SVENSK STANDARD SS-EN ISO

Size: px

Start display at page:

Download "SVENSK STANDARD SS-EN ISO"

Blanche Chambers
5 years ago
Views:

SVENSK STANDARD SS-EN ISO 8321-2 Handläggande organ Fastställd Utgåva Sida Hälso- och sjukvårdsstandardiseringen, HSS 2000-06-30 1 1 (1+12) Copyright SIS.

1 SVENSK STANDARD SS-EN ISO Handläggande organ Fastställd Utgåva Sida Hälso- och sjukvårdsstandardiseringen, HSS (1+12) Copyright SIS. Reproduction in any form without permission is prohibited. Ophthalmic optics Specifications for material, optical and dimensional properties of contact lenses Part 2: Single-vision hydrogel lenses (ISO :2000) Ögonoptik Grundkrav för material, optiska egenskaper och dimensioner hos kontaktlinser Del 2: Enstyrke, mjuka (hydrogel-) linser (ISO :2000) The European Standard has the status of a Swedish Standard. This document contains the official English version of. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, STOCKHOLM Telefon: Telefax: E-post: sis.sales@sis.se. Internet: Upplysningar om sakinnehållet i standarden lämnas av HSS. Telefon: Telefax: E-post: hss@hss.se Prisgrupp N Tryckt i september 2000

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO March 2000 ICS English version Opthalmic optics - Specifications for material, optical and dimensional properties of contact lenses - Part 2: Single-vision hydrogel lenses (ISO :2000) Optique ophtalmique - Spécifications des propriétés des matériaux et des propriétés optiques et dimensionelles des lentilles de contact - Partie 2: Lentilles de contact en hydrogel unifocales (ISO :2000) Augenoptik - Grundanforderungen an Materialeigenschaften, optische Eigenschaften und Maße von Kontaktlinsen - Teil 2: Einstärken-Hydrogelkontaklinsen (ISO :2000) This European Standard was approved by CEN on 1 March CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. E

4 Page 2 Provläsningsexemplar / Preview Contents Page Foreword Scope Normative references Terms and definitions Requirements for dimensions and optical properties Test methods Conditioning of contact lenses prior to testing Tolerances Requirement for finish Criteria Inclusions and surface finish... 5 Annex A (informative) Recommended method for presenting the specifications of single-vision hydrogel contact lenses... 8 Bibliography Annex ZA (normative) Normative references to international publications with their corresponding European publications Annex ZB (informative) A-deviations... 12

5 Page 3 Foreword The text of the International Standard ISO :2000 has been prepared by Technical Committee ISO/TC 172 Optics and optical instruments in collaboration with Technical Committee CEN/TC 170 Ophthalmic optics, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2000, and conflicting national standards shall be withdrawn at the latest by September According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN ISO 8321 consists of the following parts, under the general title Ophthalmic optics - Specifications for material, optical and dimensional properties of contact lenses: - Part 1: Rigid corneal and scleral contact lenses - Part 2: Single-vision hydrogel contact lenses Annex A of this part of EN ISO 8321 is for information only. Endorsement notice The text of the International Standard ISO :2000 was approved by CEN as a European Standard without any modification. NOTE: Normative references to International Standards are listed in Annex ZA (normative). A-deviations are given in Annex ZB (informative).

6 Page 4 Provläsningsexemplar / Preview Ophthalmic optics Specifications for material, optical and dimensional properties of contact lenses Part 2: Single-vision hydrogel contact lenses 1 Scope This part of ISO 8321 specifies requirements for hydrated single-vision hydrogel contact lenses including tolerance limits for material, optical and dimensional properties. A method for presenting the specification of contact lenses is described in annex A. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 8321 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO : 1, Contact lenses and contact lens care products Vocabulary Part 1: Contact lenses. ISO 8599:1994, Optics and optical instruments Contact lenses Determination of the spectral and luminous transmittance. ISO :1999, Contact lenses Determination of back vertex power Part 1: Method using focimeter with manual focusing. ISO 9338:1996, Optics and optical instruments Contact lenses Determination of the diameters. ISO :1998, Optics and optical instruments Contact lenses Determination of thickness Part 2: Hydrogel contact lenses. ISO :1996, Optics and optical instruments Contact lenses Part 1: Determination of oxygen permeability and transmissibility with the FATT method. ISO 9914:1995, Optics and optical instruments Contact lenses Determination of refractive index of contact lens materials. ISO 10338:1996, Optics and optical instruments Contact lenses Determination of curvature. ISO 10339:1997, Ophthalmic optics Contact lenses Determination of water content of hydrogel lenses. ISO 10344:1996, Optics and optical instruments Contact lenses Saline solution for contact lens testing. 1 To be published. (Revision of ISO 8320:1986)

7 Page 5 3 Terms and definitions For the purposes of this part of ISO 8321, the terms and definitions given in ISO apply. 4 Requirements for dimensions and optical properties 4.1 Test methods Each dimension and physical or optical property specified shall be determined using a test method with a measurement tolerance limit better than one-half of the tolerance limit specified for the property. The International Standards which specify the relevant test methods are listed in Tables 1 and Conditioning of contact lenses prior to testing Contact lenses shall be conditioned in accordance with the relevant test method. 4.3 Tolerances When tested as described in 4.1 and 4.2 the dimensional and optical properties shall be as specified, within the appropriate tolerance limits given in Table 1 and the material physical properties as given in Table 2. 5 Requirement for finish 5.1 Criteria Acceptance and failure criteria for inclusions, surface imperfections, edge contour and finish shall be documented by the manufacturer. 5.2 Inclusions and surface finish When examined at 10 magnification in standard saline solution according to ISO 10344, the contact lens shall not exhibit any inclusions or surface imperfections which could interfere with its intended functional use. 5.3 Edge contour and finish When examined at 7 magnification, the contact lens edge shall meet the quality characteristics indicated by the manufacturer with respect to shape, smoothness and polish.

8 Page 6 Provläsningsexemplar / Preview Table 1 Dimensional and optical tolerances Property Tolerance limits Relevant International Standard Back optic zone radius ab 0,20 mm ISO Sagitta at specified diameter a 0,05 mm ISO Total diameter 0,20 mm ISO 9338 Optic zone diameter 0,20 mm ISO 9338 Centre thickness u 0,10 mm >0,10mm Back vertex power F v u 10 D 10 D < F v u 20 D F v >20D Prismatic error d F v u 6D F v >6D Specified optical prism e F v u 6D F v >6D Direction of specified optical prism Cylinder power F c u 2D 2D< F c u 4D F c >4D 0,010 mm + 0,10 t c c 0,015 mm + 0,05 t c c 0,25 D 0,50 D 1,00 D 0,25 cm/m 0,50 cm/m 0,25 cm/m 0,50 cm/m 5 0,25 D 0,37 D 0,50 D ISO ISO ISO ISO Direction of cylinder axis 5 a Tolerance is applicable when this property is the one specified by the manufacturer as the expression of the back surface curvature. b Tolerance is applicable when the step between successive back optic zone radii is 0,40 mm or greater. For smaller steps the tolerance is equal to half the design step (e.g. back optic zone radius design step 0,30 mm, tolerance 0,15 mm). c d e Examples of tolerance calculations: Nominal thickness Tolerance 0,035 mm 0,010+0,004 = 0,014 mm 0,070 mm 0,010+0,007 = 0,017 mm 0,150 mm 0,015+0,008 = 0,023 mm 0,300 mm 0,015+0,015 = 0,03 mm Prismatic error is measured at the geometrical centre of the optical zone. The reference for the prismatic direction in toric lenses is the basic axis on apex.

SVENSK STANDARD SS-EN ISO 15253

SVENSK STANDARD SS-EN ISO 15253 Fastställd Utgåva Sida 2001-05-04 1 1 (1+27) Copyright SIS. Reproduction in any form without permission is prohibited. Ophthalmic optics and instruments Optical devices