SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET or ELECTROSTATIC POWDER PAINTING
|
|
- Reynold Manning
- 5 years ago
- Views:
Transcription
1 CHIEF CHEMIST DEPT. PAGE No. 1 of 7 SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET or ELECTROSTATIC POWDER PAINTING 1. SCOPE This specification covers the requirements for painting of steel surfaces hot dipped or electrolytically galvanized. Galvanized steel shall be protected by paint (duplex system) except for threaded items such as nuts and bolts which will be chromated according to the instructions of the laboratory of materials. Painting on galvanized surfaces may be problematic and a test patch is recommended in order to assure a proper adhesion of the primer on the prepared surface. In each project it's recommended to enable a patch test before the work. The project manager will choose the painting system according to the environment and to the kind of galvanized layer. 2. SURFACE PREPARATION 2.1. On hot dip Galvanized items Solvent cleaning Cleaning all surfaces from dirt, dust, oil, grease using a suitable solvent to SSPC SP-1. Approved Chemitaas products: Ardox 6-551, BC-70 or similar products of other manufacturers. App.2-1
2 CHIEF CHEMIST DEPT. PAGE No. 2 of Surface treatment By one of the following methods: A. Brush-off blast cleaning According to SSPC-SP-7 specification. Will be performed only by authorized workers. Authorization shall be granted after ability to perform roughening of the zinc coating and remove no more than 10 microns of the zinc layer. The zinc layer thickness shall be examined before and after blasting. B. Chemical treatment Submerging the item in a phosphating bath type ZINC-PHOSPHATE conforming to BS standard. 2.2 On electrolytically galvanized items Solvent cleaning According to par Surface treatment By one of the following methods: A. Mechanical The surface shall be roughened to a degree suitable for the specified paint system. Approved surface cleaning media are listed in par B. Chemical treatment according to par B. App.2-2
3 CHIEF CHEMIST DEPT. PAGE No. 3 of 7 3. PAINTING ENVIRONMENT SUBSTRATE PAINTING SYSTEM THICKNESS MICRON REMARKS 3.1 Internal location Hot dip or external in a galvanizing dry environment zinc layer thickness over 80 micron Liquid paints Epoxy polyamide modified special for galvanizes surfaces / two component aliphatic polyurethane Total Electrostatic power painting with pure polyester Total See par. 4.1 for products see par. 6.1 and 6.2 remarks See par. 4.2 for manufacturers and Electrolyticaly galvanizing micron zinc layer thickness Liquid paints Epoxy polyamide modified special for galvanized surfaces 70 See par. 4.1 for products Two component aliphatic polyurethane. Total See par. 6.1, 6.2 Remarks. ` Electrostatic painting with pure polyester Total See par. 4.2 for App.2-3
4 CHIEF CHEMIST DEPT. PAGE No. 4 of 7 ENVIRONMENT SUBSTRATE PAINTING SYSTEM THICKNESS MICRON REMARKS 3.2 External location marine or industrial fume environment Hot dip galvanizing zinc layer thickness over 80 micron Liquid paint epoxy polyamide modified special for galvanized surfaces 70 See par. 4.1 for Two component Aliphatic Polyurethane 50 See par. 6.1 and 6.2 Remarks Electrostatic painting External location marine or industrial fume environment Electrolitically galvanizing micron zinc layer thickness Prime: Epoxy. Top: pure polyester Total Epoxy polyamide modified special for galvanized surfaces See par. 4.2 for manufacturer. See par. 4 for manufacturers and Two component aliphatic polyurethane 50 Total Electrostatic painting Prime: Epoxy. Top: pure polyester Total See par. 4.2 for manufacturers. App.2-4
5 CHIEF CHEMIST DEPT. PAGE No. 5 of 7 4. Paint products 4.1 Wet painting procedure above galvanized surface Manufacturer Tambour Nirlat Carboline Sherwin williams Ameron Sigma International Freitag Primer Epitamarin Uniseal brown code 842-xx or Epogal code 644-xx Epoxy Primer 524 Rust Bond Penetrating Primer Duraplate 235 Amercoat TC 71 Sigmacover 522 Or Sigmacover 280 Interguard 269 Vigor EP 201C Top Tamaglass PU (Aliphatic) Unicryl Carboline 134 ACROLOM 218 Amercoat 450 S Sigmadur 520 Interthane 990 Vigor PU Electrostatic painting Manufacturer Tambour Nirlat - Univercol David Powders Product name Polyester Shamir Polyester Unilac Polyester Remarks 185-xxx series 7000 App.2-5
6 CHIEF CHEMIST DEPT. PAGE No. 6 of 7 5. Technical Requirement for electrostatic painting Laboratory tests will be carried out on panels measuring 100 x 150 x 0.7 mm. 5.1 Thickness of Coating At least 80 Microns. The test to be according to SSPC-PA1/ Adhesion Pull-off according to ASTM D Test dolly 20 mm. Using Acrylic Adhesive (DP-805, Scotch-weld or equivalent). Minimum 1000 psi. 5.3 Hardness Hardness of coating to scratching: 4000 gr. According to ISO R Impact According to ASTM D-2794: 25 Kg/cm. Will not be every cracking of the coating, nor any detachment from the substrate. 5.5 Extensibility ISO-1520-Erichsen Cupping: 6 mm without cracks or detachments. 5.6 Permeability A coated panel will be partially submerged in pressure cooker containing distilled water to a level of at least 25 mm. Cooking at least for two hours after the appearance of steam. After cooling of the cooker and the panel, the coating should be examined: no bubbles should appear on the surface. (They are acceptable only near the edges). 5.7 Resistance to Salt Spray Fog: Three panels will be placed in al salt water chamber for 1000 hours after being cross-cut in the center of the plate with an X, mm long. After drying for 24 hours at room temperature, adhesion to the cross-cut will be examined. Spread of rust along the lines and separation of the coating must not exceed 2 mm. There must be no bubbles or rust spots on the surface remote from the cut and the edges of the plate. CHIEF CHEMIST DEPT. PAGE No.7 of 7 App.2-6
7 6. Quality assurance Is based on the authorization of the process and manufacturer that shall be granted after ability to supply panels that will conform the requirements specified in par.5. During the fabrication only thickness off the coating will be checked. There are not permitted measurements under the specified thickness in par.5.1. REMARKS 1. Damaged hot dip galvanized surfaces must be repaired by applying at least two coats of organic zinc rich coatings to give a minimum dry film thickness of micron. Approved products: Z.R.C I.E.C - distributor carmel handasa catalog no ZINGA - distributor m.b.l catalog no ZINC-GLAD 5 - distributor Chemital catalog no GLAVITE 90 E - distributor tambour catalog no In the painting system will be involved only paints from the same manufacturer 3. Every two successive coats must be colour contrasted. 4. I.E.C. will approve only paint products that permit over coating with the paints specified in par The result of adhesion test performed after over coating according to Israeli Standard 785/27 will be at least level Surface profile producing media recommended: non-woven abrasive wheels and discs such as: 3 M Scotch-Brite clean strip discs and wheels. Coated abrasive discs (sending pads) as: Flap wheels such as: Grind 0 Flex Wheels from Merit Corporation Needle guns consisting of a bundle of wire needles which can impact the surface. Prepared: Y. Casapu Revised by Shay Litani (June 2012) Approved: Dr. E. Sutskover App.2-7
SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET/ELECTROSTATIC POWDER PAINTING
CHIEF CHEMIST DEPT. PAGE No. 1 SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET/ELECTROSTATIC POWDER PAINTING 1. SCOPE This specification covers the requirements for painting of steel surfaces
More informationSuggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002
Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002 This suggested specification is provided as a guide to preparing a quality document calling for
More informationRAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION
Suitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection. Easy to apply Excellent anti-corrosion resistance Can be applied
More informationGeneral description: Two-component high-build, high solids surface tolerant universal epoxy coating. For painting on steel and galvanized steel substrates. Certified for systems category C5I High ISO 12944.
More informationBarofor Round System (polyester coated) Panels, Posts, Accessories
1 Scope This Technical Data Sheet specifies the requirements for the Barofor Round System. The complete system exists of: Panels Posts Accessories such as fixation system and posts caps. Panels and posts
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationPRODUCT GUIDE: CATALYZED PRIMERS. Version:
PRODUCT GUIDE: CATALYZED PRIMERS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy, and
More informationThese Application Instructions cover surface preparation, application equipment and application details for HEMPADUR MASTIC 45880/45881.
For product description refer to product data sheet HEMPADUR MASTIC 45880/ HEMPADUR MASTIC 45880/ High temperatures: 45881: BASE 45889 with CURING AGENT 95881 Low to medium temperatures: 45880: BASE 45889
More informationFor questions, concerning corrosion protection, contact our Mr. Franke under Telephone No. +49-(0) , or Fax No.+49-(0) ).
SCHORCH Paint System (Author: Hinrichs / Dep. Q1) Contents 1: General 2: Warranty / paint systems to customers specifications 3: Contact person at SCHORCH 4: Attached index 5: Site conditions of SCHORCH
More informationPRODUCT GUIDE: CATALYZED TOPCOATS. Version:
PRODUCT GUIDE: CATALYZED TOPCOATS Version: 08.07.17 ELITE COATINGS PRODUCT DATA PRODUCT: Low VOC High Solids Aliphatic Urethane Product Number: 4045 DESCRIPTION: 4045 is a top of the line 2 component urethane
More informationBUREAU OF INDIAN STANDARDS. Draft Indian Standard TWO COMPONENTS HIGH BUILD EPOXY MICACIOUS IRON OXIDE (MIO) PIGMENTED INTERMEDIATE COAT SPECIFICATION
FOR BIS USE ONLY DOC:CHD 20 (1932)C December 2012 BUREAU OF INDIAN STANDARDS Draft Indian Standard TWO COMPONENTS HIGH BUILD EPOXY MICACIOUS IRON OXIDE (MIO) PIGMENTED INTERMEDIATE COAT SPECIFICATION (Not
More informationTechnical Data Sheet ACRYLIC FILLER 4:1 Acrylic filler with anti-corrosion additives RELATED PRODUCTS. Acrylic and polyurethane thinner
Acrylic filler with anti-corrosion additives RELATED PRODUCTS Acrylic filler hardener Acrylic and polyurethane thinner PROPERTIES A product designed and dedicated for renovation of classic cars Universal
More informationsteelwise BEST OF BOTH WORLDS
Duplex systems employing painting or powder coating over hot-dip galvanized steel blend longterm protection with desired aesthetics. Here is some practical advice on successfully specifying and getting
More informationPaints and varnishes Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint systems
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 12944-5 Third edition 2018-02 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint
More informationAquaCLAD Water-Reducible Rust Preventative Alkyd
AquaCLAD 1600 Water-Reducible Rust Preventative Alkyd A rust preventative coating for interior and exterior steel in mild to moderate industrial environment. Recommended For Features Refinish Market High
More informationKnowledge Requirements. Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator. trainthepainter.
Knowledge Requirements Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator trainthepainter.com Knowledge Requirements The Knowledge Requirements the protective coatings
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More informationDULUX UNIVERSAL UNDERCOAT
TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Intermediate coating for use under decorative topcoats, for interior and exterior use PRODUCT
More informationEXTERIOR PAINTING
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationBallast pipe system, leaking
APPLICATION REPORT Ballast pipe system, leaking Application: Place: Repair of approx. 50 leaks on ballast system Offshore, Congo Africa Date: November 2005 Job and report done by: Wencon products used:
More informationPhysical constants Finish: ASTM D Flash point: Rangan Far, s Adding thinner to a paint may change the flash point of the diluted material.
Finish: The appearance of the paint film after drying under optimum conditions,- given as high gloss (>90), gloss (60-90), semi-gloss (30-60), semi-flat (15-30), or flat (
More informationSeawater / CW pipes leaking
APPLICATION REPORT Seawater / CW pipes leaking Application: Place: Seawater / CW pipes leaking Denmark Date: May 2014 Job and report done by: Wencon materials used: Assens Skibsværft, Assens, DK and Wencon
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust
More informationCold curing adhesive K-X280
Instructions for use English Cold curing adhesive K-X280 A4048-1.0 en English 1 Safety instructions... 3 2 General information... 3 2.1 Scope of delivery for K-X280... 3 2.2 Accessories required for installation...
More informationUP133 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CL
UP33 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL TRIANGLE
More informationEMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL
EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 2521;402 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc
More informationA-LF-Sea. Application Manual for M&R. (Full blasting)
Application Manual for M&R (Full blasting) April 2015 1 Contents 1.Standard scheme 1)Standard scheme for flat & vertical bottom 2)Colour scheme for system 2.High pressure fresh water washing (HPFWW) 1)Timing
More informationK 200/ Acrylic Urethane Primer Surfacer Form P-151 (9/91)
K 200/ Acrylic Urethane Primer Surfacer Form P-151 (9/91) K 200 IDENTITY CODE Primer Surfacer K 200 Primer Surfacer Hardener K 201 Flexible Primer Surfacer Hardener K 248 DT Reducers Cool Temperature Reducer
More informationJiangsu DAQO. Enclosed Busbar Systems. Procedure Specification. Painting Procedure Specification
Company Jiangsu DAQO Edition No.1 Name Enclosed Busbar Systems Co., Ltd Files Procedure Specification Serial DQFM-ZD-08-004 Classes Painting Procedure Specification 1 Surface Treatment before Painting
More informationBRUSH APPLICATION INSTRUCTIONS
QUALITY MARINE EQUIPMENT SINCE 1981 Antifouling Paint For Metal Under The Waterline BRUSH APPLICATION INSTRUCTIONS www.antifoulingpaint.net TABLE OF CONTENTS Humidity & Drying Metal Surfaces... 1 Coverage
More informationThe required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification.
Technical Data Sheet 14880 1 14880 acrylic VValidationDate). 1 Product description This is a one component solvent based acrylic thin film intumescent coating. Independently approved for fire protection
More information3M Scotchkote System Application Guide. High Performance Corrosion Resistant System for Plastisol Coated Metal Cladding
High Performance Corrosion Resistant System for Plastisol Coated Metal Cladding - Issue 1 Surface Preparation & Cleaning Application of Patch Primer to Corroded Areas Application of Primer to Patch Primed
More informationPAINT SYSTEMS Polyester yachts
PAINT SYSTEMS Polyester yachts Polyester osmosis renovation Polyester osmosis repair Polyester below the waterline Polyester above the waterline Polyester decks Polyester superstructure Polyester interior
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline SPRAY. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline SPRAY Application Instructions www.antifoulingpaint.net Thank you for selecting Velox Plus Antifouling Paint to protect
More informationWEGTHANE HPA 501 (HPA 501/ HPA 502/ HPA 503/ HPA 504)
WEGTHANE HPA 501 (HPA 501/ HPA 502/ HPA 503/ HPA 504) PRODUCT DESCRIPTION: INTENDED USES: Bicomponent gloss aliphatic acrylic polyurethane finishing paint, with excellent durability and extended repainting.
More information1. Labels: Do not paint over UL, FMG, or other code-required labels or equipment name, identification, performance rating, or nomenclature plates.
SECTION 09 9100 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 7141;9820 1,2 7141 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically cured aliphatic polyester polyurethane coating.
More informationTECHNICAL SPECIFICATION FOR STEEL DRY CARGO CONTAINER 6'x1960mmx1920mm TYPE
TECHNICAL SPECIFICATION FOR STEEL DRY CARGO CONTAINER 6'x1960mmx1920mm TYPE 1. General 1.1 Scope This specification will cover the design, construction, materials, testing and inspection performances of
More informationTechnical Data Sheet Primers/Surfacers LV 250 Primer EP /005 FOR PROFESSIONAL USE ONLY
100 2505-001/005 50 2505-104 40 2505-204 2505-205 12 Description: Autocoat BT LV 250 Primer EP is a quick drying, chromate-free high solid two-pack epoxy primer-surfacer for shot blasted steel substrates..
More informationSECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTechnical Data Sheet Primers/Surfacers LV 350 Primer EP FOR PROFESSIONAL USE ONLY
4 3505-002 1 3505-105 0.5 3505-204 Description: High solid two-pack epoxy primer-surfacer providing excellent appearance and corrosion protection. The target use for this product is refinishing and refurbish
More informationIndustrial and Transportation Business DISTRIBUTOR PRODUCT LINE
Industrial and Transportation Business DISTRIBUTOR PRODUCT LINE 3900 DUCT TAPE 3900 DUCT TAPE MRO (Maintenance and Repair) Construction Trade Shows and Conventions General Industrial Electrical Aerospace
More informationPanel fencing system 2D 6/5/6
tel.: +8 7 2 2 mobile: +8 09 9 e-mail: kontakt@ Panel fencing system 2D // fencing panels tel.: +8 7 2 2 mobile: +8 09 9 e-mail: kontakt@ type 2D H H Panel height 0 80 00 20 0 0 80 200 220 20 Horizontal
More informationThe required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification.
Product description This is a two component chemically cured aliphatic polyester polyurethane coating. It has a high gloss finish with excellent gloss retention. It has excellent chemical resistance. To
More informationExplorer Roof Rack Fitting Instructions: Roll Cage Mounted models only
Explorer Roof Rack Fitting Instructions: Roll Cage Mounted models only These instructions cover the fitting of the following rack models: RRL229 0FRC/0LRC/0SRC/0NRC - Defender 90 HT/SW Roll Cage Mounted
More informationBig Sky Product Information Sheet. Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide)
Big Sky Product Information Sheet TECHNICAL SUPPORT ((800) 328-4892 P.I. Sheet #3008 Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide) READ ENTIRE PRODUCT
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Coatings Research Group, Inc. 125 Pelret
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationWEGPOXI WET SURFACE 89 PW ALUMINUM
WEGPOXI WET SURFACE 89 PW ALUMINUM PRODUCT DESCRIPTION INTENDED USES Bicomponent epoxy polyamine primer, of high solids, high thickness and with anticorrosive pigmentation with an aluminum base, providing
More informationPainting Safety Procedure
Pars Oil & Gas Company Painting Safety Procedure HEALTH, SAFETY AND ENVIRONMENT PROCEDURE Painting Safety Procedure DOCUMENT ID - PR-66-POGC-002 REVISION 0.0 Pars Oil & Gas Company Pages 10 Revision 00
More informationOHIO TURNPIKE AND INFRASTRUCTURE COMMISSION ADDENDUM NO. 1 BID INVITATION NO EIGHT (8) EACH UTILITY BODY AND POWER LIFTGATE
OHIO TURNPIKE AND INFRASTRUCTURE COMMISSION ADDENDUM NO. 1 EIGHT (8) EACH UTILITY BODY AND POWER LIFTGATE OPENING DATE: 2:00 P.M. (EASTERN TIME), OCTOBER 10, 2017 ATTENTION OF BIDDERS IS DIRECTED TO: ANSWERS
More information06/09/54. Theory of Rust
Theory of Rust 1 Type Of Corrosion Protections - Painting System Polyurethane Base, Epoxy Base, Oil Paint, Fluorine Base Type Of Corrosion Protections - Insulation System Fiberglass, Close cell PE 2 Type
More informationMETAL METAL
12654 - METAL 12654-1 PART ONE: GENERAL METAL 1.1 Architectural metals shall be of the best commercial quality and their various forms shall be straight and true. There shall be no scratches, scars or
More informationSTANDARD SPECIFICATION FOR SHOP AND FIELD PAINTING
STANDARD SPECIFICATION FOR SHOP AND FIELD PAINTING SPECIFICATION FOR PAINTING PAGE: 1 of 10 STANDARD SPECIFICATION FOR SHOP AND FIELD PAINTING 1.0 GENERAL 1.1 These technical specifications shall be applicable
More informationRuncorn: A Project First for Europe
Page1 Runcorn: A Project First for Europe A Combination of Film-Galvanising and Hot-Dip Galvanising This is an interesting look at the first project in Europe to use both film-galvanising and hot-dip galvanising
More information2K weather resistance clear coat A850
Clear coat Donglai Coating Technology (Shanghai) Co., Ltd. 2K weather resistance clear coat A850 Description High-build, two-component clear coat designed for universal application and optimal appearance
More information3M Scotchkote System Application Guide. High Performance Coating System for Degraded Plastisol Cladding Surfaces.
High Performance Coating System for Degraded Plastisol Cladding Surfaces. - Issue 2 Surface Preparation & Cleaning Primer Stage Finish Coat(s) As required 3M Scotchkote Epoxy Primer MC 135 @ 50µ Theoretical
More information6043 DESIGN AND TECHNOLOGY
www.onlineexamhelp.com www.onlineexamhelp.com CAMBRIDGE INTERNATIONAL EXAMINATIONS GCE Ordinary Level MARK SCHEME for the October/November 2013 series 6043 DESIGN AND TECHNOLOGY 6043/01 Paper 1, maximum
More informationRequirement for Holes - Holes for Hanging
Requirement for Holes - Holes for Hanging In order for items to progress through the series of pretreatment and galvanizing baths at our facility, they must be suspended in a suitable manner to ensure
More informationReliable solutions with optimised performance
Reliable solutions with optimised performance 3M innovation provides quality you can count on in a full line of premium engineered abrasives and convenient all-purpose abrasive products for use in stock
More informationSprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E".
Product Name Nordic Flow FM Thin Wall Pipes Application Sprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E". Manufacturing Standard
More informationA. Section includes surface preparation and the application of paint systems on exterior substrates.
SECTION 09 91 13 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationVersai Evolution of Versatile Fencing
Versai Evolution of Versatile Fencing About Versai Ornamental Fencing Versai Ornamental Fencing Versai Ornamental Fencing by Fortress is the next generation in ornamental fencing. It offers a solution
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12944-6 First edition 1998-05-15 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 6: Laboratory performance test methods Peintures
More informationThe required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification.
Technical Data Sheet 402;2521 1 2521 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product.
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099123 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Coatings Research Group, Inc. 125 Pelret
More informationSECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationMATERIAL AND EQUIPMENT STANDARD FOR ZINC SILICATE (INORGANIC ZINC-RICH) PAINT PRIMER, INTERMEDIATE AND TOP COAT ORIGINAL EDITION MAY 1993
MATERIAL AND EQUIPMENT STANDARD FOR ZINC SILICATE (INORGANIC ZINC-RICH) PAINT AS PRIMER, INTERMEDIATE AND TOP COAT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant
More informationmiramondo Technical Informations 1/6 Passepartout Concrete
1/6 Passepartout Concrete Technical Informations Passepartout Concrete 2/6 Dimensions 590 600 1785 590 600 1785 250 150 400 700 Hole pattern for mounting 590/1785 504/1699 43 590 324 133 D 12 Passepartout
More informationPRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
More informationApplication Guide for Jotun Primax Diamond Powder Coatings
for Jotun Primax Diamond Application Guide for Jotun Primax Diamond Powder Coatings Date of Last Revision: August 2017 Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview 3 3.0 Safety Considerations..3
More informationNOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY).
Product Description PHOENIX PAINTS MAXICOAT 100 is a 2 Pack Water-Dispersed Top Coat which not only exhibits the physical and chemical strengths of epoxy, but also the safety and convenience of water as
More informationTechnical Data February, 2016
Technical Data February, 2016 Product Description 3M DP-600 is a non-sag, grey, rapid setting, two-component polyurethane. It is packaged as 1:1 ratio liquids in a duo-pak cartridge. With the squeeze of
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline ROLLER. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline ROLLER Application Instructions www.antifoulingpaint.net THANK YOU! Thank you for selecting Velox Plus Antifouling Paint
More informationStreet Design. BUCKLAND seating. Buckland bench product details. Buckland technical specification. Buckland accessories. Buckland material finishes
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us BUCKLAND seating As UK based, designers and manufacturers, Street Design can manufacture
More informationSECTION 025 INDUSTRIAL PAINTING
SECTION 025 INDUSTRIL PINTING Industrial painting, including all necessary preparation and application, except as modified in this Section, shall conform to the recommendations of the manufacturer of the
More informationA: Proposed Scope of Services. B: Site Location Map. C: Selected existing conditions photographs.
The Wise Economy Workshop 3570 Sherbrooke Drive Cincinnati, OH 45241 USA 1.513.288-6613 12 North South Street Attachments: A: Proposed Scope of Services. B: Site Location Map. C: Selected existing conditions
More informationBetter by Design. PVC Coated Conduit System. Technical Services Tel: Canada Tel: Fax:
PVC Coated Conduit System Overview Ocal Blue PVC coated conduit and fittings represent a complete corrosion protection package for your entire conduit system. This extensive product line includes the largest
More informationSILICONE RESIN PAINT FOR MASONRY FACADES
TIKKURILA SILICONE RESIN PAINT FOR MASONRY FACADES DESCRIPTION Water-borne silicone emulsion paint. RECOMMENDED USES Residential, commercial, industrial and storage buildings and others. PRODUCT FEATURES
More informationOntario ENGINEERING STANDARD SPECIFICATION 1/14 REV. CIVIL MATERIAL PROTECTION PAINTS GENERAL REQUIREMENTS. Approved by.
1/1 Rev Description Revision by Approved by Issue Date YYYY/MM/DD 1 Document format and number changed. Previous number 901-01.01.611 AA 2011/12/31 AA 2011/12/31 2012/0/27 2 Approved for use in Thompson
More informationEpoxy Coal Tar. Protects Steel and Concrete in Marine and Industrial Environments.
Epoxy Coal Tar Protects Steel and Concrete in Marine and Industrial Environments. General Epoxy Coal Tar is a protective coating designed to resist chemical attack and rigorous weather conditions by combining
More informationToll-Free
Primary applications for Ross DS Series Security Doors and Frames include government, industrial, commercial and residential properties where protection of people and property is of utmost concern and
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationMATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993
MATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical committee on Nov.
More informationCut Edge Protection Using Prepainted Sheet. Foreword. Section One. Introduction
Foreword Cut Edge Protection Using Prepainted Sheet The National Coil Coating Association (NCCA) would like to thank Laurie Dana, Kim Brandhorst, and Jack Knuttilla of PPG Industries, Inc. for their hard
More informationHP Chromate Free Epoxy Primer P /-4505/-4510
Product Data Sheet September 2011 (February 2013 update) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Chromate Free Epoxy Primers P580-4501/-4505/-4510 Product Description P580-4501 HP Chromate Free
More informationStreet Design. CAMBERLEY seating. Camberley bench product details. Camberley seat product details. Camberley technical specification
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us CAMBERLEY seating As UK based, designers and manufacturers, Street Design can manufacture
More informationSECTION CABLE TRAYS
SECTION 16139 CABLE TRAYS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationCrowdTuff Flat Top Pedestrian Barrier Fencing
Product outline As part of our CrowdTuff powder coated tubular steel fencing range we manufacture a Flat Top style for pedestrian barrier and safety fencing applications. This range of tubular fencing
More informationCITY OF TOMBALL. Section FIRE HYDRANTS 1.01 SECTION INCLUDES. A. Fire hydrants. B. Adjustment of fire hydrants and gate valves.
Section 02520 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 MEASUREMENT AND PAYMENT A. Unit Prices. 1. Payment is on a unit price basis
More informationPRODUCT GUIDE FIRST FOR LASTING IMPRESSIONS
PRODUCT GUIDE FIRST FOR LASTING IMPRESSIONS ULTRIMAX 1 ULTRIMAX 1 ULTRIMAX 1 THE NUMBER 1 FOR SAVING YOU TIME AND EFFORT ULTRIMAX 1 COMPLIANT PRIMER, GLOSS AND VALUE IN ONE Ultrimax 1 is a high build acrylicbased
More informationA. Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Steel and iron.
Farmington, Missouri Project Number M1801~01 PART 1 ~GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMarine. Paint Specification: November ::Fiberglass Substrate:: PAINT that OUTLASTS & OUTPERFORMS
Marine ::Fiberglass Substrate:: PAINT that OUTLASTS & OUTPERFORMS ::Below the Water Line:: System 1 Fiberglass Substrate Pre Treatment Degreaser 10 Additional Requirements Keep surface wet for 5 to 10
More informationSpecification Guide. Portable & Modular Buildings
Specification Guide Portable & Modular Buildings Table of Contents Page Introduction Identifying painting requirements 3 How do I use this specification guide 3 Contacting my local Axalta Coating Systems
More informationSemimatte Volume Solids 55 ± 2% (ISO ) VOC. Overcoating Data 10ºC 25ºC 35ºC Min. 4 hours 2 hours 1 hour Max. 7 2 hours 48 hours 36 hours
W-POXI HIDRO ERP 303 PRODUCT DESCRIPTION: INTENDED USES: Hydrosoluble bicomponent polyamine epoxy primer, with anticorrosive pigmentation and extra quick drying. Items which comply with Directive Rohs
More informationImprove your productivity fast
Improve your productivity fast Executive summary: Up until the recent downturn in the oil and gas industry the previous decade saw unprecedented levels of new construction projects across many industry
More informationSecurifor Polyester Coated Welded Mesh Panels
1 Scope This specification specifies requirements for panels made out of galvanised steel wires, welded and subsequently polyester coated for fencing. The panels are used for fencing, schools, public buildings,
More information