Thick Film Resistor Networks Military, MIL-PRF Qualified, Type RZ, Single-In-Line, Molded SIP; 01, 03, 05 Schematics

Transcription

1 STNDRD ELECTRICL SPECIFICTIONS VISHY DLE RESISTOR MODEL/ PIN NO/ SCHEMTIC POWER RTING MX. at 70 C PROFILE W W PCKGE POWER RTING MX. at 70 C FETURES MIL-PRF-834 qualified 0.195" [4.95 mm] and 0.350" [8.89 mm] C maximum seated heights Thick film resistive elements TCR available in K (± 100 ppm/ C) or M (± 300 ppm/ C) characteristic ll device leads are hot-solder dipped Rugged molded case construction Compatible with automatic insertion equipment 100 % screen tested per Group, Subgroup 1 of MIL-PRF-834 ll devices are capable of passing the MIL-STD-202, Method 210, Condition D Resistance to Soldering Heat test vailable in tube pack RNGE Ω STNDRD TOLERNCE (1) % Notes (1) ± 1 % and ± 5 % available (2) K = ± 100 ppm/ C; M = ± 300 ppm/ C GLOL PRT NUMER INFORMTION TEMPERTURE COEFFICIENT (2) (- 55 C to C) Consult factory ± 2 K, M Consult factory ± 2 K, M New Global Part Numbering: M83407K10GCD (preferred part numbering format) M K G C D 0 3 MIL STYLE SPEC SHEET CHRCTERISTIC VLUE TOLERNCE SCHEMTIC PCKGING M = 6 Pin, K = 100 ppm 3 digit significant F = ± 1 % C = ussed D = Tin/Lead, Tube = 8 Pin, M = 300 ppm figure, followed by G = ± 2 % G = Isolated DSL = Tin/Lead, Tube, 06 = 10 Pin, a multiplier J = ± 5 % Single Lot Date Code 07 = 6 Pin, Profile 10R0 = 10 Ω 08 = 8 Pin, Profile 3302 = 33 k Ω 09 = 10 Pin, Profile 1004 = 1 M Ω Historical Part Number example: M83407K10GC (will continue to be accepted) M K 10 G C D MIL STYLE SPEC SHEET CHRCTERISTIC VLUE TOLERNCE SCHEMTIC PCKGING New Global Part Numbering: M83404K0GHD (preferred part numbering format) M K G H D 0 3 MIL STYLE SPEC SHEET CHRCTERISTIC VLUE TOLERNCE SCHEMTIC PCKGING M = 6 Pin, K = 100 ppm Per std. Mil. Spec F = ± 1 % H = Dual D = Tin/Lead, Tube = 8 Pin, M = 300 ppm (see Impedence G = ± 2 % Terminator DSL = Tin/Lead, Tube, 06 = 10 Pin, Codes table) J = ± 5 % Single Lot Date Code 07 = 6 Pin, Profile 08 = 8 Pin, Profile 09 = 10 Pin, Profile Historical Part Number example: M83404K0GH (will continue to be accepted) M K 0 G H D MIL STYLE SPEC SHEET CHRCTERISTIC VLUE TOLERNCE SCHEMTIC PCKGING WEIGHT g For technical questions, contact: ff2aresistors@vishay.com Document Number: Revision: 25-Jul-08

2 DIMENSIONS in inches [millimeters] "" Profile [ [ ± ± 0.0 [2.54 ± 7] Non-ccumulative Pin # 1 [32 ± 0.102] C Equal Space [ [ "C" Profile [ [ ± 0.0 [2.54 ± 7] Non-ccumulative Pin # 1 ± [32 ± 0.102] C Equals Spaces [ [ max. [2.49 max.] 0.2 ± [0.3 ± 0.102] VISHY DLE MODEL MSM06 MSM08 MSM10 83 ± [14.81 ± 0.381] 83 ± [19.89 ± 0.381] 83 ± [24.97 ± 0.381] 00 [12.70] 00 [17.78] 00 [22.86] C max. [2.49 max.] 0.2 ± [0.3 ± 0.102] TECHNICL SPECIFICTIONS PRMETER UNIT MSM SERIES Maximum Operating Voltage V DC 50 Voltage Coefficient of Resistance V eff < 50 ppm Dielectric Strength V C 200 min. Insulation Resistance Ω M Operating Temperature Range C - 55 to Storage Temperature Range C - 55 to MECHNICL SPECIFICTIONS ody: Molded epoxy Terminals: Copper alloy, hot-solder dipped Solderability: Per MIL-PRF-834 CGE CODE: and SH9 MILITRY IMPEDNCE CODES CODE R 1 (Ω) R 2 (Ω) CODE R 1 (Ω) R 2 (Ω) K 3.3K K 6.2K K K Document Number: For technical questions, contact: ff2aresistors@vishay.com Revision: 25-Jul-08 2

3 DERTING Schematic Profile Package Package Package 1.40 Package Package Package mbient Temperature C Schematic Profile mbient Temperature C 8 Package Package 0.80 Packag e Package Package 0.36 Package Schematic Profile mbient Temperature C mbient Temperature C Package Package 1.32 Package Package Package 0.88 Package mbient Temperature C mbient Temperature C For technical questions, contact: ff2aresistors@vishay.com Document Number: Revision: 25-Jul-08

4 CIRCUIT PPLICTIONS Schematic 5, 7 or 9 resistors with one pin common Profile (M83407xxxxxxC) (M83404xxxxxxC) (M83408xxxxxxC) (M834xxxxxxC) (M83409xxxxxxC) (M83406xxxxxxC) n-1 n The,,,, and molded single-in-line resistor networks provide the user with a choice of 5, 7 or 9 nominally equal resistors, each connected to a common pin (Pin No. 1). Commonly used in the following applications: Wired OR Pull-up Open Collector Pull-up Power Gate Pull-up TTL Input Pull-down MOS/ROM Pull-up/Pull-down TTL Unused Gate Pull-up Schematic 3, 4 or 5 isolated resistors Schematic n-1 n n-1 n R 2 R 1 Profile (M83407xxxxxxG) (M83404xxxxxxG) (M83408xxxxxxG) (M834xxxxxxG) (M83409xxxxxxG) (M83406xxxxxxG) The,,,, and molded single-in-line resistor networks provide the user with a choice of 3, 4 or 5 nominally equal resistors. Each resistor is isolated from all others. Commonly used in the following applications: Wired OR Pull-up Long-Line Impedance alance Power Driven Pull-up LED Current Limiting Power Gate Pull-up ECL Output Pull-down Line Termination TTL Input Pull-down 4, 6 or 8 isolated resistors Profile (M83407xxxxxxH) (M83404xxxxxxH) (M83408xxxxxxH) (M834xxxxxxH) (M83409xxxxxxH) (M83406xxxxxxH) The,,,, and molded single-in-line resistor networks provide the user with a choice of 4, 6 or 8 pair of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. PERFORMNCE TEST CONDITIONS MX. ΔR (Typical Test Lots) Power Conditioning 1.5 x rated power, applied 1.5 h ON and h OFF for 100 h ± 4 h at + 25 C ambient temperature ± 0 % ΔR Thermal Shock 5 cycles between - 65 C and C ± 0 % ΔR Short Time Overload 2.5 x rated working voltage for 5 s ± 0.25 % ΔR (Characteristic K) ± 0 % ΔR (Characteristic M) Low Temperature Operation 45 min at full rated working voltage at - 65 C ± 0.25 % ΔR (Characteristic K) ± 0 % ΔR (Characteristic M) Moisture Resistance 240 h with humidity ranging from 80 % RH to 98 % RH ± 0 % ΔR Resistance to Soldering Heat Leads immersed in C solder to within 1/16" of body for 10 s ± 0.25 % ΔR Shock Total of 18 shocks at 100 G's ± 0.25 % ΔR Vibration 12 h at maximum of 20 G's between 10 and 2000 Hz ± 0.25 % ΔR Load Life 1000 h at + 70 C, rated power applied 1.5 h ON, h OFF for full 1000 h period ± 0 % ΔR (Characteristic K) ± 2.00 % ΔR (Characteristic M) Terminal Strength 4 1/2 pound pull for 30 s ± 0.25 % ΔR Insulation Resistance MΩ (minimum) - Dielectric Withstanding No evidence of arcing or damage (200 V RMS for 1 min) - Document Number: For technical questions, contact: ff2aresistors@vishay.com Revision: 25-Jul-08 4

5 Legal Disclaimer Notice Vishay Disclaimer ll product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: Revision: 18-Jul-08 1