Sample Collection 4 #32056 / 10 Designs

Transcription

1 #32056 / 10 Designs Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen Floral Damask Medallion X 5.17 in X mm 15,927 St. L Chi Floral X 5.75 in X mm 4,418 St. zr L FSL Large Heart 5.60 X 4.49 in X mm 35,801 St. zr L Floral 1 Appliqué 5.09 X 6.89 in X mm 13,249 St. zr L Love 3.82 X 6.23 in X mm 11,160 St. R L Flower Circle X 4.87 in X mm 7,509 St. R HD373 Poinsettias 3.88 X 3.21 in X mm 4,193 St Holiday Bird X 4.80 in X mm 5,655 St. zr L FP637 Floral Appliqué Bookmark X 5.81 in X mm 13,737 St. L NB617_48 Who? 2.74 X 2.23 in X mm 1,584 St. R Some solid It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

2 #32056 / 10 Designs Listings below indicate color sample, stitching order and suggested thread color number. Most numbers indicate Isacord thread. Colors beginning with refer to YLI Fine Metallics, 7 refer to Yenmet Metallic, 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated Floral Damask Medallion 1 n 1. White Detail n 2. Gray Detail Chi Floral 2 n 1. Light Gray Stems n 2. Violet Leaves n 3. Green Veins n 4. Light Yellow Inner Flower Detail n 5. Gold Flower Detail n 6. Pink Flower Detail n 7. Tan Stamens Love n 1. Pink Shading n 2. Red Shading Flower Circle 2 n 1. Single Color Design HD373 Poinsettias 1. One Color Design Holiday Bird 1 n 1. Single Color Design NB617_48 Who? n 1. Branches n 2. Leaves n 3. Owl n 4. Eyes, Feet & Lower Body FSL Large Heart n 1. Single Color Design Floral 1 Appliqué n 1. Leaf Placement Stitch n 2. Tackdown n 3. Light Green Leaf Detail n 4. Green Leaf Detail n 5. Stems n 6. Blue Flower Placement Stitch n 7. Tackdown n 8. Blue Flowers Detail n 9. Orange Flower Placement Stitch n 10. Tackdown n 11. Dark Orange Flower Placement Stitch n 12. Tackdown n 13. Plum Petal Detail n 14. Brown Petal Detail n 15. Orange Petal Detail n 16. Black Outlines n 17. Green Stamen n 18. Yellow Stamens FP637 Floral Appliqué Bookmark 2 1. Pattern/Placement Single Tack Down Zig Zag Tack Down Line Work Leaves Leaves Petals Petal Shading Single Tack Down Match Bobbin & Cover Stitch It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

3 General Freestanding Lace Instructions General Freestanding Lace Guidelines Supplies: General Instructions Embroidery Thread: 1. Hoop two layers of water-soluble stabilizer. Use the same embroidery thread in the bobbin as the needle. 2. Attach the hoop to the machine and select the design of your Needles: choice. Use an Organ 80/12 Titanium needle for extended needle life. 3. Stitch the design. Stabilizer: 4. Remove the hoop from the machine and the design from the Use water-soluble stabilizer or film water-soluble stabilizer. hoop. Trim excess stabilizer from the design. 5. Rinse away remaining stabilizer and allow it to dry. Handy Hints: For Stiffer Lace: DO NOT rinse away all of the stabilizer for a stiffer lace. Note that the thread may appear a shade darker if stabilizer is not removed completely. If you happen to wash too much out, easily re-stiffen by diluting some stabilizer scraps in water and dipping the item in the solution. For Very Soft Lace: Cut away excess stabilizer. Remove remaining stabilizer by rinsing under warm running water until all traces of the stabilizer are gone. Note: If lace should become too limp to work with, dissolve stabilizer scraps in warm water and apply to the lace. Drying Lace: The lace looks best when left to dry completely. Lay lace piece with right side down to dry. This will minimize the tendency for the lace to curl. Be sure to flatten the piece out entirely and allow ample time to dry. Diagram 1 Eyelet Handy Hints: For 3D Lace Projects: Adhere 2 layers of heavy weight stabilizer to back of fabrics with temporary adhesive spray before hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure. Rinsing out lace with very hot water can cause wrinkles in some fabrics after it has been embroidered. To prevent this, pre-shrink cotton fabric by washing it in warm water and drying it in a dryer. If item becomes too limp to work with, iron the appliqué pieces on the wrong side while applying spray starch. After ironing, spray again with starch and allow to dry completely. This will stiffen the lace pieces nicely and aid in construction. A pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (Please see Diagram 1 for explanation of buttonette and eyelet.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet. Buttonette

4 Pre-Cut Appliqué Instructions 1. Print out the necessary pages from the PDF of the appliquè pattern(s). 2. Mark the right side of the pattern pieces so you ll know which direction to lay the pattern on the fabric. 3. Lightly spray the wrong side of the pattern pieces with temporary adhesive spray and allow it to set for a few minutes. 4. Place the pattern pieces on the right side of the fabric and carefully cut them out. PHOTO 1 5. Sew the placement stitch on your hooped fabric. PHOTO 2 6. With the paper still stuck to the right side of the appliqué fabric, spray the wrong side of the fabric with temporary spray adhesive. 7. Place the fabric inside the sewing placement stitch so that it matches the stitching line, and then remove the paper pattern. PHOTO 3 8. Sew the tackdown. PHOTO 4 9. Sew the remainder of the design and repeat for any remaining pieces. PHOTO 5 NOTE: The patterns are sized for the designs as they were made. If you resize the design, you will need to resize the pattern the same amount. You can print out the pattern at the normal size then copy it on a copy machine at the changed size. For example, resize the designs to 80%, resize the printed pattern to 80%. TIP: When Printing the patterns, make sure that the Fit to page option is UNCHECKED in the Print Dialog Box. If this option is checked the printed patterns will not be actual size

5 Supplies: HRFive Temporary Adhesive Spray Embroidery Machine Embroidery Scissors Mark My Words 3 OESD Pack #12059 Bookmark Instructions 1. You will need a piece of fabric large enough to cut out the bookmark twice. 2. Print the template for the design. 3. Fold the fabric in half so wrong sides are facing. 4. Place the template pattern on the fabric. 5. Cut out both the front and back bookmarks at the same time using the template for the design. Fig Hoop one layer of Badgemaster or AquaMesh. 7. Sew the first color. Fig Spray the back of the front bookmark piece with HRFive Temporary Spray Adhesive. Place it in the area sewn by the first color matching up the edges of the fabric with the stitching line. Fig Sew the remainder of the design except the last two colors. a. When you get to the second to the last color, take the hoop off the machine but do not unhoop the stabilizer. b. Spray the wrong side of the back piece of the bookmark with the temporary spray adhesive. c. Turn the hoop over and place the fabric back on the back of the bookmark aligning it with the front piece. (This is where Badgemaster is sometimes easier to work with because you can see through it.) If you use AquaMesh you will need to align it with the stitching line. d. Make sure this piece of fabric is adhered very well. e. At this time, change the bobbin to match the upper thread. 10. Place the hoop back on the machine and continue with the last two colors. 11. Remove the hoop from the machine and the stabilizer from the hoop. Tear away the excess stabilizer. If you use AquaMesh, Figure 2 Figure 3 you may need to cut the excess away and put your bookmark in water to dissolve the excess AquaMesh. Figure 1

6 Printing Instructions ATTENTION When printing this document, any page scaling or page fitting options in your print dialog box must be turned OFF or set to NONE so that your files will print out at their actual size. Images not printed at actual size will not function as intended. TO SAVE PAPER Only print the desired image by navigating to the image s page, go to File > Print and select Current page in the print dialog box. Repeat for each desired image.

7 Appliqué Patterns FP637 Bookmark Pattern It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.