CLASS-T DIGITAL AUDIO AMPLIFIER MINI REFERENCE BOARD USING DIGITAL POWER PROCESSING TM TECHNOLOGY
|
|
- Vincent Horton
- 6 years ago
- Views:
Transcription
1 Tripath Technology, Inc. - Technical Information RB-TA CLASS-T DIGITAL AUDIO AMPLIFIER MINI REFEREE BOARD USING DIGITAL POWER PROCESSING TM TECHNOLOGY Technical Information Rev B January 2003 Introduction Measuring only 1.2 x 1.6, the Mini TA2024 (RB-TA ) was created to provide the systems designer with a minimal footprint reference for use in space-constrained applications of the TA2024 2x15W high efficiency amplifier. The board is a complete TA2024 2x15W circuit, ready to evaluate. It needs only power, signal and passive speakers to be up and running. Connection and Operation Below is a simple diagram showing the input and output connection requirements of the RB-TA The +12V supply must not exceed 13.2V at any time, or damage to the device may occur. A low level stereo signal source, such as a portable MP3 or CD player can be used for the input, while normal passive bookshelf or home theater speakers (4 ohms minimum) can be used for the outputs. Application Information When playing music, lower output power levels can be sustained indefinitely, while higher levels can be played for only a limited time due to the small size of the copper area of the pc board. The TA2024 is extremely efficient, approaching 90% with an 8Ω load; however, the dissipated power inside the TA2024, though relatively small, still generates heat. This heat conducts through the TA2024 s heat slug and onto the pc board area to which the heat slug is soldered. In final end applications, the TA2024 and its associated components will be part of a larger system design where more heat sinking area will be available, via multi layers or larger ground plane, or both. Please consult the TA2024 datasheet for more information on power dissipation requirements. Warning: The intended purpose of the RB-TA is to show a minimum footprint application for TA2024 and its associated components. Though it is a fully functional design, it is NOT intended to be used as a standalone amplifier product. For final product application, please consult the Power Dissipation section in the TA2024 datasheet for necessary thermal requirements. +12V GND CH1 GND OUT1+ OUT1- CH2 OUT2- OUT2+ NOTE: Board shown ACTUAL SIZE when printed on 8.5 x 11 paper Browse our extensive range of Tripath and other audio parts at 1 RB-TA
2 Tripath Technology, Inc. - Technical Information Contact Information TRIPATH TECHNOLOGY, I 2560 Orchard Parkway, San Jose, CA P F For more Sales Information, please visit For more Technical Information, please visit Browse our extensive range of Tripath and other audio parts at 2 RB-TA
3 A 1 1 A L5 12V+ J9 BEAD C21 GND J10 12V+ GND U2 TA V_PLANE C17 1uF 0.1u C GEN DCAP2 DCAP1 CPUMP PGND C5 1uF +12V_PLANE L8 10uH C27 C12 C8 J5 OUT1+ J3 IN1 J14 GND L1 C23 BEAD 1uF C14 1uF C15 20K R2 20K R4 R5 R6 40k 40k 4 V5D R7 8.2K, 1% 5 AGND1 32 R C28 10 REF OUTP1 L6 7 OVERLOADB VDD1 30 C19 470u_25V 8 AGND2 VDD uH 9 V5A OUTM VP1 OUTM IN1 VDD2 26 C7 12 MUTE VDD u L7 13 OUTP uH VP2 IN2 DGND C6 0.1u C25 C O P P E R A R E A * VDDA 33 + C13 C29 0.1uF C10 C9 J6 J7 OUT1- OUT2+ J4 IN2 L2 C24 BEAD C26 0.1u BIASCAP AGND3 PGND2 18 SLEEP FAULT L9 10uH C22 R10 10 C30 0.1uF C11 J8 OUT2- R11 0ohms R3 0ohms Title TRIPATH TECHNOLOGY I. TA2024 MINI Size Document Number Rev B <Doc> B Date: Wednesday, February 27, 2002 Sheet 1 of 1 Browse our extensive range of Tripath and other audio parts at
4 TA2024 Mini Eval Board Bill Of Materials MC 2/13/2003 Quantity Reference Part Size Digikey Manufacturer Manufact. Part # 2 C17,C5 1uF 16V CERAMIC X7R ND Yageo America 12062R105K7BB0D 4 C6,C7,C16,C26, C29, C30 0.1uF 50V CERAMIC X7R ND Yageo America 08052R104K9BB0D 7 C8,C9,C10,C11,C21,C23, Ceramic NPO 603 PCC101ACVCT-ND Panasonic ECJ-1VC1H101J C24 6 C12,C13,C22,C25,C27,C28 16V CERAMIC X7R PCC1818CT-ND Panasonic ECG ECJ-2YB1C474K 2 C14,C15 1uF 16V CERAMIC X7R ND Yageo America 12062R105K7BB0D 1 C19 470uF Electrolytic 25V G PCE3189CT-ND Panasonic ECE-V1EA471P 3 L1,L2,L5 Ferrite Bead FBM2125 BEAD CORE 4A 100 MHZ 0805 P10191CT-ND Panasonic ECG EXC-ML20A390U 4 L6,L7,L8,L9 Power INDUCTOR FIXED 10UH 2A 10% TOKO 8RHB2 or ISI RL \400 TK4467-ND Toko America 822MY-100K (8RHB2) 2 R4,R2 20K 603 P203HTR-ND Panasonic ERJ-3EKF2002V 2 R11,R3 0ohms 603 P0HTR-ND Panasonic ERJ-3EKF0000V 2 R6,R5 40k 603 P403HTR-ND Panasonic ERJ-3EKF4002V 1 R7 8.2K, 1% 603 P822HTR-ND Panasonic ERJ-3EKF8201V 2 R10,R9 10, 1/8W 805 P10ETR-ND Panasonic ERJ-6ENF1000V 1 U2 TA2024 Browse our extensive range of Tripath and other audio parts at
5
6
7
8
9
TECHNICAL INFORMATION
Class-T Digital Audio Amplifier Evaluation Board using Digital Power Processing TM Technology EB-TA1101B February 2001, for Board Rev E General Description The EB-TA1101B evaluation board is based on the
More informationTECHNICAL INFORMATION
Class-T Digital Audio Amplifier Evaluation Board using Digital Power Processing TM Technology EB-TA2020 February 2001, Rev D General Description The EB-TA2020 evaluation platform is based on the TA2020-020
More informationEB-TA2022 CLASS-T DIGITAL AUDIO AMPLIFIER 2 CHANNEL TA2022 EVALUATION BOARD
Tripath Technology, Inc. - Technical Information EB-TA0 CLASS-T DIGITAL AUDIO AMPLIFIER CHANNEL TA0 EVALUATION BOARD Technical Information Revision.0 March 00 GENERAL DESCRIPTION The EB-TA0 Version.0 is
More informationEB-TA2022 CLASS-T DIGITAL AUDIO AMPLIFIER 2 CHANNEL TA2022 EVALUATION BOARD
Tripath Technology, Inc. - Technical Information EB-TA0 CLASS-T DIGITAL AUDIO AMPLIFIER CHANNEL TA0 EVALUATION BOARD Technical Information Revision.0 March 00 GENERAL DESCRIPTION The EB-TA0 Version.0 is
More informationTECHNICAL INFORMATION Revision 0.96 July 2005
TAA8 STEREO 9W (8Ω) CLASS-T DIGITAL AUDIO AMPLIFIER USING DIGITAL POWER PROCESSING TECHNOLOGY TECHNICAL INFORMATION Revision.96 July 5 GENERAL DESCRIPTION The TAA8 is a 9W/ch continuous average two-channel
More informationTECHNICAL INFORMATION
Stereo 20W (4Ω) Class-T Digital Audio Amplifier using Digital Power Processing TM Technology TA2020-020 September, 2000 General Description The TA2020-020 is a 20W continuous average two-channel Class-T
More informationSupIRBuck TM IRDC3840W USER GUIDE FOR IR3840W EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM DESCRIPTION USER GUIDE FOR IR3840W EVALUATION BOARD The IR3840W is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 5mmx6mm Power QFN package.
More informationSupIRBuck TM IRDC3841W USER GUIDE FOR IR3841W EVALUATION BOARD DESCRIPTION BOARD FEATURES
IRDC384W SupIRBuck TM DESCRIPTION USER GUIDE FOR IR384W EVALUATION BOARD The IR384W is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 5mmx6mm Power
More information3W Stereo Class-D Audio Power Amplifier BA Data Sheet. Biforst Technology Inc. Rev.1.1,
3W Stereo Class-D Audio Power Amplifier BA20550 Data Sheet Rev.1.1, 2007.02.12 Biforst Technology Inc. 3W Stereo Class-D Audio Power Amplifier BA20550 GENERAL DESCRIPTION The BA20550 is a 5V class-d amplifier
More informationEvaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM2335
Evaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM2335 FEATURES Single-ended and differential input capability User-friendly interface connection Optimized EMI suppression filter assembled
More informationRB-TK2051 CLASS-T DIGITAL AUDIO AMPLIFIER 2 CHANNEL TK2051 EVALUATION BOARD GENERAL DESCRIPTION APPLICATIONS FEATURES BENEFITS
Tripath Technology, Inc. - Technical Information RB-TK05 CLASS-T DIGITAL AUDIO AMPLIFIER CHANNEL TK05 EVALUATION BOARD Technical Information- Board Rev..4 Revision.0 April 00 GENERAL DESCRIPTION The RB-TK05
More informationSupIRBuck TM IRDC3447-P0V9 USER GUIDE FOR IR3447 EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM USER GUIDE FOR IR3447 EVUATION BOARD DESCRIPTION IRDC3447-P0V9 The IR3447 is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 5mmx6mm QFN
More informationSupertex inc. HV748DB1 HV748 ±75V 1.25A Ultrasound Pulser Demoboard
HV78DB HV78 ±75V.5A Ultrasound Pulser Demoboard Introduction The HV78 is a monolithic -channel, high speed, high voltage, ultrasound transmitter pulser. This integrated, high performance circuit is in
More informationSTEREO CLASS-T AUDIO CONTROLLER USING DIGITAL POWER PROCESSING (DPP ) TECHNOLOGY
TC000 STEREO CLASS-T AUDIO CONTROLLER USING DIGITAL POWER PROCESSING (DPP ) TECHNOLOGY Technical Information Revision. December 003 GENERAL DESCPTION The TC000 is a two channel audio controller that uses
More informationSupIRBuck TM IRDC3846-P1V2 USER GUIDE FOR IRDC3846 EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM USER GUIDE FOR IRDC3846 EVUATION BOARD DESCRIPTION IRDC3846-PV2 The IR3846 is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 5mmx7mm QFN
More informationS U1 Configured for Filterless Output S U2 Configured for Filtered Output S Fully Assembled and Tested JU104, JU105, SHDN_1, TEMP_1
9-5477; Rev 0; 8/0 MAX98400A Evaluation Kit General Description The MAX98400A evaluation kit (EV kit) configures the MAX98400A Class D amplifier to drive x0w into a pair of 8I speakers in stereo mode,
More informationSupIRBuck TM IRDC3856 USER GUIDE FOR IR3856 EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM DESCRIPTION USER GUIDE FOR IR3856 EVALUATION BOARD The IR3856 is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 4mmx5mm Power QFN package.
More informationMini Evaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM2301-MINI
Mini Evaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM30-MINI FEATURES DC power supply accepts.5 V to 5.5 V Single-ended and differential input capability Extremely small board size allows
More informationEvaluation Board for 2 W, Filterless, Class-D Stereo Audio Amplifier EVAL-SSM2306
Evaluation Board for W, Filterless, Class-D Stereo Audio Amplifier EVAL-SSM06 FEATURES Highly configurable DIP switch settings: input configuration, coupling techniques, and shutdown control Optional dc
More informationTPA3123 Class-D Audio Amplifier Board User s Guide
*8W@4Ω TPA33 Class-D Audio Amplifier Board User s Guide 004-009 Sure Electronics Inc. AA-AB34_Ver.0 *8W @4Ω TPA33 CLASS-D AUDIO AMPLIFIER BOARD USER S GUIDE Table of Contents Chapter. Overview.... Overview....
More informationIRDC3822A. Rev /22/2008 1
02/22/2008 SupIRBuck TM DESCRIPTION USER GUIDE FOR IR3822A EVALUATION BOARD The IR3822A is a synchronous buck converter, providing a compact, high performance and flexible solution in a small 5mmx6mm Power
More informationReference Design EBC iw for 5V 1A Mini-TA Charger Design
Reference Design EBC10010 iw1700-01 for 5V 1A Mini-TA Charger Design Table of Contents iw1700-01 For Mini-TA Charger Design (AC Input 90 264V AC, Output 5V 1A) EBC10010 1.0. Introduction...3 2.0. Design
More informationEVQ4470-L-00A High-Efficiency, Fast-Transient, 5A, 36V Step-Down Converter Evaluation Board
EVQ4470-L-00A High-Efficiency, Fast-Transient, 5A, 36V Step-Down Converter Evaluation Board DESCRIPTION The EVQ4470-L-00A is an evaluation board for the MPQ4470, a high-efficiency step-down regulator with
More informationMPQ7731 5W - 30W Class D Mono Bridged Audio Amplifier Available in AEC-Q100
MPQ7731 5W - 30W Class D Mono Bridged Audio Amplifier Available in AEC-Q100 DESCRIPTION The MPQ7731 is a mono, 5W - 30W Class D Audio Amplifier. It is one of MPS second generation of fully integrated audio
More informationPAM8402. General Description. Key Features. Applications. Typical Application Vdd. 2 W Class-D Stereo Audio Amplifier with Enable
Key Features 2W@0 THD per Channel Output into a 4Ω oad at V Support Speakers or Earphones(4Ω to 32 Ω) ow THD+N Superior ow Noise without Input Efficiency up to 8 Short Circuit Protection Space Saving Package:
More informationAugust 2011 Rev FEATURES. Fig. 1: XRP7618 Evaluation Board Schematics
August 2011 Rev. 2.2.0 GENERAL DESCRIPTION The is an 8-channel, high voltage, constant-current sink LED driver capable of sinking up to 100mA current per channel. With outputs rated at 30V, the can control
More informationMP W Class D Mono Single Ended Audio Amplifer
The Future of Analog IC Technology MP772 2W Class D Mono Single Ended Audio Amplifer DESCRIPTION The MP772 is a mono 2W Class D Audio Amplifier. It is one of MPS second generation of fully integrated audio
More informationEvaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM2304
Evaluation Board for Filterless Class-D Audio Amplifier EVAL-SSM04 FEATURES Highly configurable DIP switch settings: input configuration, coupling methods, and shutdown control Optional dc power supply
More informationit2025j 30 khz to 18 GHz High-Gain Power Amplifier VCTRL2 VD2 OUT VG2 VG1 Description Features Device Diagram Recommended bias conditions:
30 khz to GHz High-Gain Power Amplifier Description Features The it2j is a RoHS-6-compliant packaged broadband GaAs MMIC traveling wave amplifier designed for medium output power applications where low-frequency
More informationAN3385 Application note
Application note 50 W + 50 W dual BTL class-d audio amplifier demonstration board based on the TDA7492 Introduction This application note describes the STEVAL-CCA027V1 demonstration board designed for
More informationESMT Preliminary AD52068
2x20W Stereo Class-D Audio Amplifier with Power Limit Features Single supply voltage 4.5V ~ 26V for loudspeaker driver Built-in LDO output 5V for others Loudspeaker power from 24V supply BTL Mode: 20W/CH
More informationRX-321 DSP Receiver. Ten-Tec, Inc 1185 Dolly Parton Parkway Sevierville, TN Copyright Ten-Tec Incorporated
RX-321 DSP Receiver Ten-Tec, Inc 1185 Dolly Parton Parkway Sevierville, TN 37862 Copyright Ten-Tec Incorporated Rx-321 Receiver The RX-321 receiver was deisgned by Ten-Tec for OEM applications. It was
More informationSupIRBuck TM IRDC3839 USER GUIDE FOR IR3839 EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM DESCRIPTION USER GUIDE FOR IR3839 EVALUATION BOARD The IR3839 SupIRBuck TM is an easy-to-use, fully integrated and highly efficient DC/DC regulator. The onboard PWM controller and MOSFETs
More informationAN3383 Application note
Application note STA350BW 2.0-channel demonstration board Introduction The purpose of this application note is to describe: how to connect the STA350BW 2.0-channel demonstration board how to evaluate the
More informationAN4199 Application note
Application note Two-layer demonstration board based on the STA333IS Introduction The board shown in Figure 1 is a two-layer demonstration board designed for the evaluation of the STA333IS two-channel,
More informationSUN MHz, 800mA Synchronous Step-Down Converter GENERAL DESCRIPTION EVALUATION BOARD APPLICATIONS. Typical Application
GENERAL DESCRIPTION The is a 1.5MHz constant frequency, slope compensated current mode PWM stepdown converter. The device integrates a main switch and a synchronous rectifier for high efficiency without
More informationLDS8710. High Efficiency 10 LED Driver With No External Schottky FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
High Efficiency 10 LED Driver With No External Schottky FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier*)
More informationReference Design for MHz Push-Pull 600 W RF Amplifier IXZ318N50L
1609 Oakridge Drive, Suite 100 Fort Collins, CO. 80525 (970) 493-1901 www.ixyscolorado.com Reference Design for 13.56 MHz Push-Pull 600 W RF Amplifier IXZ318N50L Martin Jones R&D/Application Engineering
More informationMP W Class D Mono Single Ended Audio Amplifer
The Future of Analog IC Technology MP772 2W Class D Mono Single Ended Audio Amplifer DESCRIPTION The MP772 is a mono 2W Class D Audio Amplifier. It is one of MPS second generation of fully integrated audio
More informationMP W Class D Mono Single Ended Audio Amplifier
The Future of Analog IC Technology MP7747 W Class D Mono Single Ended Audio Amplifier DESCRIPTION The MP7747 is a mono W Class D Audio Amplifier. It is one of MPS products of fully integrated audio amplifiers
More informationA MHz, 600mA S YNCHRONOUS STEP-DOWN CONVERTER. Thermal Resistance. Top View. Ordering Information. θ JC. θ JA. Part Number A7106E5-Adj
Description Features The is a 1.5MHz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without
More information1.5 MHz, 600mA Synchronous Step-Down Converter
GENERAL DESCRIPTION is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an
More informationMPM V, 1.5A Module, Synchronous, Step-Down Converter with an Integrated Inductor AEC-Q100 Qualified
The Future of Analog IC Technology DESCRIPTION The MPM3515 is a synchronous, rectified, stepdown converter with built-in power MOSFETs, inductors, and capacitors. The MPM3515 offers a very compact solution
More informationPreliminary T8300AD TE CH FEATURES GENERAL DESCRIPTION PART NUMBER EXAMPLES
PWM Control 1500mA Step-Down Converter Built-sensitive switch hysteresis control function FEATURES Wide Input Voltage Range: 4.5V to 30V LED Output Current Up to 1200mA Soft-start Single pin on/off and
More informationPAM8403H EVB User Guide
-EV Board User Guide AE Department 1. Revision Information PAM8403H Date Revision Description Comment 2008/03/24 V1.0 Initial Release 2012/07/31 V1.1 Update PCB 2. PAM8403H General Description The PAM8403H
More informationTS19371 Boost (Step-up) WLED Driver with OVP
SOT-26 Pin Definition: 1. SW 6. VIN 2. GND 5. OVP 3. FB 4. CTRL SOP-8 Pin Definition: 1. VIN 8. SW 2. GND 7. GND 3. GND 6. GND 4. CTRL 5. FB General Description The TS19371 is a step-up DC/DC converter
More informationTest Report. 10W/5V/2A AC/DC Adapter. Reference Design Using UCC28700
Test Report 0W/5V/2A AC/DC Adapter Reference Design Using UCC28700 Table of Content Introduction... 3 2 Electrical Performance Specifications... 3 3 Schematic... 4 4 Function Test Report... 5 4. Test Equipment...
More informationMSW2T /MSW2T SP2T Surface Mount High Power PIN Diode Switch
RELEASED MSW2T-2040-193/MSW2T-2041-193 SP2T Surface Mount High Power PIN Diode Switch Features: Wide Operating Frequency Band: 50 MHz to 4 GHz Surface Mount SP2T Switch: 5mm x 8mm x 2.5mm Industry Leading
More informationMP V, 5A Dual Channel Power Half-Bridge
The Future of Analog IC Technology MP8046 28V, 5A Dual Channel Power Half-Bridge DESCRIPTION The MP8046 is a configurable full-bridge or dual channel half-bridge that can be configured as the output stage
More informationMAX98355 Evaluation Kit Evaluates: MAX98355A/MAX98355B
19-6407; Rev 0; 7/12 MAX98355 Evaluation Kit General Description The MAX98355 evaluation kit (EV kit) is a fully assembled and tested PCB that evaluates the MAX98355 PCM digital input Class D power amplifier.
More informationEvaluation Board for ADP2114 EVAL-ADP2114
Evaluation Board for ADP EVAL-ADP FEATURES Full-featured demo board for the ADP Standalone capability Configurable dual synchronous step-down, dc-to-dc switching regulator Dual A/ A or A/ A output or single
More informationDocumentation. DDS Signal Generator DH5YM. April 8, Document information
Documentation DDS Signal Generator April 8, 2009 Document information Info Keywords Abstract Content AD9832, DDS, signal generator This document describes a small signal generator with either AD9832 or
More informationTGA2602-SM MHz High IP3 Dual phemt. Key Features and Performance. Measured Performance. Primary Applications. Product Description
800-3000 MHz High IP3 Dual phemt Key Features and Performance 800-3000 MHz Frequency Range
More informationEV2635A-R-00A Fully Power Management Charger For Single-Cell Battery System
The Future of Analog IC Technology EV2635A-R-00A Fully Power Management Charger For Single-Cell Battery System DESCRIPTION The EV2635A-R-00A, the evaluation Board is designed to demonstrate the capabilities
More informationGallium Nitride MMIC Power Amplifier
Gallium Nitride MMIC Power Amplifier August 2015 Rev 4 DESCRIPTION AMCOM s is an ultra-broadband GaN MMIC power amplifier. It has 21dB gain, and >41dBm output power over the 0.03 to 6GHz band. This MMIC
More informationPAM8803 Class-D Audio Amplifier Board User s Guide
*W @4Ω PAM8803 Class-D Audio Amplifier Board User s Guide 004-009 Sure Electronics Inc. AA-AB33&AA-AB333_Ver.0 *W @4Ω PAM8803 CLASS-D AUDIO AMPLIFIER BOARD USER S GUIDE Table of Contents Chapter. Overview....
More informationPowering High Speed Analog-to-Digital Converters with Switching Power Supplies
Powering High Speed Analog-to-Digital Converters with Switching Power Supplies By Michael Cobb, Senior Applications Engineer, High Speed Converter Group, Analog Devices Reprinted with Permission from Power
More informationSPECIFICATIONS: Subcarrier Frequency 5.5MHz adjustable, FM Modulated +/- 50KHz. 2nd 11MHz >40dB down from 5.5MHz
Mini-kits AUDIO / SUBCARRIER KIT EME75 Version4 SPECIFICATIONS: Subcarrier Frequency 5.5MHz adjustable, FM Modulated +/- 50KHz Subcarrier Output 1.5v p-p Output @ 5.5MHz DESCRIPTION & FEATURES: The Notes
More informationT8308 TE CH FEATURES GENERAL DESCRIPTION. Applications LED/Display Back Light Driver Lightings Portable Communication Devices Handheld Electronics
PWM Control 800mA Step-Down Converter FEATURES Wide Input Voltage Range: 7V to 30V LED Output Current Up to 800mA Soft-start Single pin on/off and brightness control using DC voltage or PWM High efficiency
More informationPAM8406 EVB User Guide
EV Board User Guide AE Department. Revision Information PAM8406 Date Revision Description Comment 0//5 V.0 Initial Release. EV Board Schematic J5 + C C R C6 R C7 C FB FB C0 SP J4 C5 VREF 8 INL 7 6 MUTE
More informationFigure 1. Block Diagram
All-Digital High Efficiency Power Amplifier FEATURES HIGH OUTPUT CAPABILITY 2 x 30W into 8Ω or 1 x 60W into 4 Ω @ 88%
More informationEZ6301QI Triple Output Module
Evaluation board user guide enpirion power solutions EZ6301QI Triple Output Module 1.5A DC-DC Buck Module with 2 x 300mA LDOs EVALUATION BOARD OVERVIEW 3 2 2 1 1 2 2 3 6 5 5 1 7 5 8 2 2 3 4 Figure 1: Evaluation
More informationTHE PHYSICAL MAP GENERAL DESCRIPTION APPLICATIONS BLOCK DIAGRAM FEATURES SHENZHEN XPTEK TECHNOLOGY CO., LTD
GENERAL DESCRIPTION SHENZHEN XPTEK TECHNOLOGY CO., LTD The is an audio power amplifier primarily designed for demanding applications in low-power portable systems. It is capable of delivering 5 watts of
More informationEvaluation Board for the AD8333 I/Q Demodulator AD8333-EVALZ
Evaluation Board for the AD333 I/Q Demodulator AD333-EVALZ FEATURES Factory tested and ready to use SMA input and output connectors (7) Configurable jumpers for user options Phase select Provision for
More informationFilterless 3W Class- D Mono Audio Amplifier
Preliminary Datasheet LPA00 Filterless 3W Class- D Mono Audio Amplifier General Description The LPA00 is a 3W, class-d audio amplifier. It offers low THD+N, allowing it to achieve high-quality Power Supply
More informationOBSOLETE. 2 W Filterless Class-D Stereo Audio Amplifier SSM2304 FEATURES APPLICATIONS GENERAL DESCRIPTION FUNCTIONAL BLOCK DIAGRAM
FEATURES Filterless Class-D amplifier with built-in output stage W into 4 Ω and.4 W into 8 Ω at 5. V supply with
More informationHX1151 GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. Step-Down Converter. 1.5MHz, 1.3A Synchronous
1.5MHz, 1.3A Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 1.5MHz Constant Frequency Operation 1300mA Output Current No Schottky Diode Required 2.3 to 6 Input oltage Range Adjustable
More informationHM V~5V Input 12W Output Step-up DC/DC Converter GENERAL DESCRIPTION FEATURES APPLICATIONS
3.3V~5V Input 12W Output Step-up DC/DC Converter GENERAL DESCRIPTION The HM9226 is a high frequency, high efficiency DC to DC converter with an integrated 6A, 40mÙ power switch capable of providing an
More information15V Stereo Class-D Audio Power Amplifier. Description. Tracking Code Date Code
15V Stereo Class-D Audio Power Amplifier Features Operate from 8~15V supply voltage Class-D power 15W/ch into 8Ω from 15V supply @ 10% THD+N for stereo 12W/ch into 6Ω from 12V supply @ 10% THD+N for stereo
More informationDT V 1A Output 400KHz Boost DC-DC Converter FEATURES GENERAL DESCRIPTION APPLICATIONS ORDER INFORMATION
GENERAL DESCRIPTION The DT9111 is a 5V in 12V 1A Out step-up DC/DC converter The DT9111 incorporates a 30V 6A N-channel MOSFET with low 60mΩ RDSON. The externally adjustable peak inductor current limit
More informationATF-501P8. Application Note MHz High Linearity Amplifier
ATF-501P8 450 MHz High Linearity Amplifier Application Note 5058 ATF-501P8 Applications Information Description Avago Technologies ATF-501P8 is an enhancement mode PHEMT designed for high linearity and
More informationFigure 1 Schematic. Quantity Ref.Des Description Number
1 Schematic Figure 1 Schematic. 2 Bill of Materials Numbe r Quantity Ref.Des Description Mfg Part Number 1 1 BR1 800 V, 1 A, Bridge Rectifier, SMD, DFS DF08S Diodes Inc 2 1 C1 100 nf, 275VAC, Film, X2
More informationCM8685 5W MONO CLASS D PLUS TM AUDIO AMPLIFIER
GENERAL DESCRIPTION The CM5/G is a single channel monolithic Class D Plus TM Audio Amplifier IC that using Champion s unique close loop and feed forward compensation techniques to achieve better THD+N.
More informationApplying the DDX-8000 in Binary Mode
Applying the DDX-000 in Binary Mode For Applications Assistance Contact: Apogee Technical Support e-mail: support@apogeeddx.com 9 Morgan Drive, Norwood, MA 0 voice: (7) 55-950 fax: (7) 0-95 email: apogee@apogeeddx.com
More informationTAT7469 CATV 75 Ω phemt Dual RF Amplifier
Applications Edge QAM Gain Stage MDU Output RF Distribution Amplifiers Low Noise Optical TIA SOIC-8 Package Product Features Functional Block Diagram 75 Ω, 50 MHz to 1200 MHz Bandwidth RF Low Noise Figure:
More informationeorex EP MHz, 600mA Synchronous Step-down Converter
1.5MHz, 600mA Synchronous Step-down Converter Features High Efficiency: Up to 96% 1.5MHz Constant Switching Frequency 600mA Output Current at V IN = 3V Integrated Main Switch and Synchronous Rectifier
More informationPhotolink- Fiber Optic Receiver PLR135
Features High PD sensitivity optimized for red light Data : NRZ signal Low power consumption for extended battery life Built-in threshold control for improved noise Margin The product itself will remain
More informationTAT7457-EB. CATV 75 Ω phemt Adjustable Gain RF Amplifier. Applications. Ordering Information
Applications Single-ended and Push-pull Optical Receivers Low-noise Drop Amplifiers Distribution Amplifiers Multi-Dwelling Units Single-ended Gain Block SOT-89 package Product Features Functional Block
More informationTAT Ω 5V MHz RF Amplifier
TAT74 Datasheet: Rev D 04-17-17-1 of 8 - Disclaimer: Subject to change without notice TAT74 Absolute Maximum Ratings Parameter Rating Storage Temperature - to 1 C Device Voltage (VDD) +10 V Operation of
More informationShenZhen Nsiway Technology Co., Ltd 2013/08. Nsiway 1
NS4215 Data Sheet V1.0 ShenZhen Nsiway Technology Co., Ltd 2013/08 Nsiway 1 Change History DATA VERSION AUTHOR CHAGE EXPLAIN Nsiway 2 CONTENTS CHANGE HISTORY... 2 GENERAL DESCRIPTION... 5 FEATURES... 5
More informationSupIRBuck TM IRDC3710-DF USER GUIDE FOR IRDC3710-DF EVALUATION BOARD DESCRIPTION BOARD FEATURES
SupIRBuck TM IRDC3710-DF USER GUIDE FOR IRDC3710-DF EVALUATION BOARD DESCRIPTION The IR3710M is single phase sync-buck PWM controller IC optimized for efficiency in high performance portable electronics.
More informationEV-167 EVALUATION BOARD DATASHEET. AAT5101 EVAL: 2.5W Mono Class D Audio Power Amplifier. Introduction. Board Picture
Introduction EVALUATION BOARD DATASHEET The AAT5 is a high efficiency mono filter-free Class D audio power amplifier with fully differential architecture and BTL (Bridge Tied Load) output. The AAT5 evaluation
More informationHX1103 HX1103.
HX1103 Synchronous Buck DC/DC Converter Features Up to 94% Efficiency Current Mode Operation for Excellent Line and Load Transient Response Low Quiescent Current: 200µA Up to 800mA Load Current Soft-start
More informationReference Design EBC894. Dimmable LED Driver with iw3602 (AC Input 90V 135V AC. , Output 3 LEDs)
Reference Design Dimmable LED Driver with iw3602 (AC Input 90V 135V AC Table of Contents Dimmable LED Driver with iw3602 1.0. Introduction...3 2.0. Design Features...3 3.0. Schematic...4 4.0. PCB Layout...
More informationA8160A. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION
DESCRIPTION The is a step-up DC-DC converter specifically designed for driving white LEDs with a constant current. The internal MOSFET can support up to 10 White LEDs for backlighting and OLED power application,
More informationTAT Ω phemt Adjustable Gain RF Amplifier
Applications Single-ended and Push-pull Optical Receivers Low-noise Drop Amplifiers Distribution Amplifiers Multi-Dwelling Units Single-ended Gain Block Product Features Gain, return loss and bias externally
More informationSTEREO 50W (8Ω) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP ) TECHNOLOGY
TK050 STEREO 50W (8Ω) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP ) TECHNOLOGY Technical Information Revision.3 July 004 GENERAL DESCRIPTION The TK050 (TC000/TP050 chipset)
More informationWhite LED Step-Up Converter
FEATURES Inherently Matched LED Current Drives Up to 27 LEDs from a 5V Supply Power Management IC 36V Rugged Bipolar Switch Fast 1.2MHz Switching Frequency Vovp(MAX) = 29V Moisture Sensitivity Level 3
More informationQPD W, 50V, DC 3.7 GHz, GaN RF Transistor
General Description The is a 65 W (P3dB) wideband unmatched discrete GaN on SiC HEMT which operates from DC to 3.7 GHz and a V supply rail. The device is in an industry standard air cavity package and
More informationEN6363QI 6A PowerSoC. Evaluation board user guide enpirion power solutions. Step-Down DC-DC Switching Converter with Integrated Inductor
Evaluation board user guide enpirion power solutions EN6363QI 6A PowerSoC Step-Down DC-DC Switching Converter with Integrated Inductor EVALUATION BOARD OVERVIEW 1 2 3 8 4 7 9 5 6 Figure 1: Evaluation Board
More informationMIX3001 2X3W FM Non-Interference Class-D Amplifier. Features. Description. Applications
Description The MIX3001 is a high efficiency, 3/channel stereo class-d audio power amplifier. A Low noise, filterless architecture eliminates the out filter, it required few external components for operation
More informationHigh Efficiency 1MHz, Step up Regulator
General Description Features The is the high power and high efficiency boost converter with an integrated 30V FET ideal for LCD panel backlighting applications. 30V output voltage allows for 8 high power
More informationTGA2601-SM MHz High IP3 Dual phemt. Key Features and Performance. Measured Performance. Primary Applications. Product Description
800-3000 MHz High IP3 Dual phemt Key Features and Performance 800-3000 MHz Frequency Range
More informationPAM2841EV1 User Guide 1.5A SW CURRENT, 40V PRECISION WLED DRIVER
General Description The PAM2841 is a step-up current mode LED Driver. The PAM2841 supports a range of input voltages from 2.5V to 5.5V, allowing the use of a single Li+/Li- polymer cell, 3AA cell battery,
More informationRF3826TR13. 9W GaN Wide-Band Power Amplifier 30MHz to 2500MHz. Features. Applications. Ordering Information RF3826
9W GaN Wide-Band Power Amplifier 30MHz to 2500MHz The RF3826 is a wideband Power Amplifier designed for CW and pulsed applications such as wireless infrastructure, RADAR, two way radios, and general purpose
More informationW-6237EVAL2 EVALUATION BOARD FOR W-6237 HIGH VOLTAGE WHITE LED DRIVER
APPLICATION NOTE AN24 W-6237EVAL2 EVALUATION BOARD FOR W-6237 HIGH VOLTAGE WHITE LED DRIVER Denisa Stefan, Applications Engineer INTRODUCTION This document describes the W-6237EVAL2 Evaluation Board for
More informationMPM3510A. 36V/1.2A Module Synchronous Step-Down Converter with Integrated Inductor DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
The Future of Analog IC Technology MPM351A 36V/1.2A Module Synchronous Step-Down Converter with Integrated Inductor DESCRIPTION The MPM351A is a synchronous, rectified, step-down converter with built-in
More informationMT3420 Rev.V1.2 GENERAL DESCRIPTION FEATURES APPLICATIONS. 1.4MHz, 2A Synchronous Step-Down Converter
1.4MHz, 2A Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 1.4MHz Constant Frequency Operation 2A Output Current No Schottky Diode Required 2.5V to 5.5V Input Voltage Range Output Voltage
More informationPRELIMINARY. Parameter 500 MHz 1.0 GHz 1.5 GHz 2.0 GHz 2.5 GHz Units. Small Signal Gain db
CGH49PP 9 W, RF Power GaN HEMT PRELIMINARY Cree s CGH49PP is an unmatched, gallium nitride (GaN) high electron mobility transistor (HEMT). The CGH49PP, operating from a 28 volt rail, offers a general purpose,
More informationAN4200 Application note
Application note Four-layer demonstration board based on the STA333IS Introduction The STEVAL-CCA053V1 is a four-layer demonstration board designed for the evaluation of the STA333IS two-channel, high-efficiency
More information