1000ms, 50ms/230VAC 2500ms, 50ms/115VAC at full load. LEAKAGE CURRENT Earth leakage current < 300μA/264VAC, Touch leakage current < 100μA/264VAC

Transcription

1 MSP-600_ EH-07 SPECIFICATION MODEL OUTPUT INPUT SAFETY EMC (Note 4) MSP MSP MSP MSP-600- MSP MSP MSP MSP DC VOLTAGE.V 5V 7.5V V 5V 4V 6V 48V RATED CURRENT A A 80A 5A 4A 7A 7.5A A CURRENT RANGE 0 ~ A 0 ~ A 0 ~ 80A 0 ~ 5A 0 ~ 4A 0 ~ 7A 0 ~ 7.5A 0 ~ A RATED POWER 6W 600W 600W 66W 645W 648W 60W 64W RIPPLE NOISE (max.) Note. 0mVp-p 0mVp-p 0mVp-p mvp-p 50mVp-p 50mVp-p 00mVp-p 40mVp-p VOLTAGE ADJ. RANGE.8 ~.8V 4. ~ 5.8V 6.8 ~ V. ~.8V.5 ~ 8V.6 ~ 8.8V 8.8 ~.6V 40.8 ~ 55.V VOLTAGE TOLERANCE Note. ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.% ±0.% ±0.% ±0.% ±0.% LOAD REGULATION ±.0% ±.0% ±.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 00ms, 50ms/0VAC 500ms, 50ms/5VAC at full load HOLD UP TIME (Typ.) 6ms/0VAC 6ms/5VAC at full load VOLTAGE RANGE Note.5 85 ~ 64VAC ~ 70VDC FREQUENCY RANGE 47 ~ 6Hz POWER FACTOR (Typ.) PF>0.4/0VAC PF>0./5VAC at full load EFFICIENCY (Typ.) 78.5% 8% 86% 88% 88% 88% 8% 8% AC CURRENT (Typ.) 8.5A/5VAC 5A/0VAC INRUSH CURRENT (Typ.) 5A/5VAC 80A/0VAC LEAKAGE CURRENT Earth leakage current < 00μA/64VAC, Touch leakage current < 0μA/64VAC OVERLOAD 5 ~ 5% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTION.6 ~ 4.6V 6 ~ 7V.4 ~.V 4.4 ~ 6.8V 8.8 ~.8V 0 ~ 4.8V 4.4 ~ 48.6V 57.6 ~ 67.V OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down 5V STANDBY 5VSB : 5V@0.A ; tolerance± 5%, ripple : 50mVp-p(max.) FUNCTION DC OK SIGNAL PSU turn on :. ~ 5.6V ; PSU turn off : 0 ~ V REMOTE / : 4 ~ V or open = power on ; 0 ~ 0.8V or short = power off FAN (Typ.) Load 5± 5% or RTH 50 Fan on WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve") WORKING HUMIDITY 0 ~ 0% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85, ~ 5% RH TEMP. COEFFICIENT ± 0.0%/ (0 ~ 50 ) VIBRATION ~ 500Hz, 5G min./cycle, 60min. each along X, Y, Z axes OTHERS NOTE SAFETY STANDARDS ISOLATION LEVEL WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION ANSI/AAMI ES6060-, IEC6060- approved Primaryecondary: MOOP, Primary-Earth: MOOP, Secondary-Earth: MOOP I/P-O/P:4KVAC I/P-FG:KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:0M Ohms / 500VDC / 5 / 70% RH Compliance to EN550 (CISPR) Class B, EN600--,- Compliance to EN600-4-,,4,5,6,8,, EN K hrs min. MIL-HDBK-7F (5 ) 8*5*6.5mm (L*W*H) PACKING.57Kg;8pcs/.6Kg/.4CUFT File Name:MSP-600PEC

2 MSP-600_ EH-07 Mechanical Specification Case No. 77A Unit:mm Air flow direction 8. I/P M4 L= O/P LED (Vo ADJ.)SVR max. 8-M4 L=4 (Both Sides) 8max AC Input Terminal Pin No. Assignment Pin No. Assignment DC Output Terminal Pin No. Assignment Pin No. Assignment AC/L ~ -V AC/N 4~6 +V FG Block Diagram I/P FG EMI Derating Curve ACTIVE INRUSH CURRENT LIMITING PFC O.T.P. PFC Connector Pin No. Assignment() : HRS DF-DP-DS or equivalent Pin No. Assignment Pin No. Assignment Mating Housing Terminal AUXG 6,8 GND AUX 7 DC-OK HRS DF-DS HRS DF-**SC or equivalent or equivalent 4 5 CS AUX POWER POWER SWITCHING O.L.P. PWM DETECTION CIRCUIT O.T.P. O.V.P. REMOTE Output Derating VS Input Voltage PWM fosc : 70KHz CURRENT SHARING AUX AUXG +V -V DC OK CS LOAD (%) 50 0 LOAD(%) AMBIENT TEMPERATURE ( ) (HORIZONTAL) INPUT VOLTAGE (V) 60Hz File Name:MSP-600PEC

3 MSP-600_ EH-07 Function Description of Pin No. Function Description AUXG Auxiliary voltage output ground. The signal return is isolated from the output terminals (+V -V). AUX Auxiliary voltage output, 4.75~5.5V, referenced to pin (AUXG). The maximum load current is 0.A. This output is not controlled by the "remote ON/OFF control". 4 Turns the output on and off by electrical or dry contact between pin 4 (), Short: Power OFF, Open: Power ON. Remote control ground. 5 CS Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance between units. 6,8 GND This pin connects to the negative terminal(-v). Return for DC-OK signal output. 7 DC-OK DC-OK signal is a TTL level signal, referenced to pin8(dc-ok GND). High when PSU turns on. Positive sensing. The signal should be connected to the positive terminal of the load. The and leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The signal should be connected to the negative terminal of the load. The and leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Function Manual.Remote Sense The remote sensing compensates voltage drop on the load wiring up to 0.5V. AUX AUXG GND CS + - (Pin) LOAD (Pin) Fig. Sense lines should be twisted in pairs.dc-ok Signal DC-OK signal is a TTL level signal. High when PSU turns on. Between DC-OK(pin7) and GND(pin6,8). ~ 5.6V 0 ~ V Output Status ON OFF AUX AUXG GND CS Fig. File Name:MSP-600PEC

4 MSP-600_ EH-07.Remote Control The PSU can be turned ON/OFF by using the "Remote Control" function. Between (pin) and (pin4) SW ON (Short) SW OFF (Open) Output Status OFF ON SW Fig. 4.Current Sharing with Remote Sensing (Only for 4V, 6V and 48V) MSP-600 has the built-in active current sharing function and can be connected in parallel to provide higher output power : ()Parallel operation is available by connecting the units shown as below. (,,CS and GND are connected mutually in parallel). ()Difference of output voltages among parallel units should be less than %. ()The total output current must not exceed the value determined by the following equation. (output current at parallel operation)=(rated current per unit) (Number of unit) 0. (4)In parallel operation 4 units is the maximum, please consult the manufacturer for applications of more connecting in parallel. (5)The power supplies should be paralleled using short and large diameter wiring and then connected to the load. PSU PSU PSU PSU4 -V -V -V -V +V +V +V +V PSU PSU PSU PSU4 AUX AUXG GND CS AUXG CS DC-OK AUXG CS DC-OK AUXG CS DC-OK AUXG CS DC-OK AUX GND GND AUX GND GND AUX GND GND AUX GND GND +V -V LOAD Sense lines should be twisted in pairs Fig 4. Note :.In parallel connection, maybe only one unit (master) operate if the total output load is less than % of rated load condition. The other PSU (slave) may go into standby mode and its output LED and relay will not turn on..% min. of dummy load is required. File Name:MSP-600PEC

5 Headquarter Switzerland: Pewatron AG Thurgauerstrasse 66 CH-8050 Zurich Phone info@pewatron.com Office Germany: Pewatron Deutschland GmbH Edisonstraße 6 D-8576 Unterschleißheim Phone info.de@pewatron.com We are here for you. Addresses and Contacts. Sales Germany Austria Postcode Postcode 8000 Postcode Austria Kurt Stritzelberger Phone Mobile kurt.stritzelberger@pewatron.com Postcode Postcode Gerhard Vetter Phone Mobile gerhard.vetter@pewatron.com Geometrical sensors Sensor elements Thorsten Ravagni Phone thorsten.ravagni@pewatron.com Sales Switzerland Liechtenstein Postcode 000 Basil Frei Phone Mobile basil.frei@pewatron.com Postcode 00 Christian Mohrenstecher Mobile christian.mohrenstecher@pewatron.com Sales International Key Accounts Peter Felder Phone Mobile peter.felder@pewatron.com Sales Other Countries / Product Management Pressure Sensors Philipp Kistler Phone philipp.kistler@pewatron.com Gas sensors / Gas sensor modules Load cells Thomas Clausen Phone thomas.clausen@pewatron.com Linear position sensors Angle sensors Eric Letsch Phone eric.letsch@pewatron.com Accelerometers / Level Flow sensor elements Thorsten Ravagni Phone thorsten.ravagni@pewatron.com Power supplies Sebastiano Leggio Phone sebastiano.leggio@pewatron.com Current sensors Power solutions Osman Coban Phone osman.coban@pewatron.com Drive technology CH Postcode 5000 / DE Roman Homa Mobile roman.homa@pewatron.com Drive technology CH Postcode 00 4 / AT / IT / FR Christian Mohrenstecher Mobile christian.mohrenstecher@pewatron.com Competitive sensor power supply solutions worldwide