MODEL GHA300F-12 GHA300F-24 GHA300F-48 VOLTAGE[V] AC f (output derating is required at AC90V -115V *3) CURRENT[A]

Transcription

1 AC-DC Power Supplies Medical Type GHA300F Ordering information GH A 300 F -OO -O R Example recommended EMI/EMC filter EAC-0-47 High voltage pulse noise type : EAP series Low leakage current type : EAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. Series name Single output 3 Output wattage 4 Universal input 5 Output voltage 6 *6 T3 : mounting hole M3 J : VH(J.S.T.)connector type J3 : Horizontal input connector VH(J.S.T.)connector type R3 : with Subfeatures ( 5VAUX,VAUX,Remote, Power good) Specification is changed at option, refer to Instruction manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, please handle the unit with care *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL GHA300F- GHA300F-4 GHA300F-48 MAX OUTPUT WATTAGE[W] Forced air at 50C V 5A 4V.5A 48V 6.3A DC OUTPUT Convection at 40C V 8.4A 4V 4.A 48V.A at 50C V 4.5A 4V.A 48V.A SPECIFICATIONS MODEL GHA300F- GHA300F-4 GHA300F-48 VOLTAGE[V] AC90-64 f (output derating is required at AC90V -5V *3) [A] ACIN 0V 3.3typ ACIN 30V.8typ FREQUENCY[Hz] 50 / 60 (47-63) ACIN 0V 89typ 90typ 90typ EFFICIENCY[%] INPUT ACIN 30V 9typ 9typ 9typ POWER FACTOR ACIN 0V 0.95typ (Io=00%) ACIN 30V 0.90typ ACIN 0V 0typ (Io=00%) (At cold start) (Ta=5C) INRUSH [A] ACIN 30V 40typ (Io=00%) (At cold start) (Ta=5C) LEAKAGE [ma] 0.5/0.50max (ACIN 0V/40V 60Hz,Io=00%, According to IEC6060-) VOLTAGE[V] 4 48 [A] Forced air Convection LINE REGULATION[mV] *4 48max 96max 9max LOAD REGULATION[mV] *4 00max 50max 40max RIPPLE[mVp-p] * 0 to +50C 40max 40max 300max -0 to 0C 30max 30max 400max OUTPUT RIPPLE [mvp-p]* 0 to +50C 300max 300max 480max -0 to 0C 360max 360max 500max TEMPERATURE REGULATION[mV] 0 to +50C 0max 40max 480max -0 to +50C 50max 90max 600max DRIFT[mV] * 48max 96max 9max START-UP TIME[ms] 500typ (ACIN 0V, Io=00%) HOLD-UP TIME[ms] 6typ (ACIN 0V, Io=00%) OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 0.80 to to to 5.80 OUTPUT VOLTAGE SETTING[V].00 to to to 49.9 OVER Works over 05% of rating and recovers automatically OVERVOLTAGE [V] 3.80 to to to 67.0 AUX (VA) CIRCUIT AUX (5VA) REMOTE ON/OFF PowerGood INPUT-OUTPUT-RC-AUX *7 AC4,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP ISOLATION INPUT- AC,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP OUTPUT-RC-AUX- *7 AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OUTPUT-RC-AUX *7 AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OPERATING TEMP.,HUMID. ALTITUDE -0 to +70C, 0-90%RH (Non condensing), 3,000m (0,000feet) max *3 ENVIRONMENT STORAGE TEMP.,HUMID. ALTITUDE -30 to +75C, 0-90%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 0-55Hz, 9.6m/s (G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 96.m/s (0G), ms, once each X, Y and Z axis UL60950-, ANSI/AAMI ES6060-, C-UL(CSA60950-, CAN/CSA6060-), EN60950-, EN6060-3rd, SAFETY AGENCY APPROVALS Complies with DEN-AN, IEC th Ed. CONDUCTED Complies with FCC-B, VCCI-B, CISPR-B, CISPR-B, EN550-B, EN550-B REGULATIONS HARMONIC ATTENUATOR Complies with IEC (class A) *5 CASE SIZE/WEIGHT 76.X35X7mm [3.0X.4X5.0 inches] (WXHXD) / 400g max COOLING METHOD Convection, Forced air (Require external fan) * This is the value that measured on measuring board with capacitor of mf at 50mm from output terminal. Measured by 0MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM03). * Drift is the change in DC output for an eight hour period after a half-hour warm-up at 5C, with the input voltage held constant at the rated input/output. *3 Derating is required. *4 Please contact us about dynamic load and input response. *5 Please contact us about another class. *6 Specification is changed at option, refer to Instruction Manual. *7 Applicable when AUX and remote control (optional) is added. * To meet the specifications. Do not operate over-loaded condition. * Sound noise may be generated by power supply in case of pulse load. * Parallel operation is not possible. * Forced air cooling is required to output up to MAX OUTPUT WATTAGE. * Bottom layer P.C.B has electric potential which is required isolation from by clearance or creepage as the safety design issue. GHA-

2 GHA300F Features -High Power density:4.3w/inch 3 -High efficiency 9 typ (Input Voltage 30V, Output Voltage 4V) - "X "standard footprint -Fits U applications -Industrial and Medical safety approvals -Low leakage current -With Remote On/Off () -With AUX (V), AUX (5V) () -No minimum load is required Block diagram AC IN 90-64V FUSE 50V0A BOOSTER INDUCTOR INRUSH LIMIT AUX(V A) DC OUT INTERNAL REGULATOR OVER VOLTAGE PG(POWER GOOD) RC(REMOTE ON/OFF) AUX(5V A) External view * External size of option J3 is different from standard model and refer to 5 Option and Others of instruction manual for details ±0.5 [0.] [4.55] 4-f3.4(with M3) Mating Connector Terminal Mfr connector Standard A-467-A03A Molex * R J BP3-VH VHR-3N SVH-T-P. J.S.T. TB50 OUTPUT(+) JR3 B8B-PHDSS PHDR-08VS SPHD-00T-P [3.00] ±0.5 [0.] [.55] 3 AC(N) AC(L) 9.7 [4.7] 4. [4.89] 7.0 [5.00] Name plate TB50 OUTPUT(-) [0.67] [.50] [0.7] with Subfeatures() Voltage adjust *Please note the pin position No. is different from Molex. Mating connector Terminal Mfr - 50 Series Tyco Electronics <Pin Assignments> <> Pin No. Input AC(L) 3 AC(N) 35 [.38] Tolerance ± [±0.04] Weight : 400g max There is a total of four attachment holes. This power supply requires mounting on metal standoffs 5mm in height. (Insulating sheet is required if you do not use a spacer). Dimensions in mm, [ ]=inches Screw tightening torque : (TB50, 50) :.5N-m max Mounting toque : 0.6N-m max Avoid contact between TB50 and 50 wiring with mounting parts. Option : -J : (J.S.T) connector type. Refer to Instruction Manual [0.65] 4.5 [0.96] <()> Pin No. Function AUX : AUX (VA) AUXG : AUX (GND) 3 RC : REMOTE ON/OFF 4 RCG : REMOTE ON/OFF (GND) 5 PG : Power good 6 PGG : Power good (GND 7 AUX : AUX (5VA) 8 AUXG : AUX (GND) 8 7 GHA-3

3 AC-DC Power Supplies Medical Type GHA500F Ordering information GH A 500 F -OO -O R This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, please handle the unit with care *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. Series name Single output 3 Output wattage 4 Universal input 5 Output voltage 6 *6 T3 : mounting hole M3 J : VH(J.S.T.)connector type J3 : Horizontal input connector VH(J.S.T.)connector type R3 : with Subfeatures ( 5VAUX,VAUX,Remote, Power good) P : Parallel Operation Specification is changed at option, refer to Instruction manual. MODEL GHA500F- GHA500F-5 GHA500F-4 GHA500F-30 GHA500F-48 GHA500F-56 MAX OUTPUT WATTAGE[W] Forced air at 50C V 4.7A 5V 33.4A 4V.0A 30V 6.7A 48V 0.5A 56V 9.0A Convection at 40C V.5A 5V 0.0A 4V 6.3A 30V 5.0A 48V 3.A 56V.7A DC OUTPUT at 50C V 9.A 5V 7.4A 4V 4.6A 30V 3.7A 48V.3A 56V.9A conduction at 0C V 30.0A 5V 4.0A 4V 5.0A 30V.0A 48V 7.5A 56V 6.4A cooling at 50C V 6.7A 5V 3.4A 4V 8.4A 30V 6.7A 48V 4.A 56V 3.6A SPECIFICATIONS Example recommended EMI/EMC filter EAC-0-47 High voltage pulse noise type : EAP series Low leakage current type : EAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. MODEL GHA500F- GHA500F-5 GHA500F-4 GHA500F-30 GHA500F-48 GHA500F-56 VOLTAGE[V] AC90-64 f (output derating is required at AC90V -5V *3) [A] ACIN 0V 5.4typ ACIN 30V.9typ FREQUENCY[Hz] 50 / 60 (47-63) ACIN 0V 88typ 90typ 90typ 90typ 90typ 90typ EFFICIENCY[%] INPUT ACIN 30V 90typ 9typ 9typ 9typ 9typ 9typ POWER FACTOR ACIN 0V 0.95typ (Io=00%) ACIN 30V 0.90typ ACIN 0V 0typ (Io=00%) (At cold start) (Ta=5C) INRUSH [A] ACIN 30V 40typ (Io=00%) (At cold start) (Ta=5C) LEAKAGE [ma] 0.5/0.50max (ACIN 0V/40V 60Hz,Io=00%, According to IEC6060-) VOLTAGE[V] Forced air [A] Convection conduction cooling LINE REGULATION[mV] *4 48max 60max 96max 0max 9max 9max LOAD REGULATION[mV] *4 00max 0max 50max 80max 40max 40max RIPPLE[mVp-p] * 0 to +50C 40max 40max 40max 300max 300max 400max -0-0C 30max 30max 30max 400max 400max 500max OUTPUT 0 to +50C 300max 300max 300max 480max 480max 500max RIPPLE [mvp-p]* -0-0C 360max 360max 360max 500max 500max 580max TEMPERATURE REGULATION[mV] 0 to +50C 0max 50max 40max 300max 480max 480max -0 to +50C 50max 80max 90max 360max 600max 600max DRIFT[mV] * 48max 60max 96max 0max 9max 9max START-UP TIME[ms] 500typ (ACIN 0V, Io=00%) HOLD-UP TIME[ms] 6typ (ACIN 0V, Io=00%) OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 0.80 to to to to to to OUTPUT VOLTAGE SETTING[V].00 to to to to to to OVER Works over 05% of rating and recovers automatically OVERVOLTAGE [V] 3.80 to to to to to to AUX (VA) CIRCUIT AUX (5VA) REMOTE ON/OFF PowerGood INPUT-OUTPUT-RC-AUX *7 AC4,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP ISOLATION INPUT- AC,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP OUTPUT-RC-AUX- *7 AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OUTPUT-RC-AUX *7 AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OPERATING TEMP.,HUMID. ALTITUDE -0 to +80C, 0-90%RH (Non condensing), 3,000m (0,000feet) max ENVIRONMENT STORAGE TEMP.,HUMID. ALTITUDE -30 to +80C, 0-90%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 0-55Hz, 9.6m/s (G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 96.m/s (0G), ms, once each X, Y and Z axis SAFETY AGENCY APPROVALS UL60950-, ANSI/AAMI ES6060-, C-UL(CSA60950-, CAN/CSA6060-), EN60950-, EN6060-3rd, Complies with DEN-AN, IEC th Ed. CONDUCTED Complies with FCC-B, VCCI-B, CISPR-B, CISPR-B, EN550-B, EN550-B REGULATIONS HARMONIC ATTENUATOR Complies with IEC (class A) *5 CASE SIZE/WEIGHT 76.X35X7mm [3.0X.4X5.0 inches] (WXHXD) / 40g max COOLING METHOD Convection, Forced air (Require external fan), Conduction cooling * This is the value that measured on measuring board with capacitor of mf at 50mm from output terminal. Measured by 0MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM03). * Drift is the change in DC output for an eight hour period after a half-hour warm-up at 5C, with the input voltage held constant at the rated input/output. *3 Derating is required. *4 Please contact us about dynamic load and input response. GHA-4 *5 Please contact us about another class. *6 Specification is changed at option, refer to Instruction Manual. *7 Applicable when AUX and remote control (optional) is added. * To meet the specifications. Do not operate over-loaded condition. * Sound noise may be generated by power supply in case of pulse load. * Parallel operation is available with -P option. Refer to 5.on the instruction manual. * Forced air cooling is required to output up to MAX OUTPUT WATTAGE.

4 GHA500F Features -Wattage 500W max -High Power density:4.w/inch 3 -High efficiency 9 typ (Input Voltage 30V,Output Voltage 4V) -Conduction cooling - "X "standard footprint -Fits U applications -Industrial and Medical safety approvals -Low leakage current -With Remote On/Off () -With AUX (V), AUX (5V) () -No minimum load is required Block diagram AC IN 90-64V FUSE 50V0A BOOSTER INDUCTOR INRUSH LIMIT AUX(V A) DC OUT INTERNAL REGULATOR OVER VOLTAGE PG(POWER GOOD) RC(REMOTE ON/OFF) AUX(5V A) External view * External size of option J3 is different from standard model and refer to 5 Option and Others of instruction manual for details ±0.5 4-f3.4(with M3) [0.] [4.55] Mating Connector Terminal Mfr connector Standard A-467-A03A Molex * R ± [3.00] [0.] [.55] 35 [.38] 3 AC(N) AC(L) 9.7 [4.7] 4. [4.89] 7.0 [5.00] Name plate Tolerance ± [±0.04] Weight : 40g max There is a total of four attachment holes. Base Plate : Aluminum Dimensions in mm, [ ]=inches Screw tightening torque : (TB50, 50) :.5N-m max Mounting toque : 0.6N-m max Avoid contact between TB50 and 50 wiring with mounting parts. Option : -J : (J.S.T) connector type. Refer to Instruction Manual 5. TB50 OUTPUT(+) TB50 OUTPUT(-) [0.67] [.50] [0.7] with Subfeatures() Voltage adjust 6.5 [0.65] 4.5 [0.96] JR3 B8B-PHDSS PHDR-08VS SPHD-00T-P0.5 J BP3-VH VHR-3N SVH-T-P. J.S.T. *Please note the pin position No. is different from Molex. Mating connector Terminal Mfr - 50 Series Tyco Electronics <Pin Assignments> <> Pin No. Input AC(L) 3 AC(N) <()> Pin No. Function AUX : AUX (VA) AUXG : AUX (GND) 3 RC : REMOTE ON/OFF RCG : REMOTE ON/OFF (GND) 5 PG : Power good 6 PGG : Power good (GND 7 AUX : AUX (5VA) 8 AUXG : AUX (GND) GHA-5

5 AC-DC Power Supplies Medical Type GHA300F-SNF Ordering information GH A 300 F -OO -SNFO R Example recommended EMI/EMC filter EAC-0-47 High voltage pulse noise type : EAP series Low leakage current type : EAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. Series name Single output 3 Output wattage 4 Universal input 5 Output voltage 6 *6 J : PH(J.S.T.)connector type Refer to the instruction manual 5.. *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL GHA300F--SNF GHA300F-4-SNF GHA300F-48-SNF MAX OUTPUT WATTAGE[W] DC OUTPUT Forced air +50C V 5.0A 4V.5A 48V 6.3A SPECIFICATIONS MODEL GHA300F--SNF GHA300F-4-SNF GHA300F-48-SNF VOLTAGE[V] AC90-64 f (output derating is required at AC90V -5V *3) [A] ACIN 0V 3.3typ ACIN 30V.8typ FREQUENCY[Hz] 50 / 60 (47-63) ACIN 0V 88typ 89typ 89typ EFFICIENCY[%] INPUT ACIN 30V 90typ 9typ 9typ POWER FACTOR ACIN 0V 0.95typ (Io=00%) ACIN 30V 0.90typ ACIN 0V 0typ (Io=00%) (At cold start) (Ta=5C) INRUSH [A] ACIN 30V 40typ (Io=00%) (At cold start) (Ta=5C) LEAKAGE [ma] 0.5/0.50max (ACIN 0V/40V 60Hz,Io=00%, According to IEC6060-) VOLTAGE[V] 4 48 [A] Forced air LINE REGULATION[mV] *4 48max 96max 9max LOAD REGULATION[mV] *4 00max 50max 40max RIPPLE[mVp-p] * 0 to +50C 40max 40max 300max -0-0C 30max 30max 400max 0 to +50C 300max 300max 480max RIPPLE [mvp-p]* OUTPUT -0-0C 360max 360max 500max TEMPERATURE REGULATION[mV] 0 to +50C 0max 40max 480max -0 to +50C 50max 90max 600max DRIFT[mV] * 48max 96max 9max START-UP TIME[ms] 500typ (ACIN 0V, Io=00%) HOLD-UP TIME[ms] 6typ (ACIN 0V, Io=00%) OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 0.80 to to to 5.80 OUTPUT VOLTAGE SETTING[V].00 to to to 49.9 CIRCUIT OVER Works over 05% of rating and recovers automatically *7 OVERVOLTAGE [V] 3.80 to to to 67.0 AUX 0V 0.5A AUX 5V A REMOTE ON/OFF Possible, AUX is available PowerGood Open corrector INPUT-OUTPUT-RC-AUX AC4,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP ISOLATION INPUT- AC,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP OUTPUT-RC-AUX- AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OUTPUT-RC-AUX AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OPERATING TEMP.,HUMID. ALTITUDE -0 to +70C, 0-90%RH (Non condensing), 3,000m (0,000feet) max *3 ENVIRONMENT STORAGE TEMP.,HUMID. ALTITUDE -30 to +75C, 0-90%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 0-55Hz, 9.6m/s (G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 96.m/s (0G), ms, once each X, Y and Z axis UL60950-, ANSI/AAMI ES6060-, C-UL(CSA60950-, CAN/CSA6060-), EN60950-, EN6060-3rd, SAFETY AGENCY APPROVALS Complies with DEN-AN, IEC th Ed. CONDUCTED Complies with FCC-B, VCCI-B, CISPR-B, CISPR-B, EN550-B, EN550-B REGULATIONS HARMONIC ATTENUATOR Complies with IEC (class A) *5 CASE SIZE/WEIGHT 85.X4X65.3mm [3.35X.6X6.5 inches] (WXHXD) / 60g max COOLING METHOD Forced air * This is the value that measured on measuring board with capacitor of mf at 50mm from output terminal. Measured by 0MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM03). * Drift is the change in DC output for an eight hour period after a half-hour warm-up at 5C, with the input voltage held constant at the rated input/output. *3 Derating is required. *4 Please contact us about dynamic load and input response. GHA-6 *5 Please contact us about another class. *6 Specification is changed at option, refer to Instruction Manual. *7 When output current more than rated, output will shut down after 5 seconds or more. Recycle input after 3 minutes to reset the protection. * To meet the specifications. Do not operate over-loaded condition. * Sound noise may be generated by power supply in case of pulse load.

6 GHA300F-SNF Features -Full packaged desin united with GHA's features and addtional robastness.. -High efficiency 9% typ (Input voltage 30V,Output voltage 4V) -Optical for U applications -Medical and Industrial safety approvals -Low leakage current -Conformal coating -Single remote ON/OFF control for DC output, AUX and Fan. -Isolated dual AUX (AUX 0V 0.5A, AUX 5V A) Block diagram AC IN 90-64V FUSE 50V0A BOOSTER INDUCTOR INRUSH LIMIT AUX(0V 0.5A) DC OUT INTERNAL REGULATOR OVER VOLTAGE PG(POWER GOOD) RC(REMOTE ON/OFF) AUX(5V A) External view Output voltage adjust Output(-) Output(+) Point A 3.3 [0.9] 7 8 [.46] 85. [3.35] [.00] 7 [0.67] [.00] Name plate -M4 (Bottom side) GHA M4 (AC,) Cover 0.5 [0.4] 8.6 [0.34] 0.5 [0.4] 53 [.0].6 [0.85] CAUTION DOUBLE POLE/NEUTRAL FUSING AC(N) AC(L).8 [0.90] 6 [0.4] 34.5 ±0.5 7max [5.30±0.0] 65.3 [0.67max] [6.50] ±0.5 [0.60] [4.55±0.0] 4 ±0.5 [.6±0.0] 9.5 [0.37] M4 (Output(+),Output(-)) Tolerance ± [±0.04] Weight : 60g max Upper PCB Material/thickness : FR-4/.6mm Lower PCB Material/thickness : FR-4/.6mm Chassis Material/thickness : Aluminum/.5mm Cover Material/thickness : Aluminum/.mm Fan cover Material : PBT Mounting torque :.5N m (4.7kgf cm) max Screw tightening torque M4 :.6N m (6.9kgf cm) max Dimensions in mm, [ ]=inches 8max [0.70max] AIR FLOW -M4 8 7 < mating connector and terminal> Connector Mating connector Terminal Mfr SNF Molex * SNFJ S8B-PHDSS PHDR-08VS SPHD-00T-P0.5 J.S.T. *Please note the pin position No. is different from Molex. <> Pin No. Function AUX : AUX (0V0.5A) AUXG : AUX (GND) 3 RC : REMOTE ON/OFF 4 RCG : REMOTE ON/OFF (GND) 5 PG : Power good 6 PGG : Power good (GND 7 AUX : AUX (5VA) 8 AUXG : AUX (GND) GHA-7

7 AC-DC Power Supplies Medical Type GHA500F-SNF Ordering information GH A 500 F -OO -SNFO R Example recommended EMI/EMC filter EAC-0-47 High voltage pulse noise type : EAP series Low leakage current type : EAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. Series name Single output 3 Output wattage 4 Universal input 5 Output voltage 6 *6 J : PH(J.S.T.)connector type P : Parallel Operation Refer to the instruction manual 5.. *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL GHA500F--SNF GHA500F-5-SNF GHA500F-4-SNF GHA500F-30-SNF GHA500F-48-SNF GHA500F-56-SNF MAX OUTPUT WATTAGE[W] DC OUTPUT Forced air +50C V 37.5A 5V 33.4A 4V.0A 30V 6.7A 48V 0.5A 56V 9.0A SPECIFICATIONS MODEL GHA500F--SNF GHA500F-5-SNF GHA500F-4-SNF GHA500F-30-SNF GHA500F-48-SNF GHA500F-56-SNF VOLTAGE[V] AC90-64 f (output derating is required at AC90V -5V *3) [A] ACIN 0V 4.8typ 5.4typ ACIN 30V.6typ.9typ FREQUENCY[Hz] 50 / 60 (47-63) ACIN 0V 87typ 89typ 89typ 89typ 89typ 89typ EFFICIENCY[%] INPUT ACIN 30V 89typ 9typ 9typ 9typ 9typ 9typ POWER FACTOR ACIN 0V 0.95typ (Io=00%) ACIN 30V 0.90typ ACIN 0V 0typ (Io=00%) (At cold start) (Ta=5C) INRUSH [A] ACIN 30V 40typ (Io=00%) (At cold start) (Ta=5C) LEAKAGE [ma] 0.5/0.50max (ACIN 0V/40V 60Hz,Io=00%, According to IEC6060-) VOLTAGE[V] [A] Forced air LINE REGULATION[mV] *4 48max 60max 96max 0max 9max 9max LOAD REGULATION[mV] *4 00max 0max 50max 80max 40max 40max RIPPLE[mVp-p] * 0 to +50C 40max 40max 40max 300max 300max 400max -0-0C 30max 30max 30max 400max 400max 500max 0 to +50C 300max 300max 300max 480max 480max 500max RIPPLE [mvp-p]* OUTPUT -0-0C 360max 360max 360max 500max 500max 580max TEMPERATURE REGULATION[mV] 0 to +50C 0max 50max 40max 300max 480max 480max -0 to +50C 50max 80max 90max 360max 600max 600max DRIFT[mV] * 48max 60max 96max 0max 9max 9max START-UP TIME[ms] 500typ (ACIN 0V, Io=00%) HOLD-UP TIME[ms] 6typ (ACIN 0V, Io=00%) OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 0.80 to to to to to to OUTPUT VOLTAGE SETTING[V].00 to to to to to to CIRCUIT OVER Works over 05% of rating and recovers automatically *7 OVERVOLTAGE [V] 3.80 to to to to to to AUX V 0.5A AUX 5V A REMOTE ON/OFF Possible, AUX is available PowerGood Open corrector INPUT-OUTPUT-RC-AUX AC4,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP ISOLATION INPUT- AC,000V minute, Cutoff current = 0mA, DC500V 50MW min (At Room Temperature) MOPP OUTPUT-RC-AUX- AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OUTPUT-RC-AUX AC500V minute, Cutoff current = 5mA, DC500V 50MW min (At Room Temperature) OPERATING TEMP.,HUMID. ALTITUDE -0 to +70C, 0-90%RH (Non condensing), 3,000m (0,000feet) max *3 ENVIRONMENT STORAGE TEMP.,HUMID. ALTITUDE -30 to +80C, 0-90%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 0-55Hz, 9.6m/s (G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 96.m/s (0G), ms, once each X, Y and Z axis UL60950-, ANSI/AAMI ES6060-, C-UL(CSA60950-, CAN/CSA6060-), EN60950-, EN6060-3rd, SAFETY AGENCY APPROVALS Complies with DEN-AN, IEC th Ed. CONDUCTED Complies with FCC-B, VCCI-B, CISPR-B, CISPR-B, EN550-B, EN550-B REGULATIONS HARMONIC ATTENUATOR Complies with IEC (class A) *5 CASE SIZE/WEIGHT 85.X4X65.3mm [3.35X.6X6.5 inches] (WXHXD) / 660g max COOLING METHOD Forced air * This is the value that measured on measuring board with capacitor of mf at 50mm from output terminal. Measured by 0MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM03). * Drift is the change in DC output for an eight hour period after a half-hour warm-up at 5C, with the input voltage held constant at the rated input/output. *3 Derating is required. *4 Please contact us about dynamic load and input response. GHA-8 *5 Please contact us about another class. *6 Specification is changed at option, refer to Instruction Manual. *7 When output current more than rated, output will shut down after 5 seconds or more. Recycle input after 3 minutes to reset the protection. * To meet the specifications. Do not operate over-loaded condition. * Sound noise may be generated by power supply in case of pulse load. * Parallel operation is available with -P option. Refer to 5.on the instruction manual.

8 GHA500F-SNF Features -Full packaged design united with GHA's features, and additional robustness.. -High efficiency 9% typ (Input voltage 30V,Output voltage 4V) -50% minimized size compares with previous products. -Optical for U applications -Medical and Industrial safety approvals -Low leakage current -Conformal coating -Single remote ON/OFF control for DC output, AUX and Fan. -Isolated dual AUX (AUX V 0.5A, AUX 5V A) Block diagram AC IN 90-64V FUSE 50V0A BOOSTER INDUCTOR INRUSH LIMIT AUX(V 0.5A) DC OUT INTERNAL REGULATOR OVER VOLTAGE PG(POWER GOOD) RC(REMOTE ON/OFF) AUX(5V A) External view Output voltage adjust Output(-) Output(+) Point A 3.3 [0.9] 7 8 [.46] 85. [3.35] [.00] 7 [0.67] [.00] Name plate -M4 (Bottom side) GHA M4 (AC,) Cover 0.5 [0.4] 8.6 [0.34] 0.5 [0.4] 53 [.0].6 [0.85] CAUTION DOUBLE POLE/NEUTRAL FUSING AC(N) AC(L).8 [0.90] 6 [0.4] 34.5 ±0.5 7max [5.30±0.0] 65.3 [0.67max] [6.50] ±0.5 [0.60] [4.55±0.0] 4 ±0.5 [.6±0.0] 9.5 [0.37] M4 (Output(+),Output(-)) Tolerance ± [±0.04] Weight : 660g max Upper PCB Material/thickness : FR-4/.6mm Lower PCB Material/thickness : AL/.5mm Chassis Material/thickness : Aluminum/.5mm Cover Material/thickness : Aluminum/.mm Fan cover Material : PBT Mounting torque :.5N m (4.7kgf cm) max Screw tightening torque M4 :.6N m (6.9kgf cm) max Dimensions in mm, [ ]=inches 8max [0.70max] AIR FLOW -M4 8 7 < mating connector and terminal> <> Pin No. Connector Mating connector Function AUX : AUX (V0.5A) AUXG : AUX (GND) 3 RC : REMOTE ON/OFF 4 RCG : REMOTE ON/OFF (GND) 5 PG : Power good 6 PGG : Power good (GND 7 AUX : AUX (5VA) 8 AUXG : AUX (GND) Terminal Mfr SNF Molex * SNFJ S8B-PHDSS PHDR-08VS SPHD-00T-P0.5 J.S.T. *Please note the pin position No. is different from Molex. GHA-9