanner, see Picture 3. SW 5 SW 3 adjusting nut Picture ring the adjusting nut into the right position and push in the roller SW 7 Picture 2 Hold the top hinge pin L with 5 mm /F socket head wrench and tighten the clamping nut with 7 mm open ended spanner Picture 3 Push the guide into the supporting plate and tighten with 3 mm open ended spanner

8 FS-PORTL LM Installation Instructions (II) Final fitting (continued) lip lip on on all all cover cover caps. caps. ut ut cover cover rails rails F (20) F (20) to to length length and and clip clip on. on. ut ut cover cover rail rail L L (22) (22) to to length (Length = Roller Roller to to outer outer edge edge of of frame). lip lip cover cover rail rail L L (22) (22) onto onto running rail, rail, see see Picture To To protect against contamination during the the construction period, e.g. e.g. when when plastering in in the the element, fit fit cover cover strips strips (23) (23) between the the individual folding elements, see Picture 4. cover strip cover rail see Picture 4. Picture 4 4Inserting cover strip and cover rail raill L Fixing the hardware components Sash hinges ( and 3):... ountersunk screw M5 x 6 ) ottom hinge (6 and 8):... ountersunk screw M5 x 6 Support (2) and Support F (3):... ountersunk screw M5 x 2 ottom hinge (5 and 7):... ountersunk screw M5 x 6 Guide rail (9)... ountersunk self tapping screw 4.2 x 9 Running rail (2)... ountersunk self tapping screw 4.2 x 9 Fixing screws are included in the delivery specification. Note: For narrow profiles on which the blind riveting nuts cannot be used at intersection point (sash hinges, external), the fixing can alternatively be done using self cuttingscrews M5 x 3. For this modify the jigs E by fitting suitable 4.2 drilling bushes. Order Ref. No. for 4.2 drilling bush Order Ref. No.. for self cutting countersunk screw M5 x ) For Intersection point, top and bottom with M5 x 3 countersunk screw Wedging using 43 as an example Note: lways wedge to the load bearing side, see illustration on right ccess sash with turn & tilt hardware possible with diagrams Intersection point 32, 54 and 76 Intersection point F 43 and 65

9 Regulierungsmöglichkeiten FS-PORTL LM djustment possibilities djustment possibilities If necessary the adjustment possibilities listed below can be used. For proper adjustment the following is recommended: o not adjust until after the glass panes are fitted lamp the folding - sliding element firmly horizontally and vertically or only adjust after building into the brickwork height of sash over rebate 0-6 mm SW 3 Setting the sash contact pressure of the bottom hinge Release the /F 3 clamp screw on the bottom hinge. Push the sash firmly into contact Tighten the clamping screw. 2 ± 2,5 mm 2 Setting the width of the sash hinges - + SW 4 Note: Release sash hinges one after another, adjust and screw on again. Loosen both fixing screws slightly. djust the gap width with 4 mm hex. socket wrench. Retighten the fixing screws. 3 Setting the roller height SW ± 3,5 mm SW 5 3 SW 7 Loosen the 7 mm clamping nut on the roller slightly. Fit packing under the sash in the rebate to give the precise dimension and adjust the height with a 5 mm socket wrench, holding the clamping nut steady with a 7 mm open ended spanner. Retighten the 7 mm /F clamping nut, holding the pin with the 5 mm socket wrench. djustment possibilities for the LM components Side adjustment: through stay LM 4200 (35) Height adjustment: after removing the top pressure piece from the bottom hinge (26), through the 4-mm socket head screw in the corner hinge (28) +.5 / mm ontact pressure: through the eccentric locking cam see Maintenance Instructions LM.

10 ssembly ids FS-PORTL LM ssembly ids ca. 0,4 x F ca. 0,4 x F Standard fixing ca. 00 lternative fixing if standard not possible due to profile. Remove unwanted drilling bushes. - only jig E645-2 shown max. 4 mm ca. 00 = = N.. The jigs are matched to a sash distance of 4 mm. epending on the profile system, stick on a suitable distance piece, max. 4 mm thick. See Section - and front page intersection point. Ø 7, mm Ø 4,2 mm Intersection point External view Intersection point Internal view Intersection point Internal view Jig E 645- for bottom hinge EN Requirement: 2 off 43 rill: Ø 7. Ø 4.2 Jig E for sash hinge Requirement: 4 off 433 rill: Ø 7. Jig E for support Requirement: off rill: Ø 7. Jig E for drill location for guide and running rail Requirement: off rill: Ø 3.5 djusting rod for E 645- and E Requirement: 2 off 437 Stop for adjusting rod Requirement: 2 off 4300 lamping fixture for E 645- and E Requirement: 9 off lamping fixture 0089 for E (outside) Requirement: 3 off 3929 No illustration ountersunk screw M5 x 6 for fixing the clamping fixture Requirement: off 8047

11 Important Notes, bbreviations FS-PORTL LM Important Notes, bbreviations Important Notes - The size ranges specified on the front page must never be exceeded. - For the SIEGENI-UI FS-PORTL LM hardware, the size ranges specified on Page apply. In addition to this the details given by the profile manufacturer or the system owner, particularly on possible limitations to sash dimensions, maximum number of sashes per element, sash weight and the spacing of locking elements also apply. Where specific manufacturing regulations or working guidelines exist, these are to be expressly observed. - It is possible that bearing components can break due to excessive strain. This could cause the window to drop out of the frame and potentially cause serious injuries. If due to special circumstances (use in schools, nurseries etc.) excessive strain on bearing components can be expected, fatigue of these components must be prevented e.g. by fitting a lockable handle to prevent unauthorised use. In the event of doubt please consult your SIEGENI-UI representative. - The hardware components described in these ssembly Instructions are made of non-rusting material or have been galvanised and yellow chromatised to IN They must not be installed for use in aggressive, corrosion promoting air. In such cases please consult your SIEGENI-UI representative. - We can accept no liability in respect of any damages or defects arising where the hardware assembly incorporates products not made by SIEGENI-UI. - Install all the hardware components correctly as described in these ssembly Instructions. - The surface treatment of folding - sliding elements must be performed before the hardware is assembled on the window. Post treatment could adversely affect the effective functioning of the components, in which case we are not obliged to provide any warranty. - Please follow the standard techniques for packing and wedge the sealed glazing units within the sash/frame. - Keep all grooves and rebates free from dirt and debris - especially residues of cement or plaster. void the direct effect of moisture on the hardware and contact of the hardware with cleaning agents. - ffix a clearly visible operating sticker (sliding direction IN left or IN right) onto the fitted folding - sliding sash. The operating sticker can be found in the FS-LM Roller or FS-LM Roller carton. Liability exclusions We accept no liability in respect of any damages or malfunctions caused by the hardware or the folding - sliding elements fitted with them, as a result of incorrect or inappropriate specifications or other information provided by the customer, failure to follow these instructions, wilful damage or negligence or misuse or alteration or repair of or an exertion of excessive force to the hardware by the user or customer. bbreviations The following abbreviations are used in these ssembly Instructions: tl. ag F Folding sash R Frame outer width F Frame clearance dimension F Sash width RH Frame outer height Turn sash FH Sash height RF Frame rebate width E rill jig MV entre lock VSO Locking side top E/EL ottom hinge OKFF Upper surface of finished floor VSU Locking side bottom E ottom hinge - turn sash SIEGENI-UI KG - HRWRE N VENTILTION TEHNOLOGY P.O. OX Siegen - Tel Fax

FAVORIT Si-line - KF 3

FAVORIT Si-line - KF 3 Turn/tilt fitting for single sash PVCu windows with 2 mm air gap Botm tilt point - finish TS silver - handle height variable/centre 34 25 24 3 7 3 2 23 22 20 3 4 6 2 8 3 5 FKgb033_3_0.04/ printed on chlorine-free