ICF-F11S/F12S SERVICE MANUAL FM/SW/MW 3 BAND RADIO. E Model. Ver
|
|
- Damon Mills
- 5 years ago
- Views:
Transcription
1 SERVICE MANUAL E Model Ver Photo : ICF-F2S SPECIFICATIONS Frequency range: Band ICF-FS ICF-F2S MHz MHz MW khz khz SW MHz MHz Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Speaker Approx. 9.2 cm (3 5 / 8 inches) dia., 4 Ω Output v (earphone) jack (ø3.5mm minijack) Power output 300 mw (max) Power requirements 3V DC, two R20 (size D) batteries Dimensions Approx mm (w/h/d) (8 5 / 8 5 / / 4 inches) incl. projecting parts and controls Mass Approx. 676 g ( lb 8 oz) incl. carrying strap and batteries Supplied accessories carrying strap () Design and specifications are subject to change without notice. /SW/MW 3 BAND RADIO L Sony Corporation Audio Business Group Published by Sony Techno Create Corporation
2 SECTION SERVICING NOTES UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. A Rear Parte posterior SECTION 2 GENERAL R20 (size D) 2 R20 (tamaño D) 2 Telescopic antenna Antena telescópica This section is extracted from instruction manual. HOW TO CHANGED THE CERAMIC FILTERS This model is used two ceramic filters of CF and CF3. You must used same type of color marked ceramic filters in order to meet same specifications. Therefore, the ceramic filter must be changed two pieces together since it s supply two pieces in one package as a spare parts. mark CF3 CF Mark red blue orange black white Center frequency 0.70 MHz 0.67 MHz 0.73 MHz 0.64 MHz 0.76 MHz B Insert the E side of the battery first. Inserte primero el lado E de la pila. MW SW Installing the batteries (See fig. A) Open the battery compartment lid. 2 Install two R20 (size D) batteries (not supplied) with correct polarity. 3 Close the lid. Battery life (Approx. hours) (JEITA*) When using SW MW Sony R20 (size D) * Measured by JEITA (Japan Electronics and Information Technology Industries Association) Standards. The actual battery life may vary depending on the circumstance of the unit. When to replace the batteries When the sound becomes weak or distorted, replace all the batteries with new ones. Notes on batteries Do not charge the dry batteries. Do not carry the dry batteries with coins or other metallic objects. It can generate heat if the positive and negative terminals of the batteries are accidentally contacted by a metallic object. Do not use different types of batteries at the same time. When you replace the batteries, replace all with new ones. When you are not going to use the unit for a long time, remove the batteries to avoid damage from battery leakage and corrosion. Improving the reception (See fig. B) : Extend the telescopic antenna and adjust the angle for optimum reception. MW: Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built into the unit. SW: Extend the telescopic antenna vertically. Note Adjust the direction of the antenna by holding the bottom of it. The antenna can be damaged when you move the antenna with excessive force. 2
3 SECTION 3 DISASSEMBLY ICF-FS/F2S This set can be disassembled in the order shown below. 3-. DISASSEMBLY FLOW SET 3-5. GEAR (VC) AND MAIN BOARD SETTING (Page 5) 3-2. REAR CABINET BLOCK (Page 3) 3-3. MAIN BOARD, GEAR (VC) (Page 4) 3-4. TELESCOPIC ANTENNA (ANT), BATTERY CASE LID, CABINET (REAR) (Page 4) Note: Follow the disassembly procedure in the numerical order given REAR CABINET BLOCK screw rear cabinet block Open the battery case lid. screw three claws terminal board (antenna) antenna cable Remove a solder. 3
4 3-3. MAIN BOARD, GEAR (VC) two screws Remove a solder. gear (VC) Remove two solders. Remove a solder TELESCOPIC ANTENNA (ANT), BATTERY CASE LID, CABINET (REAR) telescopic antenna (ANT) cabinet (rear) battery case lid battery case lid two bosses cabinet (rear) cushion (battery) screw (M3 6) terminal board (antenna) 4
5 Note: Follow the assembly procedure in the numerical order given GEAR (VC) AND MAIN BOARD SETTING Match two gears. Down the pointer. first concave portion Set the second concave portion of pointer to the convex part of the gear (VC). rib of front cabinet Install the gear (VC) as shown in figure. pointer knob (tune) gear (VC) The vicinity of hole at center of gear (VC) and the pointer must be parallel. Note: Match the convex part of the gear (VC) to the second concave portion of pointer with pointer lowered most. two screws Rotate the shaft of CV in the direction of the arrow fully. Rotate the shaft of RV in the direction of the arrow fully. Rotate knob (VOL) in the direction of the arrow fully. 5
6 SECTION 4 ELECTRICAL ADJUSTMENT 0 db=0.280 mv [MW] Setting: BAND switch : MW AM RF signal generator 30% amplitude modulation by 400 Hz signal Output level: as low as possible Put the lead-wire antenna close to the set. set (SP ) 4 Ω (SP ) level meter MW/SW IF ADJUSTMENT Adjustment for a maximum reading on level meter T 455 khz MW FREQUENCY COVERAGE ADJUSTMENT Adjustment Part Frequency Display L5 520 khz CT khz MW TRACKING ADJUSTMENT Adjust for a maximum reading on level meter L 600 khz CT- 400 khz [SW] Setting: BAND switch: SW AM RF signal generator 0 pf 30% amplitude modulation by 400 Hz signal Output level: as low as possible [] Setting: BAND switch: RF signal generator 22.5 khz frequency deviation by 400 Hz signal Output level: as low as possible (ANT) set () 0.0 μf (ANT) set () (SP ) 4 Ω (SP ) level meter (SP ) 4 Ω (SP ) level meter no mark: FS ( ): F2S SW FREQUENCY COVERAGE ADJUSTMENT Adjustment Part Frequency Display L khz (5800 khz) CT khz (8250 khz) no mark: FS ( ): F2S SW TRACKING ADJUSTMENT Adjust for maximum reading on level meter L khz (5800 khz) CT2 (8250 khz) FREQUENCY COVERAGE ADJUSTMENT Adjustment Part Frequency Display L MHz CT MHz TRACKING ADJUSTMENT Adjust for a maximum reading on level meter L MHz CT MHz Adjustment Location: (See page 7) Repeat the procedures in each adjustment several times, and the tracking adjustments should be finally done by the trimmer capacitors. Remove antenna in adjustment. 6
7 Adjustment Location: MAIN BOARD (Component Side) SW Frequency Coverage Adjustment L6 CT3 T MW/SW IF Adjustment SW Tracking Adjustment L2 CT2 Tracking Adjustment L3 CT-3 S BAND SW MW Frequency Coverage Adjustment L4 CT-4 S2 POWER OFF ON MW Tracking Adjustment L CT- L5 CT-2 MW Frequency Coverage Adjustment MAIN BOARD (Conductor Side) () (ANT) (SP) (SP-) 7
8 MEMO 8
9 SECTION 5 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. Note: X : Parts extracted from the component side. W : indicates side identifi ed with part number. f : internal component. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) IC Block Diagram MAIN Board IC CXA09S AF OUT AF POWER AMP AM FE IF DISCRI VCC RIPPLE FILTER AF IN NF VOL AM OSC DET OUT AM IF DET AGC DISCRIMINATOR AFC AFC AGC OSC AFC AGC FE REG OUT IF RF METER TUNING METER AM RF IN N.C IF IN FE RF IN AM IF IN /AM BAND SELECT N.C /AM IF OUT For Schematic Diagrams. Note: All capacitors are in μf unless otherwise noted. (p: pf) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and /4 W or less unless otherwise specifi ed. f : internal component. C : panel designation. A : B Line. C : adjustment for repair. Power voltages is dc 3V and fed with regulated dc power supply from battery terminal. Voltages are dc with respect to ground in no-signal (defuned) conditions. no mark : ( ) : MW/SW Voltages are taken with a VOM (Input impedance 0 MΩ). Voltages variations may be noted due to normal production tolerances. Signal path. F : f : MW h : SW 5-. PRINTED WIRING BOARD - MAIN Board - : Uses unleaded solder. A B C D E F G H I J W3 DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 2PCS. 3V L MW FERRITE-ROD ANTENNA C9 C23 L4 OSC C6 C7 L3 RF CF JW4 CT-4 CT-3 30 C33 C3 CV-3 C4 C35 JC2 C32 CV-4 JC3 C36 CV TUNING W4 C22 CV- CV-2 C28 C27 C29 CT2 IC C26 C30 CT- CT-2 L2 SW RF C20 B Q C E SP C25 C34 L BRN BLK C C2 L5 MW OSC CT3 JW5 C24 C7 C2 C3 3 5 R3 SP BLK CF2 SP L6 SW OSC L8 CF3 6 RED R2 JW3 C8 C9 C0 C C4 C5 C6 R5 JC W2 BPF BAND PASS FILTER R JW2 RV VOLUME (SP) NATURAL JW () T AM IFT (ANT) (SP-) A/K D ICF-FS/F2S MAIN BOARD S2 POWER S BAND C37 ANT A K -4 R4 L7 MW C2 ON OFF SW ANT /SW TELESCOPIC ANTENNA () J ICF-FS/F2S 9 9
10 BAND SELECT N.C. METER AFC(W) AFC(J) AGC RIPPLE /AM DISCRI IF OUT N.C. C ICF-FS/F2S 5-2. SCHEMATIC DIAGRAM - MAIN Board - See page 9 for IC Block Diagram. CV S-2 C 6p C2 0p CT- TUNING MW FERRITE-ROD ANTENNA S-3 JC2 C35 C4 CT-3 L3 0 8p 0p CV-3 RF S-4 C8 220p C9 00p C0 47p C2 3p C3 22p CT-2 L5 MW OSC S-5 L8 2μH C 0p JC 0 JW5 C4 C7 3p C8 CT3 ANT /SW TELESCOPIC ANTENNA S BAND MW CV- C2 000p CT2 BPF BAND PASS FILTER L2 SW RF JW2 RV 50k VOLUME C6 p R 4.7k C7 22p CV-4 W2 L4 CV-2 CT-4 OSC *C4 000p 2200p C5 C6 470p *C5 470p 2200p *C8 p 0p L6 SW OSC (ANT) ANT D PS226 S- SW L7 μh C37 3p JW () C9 0 50V L μh C22 C V CF F.E RF IN AM RF RF REG OUT OSC AFC AM OSC VOL NF /MW/SW FRONT END, /MW/SW IF AMP, DET,AGC,AF AMP T AM IFT R2 2.2k IC CXA09S R3 220 AM IF IN IF IN C IF OUT DET OUT AF IN AF VCC OUT C36 C32 C V R4 47 (SP-) (SP) SP SP- SP J C27 W3 CF2 C25 C V 50V C30 C V 0V JW3 CF3 S-6 C C C33 W4 S2 POWER ON DRY BATTERY SIZE"D" (IEC DESIGNATION R20 2PCS.3V) 2PCS.3V Q 2SC454 HIGH CUT MUTING R5 00k JW4 OFF ICF-FS/F2S 0 0
11 Note: -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SECTION 6 EXPLODED VIEW The mechanical parts with no reference number in the exploded views are not supplied. Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE)... (RED) R R Parts of Color Cabinet s Color ICF-FS/F2S Accessories are given in the last of the electrical parts list. L 0 6 not supplied ANT not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SCREW (B3), () BV TAPPING CABINET (REAR) 3 X CABINET FRONT SUB ASSY (including SP) 3 X CABINET FRONT SUB ASSY (including SP) KNOB (VOL) KNOB (TUNE) TERMINAL ( ), BATTERY WASHER, POLY-SLIDER , BATTERY TERMINAL GEAR (VC) HOLDER (ANT) CUSHION (SW) 2 A A MAIN BOARD, COMPLETE 2 A A MAIN BOARD, COMPLETE CUSHION (BATTERY) LID, BATTERY CASE SCREW (M3X6 LOCK ACE) PIN (PVC) ANT ANTENNA, TELESCOPIC L BAR ANTENNA COIL (MW)
12 MAIN Note: Due to standardization, replacements in the parts list may be different from the parts specifi ed in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. CAPACITORS uf: μf SECTION 7 ELECTRICAL PARTS LIST COILS uh: μh RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-fi lm resistor. F: nonflammable SEMICONDUCTORS In each case, u: μ, for example: ua.. : μa.., upa.., μpa.., upb.. : μpb.., upc.., μpc.., upd.. : μpd.. When indicating parts by reference number, please include the board name. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A A A A MAIN BOARD, COMPLETE MAIN BOARD, COMPLETE ******************** PIN (PVC) HOLDER (ANT) CUSHION (SW) C CERAMIC CHIP 0.047uF 0% 6V C ELECT 22uF 20% 25V C ELECT 470uF 20% 0V C CERAMIC CHIP uf 0V C CERAMIC CHIP uf 0V C ELECT 470uF 20% 0V < BAND PASS FILTER > BPF FILTER, BAND PASS < CAPACITOR > C CERAMIC CHIP 6PF 0.5PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP PF 0.25PF 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 220PF 5% 50V C CERAMIC CHIP 00PF 5% 50V C CERAMIC CHIP 47PF 5% 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 0.00uF 0% 50V C CERAMIC CHIP uF 0% 50V C CERAMIC CHIP uF 0% 50V C CERAMIC CHIP 470PF 5% 50V C CERAMIC CHIP 470PF 5% 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP PF 0.25PF 50V C ELECT 0uF 20% 50V C CERAMIC CHIP 0.0uF 0% 25V C CERAMIC CHIP 0.00uF 0% 50V C CERAMIC CHIP 0.uF 25V C ELECT 4.7uF 20% 50V C CERAMIC CHIP 0.0uF 0% 25V C ELECT 4.7uF 20% 50V C ELECT 0uF 20% 50V C CERAMIC CHIP uf 0V C CERAMIC CHIP 0.022uF 0% 25V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP uf 0V C CERAMIC CHIP 3PF 0.25PF 50V < FILTER > CF FILTER, CERAMIC CF FILTER, CERAMIC CF FILTER, CERAMIC < VARIABLE CAPACITOR/TRIMMER > CT CAP, VAR CT CAP, CERAMIC TRIMMER CT CAP, CERAMIC TRIMMER < VARIABLE CAPACITOR > CV CAP, VAR (TUNING) < DIODE > D DIODE PS226-5 < IC > IC IC CXA09S < JACK > J JACK (v) < JUMPER RESISTOR > JC SHORT CHIP 0 JC SHORT CHIP 0 < COIL > L BAR ANTENNA COIL (MW) L COIL, SW (ANT) L HIGH FREQUENCY COIL L COIL, AIR-CORE L COIL, AIR-CORE L COIL, OSC (MW) L COIL, OSC (SW) L COIL, OSCILLATOR 2
13 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L INDUCTOR uh L INDUCTOR 2uH L INDUCTOR uh < TRANSISTOR > Q TRANSISTOR 2SC454-EF < RESISTOR > R METAL CHIP 4.7K 5% /0W R METAL CHIP 2.2K 5% /0W R METAL CHIP 220 5% /0W R METAL CHIP 47 5% /0W R METAL CHIP 00K 5% /0W < VARIABLE RESISTOR > RV RES, VAR, CARBON 50K (VOLUME) < SWITCH > S SWITCH, SLIDE (BAND) S SWITCH, SLIDE (POWER) < TRANSFORMER > T TRANSFORMER, IF ************************************************************ MISCELLANEOUS ************** 3 X CABINET FRONT SUB ASSY (including SP) 3 X CABINET FRONT SUB ASSY (including SP) ANT ANTENNA, TELESCOPIC ************************************************************* ACCESSORIES ************ MANUAL, INSTRUCTION (ENGLISH, SPANISH, PORTUGUESE, SIMPLIFIED CHINESE, ARABIC) BELT (SHOULDER) (Carrying strap) STOPPER, BELT (Buckle for strap) 3
14 MEMO 4
15 2. DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM. (In addition to this, the necessary note is printed in each block.) ICF-FS/F2S SERVICE MANUAL Ver SUPPLEMENT- File this supplement with the service manual. Subject: Change of (Suffix-2) E Model For Printed Wiring Boards. Note: X : Parts extracted from the component side. W : indicates side identifi ed with part number. f : internal component. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) For Schematic Diagrams. Note: All capacitors are in μf unless otherwise noted. (p: pf) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and /4 W or less unless otherwise specifi ed. f : internal component. C : panel designation. A : B Line. C : adjustment for repair. Power voltages is dc 3V and fed with regulated dc power supply from battery terminal. Voltages are dc with respect to ground in no-signal (defuned) conditions. no mark : ( ) : MW/SW Voltages are taken with a VOM (Input impedance 0 MΩ). Voltages variations may be noted due to normal production tolerances. Signal path. F : f : MW h : SW In this set, has been changed in the midway of production. Printed wiring boards, schematic diagrams and electrical parts list of new type are described in this supplement-. Refer to original service manual for other information.. NEW/FORMER DISCRIMINATION MAIN Board (Component Side) Former : New : ICF-FS/F2S
16 ICF-FS/F2S SCHEMATIC DIAGRAM - MAIN Board - SP R4 C34 C32 C36 C33 C30 C3 C29 C28 C27 C25 C26 R5 R3 C24 R2 JW3 JW4 L7 C37 JW C2 L JW2 C9 R C22 C23 CF W2 C8 C3 C8 C9 C0 C C4 C5 C7 L8 JW5 CT2 JC2 C2 IC ANT C C4 C6 C2 C6 C7 C35 JC CT3 RV CF2 CF3 W3 W4 Q S2 J D CT- L2 S-6 S-2 S-3 L3 CV-3 CV-4 CT-4 L4 CV-2 CV- BPF CT-3 S- S-5 CT-2 L5 L6 T ANT S-4 C V 22 25V 470 0V V 0 50V 00k k 3p 000p 0 50V 4.7k V 22p 220p 00p 47p 0p 22p 0 0p CXA09S 6p 0p p 3p 470p 3p 8p 0 50k 2SC454 PS226 (SP-) (SP) () (ANT) 0.0 OUT VCC RIPPLE IN OUT AGC METER N.C. SELECT AF AF DET AFC(J) AFC(W) AM BAND OUT IF DISCRI NF VOL AM AFC REG AM OSC OSC OUT RF RF N.C. F.E /AM IF IN IF IN IN RF IF OUT DET,AGC,AF AMP ANTENNA TELESCOPIC *C4 000p 2200p 2200p 470p *C5 p 0p *C8 ANTENNA FERRITE-ROD MW VOLUME /SW /MW/SW FRONT END, /MW/SW IF AMP, SP SP- MW OSC SW OSC RF OSC SW RF OFF ON POWER SW MW BAND S TUNING CV DRY BATTERY SIZE"D" (IEC DESIGNATION R20 2PCS.3V) 2PCS.3V HIGH CUT MUTING BAND PASS FILTER AM IFT μh μh 2μH
17 2-2. PRINTED WIRING BOARD - MAIN Board - : Uses unleaded solder A MAIN BOARD L MW FERRITE-ROD ANTENNA B S2 POWER ON C L4 OSC BLK OFF C6 C7 CT-4 CV TUNING CV-4 CV- CT- C C2 RED D C2 C3 C8 C9 C0 C S BAND CT-3 L5 MW OSC W2 E F G H I C9 W3 DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 2PCS. 3V C23 L3 RF CF JW4 30 C33 C3 CV-3 C4 C35 JC2 C32 JC3 C36 W4 C22 CV-2 C28 C27 C29 CT2 IC C26 C30 CT-2 L2 SW RF C20 C25 B Q C E L CT3 JW5 C24 C7 3 5 R3 CF2 L6 SW OSC L8 CF3 6 R2 JW3 C4 C5 C6 R5 JC BPF BAND PASS FILTER R JW2 RV VOLUME NATURAL JW () T AM IFT (ANT) A/K -5-4 MW -3-2 SW -6 - L7 C37 ANT A D K C2 ANT /SW TELESCOPIC ANTENNA J C34 R4 SP SP SP (SP) (SP-) (2) J BRN BLK 3
18 MAIN 3. ELECTRICAL PARTS LIST Note: Due to standardization, replacements in the parts list may be different from the parts specifi ed in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. CAPACITORS uf: μf COILS uh: μh RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-fi lm resistor. F: nonflammable SEMICONDUCTORS In each case, u: μ, for example: ua.. : μa.., upa.., μpa.., upb.. : μpb.., upc.., μpc.., upd.. : μpd.. When indicating parts by reference number, please include the board name. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A A A A MAIN BOARD, COMPLETE MAIN BOARD, COMPLETE ******************** PIN (PVC) HOLDER (ANT) CUSHION (SW) C CERAMIC CHIP 0.047uF 0% 6V C ELECT 22uF 20% 25V C ELECT 470uF 20% 0V C CERAMIC CHIP uf 0V C CERAMIC CHIP uf 0V C ELECT 470uF 20% 0V < BAND PASS FILTER > BPF FILTER, BAND PASS < CAPACITOR > C CERAMIC CHIP 6PF 0.5PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP PF 0.25PF 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 220PF 5% 50V C CERAMIC CHIP 00PF 5% 50V C CERAMIC CHIP 47PF 5% 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 0.00uF 0% 50V C CERAMIC CHIP uF 0% 50V C CERAMIC CHIP uF 0% 50V C CERAMIC CHIP 470PF 5% 50V C CERAMIC CHIP 470PF 5% 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 0PF 0.5PF 50V C CERAMIC CHIP PF 0.25PF 50V C ELECT 0uF 20% 50V C CERAMIC CHIP 0.0uF 0% 25V C CERAMIC CHIP 0.00uF 0% 50V C CERAMIC CHIP 0.uF 25V C ELECT 4.7uF 20% 50V C CERAMIC CHIP 0.0uF 0% 25V C ELECT 4.7uF 20% 50V C ELECT 0uF 20% 50V C CERAMIC CHIP uf 0V C CERAMIC CHIP 0.022uF 0% 25V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP uf 0V C CERAMIC CHIP 3PF 0.25PF 50V < FILTER > CF FILTER, CERAMIC CF FILTER, CERAMIC CF FILTER, CERAMIC < VARIABLE CAPACITOR/TRIMMER > CT CAP, VAR CT CAP, CERAMIC TRIMMER CT CAP, CERAMIC TRIMMER < VARIABLE CAPACITOR > CV CAP, VAR (TUNING) < DIODE > D DIODE PS226-5 < IC > IC IC CXA09S < JACK > J JACK (v) < JUMPER RESISTOR > JC SHORT CHIP 0 JC SHORT CHIP 0 < COIL > L BAR ANTENNA COIL (MW) L COIL, SW (ANT) L HIGH FREQUENCY COIL L COIL, AIR-CORE L COIL, AIR-CORE L COIL, OSC (MW) L COIL, OSC (SW) L COIL, OSCILLATOR 4
19 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L INDUCTOR uh L INDUCTOR 2uH L INDUCTOR uh < TRANSISTOR > Q TRANSISTOR 2SC454-EF < RESISTOR > R METAL CHIP 4.7K 5% /0W R METAL CHIP 2.2K 5% /0W R METAL CHIP 220 5% /0W R METAL CHIP 47 5% /0W R METAL CHIP 00K 5% /0W < VARIABLE RESISTOR > RV RES, VAR, CARBON 50K (VOLUME) < SWITCH > S SWITCH, SLIDE (BAND) S SWITCH, SLIDE (POWER) < TRANSFORMER > T TRANSFORMER, IF 5
20 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision New Change of (Suffix-2) (SUPPLEMENT-) (ECN-ECC57576)
ICF-C112 SERVICE MANUAL FM/AM CLOCK RADIO. E Model. Ver Sony Corporation SPECIFICATIONS
SERVICE MANUAL E Model Ver 1.0 2003. 03 SPECIFICATIONS Time display: 12-hour system Frequency range: : 87.5-108 MHz AM: 530-1710 khz Speaker: Approx. 6.6 cm (2 5/8 inches) dia., 8 ohm Power output: 120
More informationSRF-PSY03 SERVICE MANUAL FM STEREO/AM RADIO. US Model SPECIFICATIONS. Photo: Violet model MICROFILM
SRF-PSY03 SERVICE MANUAL US Model Photo: Violet model SPECIFICATIONS STEREO/ RADIO MICROFILM TABLE OF CONTENTS 1. GENERAL... 3. DISASSEMBLY... 4 Notes on chip component replacement Never reuse a disconnected
More informationECM-S80 SERVICE MANUAL ELECTRET CONDENSER MICROPHONE. US Model Canadian Model AEP Model E Model. Ver
SERVICE MANUAL Ver.0 00. 0 US Model Canadian Model AEP Model E Model SPECIFICATIONS Type Electret condenser microphone Cord ø. mm ( 3 / 3 in.)ofc litz cord ( core shielded) Length:Approx.70 cm (7 5 / 8
More informationSPECIFICATIONS. Power output 3.6mW + 3.6mW (at 10% harmonic distortion) Power requirements 1.5 V DC, one R03 (rize AAA)
SERVICE MANUAL Ver. 004.05 E Model Australian Model Chinese Model Tourist Model SPECIFICATIONS Frequency range : 87.5-08 MHz (EXCEPT Tourist model) : 76-08 MHz (Tourist model) : 530-605kHz Output (stereo
More informationICF-704S SERVICE MANUAL FM/SW/MW 3 BAND RADIO. Australian Model. Ver
SERVICE MANUAL Australian Model Ver.0 2004. 04 SPECIFICATIONS Frequency range: Band FM SW MW ICF-704S 87.5-08.0 MHz 5.95-8 MHz 530-605 khz Speaker: Approx. 0.2 cm (4 /8 inches) dia. 8 ohms Power output:
More informationPhoto: SRS-Z750PC SPECIFICATIONS. Stereo mini jack (INPUT) (SRS-Z750) Stereo mini jack 2 (INPUT 1, 2) (SRS-Z750PC)
SRS-Z750/Z750PC SERVICE MANUAL Ver 1.0 1998. 07 US Model Canadian Model AEP Model UK Model E Model Australian Model Left speaker Right speaker Photo: SRS-Z750PC SPECIFICATIONS Amplifier section Power output
More informationXM-502X. SERVICE MANUAL Ver STEREO POWER AMPLIFIER. US Model Canadian Model AEP Model UK Model E Model. Sony Corporation SPECIFICATIONS
XM-502X SERVICE MANUAL Ver 1.1 2001. 08 US Model Canadian Model AEP Model UK Model E Model SPECIFICATIONS Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High
More informationCFS-717S SERVICE MANUAL RADIO CASSETTE-CORDER. E Model. Ver SPECIFICATIONS
CFS-717S SERVICE MANUAL Ver 1.1 1999. 11 E Model Model Name Using Similar Mechanism Tape Transport Mechanism Type CFS-W475 MF-W475 SPECIFICATIONS RADIO CASSETTE-CORDER MICROFILM Ver 1.1 1999. 11 MODEL
More informationIllustration : MDR-IF330R SPECIFICATIONS
MDR-IF230/IF330R SERVICE MANUAL Ver 1.1 2000. 06 US Model Canadian Model E Model Australian Model MDR-IF230/IF330R Tourist Model MDR-IF330R Illustration : MDR-IF330R MDR-IF230 is the component model block
More informationSRF-M75PM SERVICE MANUAL FM STEREO/AM PLL SYNTHESIZED RADIO. US Model Canadian Model AEP Model E Model Australian Model. Ver
SRF-M75PM SERVICE MANUAL Ver 1.0 1999. 04 US Model Canadian Model AEP Model E Model Australian Model SPECIFICATIONS US, Canadian, and E models AEP, Australian models FM STEREO/AM PLL SYNTHESIZED RADIO
More informationSRF-T615 SERVICE MANUAL FM STEREO/AM PLL SYNTHESIZED RADIO. Tourist Model. Ver SPECIFICATIONS MICROFILM
SRF-T615 SERVICE MANUAL Ver 1.0 1999.10 Tourist Model SPECIFICATIONS FM STEREO/AM PLL SYNTHESIZED RADIO MICROFILM TABLE OF CONTENTS Specifications... 1 1. GENERAL Location and Function of Controls... 2
More informationSTEREO POWER AMPLIFIER. AEP Model UK Model
XM-5020X SERVICE MANUAL AEP Model UK Model This set has almost the same specifications as the XM-502X. This service manual only describes the differences from the XM-502X. Refer to the appropriate service
More informationSUPPLEMENT-1. File this supplement with the service manual. Subject : 1. Change of Illumination Color 2. Change of Main and Display Boards
MDX-C6500X SERVICE MANUAL US Model Canadian Model E Model SUPPLEMENT-1 File this supplement with the service manual. Subject : 1. Change of Illumination Color 2. Change of Main and Display Boards (ECN-CSA02152,
More informationSRF-M55 SERVICE MANUAL FM STEREO PLL SYNTHESIZED RADIO. AEP Model E Model Chinese Model. Ver SPECIFICATIONS MICROFILM
SRF-M SERVICE MANUAL Ver.0 999.09 AEP Model E Model Chinese Model SPECIFICATIONS FM STEREO PLL SYNTHESIZED RADIO MICROFILM TABLE OF CONTENTS Specifications.... GENERAL Location and Function of Controls...
More informationSRF-M75PM SERVICE MANUAL FM STEREO/AM PLL SYNTHESIZED RADIO. US Model Canadian Model AEP Model E Model Australian Model. Ver
SRF-M75PM SERVICE MANUAL Ver 1.0 1999. 04 US Model Canadian Model AEP Model E Model Australian Model SPECIFICATIONS US, Canadian, and E models AEP, Australian models FM STEREO/AM PLL SYNTHESIZED RADIO
More informationCFD-S23 SERVICE MANUAL Ver 1.0 1998. 08 SUPPLEMENT - 1 File this Supplement with the Service Manual. Subject : r EAST EUROPEAN AND RUSSIAN MODEL HAS BEEN ADDED r CHANGE OF BOARDS AC INLET BOARD : 1-666-267-11
More informationPhoto : WM-FX195 SPECIFICATIONS
WM-FX193/FX195 SERVICE MANUAL Ver 1.0 2000.01 US Model WM-FX193 Canadian Model AEP Model E Model Chinese Model WM-FX193/FX195 Photo : WM-FX195 Model Name Using Similar Mechanism Tape Transport Mechanism
More informationICF-C793/C793L SERVICE MANUAL FM/AM PLL SYNTHESIZED CLOCK RADIO FM/MW/LW PLL SYNTHESIZED CLOCK RADIO. US Model Canadian Model Australian Model
ICF-C793/C793L SERVICE MANUAL Ver 1.0 1999. 02 US Model Canadian Model Australian Model ICF-C793 AEP Model ICF-C793/C793L UK Model ICF-C793L Photo: ICF-C793L SPECIFICATIONS ICF-C793 FM/AM PLL SYNTHESIZED
More informationSPP-ID970/ID971 SERVICE MANUAL CORDLESS TELEPHONE. US Model SPP-ID970 Canadian Model SPP-ID971
SPP-ID970/ID971 SERVICE MANUAL Ver 1.3 2000. 12 With SUPPLEMENT-1 (9-927-617-81) With SUPPLEMENT-2 (9-927-617-82) US Model SPP-ID970 Canadian Model SPP-ID971 Photo: SPP-ID970 SPECIFICATIONS General Frequency
More informationSPECIFICATIONS. AUDIO POWER SPECIFICATIONS (US model)
SRVIC MANUAL Ver.. 2008.02 US Model AP Model UK Model Wood color type is the subwoofer in HT-DDW890/ DDWG800. Black color type is the subwoofer in HT-7200DH. SPCIFICATIONS AUDIO POWR SPCIFICATIONS (US
More informationTA-E1 SERVICE MANUAL STEREO PRE AMPLIFIER. US Model Canadian Model AEP Model UK Model E Model Australian Model SPECIFICATIONS MICROFILM
TA-E1 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Australian Model SPECIFICATIONS STEREO PRE AMPLIFIER MICROFILM 1 SAFETY CHECK-OUT After correcting the original service problem,
More informationXM-2252HX SERVICE MANUAL STEREO POWER AMPLIFIER. US Model Canadian Model AEP Model UK Model SPECIFICATIONS MICROFILM
XM-2252HX SERVICE MANUAL US Model Canadian Model AEP Model UK Model SPECIFICATIS STEREO POWER AMPLIFIER MICROFILM TABLE OF CTENTS Specifications.... SERVICING NOTE... 2 2. GENERAL... 3 3. ELECTRICAL ADJUSTMENTS
More informationICF-SC1/SC1PC SERVICE MANUAL PLL SYNTHESIZED SCANNING RECEIVER. US Model. Ver SPECIFICATIONS
ICF-SC1/SC1PC SERVICE MANUAL Ver 1.0 1998.03 US Model SPECIFICATIONS Circuit system : Triple conversion superheterodyne Frequency range : 25.000 1300.000MHz (excluding cellular phone band : 823.980 849.020
More informationICF-C763/C763L SERVICE MANUAL FM/AM PLL SYNTHESIZED CLOCK RADIO FM/MW/LM PLL SYNTHESIZED CLOCK RADIO. US Model Canadian Model ICF-763 ICF-763L
SERVICE MANUAL Ver.0 2004.05 US Model Canadian Model ICF-C763 AEP Model ICF-C763/C763L UK Model ICF-C763L SPECIFICATIONS Time display UK, North and South America Other countries/regions 2-hour system 24-hour
More informationWM-FX463/FX465. SERVICE MANUAL Ver With SUPPLEMENT-2 ( ) RADIO CASSETTE PLAYER. US Model Canadian Model AEP Model E Model
WM-FX463/FX465 SERVICE MANUAL Ver 1.1 1999. 12 With SUPPLEMENT-2 (9-923-190-82) US Model Canadian Model AEP Model E Model Photo: FX465 Model Name Using Similar Mechanism Tape Transport Mechanism Type NEW
More informationAM RADIO KIT MODEL AM-780K. Assembly and Instruction Manual
AM RADIO KIT MODEL AM-780K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2007, 1999 by Elenco Electronics, Inc. All rights reserved. Revised 2007 REV-F 753108 No part of this book
More informationCXA1691AM/AS. FM/AM Radio. Description CXA1691AM/AS is a one-chip FM/AM radio IC designed for radio-cassette tape recorders.
/ Radio CXA69/AS Description CXA69/AS is a one-chip / radio IC designed for radio-cassette tape recorders. CXA69 CXA69AS 28 pin SOP (Plastic) 30 pin SDIP (Plastic) Features Small number of peripheral components.
More informationRadiØKit Μ CW HAM RADIO TRANSCEIVER KIT. Assembly and operating manual
RadiØKit-120 20Μ CW HAM RADIO TRANSCEIVER KIT Assembly and operating manual Boreiou Ipirou 78 Kolonos Athens- Greece - 10444 Tel: 210.5150527 210.5132673 www.freebytes.com Thank you for buying RadiØKit-1,
More informationAM RADIO KIT MODEL AM-780K. Assembly and Instruction Manual ELENCO
AM-780K_REV-K_050416.qxp_AM-780K_REV-K_050416 5/10/16 8:13 AM Page 1 AM RADIO KIT MODEL AM-780K Assembly and Instruction Manual ELENCO Copyright 2016, 1999 by Elenco Electronics, Inc. All rights reserved.
More informationTA-N1 SERVICE MANUAL STEREO POWER AMPLIFIER. US Model Canadian Model AEP Model UK Model E Model Australian Model SPECIFICATIONS MICROFILM
TA-N1 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Australian Model SPECIFICATIONS STEREO POWER AMPLIFIER MICROFILM 1 SAFETY CHECK-OUT After correcting the original service problem,
More informationDT-120 FM STEREO/AM/TV RADIO CONTENTS
DT-120 FM STEREO/AM/TV RADIO CONTENTS Specification 2-3 Block Diagram 4 Alignment Instructions 5-8 Test Points Diagram.. 9 PCB Top View.. 10 PCB Bottom View........11 Wiring Diagram.........12 Troubleshooting
More informationAM/FM RADIO KIT MODEL AM/FM-108CK SUPERHET RADIO CONTAINS TWO SEPARATE AUDIO SYSTEMS: IC AND TRANSISTOR. Assembly and Instruction Manual ELENCO
AM/FM RADIO KIT MODEL AM/FM-108CK SUPERHET RADIO CONTAINS TWO SEPARATE AUDIO SYSTEMS: IC AND TRANSISTOR Assembly and Instruction Manual ELENCO Copyright 2012 by ELENCO All rights reserved. 753510 No part
More informationICF-703/703L SERVICE MANUAL FM/AM RADIO. AEP Model. UK Model ICF-703L ICF-703 FM/MW/LW 3 BAND RADIO ICF-703L. Ver
IF-703/703L SERVIE MANUAL Ver 1.0 2000. 03 AEP Model IF-703/703L UK Model IF-703L (Photo: IF-703L (BLAK)) SPEIFIATIONS Frequency range: Italy Band IF-703 IF-703L FM 87.5-108.0 MHz AM 526.5-1606.5 khz Other
More informationAM/FM RADIO KIT MODEL AM/FM-108K INTEGRAL CIRCUIT, 9 TRANSISTORS, 4 DIODES. Assembly and Instruction Manual
AM/FM RADIO KIT MODEL AM/FM-108K INTEGRAL CIRCUIT, 9 TRANSISTORS, 4 DIODES Assembly and Instruction Manual TM Elenco Electronics, Inc. Copyright 2003, 1989 by Elenco TM Electronics, Inc. All rights reserved.
More informationAM/FM RADIO KIT MODEL AM/FM-108K INTEGRAL CIRCUIT, 9 TRANSISTORS, 4 DIODES. Assembly and Instruction Manual
AM/FM RADIO KIT MODEL AM/FM-108K INTEGRAL CIRCUIT, 9 TRANSISTORS, 4 DIODES Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2009, 1989 by Elenco Electronics, Inc. All rights reserved.
More informationStep by Step Building PJ meter ARDF Receiver Kit. CRKITS.COM August 5, 2013
Step by Step Building PJ-80 80-meter ARDF Receiver Kit CRKITS.COM August 5, 2013 What is ARDF? ARDF is the abbreviation of Amateur Radio Direction Finding, or so called Fox Hunting. If you are looking
More informationCXA1619BM/BS. FM/AM Radio
/ Radio CXA69BM/BS Description CXA69BM/BS is a one-chip / radio IC designed for radio-cassette tape recorders and headphone tape recorders, and has the following functions. CXA69BM CXA69BS 28 pin SOP (Plastic)
More informationAUTO-SCAN FM RADIO KIT
FM-88K 071210.qxp_FM-88K 060810 12/29/15 10:05 AM Page 1 AUTO-SCAN FM RADIO KIT MODEL FM-88K Assembly and Instruction Manual ELENCO Copyright 2016, 2011 by ELENCO All rights reserved. No part of this book
More informationLINEAR INTEGRATED CIRCUIT
/ Radio DESCRIPTION The UTC CXA1191 is a one-chip / radio IC designed for radio-cassette tape recorders and headphone tape recorders. SOP-28 FEATURES *Small number of peripheral components *Low current
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More information12kHz LIF Converter V2.43 9Mhz version
12kHz LIF Converter V2.43 9Mhz version Please Note: This document supersedes all previously released documents and drawings on the LIF subject. This is the latest and most up-to-date document at this time.
More informationSTEREO CASSETTE DECK. AEP Model UK Model E Model Tourist Model SPECIFICATIONS
TC-TX101 SERVICE MANUAL AEP Model UK Model E Model Tourist Model This set is the optional stereo cassette deck that can be used only with section HCD-101 (AEP, UK model) / CMT-101 (E, Tourist model). Dolby
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Assembly and Instruction Manual Elenco
More informationAUTO-SCAN FM RADIO KIT
AUTO-SCAN FM RADIO KIT MODEL FM-88K ELENCO 150 Carpenter Avenue Wheeling, IL 0090 (8) 51-800 Website: www.elenco.com e-mail: elenco@elenco.com To see our complete line of Educational Products go to WWW.ELENCO.COM
More informationModel SR554 Transformer Preamplifier
Model SR554 Transformer Preamplifier Model SR554 Transformer Preamplifier 1290-D Reamwood Avenue Sunnyvale, California 94089 Phone: (408) 744-9040 Fax: (408) 744-9049 email: info@thinksrs.com www.thinksrs.com
More informationASSEMBLY MANUAL FOR R3500D DIRECTION FINDING RECEIVER KIT
SDR-Kits www.sdr-kits.net SDR-Kits is CRKITS Authorised Distributor for Europe ASSEMBLY MANUAL FOR R3500D DIRECTION FINDING RECEIVER KIT Rev. A May 24, 2015 Written by CRKITS http://www.crkits.com Thanks
More informationINTEGRATED CIRCUITS DATA SHEET. TEA5591 AM/FM radio receiver circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 June 1989 GENERAL DESCRIPTION The is an integrated radio circuit which is designed for use in portable receivers and clock radios. The
More information(without price) CTK-50 CTK-50 ELECTRIONIC KEYBOARD
(without price) CTK-0 CTK-0 ELECTRIONIC KEYBOARD CONTENTS Specification... 2 Block Diagram... 3 Circuit Description... 4 Troubleshooting... 7 Major Waveforms... 8 Schematic Diagrams... 9 PCB View... 11
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationHAMTRONICS R901 FM RECEIVER INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS
HAMTRONICS R901 FM RECEIVER INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS GENERAL INFORMATION. The R901 is a commercial grade single-channel fm receiver for the 902-928 MHz amateur band and the
More informationHAMTRONICS TB901 FM EXCITER INSTALLATION, OPERATION, & MAINTENANCE
HAMTRONICS TB901 FM EXCITER INSTALLATION, OPERATION, & MAINTENANCE GENERAL INFORMATION. The TB901 is a single-channel low power fm transmitter (exciter) designed to provide 300-600 milliwatts continuous
More informationUNISONIC TECHNOLOGIES CO., LTD
FM/AM Radio UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION The UTC CXA1191 is a one-chip FM/AM radio IC designed for radio-cassette tape recorders and headphone tape recorders. FEATURES *Small number of peripheral
More informationTHE 1956 ZENITH ROYAL 500 TRANSISTOR OWL S EYES RADIO.
THE 1956 ZENITH ROYAL 500 TRANSISTOR OWL S EYES RADIO. Dr. H. Holden. Feb. 2018. Introduction: The Zenith Royal 500 radio appeared in 1956, two years later than the Regency TR1 which was the first commercial
More informationSoftRock v6.0 Builder s Notes. May 22, 2006
SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationSoftRock v6.0 Builder s Notes. April 6, 2006
SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),
More informationHCD-DX50/RG80 SERVICE MANUAL MINI HI-FI COMPONENT SYSTEM. Canadian Model. Australian Model E Model. Ver
SERVICE MANUAL Ver 1.3 2003. 10 Canadian Model HCD-RG80 Australian Model E Model HCD-DX50 HCD-DX50/RG80 are the tuner, deck, CD and amplifier section in MHC-DX50/RG80. Photo : HCD-DX50 Model Name Using
More informationHT-1A Dual Band CW QRP Transceiver. Kit Building Instructions
HT-A Dual Band CW QRP Transceiver Kit Building Instructions Rev B, July 8, 08 Designed by BD4RG Exclusively distributed by CRKITS.COM and its worldwide distributors Join the group http://groups.io/g/crkits
More informationThe Walford Electronics Ford Receiver Kit Project Construction Manual
The Walford Electronics Ford Receiver Kit Project Construction Manual Walford Electronics Ford Receiver construction manual V1.5 Page 1 of 22 Introduction The Ford receiver has four stages: The first stage
More informationZN414Z, ZN415E, ZN416E AM RADIO RECEIVERS
GEC PLESSEY [SEMICONDUCTORS ZN414Z, ZN415E, ZN416E AM RADIO RECEIVERS FEATURES Single cell operation (1.1 to 1.6 volt, operating range) Low current consumption 150kHz to 3MHz frequency range (i.e. full
More informationSERVICE MANUAL ADDENDUM
Mar. 2010 SERVICE MANUAL ADDENDUM CONTENTS PARTS LIST................................ 1 BOARD LAYOUTS........................... 5 VOLTAGE DIAGRAM......................... 7 Feb. 2010 SERVICE MANUAL ADDENDUM
More informationAssembly Instructions for the FRB FET FM 70 Watt Amp
Assembly Instructions for the FRB FET FM 70 Watt Amp 1.) Orient the circuit board with the diagram 2.) Use a narrow chisel tip 25-30 watt soldering iron for assembly 3.) All the small parts are taped onto
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationThe Uniden Grant XL Owners Site
The Uniden Grant XL Owners Site Modifications page for the Grant XL (For Informational purposes only) The author of this site takes NO responsibility for illegal modifications and/or use of illegally modified
More informationWiring Manual NEScaf April 2010 (August 2006)
Wiring Manual NEScaf April 2010 (August 2006) Switched Capacitor Audio Filter The NEScaf is a switched capacitor audio filter (acronym SCAF) built around a building-block type filter chip. The NEScaf will
More informationTELEPHONE BUG KIT MODEL K-35. Assembly and Instruction Manual
TELEPHONE BUG KIT MODEL K-35 Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2010, 1989 by Elenco Electronics, Inc. All rights reserved. Revised 2010 REV-L 753235 No part of this book
More informationITT Technical Institute. ET275 Electronic Communications Systems I Onsite Course SYLLABUS
ITT Technical Institute ET275 Electronic Communications Systems I Onsite Course SYLLABUS Credit hours: 4 Contact/Instructional hours: 50 (30 Theory Hours, 20 Lab Hours) Prerequisite(s) and/or Corequisite(s):
More informationET275P Electronic Communications Systems I [Onsite]
ET275P Electronic Communications Systems I [Onsite] Course Description: In this course, several methods of signal transmission and reception are covered, including such techniques as mixing, modulating
More informationThe 6LE8 One Tube Broadcaster
The 6LE8 One Tube Broadcaster Introduction The purpose of this broadcaster is to transmit your favorite music to every AM radio in your home. The transmitting power is so low that it should not bother
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationECE 404 e-notes...copyright 2008 by Gregory M. Wierzba. All rights reserved...fall 2008.
ECE 404L: RF ELECTRONICS LABORATORY DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lab III - AM/FM Radio - AM Radio II. PURPOSE: This lab will focus on soldering
More informationKN-Q10 Assembly Manual
KN-Q10 Assembly Manual Translated by Adam Rong, BD6CR/4 with permission from Ke Shi, BA6BF Edited by Stephen, VK2RH Revision B, Oct 14, 2010 Thank you for purchasing the KN-Q10 4 Band SSB/CW Dual Mode
More informationTDA7000 for narrowband FM reception
TDA7 for narrowband FM reception Author: Author: W.V. Dooremolen INTRODUCTION Today s cordless telephone sets make use of duplex communication with carrier frequencies of about.7mhz and 49MHz. In the base
More information1 REF PART NO DESCRIPTION REMARKS QTY
Page 1 REF PART NO DESCRIPTION REMARKS QTY 100 1033987 HOUSING ASSY., LOWER 1 102 1033832 COVER, SEALED, REAR 1 103 1033988 HOUSING ASSY., UPPER 1 104 B310204411 C.B.B. SCREW M3X10 12 105 1033813 CAP,
More informationHF Amateur SSB Receiver
HF Amateur SSB Receiver PCB Set for radio club project http://rhelectronics.net PCB for DIY HF Amateur SSB Receiver 20M The receiver is a simple syperheterodyne type with quartz crystal filter. The circuit
More informationOperation Manual. Model SG Elenco Precision Wide Band Signal Generator
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Elenco Precision Wide Band Signal Generator Model SG-9000 Operation Manual CONTENTS
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationLab Equipment EECS 311 Fall 2009
Lab Equipment EECS 311 Fall 2009 Contents Lab Equipment Overview pg. 1 Lab Components.. pg. 4 Probe Compensation... pg. 8 Finite Instrumentation Impedance. pg.10 Simulation Tools..... pg. 10 1 - Laboratory
More informationS Pixie QRP Kit User Manual. Welcome to visit the home page to obtain the latest data. 1 / 24. Revision V160515
S-Pixie QRP Kit User Manual Revision V160515 Welcome to visit the home page www.lxqqfy.com to obtain the latest data. 1 / 24 1. Introduction PIXIE is a very small volume of simple 40 meter band micro-power
More informationAM radio / FM IF stereo system IC
AM radio / FM IF stereo system IC The is an AM radio and FM IF stereo system IC developed for radio cassette players. The FM circuit is comprised of a differential IF amplifier, a double-balance type quadrature
More informationWIRELESS MICROPHONE. Audio in the ISM band
WIRELESS MICROPHONE udio in the ISM band Ton Giesberts When the ISM frequency band was made available in Europe for audio applications, Circuit Design, a manufacturer of professional RF modules, decided
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM138/LM338 5-Amp Adjustable Regulators General Description The LM138 series
More informationTS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationMANUAL UPDATING CHANGES CHANGE DATE: June 16, 2004
MANUAL UPDATING CHANGES CHANGE DATE: June 16, 2004 MANUAL IDENTIFICATION MANUAL UPDATING COVERAGE This supplement adapts your manual to Serial Numbers prefixed through: 3708A Instrument: HP 5087A Distribution
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationINTEGRATED CIRCUITS DATA SHEET. TDA7021T FM radio circuit for MTS. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The integrated radio receiver circuit is for portable radios, stereo as well as mono, where a minimum of
More informationYAP BOX KIT MODEL K-22A YAP BOX SIX EXCITING SOUNDS. Assembly and Instruction Manual
YAP BOX KIT MODEL K-22A YAP BOX SIX EXCITING SOUNDS Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2009, 1989 by Elenco Electronics, Inc. All rights reserved. Revised 2009 REV-H 753222
More information10 2 2,13,15,16,46 27, non-inductive ,26,
HANDS-ON RADIO PARTS LIST (Thanks, John AF4WM and Steve AD7KR) Updated through Experiment 129 Quantities assume all parts available for re-use MAX QTY EXPERIMENT NOTES 1/4 WATT RESISTOR (All values are
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationTen Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
More informationFM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Build Instructions Before you start, take
More informationDIGITAL MULTIMETER KIT
DIGITAL MULTIMETER KIT MODEL M-1008K Assembly and Instruction Manual ELENCO Copyright 2012 by ELENCO All rights reserved. 753014 No part of this book shall be reproduced by any means; electronic, photocopying,
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1988 Elenco Electronics, Inc. Revised 2002 REV-K 753110 DT-100 PARTS LIST If you are a student,
More informationFMR622S DUAL NARROW BAND SLIDING DE-EMPHASIS DEMODULATOR INSTRUCTION BOOK IB
FMR622S DUAL NARROW BAND SLIDING DE-EMPHASIS DEMODULATOR INSTRUCTION BOOK IB 1222-22 TABLE OF CONTENTS SECTION 1.0 INTRODUCTION 2.0 INSTALLATION & OPERATING INSTRUCTIONS 3.0 SPECIFICATIONS 4.0 FUNCTIONAL
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions contact qrpkits.com@gmail.com There is no need to print out the whole assembly
More informationV6.2 SoftRock Lite Builder s Notes. November 17, 2006
V6.2 SoftRock Lite Builder s Notes November 17, 2006 Be sure to use a grounded tip soldering iron in building the v6.2 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch
More informationLM150/LM350A/LM350 3-Amp Adjustable Regulators
LM150/LM350A/LM350 3-Amp Adjustable Regulators General Description The LM150 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 3A over a 1.2V to 33V output
More information