ROTJ Hero Boba Fett Build
|
|
- Clarissa Randall
- 5 years ago
- Views:
Transcription
1 ROTJ Hero Boba Fett Build
2 Armor The armor used for the project was made by Bobamaker. This included the Shoulders, Chest Plate and Diamond, Ab Plate, Crotch and Butt Plate, Back Plate and Knees. The knee launchers are also Bobamakers. They are made of alluminium. The gauntlets were made by RS Propmasters The armour was already primed by Bobamaker. A base coat of Humbrol Silver 11 was used. Stencils created by Rafalfett on The Dented Helmet were used to mimic the battle damage. Maskol is used to highlight the areas where the silver colour will appear on the armour. The Rafalfett stencils below show where the silver is placed. Comparisons can be made against the photos above. Note: The Rafalfett stencil for the back plate is too large include in this document. I have copied and pasted below the completed colours for the backplate. You can easily identify the silver areas here
3 Armor (cont.) On the chest plates, & diamond, collar plate, cod piece & butt plate and back plate, the next colour to be used is Humbrol Yellow 81. Rather then spraying the entire armor with Yellow 81, I just sprayed it in areas where I knew the yellow appears on the armor. I then used the maskol again over the yellow areas. This meant in some cases I was masking over masking fluid that was already used on the silver areas. The photos below show were the yellow will be placed on the armour. The masking fluid that is over the yellow paint is the area that will be protected before the next colour is applied
4 Armor (cont.) The diagrams below show exactly where the yellow is to be applied on the armour. These diagrams can be crossed referenced with the photos on the preceding page. One the maskol on the yellow paint dried the final coat went over all of these pieces. The colour used was Humbrol 78. When the paint cured over 24 hours, the maskol was then removed to expose the layered effect below. The photos below are compared to the final Rafalfett designs
5 Armor (cont.)
6 Armor (cont.) The knees were tackled next. The colours used for the knees were Humbrol 11 Metallic Silver, Humbrol 103 Yellow, Humbrol 154 Yellow and a light misting of Humbrol 82 Orange. The same layered technique was used as the armor using maskol on each layer and peeling everything off when the painting was finished. Below you can see some progress photos Knees with Launchers and Shoulder with Tattoo Rafalfett Designs
7 Armor (cont.) I purchased the gauntlets from a member of the Dented Helment (Hames14). The only things I had to do with the gauntlets myself was to add the hoses. They were soaked in coffee for a week to give a stained appearance. I measured out the hoses so they were the right size from the arm to the shoulder. I drilled holes through each hose and threaded through key ring rings through each hole. I then connected them to a female belt connecter. The male belt connector is sewn into the shoulder sleeve of the flight suit. The final two photos above show the stained hoses and the placement of the functioning LED on the right gauntlet
8 I researched the ROTJ helmet for months on TDH. It was important for me to get the colours right and to find the right stencils to get the helmet as accurate as possible. After a huge amount of research on what was right and what was wrong I decided to go for the paint chart below that is on TDH. Once again I decided to use the Rafalfett Stencils for the helmet. An enormous amount of research has gone into the Rafalfett stencils and so many helmets across the world have been made using these stencils I came to the conclusion that these stencils are the definitive version of the ROTJ Helmet With regard to the colours used on the helmet, I didn t deviate from a single Humbrol colour on the paint charts on this page and the following page
9 With regard to the painting technique, everything was airbrushed. The only exception was the red dental files which were hand painted and a little touching up on the kill stripes. I used a layering technique which I will go over on the next few pages. I started with the back panels, followed by the dome, the lower cheeks, the upper cheeks, the mandibles and finally the keyslots at the back. Once again I used the layering technique and once again I painted liquid maskol over maskol. It had proven effective on my armor so I planned to use the same technique again
10 As mentioned before the Bobamaker helmet was already primed which meant I just had to get my base coat down first which was Humbrol 11 Metallic Silver. I then follwed the stencils and used maskol to protect the areas that I wanted to remain silver I left the maskol for a couple of hours and once ready I sprayed the back panels with the next colour which was Humbrol Gunmetal 53
11 The next layer of paint was grey 67. Unfortunately I forgot to take a phot of the maskol but you can see below the stencils used and on the following page you can see the end result with all three colours visible under the green paint
12 Once all the masking had been completed over the final colour, I was then able to apply the final coat which was a mix of two colours. Humbrol Green 131 & Humbrol Green 76 Ratio 1:1. I left the paint cure for 24 hours and removed the maskol I moved on to the dome then. I covered the rest of the helmet to protect it from overspray. I had already painted the entire helmet Humbrol Metallic Silver so I just need to use my maskol again to protect the areas I wanted to remain silver. I used Rafalsfetts stencils for this as a guide but I also used the colour paint chart as a guide also. The Rafalfett stencil is 22 pages long so for the purposes of this presentation I will include the Humbrol Paint by numbers colour chart as a guide. Below are some photos of the paint job on the dome with the usual masking tecnique. Colours used are all identicla to what is on the paint by numbers chart
13 For the kill stripes I once again maked up and used maskol for the battle damage. The colour used for the battle damage was Humbrol Orange 82 Once the kill stripes were completed I then used the Rafal Fett stencils to do the upper and lower cheeks. The upper cheeks were sprayed black with Humbrol 33. Then misted with grey 79 and green 78. The lower cheeks were grey 31 and green 78. Damage was with grey 79, grey 67 and grey 31 Mandibles, rim around the helmet and key slots were all tackled next. Once again the masking technique was used again. Everything was already painted earlier Humbrol Metallic Silver 11. The other main colours used were Humbrol Red 73 & Humbrol Red 100 Mixed at a ratio 1:1. Gunmental 53 and Grey 79. Below are the Rafal Fett stencils and the areas masked by maskol for the silver damage
14 The final two colours are added to the mandibles, the grey and the final red. When the paint is fully cured the maskol was peeled off. Below are the Rafal Fett Stencils and the final photos of the completed mandibles The helmet rim is tackled next. Silver Humbrol 11 is already on the rim so maskol is placed on the areas that I want silver to remain on the rim. Below are the Rafalfett stencils where the silver is masked.
15 The next colour is grey is grey 79. As usual maskol is placed on the areas where I want to protect the grey. Once the paint is cured over 24 hours the final red colour is applied to the rim The completed rim with the actual helmet along with Rafal Fett Stencils
16 Finished Helmet
Designs by Jude. Metro Coat. for 19 Mortimer. $12.95 US
www.fletcherpatterncompany.com Metro Coat for 19 Mortimer $12.95 US 2013, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use. Metro For 19 Mortimer Mort Basic Instructions You will
More informationTime to start something new. I was actually having another go at finishing the Ford GT Matech from Simil R, but frustration with the complete lack of
Time to start something new. I was actually having another go at finishing the Ford GT Matech from Simil R, but frustration with the complete lack of locators made me put it back into the box. I decided
More informationBlakes 7 DSV-1 Liberator
Blakes 7 DSV-1 Liberator Model kit by Masterpiece Models: www.masterpiecemodels.com Pattern Maker: Alfred Wong Casting: J&S Technologies LLC Parts List Main body 3 Main body nose vanes 4 Main body detail
More informationI found the job quite straightforward and would have done it in about half an hour if I hadn t kept stopping to take pictures and write notes.
SmartStart Installation The following describes how I installed a Dometic SmartStart Model #4220040 on the Dometic 600312.331 Penguin Air Conditioner on my Escape 19 Trailer. I had no problems following
More informationGTS Music diy-guitar.com
GTS Music diy-guitar.com Tele Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning to build your guitar
More informationBY SEAN MIDDLETON V 4. Instructions courtesy of TopNotch Page 1
BY SEAN MIDDLETON V 4 Instructions courtesy of TopNotch Page 1 INSTRUCTIONS INTRODUCTION Using masks take a little bit of practice and some patience when you first begin. Like most things though, once
More informationGTS Music diy-guitar.com
GTS Music diy-guitar.com IB Jem Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning in order to have
More informationSo, let s get started painting ourselves a vampire queen!
I have always loved vampires and for this build I wanted to do something special. The sculpt was outstanding with nice details and almost no filling. Karol Rudyk s sculpture was based on a picture and
More informationmickyd Gold Member The chuck that came with my ER was frozen solid...
http://wwwshopsmithnet/forums/showposthtm?p=46842&postcount=200 Page 1 of 7 View Single Post Thread: Restoration Progress On My 1952 ER10 09-13-2009, 12:19 AM #200 mickyd Gold Member Join Date: Feb 2009
More informationGTS Music diy-guitar.com
GTS Music diy-guitar.com SG Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning to build your guitar
More informationHasegawa 1/48 scale Nakajima B5N2 "Kate" by Dick Smith
Hasegawa 1/48 scale Nakajima B5N2 "Kate" by Dick Smith The release of last summer's motion picture "Pearl Harbor," caused a flood of interest in the modeling world in the Japanese aircraft that took part
More informationMr. & Mrs. H. Dumpty
Mr. & Mrs. H. Dumpty 2004 Robyn R. Warne All Rights Reserved. Page 1 of 6 Mr. & Mrs. H. Dumpty List of supplies 2 - unfinished wood eggs 2 - unfinished wood egg cups gesso JW etc. Right Step Sealer sandpaper
More informationInstallation Instructions for Lambo Door Mechanism. 1. Lift the hood and remove left and right shield of front wheel.
Installation Instructions for Lambo Door Mechanism 1. Lift the hood and remove left and right shield of front wheel. 2. With the door open pull out the rubber hose connecting the door and the door frame,
More informationMISCELLANEOUS PICTURES and THINGS
MISCELLANEOUS PICTURES and THINGS Acres of sod to fly on north of Pasco, WA, about 65 miles from Walla Walla. This is a wonderful site for weekend flying and contests. It s been the location for several
More informationSwift assembly guide
Swift assembly guide Download the assembly guide at www.scihighmodels.com/swift.pdf Sample kit shown with aluminium bells (available with the Deluxe kit) Shown here without main tanks Version 10/12/2010
More informationConverting a Bachmann Class 45 model to 45133
Converting a Bachmann Class 45 model to 45133 Bachmann have yet to produce an accurate OO gauge model of a Class 45/1. The 45/1s that have been produced were let down by the presence of steam heat details
More informationTip: Walter s LED Lighting Project for Faller Hot Air Balloon Date:
Introduction I take great pleasure in introducing Walter s first article to be posted in my Tips section of my web pages. All text and photos are by Walter unless specified. Ross Photo by Ross Walter s
More informationINSTRUCTION MANUAL T100 MINI-MIST DELUXE TANNING SYSTEM. (Not Suitable for Continuous Use)
INSTRUCTION MANUAL T100 MINI-MIST DELUXE TANNING SYSTEM (Not Suitable for Continuous Use) DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please
More informationINSTRUCTION MANUAL HAPPY-MIST TANNING SYSTEM. (Not Suitable for Continuous Use)
INSTRUCTION MANUAL HAPPY-MIST TANNING SYSTEM (Not Suitable for Continuous Use) DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these
More informationWETROOM WALK-IN TWIN ENTRANCE AWT1500 AWT1200 AWT900
WETROOM WALK-IN TWIN ENTRANCE AWT500 AWT00 AWT900 INSTALLATION PARTS LIST 5 AF /6 IMPORTANT Before disposing of carton and/or commencing assembly, please check all the parts to ascertain that none are
More informationGTS Music diy-guitar.com
GTS Music diy-guitar.com Strat Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning in order to have
More informationFrom "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES
From "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES Carl Ford I have found most commercially available tool handles uncomfortable
More informationFIREMAN S SUIT FOR YOUR DOLL. 1.FiremansSuit.10181
FIREMAN S SUIT FOR YOUR DOLL www.knittingfordolls.com sales@knittingfordolls.com 1.FiremansSuit.10181 FIREMAN S SUIT FOR YOUR DOLL Pattern fits any 18 dolls like American Girl dolls Pattern is for Advanced
More informationNanton Grain Mill Assembly
( 1 ) Nanton Grain Mill Assembly Locate package for assembling storage building. These are cut from 1/8 masonite. Inspect and lightly sand edges where it will be bonded. Use white glue or CA glue to bond.
More informationELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS Lesson 13 EET 150 Electrical Connections Learning Objectives In this lesson you will: see different methods of making electrical connections. learn a procedure for making soldered
More informationTaco Bell Restaurant kit in HO scale
Taco Bell Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic, clear window glazing, Plastruct tile roofing, and logo
More informationMale Cable Connectors / Female Receptacles Male cable connector straight, with internal strain relief clamp and/or clamping ring, cable diameter 6-12,5 mm No. of contacts 3 + PE 3 + PE Termination technique
More informationWEEK 4 COMPLETE SIDING & EXTERIOR PAINTING
WEEK 4 COMPLETE SIDING & EXTERIOR PAINTING INSTALL DRY WALL CLIPS (STAFF) Safety Briefing Complete siding Caulk exterior plumbing & electrical boxes First Coat Exterior Second Coat Exterior Install siding
More informationJungle Club Dinosaurs #80019 / 27 Designs
Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale
More informationFor a professional approach to your sign needs, consult a professional team.
POST MOUNTED SIGN SYSTEMS INTRODUCTION FIRST IMPRESSIONS When attracting new custom, your Company sign is often the primary thing to be noticed, so first impressions are paramount. Location, design, colour
More informationMaterial Used Article Number Quantity
Instruction S019K009 Concrete Etagere 1. Etagere Material Used Article Number Quantity Metal Etagere Construction Kit Classic, approx. 330 mm, handle approx. ø 45 x 5 mm, silver coloured, 9 parts Casting
More informationHardee s Restaurant kit in HO scale
Hardee s Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic and laser cut white acrylic, clear acrylic window glazing,
More informationHome Haunters Haven. STALKER COSTUME
Home Haunters Haven http://www.homehauntershaven.com/stalker.htm STALKER COSTUME Construction is fairly simple. See below for the pictures. Basically, all you need are the following: 1. A good hiking backpack
More informationseasons Lethaby Umbrellas - brought to you by 4 Seasons
seasons Lethaby Umbrellas - brought to you by 4 Seasons seasons 4 Seasons is proud to supply Lethaby outdoor umbrellas to complement its outdoor furniture collection. Lethaby offers a range of fabric,
More informationGive one or two examples of electrical devices that you have personally noticed getting warm when they are turned on.
Resistors We begin by learning how to read the values of resistors and to measure the values using a digital multimeter (DMM). Resistors are the most common and simplest electrical component. In an electrical
More informationby Dave Lesko Thanks, Detective, for making us look good.
by Dave Lesko Dave Lesko is a detective in a large police department just outside of Chicago. There are only two things that rival his enthusiasm for his family: the Chicago Bears, his job and monster
More informationPreparation. How to make a monk happy!! materials used in this step-by-step. We start by preparing our miniature.
Preparation materials used in this step-by-step How to make a monk happy!! We start by preparing our miniature. First of all we need to clean the model from all its moldlines then glue the main elements
More informationChemical Etching A guide for sign designers and sellers.
A guide for sign designers and sellers. This guide is intended to explain the etching process and some of the techniques that we use so that you can design the best possible etched signs for your customers
More informationKiss the Cook. by MaryJo Tuttle. Copyright 2008 MaryJo Tuttle and Crafts Americana Group, Inc. All Rights Reserved. *A331388* No.
Kiss the Cook by MaryJo Tuttle Copyright 2008 MaryJo Tuttle and Crafts Americana Group, Inc. All Rights Reserved. No. *A331388* Kiss the Cook By MaryJo Tuttle Palette: DecoArt Americana Acrylics Bleached
More informationSPRAY GUN. MODEL NO: TG2 PART No: OPERATION & MAINTENANCE INSTRUCTIONS
SPRAY GUN MODEL NO: TG2 PART No: 3090070 OPERATION & MAINTENANCE INSTRUCTIONS 0803 - 1 - - 14 - NOTES Please read these instructions carefully before operating the tool Thank you for purchasing this CLARKE
More informationSentinel Armor Kit Assembly Guide
1 Sentinel Armor Kit Assembly Guide 2 Thank you for purchasing the Mynock s Den Collection Sentinel Armor Kit by Vader s Vault. This guide will help you assemble your new kit, so be sure to keep it close
More informationMulti-Bowl Applications
Multi-Bowl Applications Standard Off-the- Shelf Casing Head Lower Profile Solution Common Support Bushing Field Proven Sealing Designs FS Seals require No Plastic Packing C-22 Profile = Standard Off-the-
More informationTIP TIP - HOTWIRE WP 20 SC TORCH. Materials: Steel/Stainless/Aluminum Duty Cycle: 280A / 100%
TIP TIP - HOTWIRE WP 20 SC TORCH Materials: Steel/Stainless/Aluminum Duty Cycle: 280A / 100% COMPLETE TORCH ASSEMBLY 20002480 TIP TIG WP 20 FLEX HEAD SC TORCH ASSY WITH ORANGE LINER (14ft) 20002483 TIP
More informationAXIS P32 VE/-LVE Series. Repainting Instructions
Repainting Instructions Impact on warranty Impact on warranty This product is approved for repaint by Axis, provided that you follow the instructions in this document and at www.axis.com/warranty-implication-when-repainting
More informationShay - Boiler Cosmetics - Part III
The task here is to finish the domes. Shay - Boiler Cosmetics - Part III Nelson Riedel Nelson@NelsonsLocomotive.com Initial:4/14/04 Last Revised: 06/06/2004 http://www.nelsonslocomotive.com/shay/boiler/boilercosmeticsiii/boilercosmeticsiii.htm
More informationHYDRAULIC MOWER AHRM4H, HRM48H Parts Catalog INDEX HOME TRACTOR ATTACHMENTS APPLICATION CHART
R Ingersoll HYDRAULIC MOWER AHRM4H, HRM48H Parts Catalog 8-3091 HOME TRACTORS ATTACHMENTS PAINT GENERAL INFO INDEX Deck. Belt and Idler Pulley...5 Mounting Bracket...7 Rear Wheels...7 Hydraulic Drive...9-13
More informationGet Started: Paint Area
Colouring & Airbrushing Gunilla Matteau Get Started: Paint Area Dust free area! Table Cover table & floor with plastic sheet to protect from paint spills Good lighting (full spectrum like daylight) to
More informationVogue DIY. Armée Suisse
Vogue DIY Armée Suisse Modern twist on the classic patched jean jacket. Attach bullion, sequin, vintage, beaded and glitter patches to create a one-of-a-kind piece. What s Needed: Swiss Jean Jacket- swisslink.com
More informationPaint Spraying: Spray gun parts Student A:
Paint Spraying: Spray gun parts Student A: You need to replace some parts for your spray gun. However, you don t know the name of the part, or the part number. Telephone a paint gun supplier and order
More informationMaxiMist Pro Series Spray Gun
MaxiMist Pro Series Spray Gun Your purchase includes the MaxiMist Pro Series Spray Gun Please read these instructions carefully and keep for your reference. Refer to the included instruction manual as
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationAssembly Instructions
Assembly Instructions Parts Included: 1 Nose Cone 1 Body Tube 3 1/8 Balsa Fins 1 Thrust Ring 1 Motor Tube 1 Motor Hook 1 Motor Sleeve 2 Centering Rings 1 Launch Lug 1 Kevlar Shock Cord (yellow) 1 Elastic
More informationGetting Started with Tunics
Getting Started with Tunics Scene from the Bayuex Tapestry, early 11th Century Introduction One of the first things you will need to do now that you have decided to become involved in the SCA is to get
More informationBuilding Gundam Models: Advanced Panel. Intros Simple tricks to improve finish Perfect finish! Make it shine! Now Break it!
Building Gundam Models: Advanced Panel Intros Simple tricks to improve finish Perfect finish! Make it shine! Now Break it! Contests http://angelmex.net Using glue Using glue in some key sections in the
More informationTrack Bumpers Wood or Plastic Your Choice
Track Bumpers Wood or Plastic Your Choice An assembly method is presented to build track bumpers for non-ballasted track such as Atlas O 2st Century, Ross Custom, Gargraves etc. Whether you decide to build
More informationMain Components. Pipe and Bolt Threading Machine 300/300A. Early Style. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine 00/00A Main Components Early Style 0 0 * 0 0 0 For Information on Cutters, Die Heads and Reamers SEE INDEX Ref. 0 0 Catalog 0 00 00 0 0 0 00 0 0 0 0 0 0 0 00 0 00 00 00
More informationSGTalon s Enterprise-A Foamie Build Guide. SGTalon s. Enterprise. Enterprise--A. Assembly Instructions
SGTalon s Enterprise SGTalon s Enterprise--A Enterprise Assembly Instructions Page 1 4-13-2013 SGTalon s Enterprise *******Recommended Hardware******** 2.6oz 250w Motor and Speed Control with 8x6 prop
More informationScratchbuilding a HO Semphore Signal-With Addendum. Paul Allard Dana Brown December 10, 2017 Green Mountain Division - NMRA
Scratchbuilding a HO Semphore Signal-With Addendum Paul Allard Dana Brown December 10, 2017 Green Mountain Division - NMRA Background Avoiding cornfield meets on obscure single track mainline. Semaphore
More informationStudio Face Xtreme 6020 Installation Instructions (Nickel , Black )
Packing List Face Trim (4 Pieces) (3) Hanging Brackets (9) 3/16 x 1-1/4 Masonry Screws 9/64 Drill Bit Compatibility (2) Lower Brackets w Magnets (2) Lower Facing Plates (4) 2 Drywall Screws Trim Hardware
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationHANDHOLE SEAT GRINDER
1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
More informationJulia by. #Julia 1/11
Julia by / Julia by XS - XXXL For those who adore showing off something unique, we ve created a long version of the Julia kimono. The light and airy fabric and the side slits lend it a touch of elegance
More informationCentral New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
More informationWash it, don t toss it! Let us wash your garments! Outerwear Garments. Product Catalogue
Wash it, don t toss it! Let us wash your garments! Outerwear Garments Version: January 1, 2017 High Visibility and Enhanced Visibility Insulated Parkas High Visibility Note: Coat alone is CSA-Z96-15 Compliant
More informationPlumbing Part II - Hand Pump
Plumbing Part II - Hand Pump Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 7/17/03 Last Revised: 06/06/2004 The hand pump located in the tender water tank is a backup pump should the axel pump fail
More informationor clippers to clean the mould lines and flash off the figures.
In the first of a series of articles aimed at the newbies of wargaming Dave Robotham gives us an insight into his painting methods. This article looks at 10mm scale British WWII armour and infantry from
More informationQuantum 2 SQUARE 0605
Installation Instructions #CH-S-0605-KIT #CH-S-0605-2FT #CH-S-0605-4FT #CH-S-0605-6FT #CH-S-0605-8FT Custom #CH-S-0605 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Cut Length Chart Pg. 7 Recessed
More information3DR ArduCopter Quad-C
3DR ArduCopter Quad-C 3DR ArduCopter Quad-C Thank you for purchasing a 3DR ArduCopter Quad kit. The 3DR ArduCopter Quad is a stable and supported multi-rotor frame in the ongoing development of the ArduCopter
More informationEmbroidery Floss: To match cuff, black, red, and to match doll's dress. 2 Rusty bells (medium size) or use rusting recipe below
Approximately 18 inches tall You Will Need: Material: Material for stocking and cuff. Scraps of muslin, tea-dyed muslin, brown flannel (gingerbread man), material for snowman's hat & scarf, doll's dress,
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationHercules Ninth Labor: Hippolyte s Belt. By: Molly Cummings and Sarah Neuschotz
Hercules Ninth Labor: Hippolyte s Belt By: Molly Cummings and Sarah Neuschotz Hippolyte Hercules needed to get the belt of Hippolyte and bring it back to King Eurystheus.This belt was not an ordinary belt,
More informationby Conny Valentina Thanks, Conny, for making Black Heart look good.
by Conny Valentina Conny Valentina is one of our down under GK sisters and living in Adelaide, Australia. She is an artist by trade and works mainly in 2D art, always in traditional media. She started
More informationMetallic Pumpkin Centerpiece INSTRUCTIONS MATERIALS. Posh pumkins put fun front and center! SKILL LEVEL: PROJECT TIME: 2 HRS. by Jenni Radosevich
Metallic Pumpkin Centerpiece by Jenni Radosevich Posh pumkins put fun front and center! PROJECT TIME: HRS Krylon Fusion All-In-One Paint + Primer Metallic Silver, Metallic Copper Krylon Glitter Blast Silver
More informationUsing Gimp to Fix Chain Shirt 5: An armor reskinning tutorial for NWN2 by Barrel of Monkeys Version 1: July 7, 2008
Using Gimp to Fix Chain Shirt 5: An armor reskinning tutorial for NWN2 by Barrel of Monkeys Version 1: July 7, 2008 This tutorial will walk a beginner through the steps of modifying the textures of an
More informationGentleman s Suit. for 17 Super Hero. Tamara Casey. Designed by. Super103 $12.95 US
www.fletcherpatterncompany.com Gentleman s Suit for 17 Super Hero Designed by Tamara Casey Super103 $12.95 US 2010, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use. Gentleman s
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationAMRIT INDO CANADIAN ACADEMY HOLIDAYS HOMEWORK ART & CRAFT VI th
AMRIT INDO CANADIAN ACADEMY HOLIDAYS HOMEWORK ART & CRAFT 2018-19 VI th Let us Make an Apron Required matrial:- Cottpn Fabric(check print) - 1 yard is ample. Thread and sewing machine. Step 1. Cut the
More informationBABY CELESTIAL APPLIQUÉS
BABY CELESTIAL APPLIQUÉS Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in
More informationTIP TIP - HOTWIRE WP 20 SC TORCH. Materials: Steel/Stainless/Aluminum Duty Cycle: 280A / 100%
TIP TIP - HOTWIRE WP 20 SC TORCH Materials: Steel/Stainless/Aluminum Duty Cycle: 280A / 100% COMPLETE TORCH ASSEMBLY 10002480 TIP TIG WP 20 FLEX HEAD SC TORCH ASSY WITH ORANGE LINER (14ft) $995.00 ea.
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More informationOne Orkla Work Wear Edition. Clothing Catalogue
1 One Orkla Work Wear Edition Clothing Catalogue 25.05.2015 Colour coded size markings In order to easily distinguish the different sizes of apart it used different colors of thread: on the collar of the
More informationLG BENIF characteristics
LG BENIF characteristics Over 500 Patterns Interior Applications Class A Fire Rated (UL-723) as well as being rated for Fire Door Applications Repairable Stain & Solvent Resistant Minimal Down Time Flexible
More informationHow to assemble the Reims Gueux Pit Centre Module #005
How to assemble the Reims Gueux Pit Centre Module #005 We recommend quick drying super glue for our models. Just a few drops on the joining edges, press and hold them for a few seconds and the connection
More informationHow to Sew Your Mini Doll Costumes
How to Sew Your Mini Doll Costumes These instructions tell you how to sew up costumes for a mini doll using the Mini Doll Costumes swatch from the sherralynsdolls shop on Spoonflower https://www.spoonflower.com/profiles/sherralynsdolls.
More informationI m going to say that Rob coerced me to take part in the club Shell 4000 theme build. He promised me an engine free Tamiya kit. This is what I got
I m going to say that Rob coerced me to take part in the club Shell 4000 theme build. He promised me an engine free Tamiya kit. This is what I got instead. Looks like it s an older Fujimi kit and it does
More informationApplication Guide for Jotun Primax Diamond Powder Coatings
for Jotun Primax Diamond Application Guide for Jotun Primax Diamond Powder Coatings Date of Last Revision: August 2017 Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview 3 3.0 Safety Considerations..3
More informationBuilding a Vailly Aviation Hawker Hurricane...Instalment 10
Building a Vailly Aviation Hawker Hurricane...Instalment 10 Painting: I am a lousy painter of model aeroplanes, anybody looking for a few clues from this section of the build is well advised to look elsewhere.
More informationIEC 2009 Paper Dolls - Campbell - Color Chart
IEC 2009 Paper Dolls - Campbell - Color Chart This Paper Doll Collection has embroidery designs that will fit embroidery machines with 4x4- or 5x7-inch hoop sizes. Embroidery designs in the 5x7" sizes
More informationBy Erich Fritz.com G -MA.AB www 39
By Erich Fritz 39 I have been airbrushing seriously for the last five years. I am mainly self-taught, aside from the few videos I do own. I love to read AB-Mag to learn new skills and techniques. At this
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationMaterial Packing Brown Grey Pine Black White
RTA Connectors Minifix Zinc alloy For housing: 12 or 18 Bolt hole: Ø 7 or 8, depending on choice of connecting bolt Drilling distance B: Distance from centre of Minifix housing to shelf front edge (24
More information3M Spray Equipment Products Automotive Refinish Applications. Effective, Efficient. Economical
3M Spray Equipment Products Automotive Refinish Applications Effective, Efficient Economical Key Benefits of using the 3M PPS Paint Preparation System Only one PPS cup for mixing and spraying Enables painters
More informationBuild a. better betty. Improving. Tamiya s Imperial Japanese Navy bomber. 34 FineScale Modeler January 2008
Build a better betty Improving 34 FineScale Modeler January 2008 Tamiya s Imperial Japanese Navy bomber 1/ 48 Scale Aircraft How-to By Carmine Mari To World War II s Allies, the Mitsubishi G4M had an official
More informationslide decal and placed it on the chest of the robotic armor (Photo 5). After tamping the decal dry with a paper towel, I sprayed a light coat of
10 Sometimes unexpected surprises can fall right into your lap. That was the case when George Stephenson of BlackHeart Enterprises contacted Paul Gill of Gillman Productions to create a unique take on
More informationMarch 2009 Product Information RAPID GREYMATIC 2K Filler
GLOBAL REFINISH SYSTEM March 2009 Product Information RAPID GREYMATIC 2K Filler PRODUCT DESCRIPTION 2K RAPID GreyMatic is a range of 2K primer surfacers suitable for a wide range of repair work. Versatile,
More informationRoman Blind System SECTION J
System Roman Blind System SECTION J ROMAN BLIND SYSTEM EASY step by step fitting instructions Mono control operation - when the cord reaches its maximum drop, by continuing to pull on the chain the blind
More informationBuilding Instructions V 1.0 for a Styrene R0 Dome
Building Instructions V 1.0 for a Styrene R0 Dome Created by R2 Builders Sweden: Lars-Åke Siggelin, Lars Lindberg, Alexander Arvidsson & David Bergelv This building instruction is using 1mm and 3mm Polystyrene,
More informationSewing Instructions for Vest 9302 Sizes 34,36,38, 40,42. Length in Back: About 40 cm (about inches)
Sewing Instructions for Vest 9302 Sizes 34,36,38, 40,42 Length in Back: About 40 cm (about 15.74 inches) Fabric needed Glencheck, 150 cm (about 59 inches) wide, 0.60 meters (about 23.62 inches) long for
More informationhis is where you die, Sam... TThe veins bulged in Sam s head as he grit his teeth in pain. I am not ready to die. Sam pounded at the arm wrapped
01 sam his is where you die, Sam... TThe veins bulged in Sam s head as he grit his teeth in pain. I am not ready to die. Sam pounded at the arm wrapped tight around his neck but his enemy s grip was too
More information