COMPETENCY ANALYSIS PROFILE Tool and Die Maker 430A (All unshaded skill sets must be demonstrated/completed)
|
|
- Christina Patrick
- 5 years ago
- Views:
Transcription
1 COMPETENCY ANALYSIS PROFILE Tool and Die Maker 430A (All unshaded skill sets must be demonstrated/completed) SKILL SETS SKILLS PROTECT SELF AND OTHERS Identify health and safety hazards. Wear, adjust, and maintain personal protective equipment. Wear, adjust, and maintain respiratory protectors. Practice safe work habits. Follow fire procedures Operate emergency safety equipment Practice industrial hygiene housekeeping in the workplace Conduct preoperational check of equipment Report injuries Follow procedures for applying first aid Lock out mechanical equipment for repair Handle designated substances Operate lifting equipment PLAN AND PREPARE FOR MACHINING JOB Read and interpret engineering drawings. Perform calculations for machining operations. Read and interpret workprocess Verify workpiece material. cutting fluids machines check machine controls and systems select tooling prepare cutting tools measuring instruments and checking devices Select machine speeds and feeds Lay out features of engineering drawings select workholding devices Pick up datum/starting lifting and rigging equipment Communicate with co-workers
2 WORK-IN- PROCESS DIMENSIONAL OR SURFACE VERIFICATION Check straight cuts. Check shapes. Check threads. Check holes. Check tapers Check hardness Deburr Check surfaces BENCH WORK Hand-file. Hand-saw. Hand-drill holes. Hand-tap threaded holes. Hand-ream Chase threads Hand-grind
3 SAWING Check fused/welded blade. Lay out features of engineering drawings. workpiece in saw. feeds of saw. Install and test-run blade Check first cut-off Cut shapes using a vertical bandsaw Cut squared and angled surfaces using a power cut-off saw Deburr DRILLING USING DRILL PRESS/ MACHINE Select drill tooling. prepare cutting tools for drills. workpiece in drill. Set up tooling in drills. feeds of drill Center-drill a layout punch mark Drill a hole Chamfer a hole Ream a hole Machine-thread a hole Spot-face a hole Counter-bore a hole Counter-sink a hole Deburr
4 MACHINE GRINDING Select grinding wheel. Check condition of grinding wheel. Install grinding wheel. workpiece in grinder. Surface grind Hone holes Lap workpiece Grind inside and outside diameters. (ID/OD) Grind tools and cutters Check ground surfaces LATHE WORK Select lathe cutting tools. prepare lathe workpiece in lathe. Set up lathe feeds of lathe Take a sizing (preliminary) cut Establish a reference or starting point (datum) Face a surface Turn an external diameter Drill a hole Bore an internal diameter Ream a hole Tap a hole Turn an internal or external thread Produce a taper Knurl cylindrical surface patterns Groove and partoff Deburr housekeeping
5 MILLING Select milling prepare milling Set-up and maintain milling adjustable support tools. Set-up milling feeds of mill Perform fly-cutting. Face-mill Machine steps, cut-outs, angles, and open slots Machine a pocket or slot Machine a hole Bore holes Deburr NC/CNC COMPUTERIZED CONTROLLED MACHINING numerically controlled machining process and set up NC/CNC cutting tools and tool holders. and set machine parameters. Position, align, & secure workpiece in NC/CNC machine. Input and verify part program to NC/CNC machine controls Monitor NC/CNC machining process. Verify tool sequence, tool path, and collision avoidance program. Make adjustments to tooling and offsets
6 ELECTRICAL DISCHARGE MACHINING (edm) EDM process. Develop EDM electrodes. and set up EDM machining and set machine parameters. Position, align, and secure workpiece in EDM machine Cut the workpiece by EDM machine Practise good DEVISE AND DETAIL A PLAN FOR THE DIE OR TOOL-BUILDING PROCESS Verify the features of die or tool Develop and organize a die or tool-building plan. Perform die or tool-building related calculations. Assemble and verify die or tooling stock materials. Produce a detailed sketch of die or tooling FABRICATE COMPONENTS OF DIES, TOOLS, JIGS, OR FIXTURES Cut and prepare raw material. Block up and establish datum. Machine components of dies, tools, jigs, or fixtures. Heat-treat the Mark the die or tooling Fabricate and assemble sub-assemblies Final fit sub-assemblies die, or tooling Inspect die or tooling fit and functions
7 FABRICATE A PROTOTYPE PIECE PART Develop and organize a prototype buildingplan Produce preliminary sketches of the prototype. Build tooling aids for the prototype. Manufacture the prototype piece part Document the prototype piece part buildingprocess ASSEMBLE AND FINALIZE DIES Read and interpret die drawings and sketches. Set up and operate press. Spot-form the steels and tools. Prepare and form an initial blank. Tool-proof forming stations Finalize the blank shape Prepare and finalize cutting steels Finalize die assembly for final piece part production Try out and trouble-shoot the die Inspect part produced by developed die Final inspect die
COMPETENCY ANALYSIS PROFILE GENERAL MACHINIST 429A. (All unshaded skill sets must be demonstrated/completed)
COMPETENCY ANALYSIS PROFILE GENERAL MACHINIST 429A (All unshaded skill sets must be demonstrated/completed) SKILL SETS SKILLS PROTECT SELF AND OTHERS Identify health and safety hazards. Wear, adjust, and
More informationCOMPETENCY ANALYSIS PROFILE MOULD MAKER 431A (All unshaded skill sets must be demonstrated/completed)
COMPETENCY ANALYSIS PROFILE MOULD MAKER 431A (All unshaded skill sets must be demonstrated/completed) SKILL SETS SKILLS PROTECT SELF AND OTHERS Identify health and safety hazards in the workplace. Wear,
More informationMachinist NOA (2010) Subtask to Unit Comparison
Machinist NOA (2010) Subtask to Unit Comparison NOA Subtask Task 1 Organizes work. 1.01 Interprets documentation. A16 Job Planning 1.02 Plans sequence of operations. A16 Job Planning 1.03 Maintains safe
More informationApprenticeship Training Standard Log Book
Apprenticeship Training Standard Log Book Tool and Die Maker 430A What Is This About? The Apprenticeship Training Standard Log Book identifies all the skills associated with your trade in Ontario. It is
More informationJOB QUALIFICATION STANDARD (JQS)
Occupation: Work Process: Maintenance Mechanic Machine Shop Practical Hours: 250 hrs. JOB QUALIFICATION STANDARD (JQS) DOL Standard: Manual Machining Fundamentals: Apply a working knowledge of metal removal
More informationMachinist NOA (1998) Subtask to Unit Comparison
Machinist NOA (1998) Subtask to Unit Comparison NOA Subtask Task 1 Demonstrates safe working practices. 1.01 Recognizes potential health and safety hazards. A1 Safety in the Machine Shop 1.02 Recognizes
More informationWork Experience Form Machinist
2013 - National Occupational Analysis (NOA) Work Experience Form Machinist 1-877-978-7233 www.manitoba.ca/tradecareers Personal Information (please print) Legal First Name Middle Initial Legal Last Name
More informationInterim Logbook TOOL & DIE MAKER
Interim Logbook TOOL & DIE MAKER Department of Advanced Education and Skills Apprenticeship and Trades Certification Division Note to Apprenticeship Applicants This form can only be used to record hours
More informationName: Machine Tool Technology ( )
Name: Machine Tool Technology (58.0501) Directions: Evaluate the student by checking the appropriate number to indicate the degree of competency. Rating Scale (0-6): 0 No Exposure no experience/knowledge
More informationRevised April Unit/Standard Number. High School Graduation Years 2016, 2017 and 2018
Unit/Standard Number High School Graduation Years 2016, 2017 and 2018 Machine Tool Technology/Machinist CIP 48.0501 Task Grid Secondary Competency Task List 100 ORIENTATION / SAFETY 101 Describe the Occupational
More informationEntry Level Assessment Blueprint Precision Machining
Blueprint Precision Machining Test Code: 4152 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Organization and Shop Practices Demonstrate safe work habits and operating procedures
More informationMachine Tool Technology/Machinist CIP Task Grid
1 Secondary Task List 100 ORIENTATION / SAFETY 101 Describe the Occupational Safety and Health Administration (OSHA) and its role in the machoning industry. 102 Identify & explain safety equipment and
More informationAPPENDIX A TOOLMAKER D.O.T. CODE O*NET CODE As Revised for MACNY, The Manufacturers Association
STATE OF NEW YORK DEPARTMENT OF LABOR APPENDIX A TOOLMAKER D.O.T. CODE 601.280-042 O*NET CODE 51-4111.00 As Revised for MACNY, The Manufacturers Association This training outline is a minimum standard
More informationPennsylvania College of Technology One College Ave. Williamsport, PA Student ID Number:
Pennsylvania College of Technology One College Ave. Williamsport, PA. 17701-5799 Name: School: Student ID Number: Date: COMPETENCY ASSESSMENT FOR MACHINIST GENERAL (MG) MACHINE TOOL TECHNOLOGY (MY) AUTOMATED
More informationMachine Tool Technology/Machinist CIP Task Grid Secondary Competency Task List
1 100 ORIENTATION / SAFETY 101 Describe the Occupational Safety and Health Administration (OSHA) and its role in the machining industry. 2 2 2 1 0.5 102 Identify & explain safety equipment and procedures.
More informationPerkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet
Perkins Statewide Articulation Agreement Documentation item: Secondary Task List Coversheet The Secondary School agrees to: A. Implement the approved PDE Program(s) of Study. B. Provide assessment of student
More informationMachine Tool Technology/Machinist CIP Task Grid
1 100 ORIENTATION / SAFETY 101 Describe the Occupational Safety and Health Administration (OSHA) and its role in the machining industry. 102 Identify & explain safety equipment and procedures. 103 Identify
More informationJOB QUALIFICATION STANDARD (JQS)
Occupation: Work Process: MACHINIST (CNC) CNC Setup Practical Hours: 2000 hrs. DOL Standard: CNC Setup: Apply a working knowledge in the setup of Computer Numerical Controls (CNC) machines that execute
More informationPOS Perkins Statewide Articulation Agreement Documentation Coversheet
POS Perkins Statewide Articulation Agreement Documentation Coversheet Student Name: Secondary School Name: Secondary School Address: CTE Program of Study: CIP # CIP Program Name Grade 9 1. CAREER AND TECHNICAL
More informationComputer Numerical Control (CNC) Machinist POA (2004) Subtask to Unit Comparison
Computer Numerical Control (CNC) Machinist POA (2004) Subtask to Unit Comparison NOA Subtask Task 1 Participates in workplace health and safety practices. 1.01 Maintains a safe workplace environment. 1.02
More informationTotal Related Training Instruction (RTI) Hours: 144
Total Related Training (RTI) Hours: 144 Learning Unit Unit 1: Benchwork and Layout Layout tools Tapping Reaming Filing Engraving Stamping Unit 2: Cutting and Drilling Cutting Operations Drilling Operations
More informationSEMET19 Producing toolroom components using NC/CNC turning machines
Producing toolroom components using NC/CNC turning machines Overview This unit identifies the competences you need to prepare, set up and run numerically controlled (NC) turning machines, computer numerically
More informationMachinist Level 4 Rev. December 12, 2012
Machinist Level 4 Machinist Unit: A14 Reconditioning Level: Four Duration: 12 hours Theory: Practical: 12 hours 0 hours Overview: This unit of instruction is designed to introduce knowledge of the procedures
More informationJob Ready Assessment Blueprint. Precision Machining. Test Code: 4052 / Version: 01. Copyright All Rights Reserved.
Job Ready Assessment Blueprint Precision Machining Test Code: 4052 / Version: 01 Copyright 2009. All Rights Reserved. General Assessment Information Blueprint Contents General Assessment Information Written
More informationACCREDITATION FACILITY AUDIT CHECKLIST
ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Machinist AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours per day: Instructor(s) of Students
More informationJuly 2001 Florida Department of Education CLUSTER CURRICULUM FRAMEWORK. Program Title: Machining Occupational Area: Industrial Education
July 2001 Florida Department of Education CLUSTER CURRICULUM FRAMEWORK Program Title: Machining Occupational Area: Industrial Education Components: One Core, Four Occupational Completion Points Secondary
More informationMachinist A Guide to Course Content
Machinist A Guide to Course Content Machinists work with metals; operate metal-cutting and shaping machinery. Training Requirements: To graduate from each level of the apprenticeship program, an apprentice
More informationStrands & Standards MACHINING 2
Strands & Standards MACHINING 2 COURSE DESCRIPTION This course is the second in a sequence that will use technical knowledge and skills to plan and manufacture projects using machine lathes, mills, drill
More informationCompetency, knowledge and skill areas often offer varying definitions. For purposes of this toolkit, NIMS defines them in the following manner:
Toolkit Roadmap Title of report Credential name Narrative description of credential DEFINITION OF TERMS Competency, knowledge and skill areas often offer varying definitions. For purposes of this toolkit,
More informationCURRICULUM ASSESSMENT CHECKLIST
CURRICULUM ASSESSMENT CHECKLIST Machinist - Level 1 Apprenticeship Manitoba prescribes time and content specific curriculum standards for technical training in the trade of Machinist. To assist accreditation
More informationSetting vertical boring machines for production
Unit 318 Setting vertical boring machines for production UAN: Level: 3 Credit value: 91 GLH: 210 Relationship to NOS: Assessment requirements specified by a sector or regulatory body: Aim: F/600/5423 This
More informationManufacturing Processes (continued)
Manufacturing (continued) Machining Some other processes Material compatibilities Process (shape) capabilities Manufacturing costs Correct pg 142, question 34i should read Fig 6.18 question 34j should
More informationCURRICULUM ASSESSMENT CHECKLIST
CURRICULUM ASSESSMENT CHECKLIST Industrial Mechanic (Millwright) Level 1 Apprenticeship Manitoba prescribes time and content specific curriculum standards for technical training in the trades of Industrial
More informationTurning and Lathe Basics
Training Objectives After watching the video and reviewing this printed material, the viewer will gain knowledge and understanding of lathe principles and be able to identify the basic tools and techniques
More informationThe National Institute for Metalworking Skills, Inc. Duties and Standards For Machining Skills-Level III NIMS/ANSI
The National Institute for Metalworking Skills, Inc. Duties and Standards For Machining Skills-Level III NIMS/ANSI 101-2001 Developed By: Copyright July 1997-Revised September 2001 Distributed by: The
More informationVarious other types of drilling machines are available for specialized jobs. These may be portable, bench type, multiple spindle, gang, multiple
Drilling The process of making holes is known as drilling and generally drilling machines are used to produce the holes. Drilling is an extensively used process by which blind or though holes are originated
More informationTool and Die Maker Level 2
Level 2 B2 Read and Interpret Drawings II Duration: 32 hours 32 hours 0 hours This unit of instruction introduces the Tool and Die Maker Apprentice with the knowledge and skills necessary to read and interpret
More informationNOVA SCOTIA APPRENTICESHIP CURRICULUM STANDARD
NOVA SCOTIA APPRENTICESHIP CURRICULUM STANDARD for the Occupation of Based on the Interprovincial Program Guide (pg. 12 for Program Structure) Machinist New Levels 1, 2, 3 & 4 in September 2014 See Page
More informationTIMTOS 2017 EXHIBITS PROFILE
TIMTOS 2017 EXHIBITS PROFILE Product Code Product Name METAL CUTTING MACHINE TOOL Lathes and Turning Machines 160101 Lathes, Swiss Type 160502 Bench Lathes 160503 High Speed Lathes 160504 Automatic Lathes
More informationMACHINIST TECHNICIAN - LATHE (582)
DESCRIPTION Students will demonstrate technical knowledge and skills to plan, manufacture, assemble, test products, and modify metal parts using machine shop and CNC processes in support of other manufacturing,
More informationMachinist On-the-Job Training Guide
Machinist On-the-Job Training Guide Machinists work with metals and other materials and operate lathes, milling machines and other tools to produce shapes to a required finish and size. Training Requirements:
More informationThe National Institute for Metalworking Skills, Inc. Duties and Standards For Machining Skills-Level II NIMS/ANSI
The National Institute for Metalworking Skills, Inc. Duties and Standards For Machining Skills-Level II NIMS/ANSI 101-2001 Developed By: Copyright July 1997-Revised September 2001 Distributed by: The National
More informationTypical Parts Made with These Processes
Turning Typical Parts Made with These Processes Machine Components Engine Blocks and Heads Parts with Complex Shapes Parts with Close Tolerances Externally and Internally Threaded Parts Products and Parts
More informationMachining I DESCRIPTION. EXAM INFORMATION Items
EXAM INFORMATION Items 50 Points 62 Prerequisites NONE Grade Level 10-12 Course Length ONE SEMESTER DESCRIPTION Students will demonstrate technical knowledge and skills to plan, manufacture, assemble,
More informationCross Peen Hammer. Introduction. Lesson Objectives. Assumptions
Introduction In this activity plan students will develop various machining and metalworking skills by building a two-piece steel hammer. This project will introduce basic operations for initial familiarization
More informationMACHINE SHOP (420) Machine Shop (420)
Machine Shop (420) 2019-2020 1 MACHINE SHOP (420) 420-120. Machine Tool/Fabrication. (2 Credits) This course is designed to provide fabrication students with knowledge and applications of machine tool
More informationTravis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)
Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach
More informationMACHINE TOOLS LAB LABORATORY MANUAL
Vanjari Seethaiah Memorial Engineering College Patancheru, Medak MACHINE TOOLS LAB LABORATORY MANUAL Department of Mechanical Engineering PREFACE Industrial Revolution has given man a lot many luxuries,
More informationSEMMME3-056 Setting single and multi-spindle drilling machines for production
Setting single and multi-spindle drilling machines for production Overview This unit identifies the competences you need to prepare and set up single and multi-spindle drilling machines and associated
More informationManufacturing Processes (2), IE-352 Ahmed M El-Sherbeeny, PhD Spring Manual Process Planning
Manufacturing Processes (2), IE-352 Ahmed M El-Sherbeeny, PhD Spring 2017 Manual Process Planning Chapter Outline 2 1. Introduction 2. Manual Process Planning 3. Process Plan 4. Part Features Identification
More informationMaterials Removal Processes (Machining)
Chapter Six Materials Removal Processes (Machining) 6.1 Theory of Material Removal Processes 6.1.1 Machining Definition Machining is a manufacturing process in which a cutting tool is used to remove excess
More informationDeveloping Skills in Planning and Making a Machined Product
Unit 4: Developing Skills in Planning and Making a Machined Product Unit reference number: Y/600/9140 QCF level: 1 Credit value: 6 Guided learning hours: 60 Unit aim This unit will enable learners to develop
More informationMachining components using vertical boring machines
Unit 319 Machining components using vertical boring machines UAN: Level: 3 Credit value: 77 GLH: 161 Relationship to NOS: Assessment requirements specified by a sector or regulatory body: Aim: Y/600/5430
More informationChapter 22 MACHINING OPERATIONS AND MACHINE TOOLS
Chapter 22 MACHINING OPERATIONS AND MACHINE TOOLS Turning and Related Operations Drilling and Related Operations Milling Machining Centers and Turning Centers Other Machining Operations High Speed Machining
More informationMACHINIST TECHNICIAN - LATHE (582)
DESCRIPTION Students will demonstrate technical knowledge and skills to plan, manufacture, assemble, test products, and modify metal parts using machine shop and CNC processes in support of other manufacturing,
More informationApprenticeship Training Standard. Schedule of Training. Mould or Die Finisher. Trade Code: 277M. Development Date: 2003
Apprenticeship Training Standard Schedule of Training Mould or Die Finisher Trade Code: 277M Development Date: 2003 This document is the property of the apprentice named inside and represents the official
More informationIntroduction to Manufacturing Processes
Introduction to Manufacturing Processes Products and Manufacturing Product Creation Cycle Design Material Selection Process Selection Manufacture Inspection Feedback Typical product cost breakdown Manufacturing
More informationSTATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES
STATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES Articulation Agreement Identifier: _INT 153 (2005-1) Instruction version number (e.g.; INT 100 (2007-1)). Identifier is the postsecondary
More informationBuild a Drill Press Vise
Youth Explore Trades Skills Introduction This activity plan will develop the student s machining and metalworking skills as they fabricate a multi-piece steel vise. The project will encompass basic lathe
More informationAPPLICANT GUIDE ENGINEERING OCCUPATIONS
ENGINEERING OCCUPATIONS OCCUPATION: Fitter - General (ANZSCO 323211) QUALIFICATION: MEM30205 - Certificate III in Engineering Mechanical Trade SKILLS ASSESSMENT - Occupational Requirements A person who
More informationAhsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering
Ahsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering LABORATORY MANUAL For the students of Department of Mechanical and Production Engineering 1 st
More informationProducing and finishing holes using drilling machines
Unit 336 Producing and finishing holes using drilling machines UAN: Level: 3 Credit value: 14 GLH: 56 Relationship to NOS: Endorsement by a sector or regulatory body: Aim: Y/601/2264 This unit has been
More informationIntroduction to Machining: Lathe Operation
Introduction to Machining: Lathe Operation Lathe Operation Lathe The purpose of a lathe is to rotate a part against a tool whose position it controls. It is useful for fabricating parts and/or features
More informationGeneral machining, fitting and assembly applications
Unit 065 General machining, fitting and assembly Level: 2 Credit value: 12 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover a
More informationLathes. CADD SPHERE Place for innovation Introduction
Lathes Introduction Lathe is one of the most versatile and widely used machine tools all over the world. It is commonly known as the mother of all other machine tool. The main function of a lathe is to
More informationCOLLEGE OF ENGINEERING MACHINE SHOP FACILITIES AND PRACTICES Prepared by Mike Allen July 31, 2003 Edited by Scott Morton February 18, 2004
1 COLLEGE OF ENGINEERING MACHINE SHOP FACILITIES AND PRACTICES Prepared by Mike Allen July 31, 2003 Edited by Scott Morton February 18, 2004 I. OBJECTIVE To provide an overview and basic knowledge of the
More informationChapter 23: Machining Processes: Hole Making Part A (Lathe Operations, Boring, Reaming, Tapping)
1 Manufacturing Processes (2), IE-352 Ahmed M El-Sherbeeny, PhD Spring 2017 Manufacturing Engineering Technology in SI Units, 6 th Edition Chapter 23: Machining Processes: Hole Making Part A (Lathe Operations,
More informationGeneral Machining, Fitting and Assembly Applications A/508/5164
Unit Title Ofqual unit reference number (code) Organisation Reference General Machining, Fitting and Assembly Applications A/508/5164 QU051773 Unit Level Level 2 Unit Sub Level None GLH 55 Unit Credit
More informationSEMAE3218 Setting CNC turning machines for production of aircraft components
Setting CNC turning machines for production of aircraft components Overview This standard identifies the competences you need to prepare and set up Computer Numerical Control (CNC) machines or CNC machining
More informationTrade of Toolmaking Module 1: Induction & Bench Fitting Unit 4: Hole Tapping Phase 2
Trade of Toolmaking Module 1: Induction & Bench Fitting Unit 4: Hole Tapping Phase 2 Published by SOLAS 2014 Unit 4 1 Table of Contents Document Release History... 3 Unit Objective... 4 Introduction...
More informationJig and Fixture Design. Chapter 1: Types and Functions of Jigs and Fixtures
Jig and Fixture Design Chapter 1: Types and Functions of Jigs and Fixtures Purpose of Tool Design Objectives: Provide simple, easy-to-operate tools for maximum efficiency Reduce manufacturing expenses
More informationInternational Journal of Science and Engineering Research (IJ0SER), Vol 3 Issue 3 March , (P) X
Design And Optimization Techniques Using In Turning Fixture M Rajmohan 1, K S Sakthivel 1, S Sanjay 1, A Santhosh 1, P Satheesh 2 1 ( UG Student ) 2 (Assistant professor)mechanical Department, Jay Shriram
More informationMACHINE TOOLS; METAL-WORKING NOT OTHERWISE PROVIDED FOR
XXXX B23 MACHINE TOOLS; METAL-WORKING NOT OTHERWISE PROVIDED FOR XXXX PLANING; SLOTTING; SHEARING; BROACHING; SAWING; FILING; SCRAPING; LIKE OPERATIONS FOR WORKING METAL BY REMOVING MATERIAL, NOT OTHERWISE
More informationDEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK ME6402 MANUFACTURING TECHNOLOGY II UNIT I PART A 1. List the various metal removal processes? 2. How chip formation occurs in metal cutting? 3. What is
More informationPreparing and using CNC machining centres
Unit 017 Preparing and using CNC machining centres Level: 2 Credit value: 14 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover
More informationCourse Title: Advanced Manufacturing Technology MACH 110 Instructor: Conrad Mercurius Contact Information: Conrad.Mercurius@raritanval.edu Course Meeting Dates, Days, and Times: Total # hours: 250 Course
More informationChapter 23. Machining Processes Used to Produce Round Shapes: Turning and Hole Making
Chapter 23 Machining Processes Used to Produce Round Shapes: Turning and Hole Making R. Jerz 1 2/24/2006 Processes Turning (outside surface) straight, taper, facing, contour, form, cut-off, threading,
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationMachinist--Cert Students apply industry standard safety practices and specific safety requirements for different machining operations.
MTT Date: 09/13/2018 TECHNOLOGY MTT Machine Tool Technology--AA Students apply industry standard safety practices and specific safety requirements for different machining operations. Students calculate
More informationInterprovincial Program Guide. Machinist. Human Resources and Skills Development Canada. Ressources humaines et Développement des compétences Canada
Interprovincial Program Guide 2012 Machinist Human Resources and Skills Development Canada Ressources humaines et Développement des compétences Canada Interprovincial Program Guide Machinist 2012 Trades
More informationPERIYAR CENTENARY POLYTECHNIC COLLAGE Manufacturing Technology - II SUBCODE: MEB520 UNIT- I PART-A
PERIYAR CENTENARY POLYTECHNIC COLLAGE Manufacturing Technology - II 1. List out the cutting tool materials. 2. Define rake angle. 3. Define clearance angle. 4. What is meant by drilling? 5. What is the
More informationVALLIAMMAI ENGINEERING COLLEGE DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK ME6402 MANUFACTURING TECHNOLOGY II UNIT-I PART A 1. List the various metal removal processes? (BT1) 2. Explain how chip
More informationC O M P E T E N C Y A L I G N M E N T
S C A N S C O M P E T E N C Y A L I G N M E N T -ROP COURSE: MACHINIST/PRE-EMPLOYMENT ROP NO. 29-40-89 SCANS COMPETENCIES BASIC SKILLS READING, WRITING, ARITHMETIC, MATHEMATICS, LISTING, AND SPEAKING.
More informationVCE VET ENGINEERING STUDIES CERTIFICATE II
Victorian Certificate of Education 2009 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET ENGINEERING STUDIES CERTIFICATE II Written examination Section Wednesday 18
More informationPreparing and using CNC Machining Centres F/508/4727
Unit Title Ofqual unit reference number (code) Organisation Reference Preparing and using CNC Machining Centres F/508/4727 QU051501 Unit Level Level 2 Unit Sub Level None GLH 64 Unit Credit Value 14 Sector
More informationSyllabus: Basic Manual Machining
Syllabus: Basic Manual Machining Subject Code: 172302 Course Number: GM9006 CIP Code: 48.0501 SOC Code: 51-4041 C-TEC of Licking County 150 Price Road Newark, Ohio 43055 Instructor: Bob Bronkar Instructor
More informationRoll No. :.. Invigilator s Signature :.. CS/B.Tech (ME)/SEM-5/ME-504/ TECHNOLOGY OF MACHINING. Time Allotted : 3 Hours Full Marks : 70
Name : Roll No. :.. Invigilator s Signature :.. CS/B.Tech (ME)/SEM-5/ME-504/2009-10 2009 TECHNOLOGY OF MACHINING Time Allotted : 3 Hours Full Marks : 70 The figures in the margin indicate full marks. Candidates
More informationNTMA-U Web-based module training
NTMA-U Web-based module training Modules are self-paced and interactive. Each module takes approximately 30-40 hours to complete. Instruction includes quizzes to progressively test the user s understanding.
More informationOroville Union High School District Industrial Technology
Oroville Union High School District Industrial Technology Industrial Technology - ROP Fabrication ROP Fabrication COURSE TITLE: ROP Fabrication LENGTH OF COURSE: One Year (2 hours per day) GRADE LEVEL:
More informationno mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side
Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable
More informationManufacturing Science-II (EME-503)
Time: 1 Hour B.Tech. [SEM V (ME-5 All Groups)] QUIZ TEST-1 Manufacturing Science-II ` Max. Marks: 30 Note: Attempt all the questions Q1) How metal is removed in metal cutting? Explain by giving any simple
More informationCARIBBEAN EXAMINATIONS SECONDARY EDUCATION CERTIFICATE EXAMINATION MECHANICAL ENGINEERING TECHNOLOGY. Paper 02 - Technical Proficiency.
FORM TP 2011094 CARIBBEAN EXAMINATIONS SECONDARY EDUCATION CERTIFICATE EXAMINATION TEST CODE 01335020 COUNCIL MECHANICAL ENGINEERING TECHNOLOGY Paper 02 - Technical Proficiency 2'h hours MAY/JUNE 2011
More informationTotal Related Training Instruction (RTI) Hours: 144
Total Related Training (RTI) Hours: 144 Learning Unit Unit 1: Specialized CNC Controls Fanuc Haas Mazak Unit : CNC Programming Creating a CNC Program Calculation for Programming Canned Cycles Unit : CNC
More informationNow you are only cutting a groove in the lower half of the receiver, if your 46
The picture on the left shows the shape of the cutter that I ground. The picture on the right shows a picture of a cut off tool replaceable cutting bit that I used as a pattern to grind my own cutter.
More informationHOME WORKSHOP HANDBOOK Rugged BENCH GRINDER. By JOEL B. LONG
6 HOME WORKSHOP HANDBOOK Rugged BENCH GRINDER W By JOEL B. LONG ITH this bench grinder you can keep your cutting tools sharp and do general offhand grinding, and can, with the aid of various attachments,
More informationSEMPEO SQA Unit Code FP27 04 Producing components using hand fitting techniques
Producing components using hand fitting techniques Overview This standard covers a broad range of basic hand fitting competences that will prepare you for entry into the engineering or manufacturing sectors,
More informationFORM TP MAY/JUNE 2007
TEST CODE 01335020 FORM TP 2007107 MAY/JUNE 2007 CARIBBEAN EXAMINATIONS COUNCIL SECONDARY EDUCATION CERTIFICATE EXAMINATION MECHANICAL ENGINEERING TECHNOLOGY Paper 02 - Technical Proficiency 2 -y hours
More informationProducing components using hand fitting techniques
Unit 005 Producing components using hand fitting techniques Level: 2 Credit value: 14 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required
More informationSTATE UNIVERSITY OF NEW YORK SCHOOL OF TECHNOLOGY CANTON, NEW YORK
STATE UNIVERSITY OF NEW YORK SCHOOL OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 121 - MANUFACTURING PROCESSES I Prepared By: Daniel Miller Updated By: Daniel Miller (April 2015) CANINO SCHOOL OF
More informationBig Sandy Community and Technical College. Course Syllabus
Big Sandy Community and Technical College Course Syllabus PS Number: 81212 Semester: Spring Year: 2017 Faculty Name: Charles K. Moore Title: Associate Professor Course Prefix and Number: IMT-116 Course
More information