Färg och lack Bestämning av härdighet mot filiformkorrosion Del 1: Stålunderlag (ISO :2000)

Size: px

Start display at page:

Download "Färg och lack Bestämning av härdighet mot filiformkorrosion Del 1: Stålunderlag (ISO :2000)"

Lionel Harrison
5 years ago
Views:

SVENSK STANDARD SS-EN ISO 4623-1 Fastställd 2002-07-05 Utgåva 1 Färg och lack Bestämning av härdighet mot filiformkorrosion Del 1: Stålunderlag (ISO 4623-1:2000) Paints and varnishes Determination of

1 SVENSK STANDARD SS-EN ISO Fastställd Utgåva 1 Färg och lack Bestämning av härdighet mot filiformkorrosion Del 1: Stålunderlag (ISO :2000) Paints and varnishes Determination of resistance to filiform corrosion Part 1: Steel substrates (ISO :2000) ICS Språk: engelska Tryckt i september 2002 Copyright SIS. Reproduction in any form without permission is prohibited.

2 Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av. Standarden ersätter SS-EN ISO 4623, utgåva 1 och SS-ISO 4623, utgåva 1. The European Standard has the status of a Swedish Standard. This document contains the official English version of. This standard supersedes the Swedish Standards SS-EN ISO 4623, edition 1 and SS-ISO 4623, edition 1. Dokumentet består av 14 sidor. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, tel Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, STOCKHOLM Telefon: Telefax: E-post: sis.sales@sis.se. Internet:

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO January 2002 ICS Supersedes EN ISO 4623:1995 English version Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel substrates (ISO :2000) Peintures et vernis - Détermination de la résistance à la corrosion filiforme - Partie 1: Subjectiles en acier (ISO :2000) Beschichtungsstoffe - Bestimmung der Beständigkeit gegen Filiformkorrosion - Teil 1: Stahl als Substrat (ISO :2000) This European Standard was approved by CEN on 27 December CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. E

4 Page 2 Contents Page Foreword... 3 Introduction Scope Normative references Term and definition Principle Required supplementary information Sampling Apparatus Reagents Test panels Procedure Evaluation of the degree of filiform corrosion Precision Test report... 9 Annexes A Required supplementary information B Guidance notes on maintaining exposure conditions using saturated ammonium sulfate solution Annex ZA (normative)... 12

5 Page 3 Foreword The text of the International Standard from Technical Committee ISO/TC 35 "Paints and varnishes" of the International Organization for Standardization (ISO) has been taken over as a European Standard by Technical Committee CEN/TC 139 "Paints and varnishes", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2002, and conflicting national standards shall be withdrawn at the latest by July This document supersedes EN ISO 4623:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO :2000 has been approved by CEN as a European Standard without any modifications. NOTE Normative references to International Standards are listed in annex ZA (normative).

6 Page 4 Introduction A scribed mark cut through a coating of paints or varnishes on steel can give rise to filiform corrosion. This corrosion tends to develop when the relative humidity is high and when traces of salts are present either under the paint coating or at breaks in the coating. A certain amount of under-rusting of the substrate, starting from the scribed mark, will always occur. Filiform corrosion, however, is considered to be present only if the typical pattern in the form of threads is obvious.

7 Page 5 Paints and varnishes Determination of resistance to filiform corrosion Part 1: Steel substrates 1 Scope This part of ISO 4623 is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It describes a test procedure for assessing the protective action of coatings of paints or varnishes on steel against filiform corrosion arising from a scribed mark cut through the coating. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 4623 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 483, Plastics Small enclosures for conditioning and testing using aqueous solutions to maintain relative humidity at constant value. ISO 1513, Paints and varnishes Examination and preparation of samples for testing. ISO 1514, Paints and varnishes Standard panels for testing. ISO 2409, Paints and varnishes Cross-cut test. ISO 2808, Paints and varnishes Determination of film thickness. ISO 3270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and testing. ISO 3696, Water for analytical laboratory use Specification and test methods. ISO , Paints and varnishes Evaluation of degradation of coatings Part 10: Designation of intensity, quantity and size of common types of defect. ISO 7253, Paints and varnishes Determination of resistance to neutral salt spray (fog). ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling.

8 Page 6 3 Term and definition For the purposes of this part of ISO 4623, the following term and definition apply. 3.1 filiform corrosion a type of corrosion proceeding under a coat of paint, varnish or related product, in the form of threads, generally starting from bare edges or from local damage to the coating NOTE 1 Usually the threads are irregular in length and direction of growth, but they may also be nearly parallel and of approximately equal length. NOTE 2 Filiform corrosion can also occur under other protective coatings. 4 Principle A coated test panel is scribed in a defined way. A small amount of sodium chloride is introduced into the scribed mark, either by dipping the panel in a solution of the salt or by exposure to salt-fog. The panel is then exposed in a test cabinet at 40 Cand a relative humidity of 80 %. The effects of exposure are evaluated by criteria agreed in advance between the interested parties, these criteria either being of a subjective nature or as given in ISO Required supplementary information For any particular application, the test method specified in this part of ISO 4623 needs to be completed by supplementary information. The items of supplementary information are given in annex A. 6 Sampling Take a representative sample of the product to be tested (or of each product in the case of a multi-coat system), as specified in ISO Examine and prepare each sample for testing, as specified in ISO Apparatus Ordinary laboratory apparatus and glassware, together with the following: 7.1 Test cabinet, capable of being maintained at (40 ± 2) C and a relative humidity of (80 ± 5) %, and having provision for placing or hanging the test panels in an approximately vertical position so that the distance between the faces of adjacent panels is at least 20 mm. NOTE If a cabinet with automatic humidity control is not available, the specified humidity may be obtained by means of a saturated aqueous solution of ammonium sulfate. This gives a constant relative humidity of 79 % at 40 C (see ISO 483). Further details and guidance are given in annex B. 8 Reagents 8.1 Sodium chloride solution (for the dipping technique). Unless otherwise specified, prepare the solution by dissolving 1gof analytical grade sodium chloride in 1 litre of distilled or demineralized water of at least grade 3 as defined in ISO Place the solution in a vessel suitable for complete immersion of the test panel (see 9.1 and ).

Fästelement Sextandhålsskruvar med cylinderhuvud (ISO 14580:2001) Hexalobular socket cheese head screws (ISO 14580:2001)

SVENSK STANDARD SS-EN ISO 14580 Fastställd 2001-09-28 Utgåva 1 Fästelement Sextandhålsskruvar med cylinderhuvud (ISO 14580:2001) Hexalobular socket cheese head screws (ISO 14580:2001) ICS 21.060.10 Språk: