WHITE CHRISTMAS FREESTANDING LACE ADORNMENTS

Transcription

1 WHITE CHRISTMAS FREESTANDING LACE ADORNMENTS # DESIGNS Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen. OC00501 FSL Lace Large Bell Piece Blank Appliqué 4.61 X 8.49 in X mm 36,646 St. L OC00502 FSL Lace Large Bell Piece with Dove Appliqué & Cutwork 4.63 X 8.50 in X mm 45,550 St. L OC00503 FSL Lace Large Bell Piece With Snowflake Appliqué & Cutwork 4.66 X 8.50 in X mm 42,831 St. L OC00504 FSL Lace Large Bell Piece With Star Appliqué & Cutwork 4.66 X 8.50 in X mm 42,831 St. L OC00505 FSL Lace Large Bell Piece Appliqué 4.60 X 8.54 in X mm 45,591 St. L OC00506 FSL Lace Fancy Cutwork 1.50 X 4.25 in X mm 8,838 St. OC00507 FSL Lace Dove Cutwork 2.02 X 2.20 in X mm 5,477 St. OC00508 FSL Lace Snowflake Cutwork 1.58 X 1.82 in X mm 3,231 St. OC00509 FSL Lace Star Cutwork 1.55 X 1.47 in X mm 1,820 St. S OC00510 FSL Lace Ribbon 1.83 X 6.67 in X mm 13,787 St. L S OC00511 FSL Lace Ribbon 2.83 X in X mm 27,584 St. L S OC00512 FSL Lace Tree Skirt Edging 5.27 X in X mm 52,986 St. L OC00513 FSL Lace Name Card Holder Appliqué 4.76 X 6.83 in X mm 36,294 St. L OC00514 FSL Lace Napkin Corner 2.09 X 3.88 in X mm 9,436 St. OC00515 FSL Lace Placemat Corner 2.94 X 6.04 in X mm 19,872 St. L OC00516 FSL Lace Napkin Ring.83 X 5.07 in X mm 9,960 St. L S OC00517 FSL Lace Large Globe Piece with Star Appliqué & Cutwork 3.49 X 9.31 in X mm 37,131 St. L OC00518 FSL Lace Large Globe Piece with Appliqué & Cutwork 3.52 X 9.32 in X mm 39,623 St. L OC00519 FSL Lace Large Globe Piece with Appliqué 3.49 X 9.31 in X mm 35,181 St. L OC00520 FSL Lace Large Globe Piece Blank with Appliqué 3.50 X 9.32 in X mm 29,736 St. L It is a violation of Copyright law to make and distribute copies of software or artwork. Software is licensed to the original purchaser for use at one location OESD, LLC. All rights reserved.

2 WHITE CHRISTMAS FREESTANDING LACE ADORNMENTS # DESIGNS Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen. OC00521 FSL Lace Large Star Piece All Lace 3.60 X 5.16 in X mm 26,092 St. L OC00522 FSL Lace Large Star Piece Half Appliqué 3.61 X 5.19 in X mm 21,459 St. L OC00523 FSL Lace Large Star Piece Appliqué 3.60 X 5.17 in X mm 16,558 St. L It is a violation of Copyright law to make and distribute copies of software or artwork. Software is licensed to the original purchaser for use at one location OESD, LLC. All rights reserved.

3 WHITE CHRISTMAS FREESTANDING LACE ADORNMENTS # DESIGNS Listings below indicate color sample, stitching order and suggested thread color number, Isacord, Yenmet or YLI Variegated threads. OC00501 FSL Lace Large Bell Piece Blank Applique 3. Linework Lace OC00502 FSL Lace Large Bell Piece with Dove Applique & Cutwork 3. Linework Cutwork Guide Stitch Dove Lace OC00503 FSL Lace Large Bell Piece With Snowflake Applique & Cutwork 3. Linework Cutwork Guide Stitch Lace Snowfl ake Lace OC00504 FSL Lace Large Bell Piece With Star Applique & Cutwork 3. Linework Cutwork Guide Stitch Star Lace OC00505 FSL Lace Large Bell Piece Applique 3. Center Linework Lace OC00506 FSL Lace Fancy Cutwork 1. Cutwork Guide Stitch Lace OC00507 FSL Lace Dove Cutwork 1. Cutwork Guide Stitch Dove OC00508 FSL Lace Snowflake Cutwork 1. Cutwork Guide Stitch Snowfl ake OC00509 FSL Lace Star Cutwork 1. Cutwork Guide Stitch Star 0015 OC00510 FSL Lace Ribbon 1 1. Single Color Design OC00511 FSL Lace Ribbon 2 1. Single Color Design OC00512 FSL Lace Tree Skirt Edging 3. Lace OC00513 FSL Lace Name Card Holder Applique 1. Top Pattern/Placement Top Tackdown Top Lace Bottom Pattern/Placement Bottom Tackdown Bottom Lace OC00514 FSL Lace Napkin Corner 3. Lace OC00515 FSL Lace Placemat Corner 3. Lace OC00516 FSL Lace Napkin Ring 1. Single Color Design OC00517 FSL Lace Large Globe Piece with Star Applique & Cutwork 3. Linework Cutwork Guide Stitch Cutwork Star Lace OC00518 FSL Lace Large Globe Piece with Applique & Cutwork 3. Linework Cutwork Guide Stitch Center Lace Lace OC00519 FSL Lace Large Globe Piece with Applique 3. Linework Lace OC00520 FSL Lace Large Globe Piece Blank with Applique 3. Linework Lace OC00521 FSL Lace Large Star Piece All Lace 1. Single Color Design OC00522 FSL Lace Large Star Piece Half Applique 3. Linework Lace OC00523 FSL Lace Large Star Piece Applique 1. Left Pattern/Placement Left Tackdown Right Pattern/Placement Right Tackdown Left Linework Left Lace Right Linework Right Lace It is a violation of Copyright law to make and distribute copies of software or artwork. Software is licensed to the original purchaser for use at one location OESD, LLC. All rights reserved.

4 Collection #3 3D Projects Bell Ornament Each bell requires 6 pieces to create ornament Large Bell Piece (with appliqué) OC00501 Large Bell Piece (with appliqué & dove cutwork) OC00502 Large Bell Piece (with appliqué & snowflake cutwork) OC00503 Large Bell Piece (with appliqué & star cutwork) OC00504 Large Bell Piece (with appliqué) OC00505 Globe Ornament - requires 6 pieces to create ornament Large Globe Piece (with appliqué & star cutwork) OC00517 Large Globe Piece (with appliqué & fancy cutwork) OC00518 Large Globe Piece (with appliqué) OC00519 Large Globe Piece (with appliqué) OC00520 Star Ornament requires 10 pieces to create ornament Star Piece (all lace) OC00521 Star Piece (half appliqué) OC00522 Star Piece (2-tone appliqué) OC00523 Name Card Holder requires 1 piece per name card Name Card Holder (with appliqué) OC00513 Lace Edging Napkin Corner requires 1 piece per napkin Lace Napkin Corner OC00514 Placemat Corner requires 1-4 pieces per placemat depending on look you prefer Lace Placement Corner OC00515 Tree Skirt Edging requires 12 pieces to create tree skirt Lace Tree Skirt Edging OC00512 (design measures 5.27 x and will require a jumbo hoop) Collection #3 Instructions Page 1 of 15

5 Lace Ribbon Ribbon Napkin Ring requires 1 piece per napkin Ribbon napkin ring OC00516 Lace Ribbon requires as many pieces as necessary to create desired length of ribbon Lace Ribbon 1 (6.6 long) OC00510 Lace Ribbon 2 (13.3 long) OC00511 Instructions for Projects of Collection #3 Handy tips: A pair of tweezers, hemostats, or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (Please see Picture 1 below for explanation of buttonette and eyelet for 3D ornaments.) Insert the tip of the hemostats or crochet hook into the eyelet, grasp the buttonette, and pull through. A stiletto could also be used to push the buttonette into the eyelet. The ornaments look and wear better when left fairly stiff. When the design is finished stitching, wash the design lightly so that some of the water soluble stabilizer stays in the design. It is better to hold the ornament gently and allow the water to flow through rather than working at or scrubbing the lace. If item becomes too limp to work with, dissolve scraps of AquaMesh, Aquafilm or BadgeMaster in warm water and apply to the item to re-stiffen. Buttonette Eyelet Picture 1 Collection #3 Instructions Page 2 of 15

6 3D Bell Ornaments - 1) Follow the General Freestanding Lace Guidelines (page 7) and stitch 6 bell pieces per bell ornament. There are 5 different pieces to choose from. They are completely interchangeable so use 6 of the same or mix them up as you wish. 2) With 2 of the 6 stitched pieces, insert a buttonette of piece 1 into the eyelet of piece 2; continue until all 9 buttonettes are inserted into the eyelets. 3) Continue step 2 until all 6 pieces are buttoned together. Please note: to add a hanger to your ornament do not button both sides of piece 6. 4) To add a hanger to your ornament, follow Hanging Your Ornament instructions (page 8). 5) To complete the ornament button piece 6 into piece 1. 3D Globe Ornament 1) Follow the General Freestanding Lace Guidelines (page 7) and stitch 6 globe pieces per globe ornament. There are 4 different pieces to choose from. They are completely interchangeable so use 6 of the same or mix them up as you wish. 2) With 2 of the 6 stitched pieces, insert a buttonette of piece 1 into the eyelet of piece 2; continue until all 11 buttonettes are inserted into the eyelets. 3) Continue step 2 until all 6 pieces are buttoned together. Please note: to add a hanger to your ornament do not button both sides of piece 6. 4) To add a hanger to your ornament, follow Hanging Your Ornament instructions (page 8). 5) To complete the ornament button piece 6 into piece 1. 3D Star Ornament 1) Follow the General Freestanding Lace Guidelines (page 7) and stitch 10 star ornament pieces for each 3D star ornament desired. There are 3 different pieces to choose from. They are completely interchangeable so use 10 of the same or mix them up as you wish. 2) Lay 5 of the pieces together with short sides toward one another (see pic 2 for reference of short side). This will create a flat 5 point star. 3) Start with the short side of piece 1 and insert the 3 buttonettes into the 3 eyelets of piece 2. 4) Continue buttoning buttonettes into eyelets until all 5 pieces are buttoned together. 5) With remaining 5 stitched pieces repeat steps 2 through 4; this will create another flat 5 point star. 6) Place the 2 flat stars with wrong sides together. 7) Create the 3D Star Ornament by inserting the buttonette into the eyelets that line both edges of the flat stars. As you continue to button the pieces together the centers will pop out for the sides to match up. 8) Thread ribbon through 1 of the points of the completed star to hang. Collection #3 Instructions Page 3 of 15

7 Name Card Holder 1) Follow the General Freestanding Lace Guidelines and Appliqué Instructions (page 7) and stitch 1 of design OC00513 FSL Lace Name Card Holder Appliqué. 2) Lay nameplate with right side down. 3) Bring buttonette from pointed end up and insert it into the eyelet in the center of the circle of the opposite end. (Picture 03) Picture 03 4) Finger press the edges of the bottom so that the name card holder will stand up properly. (Picture 04) 5) Insert bottom 2 edges of name card into the slits which are sewn into the front of the name card holder. (Picture 05) Picture 04 Picture 05 Collection #3 Instructions Page 4 of 15

8 Napkin Corner and Placemat Corner There are 2 different methods that can be used with the napkin and placemat corners. You can: A) Embroider the corners as freestanding lace and tack them onto your napkin or placemat. B) Create a lace corner by removing part of your napkin or placemat. Method A Method B Method A 1) Follow the General Freestanding Lace Guidelines and Appliqué Instructions (page 7) and stitch corner design(s). (Designs OC00514 Napkin Corner or OC00515 Placemat Corner) The first color to stitch for the corner designs is a placement stitch that is needed only for Method B. Either skip this color or trim the thread tail that it will leave from both ends of the design. 2) Attach FSL corner to your napkin or placemat by hand tacking in place. Method B 1) Hoop 1 layer of OESD AquaMesh Wash-Away Stabilizer. 2) Attach hoop to machine and stitch only color number 1 of corner design. This will stitch only a placement guide stitch. 3) Remove hoop from machine but do not remove stabilizer from hoop. 4) Spray hooped stabilizer with 101 Quilt Basting Spray. 5) Adhere corner of placemat or napkin to the hooped stabilizer with the edges of the placemat or napkin lining up with the edges of the placement guide stitch. (Picture 06) 6) Reattach hoop to machine and stitch color number 2. This will stitch your cut line. 7) Using small, sharp scissors carefully cut away excess Picture 06 fabric. (Picture 07) 8) Finish stitching design. 9) Remove hoop from machine and stabilizer from hoop. 10) Cut away excess stabilizer. 11) Remove remaining stabilizer by rinsing under warm water. 12) Repeat for other corners as desired Picture 07 Collection #3 Instructions Page 5 of 15

9 Tree Skirt Edging Complete instructions on both embroidering and constructing the tree skirt can be found on page 12. Ribbon Napkin Ring 1) Follow the General Freestanding Lace Guidelines and Appliqué Instructions (page 7) and stitch 1 of design OC00516 FSL Lace Napkin Ring. 2) Insert the buttonette of 1 end into the eyelet at the opposite end to form a ring. 3) Slide napkin ring over folded napkin. Lace Ribbon 1) Follow the General Freestanding Lace Guidelines and Appliqué Instructions (page 7) and stitch as many of designs OC00510 & OC00511 FSL Lace Ribbon as is necessary to create desired length of ribbon. 2) Create one continuous length of ribbon by tacking ends of pieces together by either hand tacking or using the bar tack option on your sewing machine. Cutwork Instructions The following designs contain an area of cutwork: OC D Bell Ornament with Dove Cutwork OC D Bell Ornament with Snowflake Cutwork OC D Bell Ornament with Star Cutwork OC D Globe Ornament with Star Cutwork OC D Globe Ornament with Fancy Cutwork Cutwork designs OC00506, OC00507, OC00508 and OC00509 are also included to be used as accent pieces to coordinate your holiday décor. 1) Hoop one layer of OESD BadgeMaster or OESD AquaMesh Wash-Away Stabilizer with your chosen fabric. 2) Begin stitching design stopping after the Cutwork Guide Stitch. (Picture 08) 3) Remove hoop from machine but do not remove fabric from hoop. 4) Using small sharp scissors, carefully cut fabric away being careful to cut right up to the cut stitch. Do not cut through stabilizer, keep it intact. (Picture 09) 5) Repeat these steps for all cut pieces in the design. 6) Reattach hoop to machine and complete the remaining color changes. (Picture 10) 7) Remove excess stabilizer by following directions on the packaging. Picture 08 Picture 09 Picture 10 Collection #3 Instructions Page 6 of 15

10 Collection #3 Instructions Page 7 of 15

11 Collection #3 Instructions Page 8 of 15

12 Collection #3 Instructions Page 9 of 15

13 Collection #3 Instructions Page 10 of 15

14 Collection #3 Instructions Page 11 of 15

15 SUPPLIES: OESD 2009 Christmas Collection #3 2 ½ yards Red Benartex fabric Fabric for binding edges 3 yards ribbon for ties OESD LightWeight Tear-Away Stabilizer (or tracing paper) OESD AquaMesh Wash-Away Stabilizer Isacord Embroidery Thread for embroidery 101 Quilt Basting Spray Organ Titanium Embroidery needles Size 80/12 Embroidery Machine Sewing machine Tree Skirt with Freestanding Lace Edging PREPARE THE PATTERN: Cut out the printed pattern (page 15). Place the printed pattern over a long length of Tear-Away Stabilizer. Extend both side lines until the total length of each side is 18 ½. Connect the ends of the 2 lines with a straight line. Fold pattern in half lengthwise and crease. Mark along the crease for the straight of grain. CUT OUT SKIRT PANELS: Using the pattern created above cut 12 panels from the red fabric. Note: It is recommended that dark fabrics such as red be pre-washed. EMBROIDER PANELS: Hoop 2 layers of OESD AquaMesh Wash-Away Stabilizer. Attach hoop to machine and stitch only color number 1 of design OC This will stitch only a placement guide. Remove hoop from machine but do not remove stabilizer from hoop. Spray hooped stabilizer with 101 Quilt Basting Spray. PHOTO 01 Adhere one panel to the stabilizer centering edge of fabric within the placement guide. The point of the placement guide stitch will point toward the point of the panel. (PHOTO 01) Reattach hoop to machine and stitch color number 2. This will stitch your cut line. Using small, sharp scissors, carefully cut away excess fabric. (PHOTO 02) Finish stitching design. Remove hoop from machine and stabilizer from hoop. Cut away excess stabilizer. PHOTO 02 Remove remaining stabilizer by rinsing under warm water. Note that we recommend pre-washing your fabric. If after rinsing your panels it appears that your thread is dyed you will need to repeat the rinsing process. Isacord thread will not take on a new color, therefore if it appears that it has, this means that there is starch left on the thread and the starch will hold dye and make the thread appear dyed. Repeat for all 12 panels. Collection #3 Instructions Page 12 of 15

16 CONSTRUCT THE SKIRT There will be approximately ¼ excess fabric on both ends of each panel. Trim corners away by cutting right up to the lace. (PHOTO 03) Place 2 panels right sides together lining up lace. Starting right next to lace, stitch ¼ seam starting at lace. Stitching should be placed right next to the lace. Press seam. Continue stitching panels together until all 12 have been used. Do not stitch 1 st and 12 th panels together as this will need to be left open so that the skirt can be placed around base of tree. PHOTO 03 PERFECTING THE CENTER: The center of your skirt may be a bit jagged. To even this up, take a round object such as a can of spray and center over the hole. Trace around can using a water soluble pen. (PHOTO 04) Cut around drawn circle. FINISHING: To finish edges, bind both raw edges and inside circle. To close skirt, attach ribbon to each open side. (PHOTO 05) PHOTO 04 PHOTO 05 Collection #3 Instructions Page 13 of 15

17 IMPORTANT: When printing the following page the Fit to page option must be UNCHECKED or the Page Scaling option must be set to NONE depending on your printers options. If this option is set incorrectly, the print will not work correctly as a pattern because it will not print at actual size. Collection #3 Instructions Page 14 of 15

18 Collection #3 Instructions Page 15 of 15