Skärande verktyg Verktygshållare med cylindriskt fäste Del 6: Typ E med cylindriskt säte (ISO :2004, IDT)

Size: px

Start display at page:

Download "Skärande verktyg Verktygshållare med cylindriskt fäste Del 6: Typ E med cylindriskt säte (ISO :2004, IDT)"

Duane Williams
5 years ago
Views:

SVENSK STANDARD SS-ISO 10889-6:2004 Fastställd 2004-12-03 Utgåva 2 Skärande verktyg Verktygshållare med cylindriskt fäste Del 6: Typ E med cylindriskt säte (ISO 10889-6:2004, IDT) Tool holders with

1 SVENSK STANDARD SS-ISO :2004 Fastställd Utgåva 2 Skärande verktyg Verktygshållare med cylindriskt fäste Del 6: Typ E med cylindriskt säte (ISO :2004, IDT) Tool holders with cylindrical shank Part 6: Type E with cylindrical seat (ISO :2004, IDT) ICS Språk: engelska Publicerad: januari 2005 Copyright SIS. Reproduction in any form without permission is prohibited.

2 Den internationella standarden ISO :2004 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av ISO :2004. Denna standard ersätter SS-ISO , utgåva 1. The International Standard ISO :2004 has the status of a Swedish Standard. This document contains the official English version of ISO :2004. This standard supersedes the Swedish Standard SS-ISO , edition 1. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, telefon Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, STOCKHOLM Telefon: Telefax: E-post: sis.sales@sis.se. Internet:

3 SS-ISO :2004 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 29, Small tools. This second edition cancels and replaces the first edition (ISO :1997), Table 3 of which has been technically revised. ISO consists of the following parts, under the general title Tool holders with cylindrical shank: Part 1: Cylindrical shank, location bore Technical delivery conditions Part 2: Type A, shanks for tool holders of special designs Part 3: Type B with rectangular radial seat Part 4: Type C with rectangular axial seat Part 5: Type D with more than one rectangular seat Part 6: Type E with cylindrical seat Part 7: Type F with taper seat Part 8: Type Z, accessories ISO 2004 All rights reserved iii

5 SS-ISO :2004 Tool holders with cylindrical shank Part 6: Type E with cylindrical seat 1 Scope ISO is applicable to tool holders with cylindrical shank for machine tools with non-rotating tools, preferably for turning machines. This part of ISO specifies dimensions, designations and complementary technical delivery conditions for tool holders with cylindrical seat of types E1 to E4 with a mounting system cylindrical shank in accordance with ISO For non-standardized tool holders such as tool holders with a cylindrical seat as shown in the figures, it is advisable to apply the corresponding specifications of this part of ISO Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO , General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO , General tolerances Part 2: Geometrical tolerances for features without individual tolerance indications ISO , Tool holders with cylindrical shank Part 1: Cylindrical shank, location bore Technical delivery conditions ISO 10897, Collets for tool holders with taper ratio 1:10 Collets, holders, nuts ISO 15488, Collets with 8 setting angle for tool shanks Collets, nuts and fitting dimensions 3 Dimensions 3.1 General Unspecified details shall be chosen appropriately. General tolerances: ISO 2768-mH. 3.2 Tool holder of type E1 See Figure 1 and Table 1. ISO 2004 All rights reserved 1

6 SS-ISO :2004 Provläsningsexemplar / Preview Dimensions in millimetres, surface roughness in micrometres a Cylindrical shank in accordance with ISO Figure 1 Type E1 tool holder for drilling tools with internal coolant supply 2 ISO 2004 All rights reserved

Bildmaterial Oframkallad fotofilm och fotopapper

SVENSK STANDARD SS-ISO 18928 Fastställd 2003-07-11 Utgåva 1 Bildmaterial Oframkallad fotofilm och fotopapper Förvaring Imaging materials Unprocessed photographic films and papers Storage practices ICS