Furnace build report
|
|
- Hortense Hudson
- 6 years ago
- Views:
Transcription
1 Furnace build report Cheap and Free Rick is the president of the Metro Detroit Metalworking Club. A few weeks ago we spent the better part of a Sunday over at C&F Rick s house while some aluminum casting was being performed. Rick was making a few practice pours for a demo he was going to do in Ann Arbor. There was also a brass pour made to practice for a cannon pour that may happen this summer. Watching all this go on it s hard to do nothing so I grabbed a hot glue gun, some foam, and Don s hot wire cutter and cut out a fictional engine block. With Ricks guidance the foam was coated in popcorn ceiling/stucco material with the foam balls sifted out. After the coating, the foam was sprinkled in common beach sand and dried with a heat gun to speed things up. The foam was then buried in a bucket of sand and molten aluminum was poured onto the foam and the block was cast. Seeing the results I knew that I would need to build a furnace of my own.
2 Right away I started to gather materials. By the end of the week I had gathered or made all of the things in this photo. The metal 5 gallon bucket, the sheet metal for the lid, my burner tube, the crucible, 2 stainless steel pressure heads, and 3 ingot molds My lid was made from some 4 inch wide sheet metal that was rolled to a 12 inch diameter. There are 2 cheap handles screwed to it. The handles required some field modification to get them to fit the diameter. The center was formed with a 6 inch long piece of 4 inch PVC pipe. The pipe was covered with 3 layers of aluminum foil. I screwed the handles on using 1-1/4 inch long screws. I also put some extra screws in to pin the refractory into the sheet metal.
3 The center of the furnace was formed with a 2 foot long piece of 6 inch PVC pipe. This pipe also was wrapped with 3 layers of aluminum foil. I also drilled 2, ½ inch holes 10-1/2 inches from the bottom of the pipe, so a ½ inch rod could be slid thru the center of the pipe. This rod will hold the pipe 3 inches off the bottom of the bucket when set in. Sorry about no photo of the rod in action. Next a 1-1/8 inch hole was drilled 4 inches from the bottom of the bucket to insert the burner tube. The hole was made on an angle so when the tube is inserted it would just touch the wall inside the 6 inch PVC.
4 The PVC is drilled at 1 inch from the bottom with the same angle. I just eyeballed the entire thing, nothing fancy about it. With a piece of burner tube inserted, the walls of the pipe were touching and the 6 inch was centered in the bucket. The flame will swirl around the crucible instead of blasting right at it.
5 Next the refractory was mixed up. I was told to make a dry mix by the fellow who sold it. Don t mix it wet like concrete because there is a chemical binder that will separate with to much water. It is hard to explain but the refractory when mixed was like shaved ice. If it was poked with a stick it would make a hole and stay that way. When I put it in the bucket it just plopped in but if I shook the bucket hard enough it almost went liquid and self leveled. After marking the inside of the bucket with a depth mark, I put a 3 inch layer of refractory in the bucket. Then the ½ inch rod was inserted thru the 6 inch pipe and the PVC was hung in the bucket. Then the bucket was filled and shaken slowly. As I shook the bucket the refractory wanted to creep up the center of the PVC pipe. Maybe I should have foiled the end of the pipe to keep the refractory down. After the bucket was full a garbage bag was laid out and the lid was also poured. After about 15 minutes, the rod was slid out, and the 6 inch could support itself. Then it was possible to reach down thru the 6 inch pipe and clean out the refractory that worked it way up the center. Also the top will have a divot from the ½ inch rod. That divot needs to be smoothed out at this stage. At this point I pushed a 3/8 bolt into the lid to act as a pivot point for a lid. As it dried, the burner nipple was rotated every so often to keep it from becoming trapped. NOTE: This whole thing required 2-55# bags of refractory and almost used it all.
6 After 3 days cure time the PVC pipe was cut with a saw creating a slot from top to bottom. The width of the saw blade was enough to allow the pipe to collapse in and slip right out leaving an aluminum foil layer in the refractory. The bucket was worked the same way. There were 4 slots cut but the bottom could not be reached with the saw due to the refractory back draft. With the 4 slots I was able to slip the PVC up about ½ inch allowing access to the bottom. One of the cuts was extended thru the bottom and the PVC slipped right out.
7 The furnace is now ready for first fire. I am going to wait a few more days and fire it up. The furnace will be lit with as low a flame possible and then slowly increased over hours until full temperature is achieved. I might even wire brush the lid and put some barbeque paint on it. The burner was made using plans for a burner from The propane regulator and hose setup was recycled from an old torch from work that was no longer fit for service. There was a problem when the furnace was lit and the burner ran extremely rich. After trying 2 other designs, the right burner for my regulator ended up being a variation with (4) 5/16 holes instead of the (6) 3/8 holes, and in the cross tube, a #75 (.021) hole was used instead of the #57 (.043). I am not exactly sure why this combination works and the supplied design did not. I suspect the output pressure may be higher on the regulator that I had but I have no way to confirm that.
8 After the burner problems were worked out, the furnace was lit and brought to temperature slowly over 2 to 3 hours. This was done to chase the moisture out of the refractory slowly to avoid cracking. I now have the equipment to do some casting of aluminum. Now I need to do some reading and practice pours to acquire the skill to make first class castings. Steve Huck, 2009, all rights reserved.
Foundry Procedures. Page 1 of 7 R. G. Sparber Copyleft protects this document. Furnace Set Up
Foundry Procedures Furnace Set Up 1. Check weather report and only proceed if there is no chance of rain 2. lay out tarp on patio 3. place 3 fire bricks to support furnace 4. put down bottom of furnace
More informationObtained from Omarshauntedtrail.com
DaveintheGrave's Halloween Props Animated Crawling Skeleton Build a life-size skeleton torso that realistically crawls across the lawn one arm at a time. 1. Motor Base and Linkage Assembly BASE - I used
More informationFrom "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES
From "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES Carl Ford I have found most commercially available tool handles uncomfortable
More informationDIY Bottom Drain with Air Dome Michael Anderson Atlanta Koi Club
DIY Bottom Drain with Air Dome Michael Anderson Atlanta Koi Club www.atlantakoiclub.org Our koi ponds need bottom drains to take away sinking debris just as it needs a skimmer to trap floating debris.
More informationChapter # 002 : Creating Threaded Metal Anchoring Points in Fiberglass Foam Structures
Chapter # 002 : Creating Threaded Metal Anchoring Points in Fiberglass Foam Structures The following is a method of creating permanent, threaded, metal anchor point in a foam & fiberglass structure. The
More informationPlumbing Part II - Hand Pump
Plumbing Part II - Hand Pump Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 7/17/03 Last Revised: 06/06/2004 The hand pump located in the tender water tank is a backup pump should the axel pump fail
More informationHand drilling a shallow tube-well and fitting a simple Bailer-bucket in Zimbabwe
Hand drilling a shallow tube-well and fitting a simple Bailer-bucket in Zimbabwe Peter Morgan A publication by Aquamor-Zimbabwe. March 2014 Introduction The construction of the lighter duty, simple hand
More informationPREMIUM CONCRETE COUNTERTOP MIX INSTALLATION INSTRUCTIONS
PREMIUM CONCRETE COUNTERTOP MIX INSTALLATION INSTRUCTIONS High Strength Fast Setting Pourable Helpful Items: TCC Materials February 09 Version 2.0 Tools Required: Concrete mixer or ½ drill (600 RPM or
More informationPLK CJ PRODUCT INSTRUCTION PI002 REV Page 1
PLK One Shot Crucible Weld Kit PLK Kit Components CJ One Shot Crucible PLK CJ PRODUCT INSTRUCTION PI002 REV 3 270807 Page 1 PLK The Complete Welding Process The All New Railtech PLK-CJ welding process
More informationCutless Bearing Removal and Replacement for a Watkins 27 By John Everson
Cutless Bearing Removal and Replacement for a Watkins 27 By John Everson This is a fairly difficult job, but if you are mechanically inclined and want to save a significant amount of cash, you might want
More informationHow To Make A Two Part Mold And Cast Crystal Clear Medieval Knight Action Figures.
http://wwwinstructablescom/id/how-to-make-a-two-part-mold-and-cast-crystal-clear/ How To Make A Two Part Mold And Cast Crystal Clear Medieval Knight Action Figures by ComposiMold on March 6, 2015 Table
More informationPump Replacement Manual. Bill Wallace by Wallace Marine Services, Inc.
by Wallace Marine Services, Inc. Maintain Your Equipment The Easy Way Bill Wallace 843-693-4336 info@willyvac.com www.willyvac.com Pump Replacement Manual 1 How to change the water pump on the Willy Vac
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationCan-Do Can Crusher. America s leading woodworking authority. Step by Step construction instruction. A complete bill of materials.
America s leading woodworking authority Can-Do Can Crusher Step by Step construction instruction. A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationObtained from. Omarshauntedtrail.com
BORN2HAUNT.COM http://www.born2haunt.com/batsreasy01.html Bats R Easy Here is another way to make bats with foam and wire. The first thing I did was cut a piece of scrap foam to the size I wanted 5" long,
More informationNotice: New Catalog in Development. (Please scroll down to view the old version)
Notice: New Catalog in Development (Please scroll down to view the old version) Change Search Info ETA.This version of the Greenbarn catalog has served us well for many years, but it is quite "long in
More informationSLATTEX (Textured Slatwall) INSTALLATION GUIDE
SLATTEX (Textured Slatwall) INSTALLATION GUIDE Preparing for the Installation: Here are some suggestions to help you to help you simplify the installation process and maximize the beauty of your 3D Textured
More informationTypes of moulding sand
casting Types of moulding sand 1. Green sand: Green sand which is also known as natural sand is the mostly used sand in moulding. It is basically the mixture of sand, clay and water. The clay contain
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationRosalina Accessories Tutorial Version March 2011 Martyn
Rosalina Accessories Tutorial Version 1.0 - March 2011 Martyn Star Brooch Feel free to experiment with these dimensions, you should make a template you are happy with, the method still works. 1) Creating
More informationPOORMANPROPS SEPTEMBER 24 th Make-N-Take
POORMANPROPS SEPTEMBER 24 th Make-N-Take CREEPY CANDLES Based Off http://www.instructables.com/id/pvc-candles/ Tools: Hack saw or miter saw or PVC cutters (that can cut 1 ½ PVC) Hot glue gun Materials:
More informationSILICONE CAULK MOLD MAKING TUTORIALS
SILICONE CAULK MOLD MAKING TUTORIALS SILICONE CAULK MOLD MAKING TUTORIAL Method #1 Pro s: Fast, cheap in comparison to other mold systems, effective when procedures are followed, these molds can be used
More informationPage 1. Wide Gap 68 CJ Acetylene Product Instruction PI014 Rev
Wide Gap One Shot Crucible Weld Kit Wide Gap Kit Components CJ One Shot Crucible Page 1 T h e Al l N ew Railtech W i d e G a p w e l d i n g pr o c e s s d e s i g n e d f or Au s t r a l i a n c o n d
More informationTwo Categories of Metal Casting Processes
Two Categories of Metal Casting Processes 1. Expendable mold processes - mold is sacrificed to remove part Advantage: more complex shapes possible Disadvantage: production rates often limited by time to
More informationLid, Floor Monument and Two Installation Fixtures. Floor Monument Installed with Lid On and Off
Monumentation Drilling Specifications: Floor Monuments: - Floor is drilled using 1 3/4" core drill bit to a depth of 2 with a Hilti rotary hammer drill - Quikrete is used to set monuments into the floor
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationSnoWizard, Inc. * 101 River Road * New Orleans, LA * *
Another SnoBall season will soon be coming to a close for most operators. This is the time to perform the annual maintenance on the SnoWizard SnoBall Machine. A little preventative maintenance now will
More informationEstate EXTERNAL HALYARD GROUND SET FLAGPOLE INSTALLATION INSTRUCTIONS
Estate EXTERNAL HALYARD GROUND SET FLAGPOLE INSTALLATION INSTRUCTIONS Read these instructions completely before any installation is started. Pay close attention to all safety concerns. In the unlikely
More informationMETAL CASTING PROCESSES
METAL CASTING PROCESSES Sand Casting Other Expendable Mold Casting Processes Permanent Mold Casting Processes Foundry Practice Casting Quality Metals for Casting Product Design Considerations Two Categories
More informationJoe Finch Clay Kiln. Method: Make catenary arch former (65cm wide, 65cm high and 85cm long)
Joe Finch Clay Kiln As with any kiln care must be taken in the construction, sighting and firing of this kiln. For the first firing (if you are firing to biscuit or glaze) you must take the first 700c
More information½ inch PVC Irrigation Full Sliding Coupler and Patch, version 2.0
½ inch PVC Irrigation Full Sliding Coupler and Patch, version 2.0 By R. G. Sparber Protected by Creative Commons. 1 It is an unhappy moment when I discover that I have pierced a PVC irrigation pipe with
More informationPRODUCT INSTRUCTION ONE-SHOT ALUMINOTHERMIC RAIL WELDING PROCESS MRS 86 CRANE RAIL
PRODUCT INSTRUCTION ONE-SHOT ALUMINOTHERMIC RAIL WELDING PROCESS MRS 86 CRANE RAIL MRS 86 CRANE RAIL OXYGEN AND PROPANE PREHEAT ONE-SHOT CRUCIBLE STEMMING PASTE Railtech Australia Limited Po Box 6211 Acacia
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationSANDCASTING. by Joyce Clarin
SANDCASTING by Joyce Clarin Supplies Deeply veined leaf Hosta, rhubarb, burdock, elephant ear, castor bean, cabbage, squash, hollyhock, etc Quikcrete Vinyl Patch Sturdy box (or plastic tray) at least 2
More informationPotter s Wheel Plans. Flywheel is poured in form made by tacking tar paper to plywood disk. Partly set concrete is broom-finished.
Potter s Wheel Plans Flywheel is poured in form made by tacking tar paper to plywood disk. Partly set concrete is broom-finished. Throwing Pottery on a wheel is the most challenging form of pottery making
More informationDesigned by Melissa DiRenzo thesweetescape.ca
instructions Designed by Melissa DiRenzo thesweetescape.ca YOU WILL NEED 3 -diameter foam ball Christmas sweater Hot glue gun and glue sticks 3/8 -wide satin ribbon Elastic thread: metallic Note: A child
More informationDefects but No Failures. By R. G. Sparber. Copyleft protects this article. 12/15/2007
Defects but No Failures By R. G. Sparber Copyleft protects this article. 12/15/2007 A defect is when something does not turn out the way you wanted. A failure is when you don't learn from the experience.
More informationTravis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)
Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach
More informationHow To Make A. Large Diameter Brayer
How To Make A Large Diameter Brayer Charles G. Morgan Mossworks Studio 77 Moss Street Victoria, B.C. V8V 4M2 CANADA 2008 www.mossworks.com charlesgmorgan@yahoo.com I got the basic design for this homemade
More informationPlans for The Siamese Twins
Plans for The Siamese Twins Requests have been pouring in for plans for the Siamese Twins. In fact, another one poured in just last week! So I ve spent the past several days drawing them up. I think it
More informationInstructions: PS-2CD 4000 Model Kit Revised 7/2008
Instructions: PS-2CD 4000 Model Kit Revised 7/2008 Plastic Parts included: Body shell Parts Sprue #1 Roof, trainline, gravity outlet gates, and centersill/endsill pieces Parts Sprue #2 Underframe bolster
More informationCasting Braided Steel
Casting Braided Steel Contributed by: Neil Wright A.K.A Dai SENSEI This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2016 CASTING BRAIDED STEEL By
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationHow to make a paper mache skull
http://www.spookyblue.com/halloween/skulls/paper mache skull.htm How to make a paper mache skull Materials List Resin skull from Anatomical Chart Company What?! Spend $25 on a skull? Hear me out. A good
More informationParts & Tools. O'Cello printing and assembly instructions. o-cello.com
The O'Cello is a 3D-printable cello developed by Conor O'Kane, which is free to download and print for personal use. This document will show you how to print and assemble your own O'Cello. For the latest
More informationSheet Metal Tools. by:prem Mahendranathan
Sheet Metal Tools by: SHEET METAL TOOL KIT SHEET METAL TOOLS Rivet Gun 3/32, 1/8, 5/32, 3/16",Cupped Set Mini Bucking Bar Footed Heel-Toe Bucking Bar Air Tool Oil Mechanics Tool Bag High-Speed Air Drill
More informationIntroduction to Manufacturing Processes
Introduction to Manufacturing Processes Products and Manufacturing Product Creation Cycle Design Material Selection Process Selection Manufacture Inspection Feedback Typical product cost breakdown Manufacturing
More informationHow to Make a Hat Bending Jig
How to Make a Hat Bending Jig MATERIALS One 2" x 8" x 11" long (Base Block) exact measurements are 7 ½" x 1 ½" x 11" (Pine is OK to use, I have used scrap Walnut for my benders) Four pieces of Oak 1" x
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More informationCuckoo Clock Test Hands
Cuckoo Clock Test Hands by Lloyd L. Lehn PhD, CC Purpose: The purpose of this article is to describe the fabrication of a set of test hands I use when servicing cuckoo clocks. Scope: The test hands made
More information10 x 10 Arch Top Pergola
0 x 0 Arch Top Pergola I N S T A L L A T I O N G U I D E O P T I O N A L A C C E S S O R I E S Privacy Fence Panel System ( Panels & Middle Post Included) Bolt Down Bracket Kit (Set of ) Additional Shade
More informationAssembly Instructions: Bencher Skylark
Assembly Instructions: Bencher Skylark Tools Required: Pop Rivet Tool Tape Measure Hex Wrenches Screwdriver Several Disposable Rags Two Saw Horses Several boxes or bowls to hold fasteners and small parts
More informationBlakes 7 DSV-1 Liberator
Blakes 7 DSV-1 Liberator Model kit by Masterpiece Models: www.masterpiecemodels.com Pattern Maker: Alfred Wong Casting: J&S Technologies LLC Parts List Main body 3 Main body nose vanes 4 Main body detail
More informationSolar Panels Build Your Own Instructions for the Do It Yourself Person Let s have some fun!
Solar Panels Build Your Own Instructions for the Do It Yourself Person Let s have some fun! Before we get started lets talk about a few things like materials and tools. Let s start off with tools as Lowes
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More informationA Quick-Change Gearbox For The 7x Minilathe
A Quick-Change Gearbox For The 7x Minilathe Richard Hagenbuch 10 August 2002 This article describes how to a build a quick-change gearbox for your 7X minilathe. I'll describe one that I built as a prototype
More informationThermal Interference Fit Stud, version 2
Thermal Interference Fit Stud, version 2 By R. G. Sparber Follow up information has been added at the end of this article. I wanted to lock a piece of ¼-20 threaded rod into an aluminum knob I made. I
More informationZiroli D-17 Beech Staggerwing
Ziroli D-17 Beech Staggerwing Parts List Vacuform Parts: Miscellanous Pieces 1 Four Side Panels 1 3/16" Tube, 2" Long 2 Lower Dash - Back Dash 2 Felt, 12x24 3 Dash 3 Cordury 12x24 4 Dash Hood 4 Aluminum
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationBlock Foundation. From the 1950s through the 80s. Hydraulically driven. piers provide bearing. for a settling foundation
RESCUING FIXING A A Block Foundation Hydraulically driven piers provide bearing for a settling foundation From the 1950s through the 80s before poured concrete became the norm many homes in northern New
More informationSLIM TRIM MOULDING INSTALLATION METHODS
Slim Trim as a reducer Use SlimTrack (Metal Track) for up to 4 mm floors. Up to 4 mm Floors 3/8 *If the flooring manufacturer suggests/permits the use of underlayments you may need to shim the track to
More informationProducts used in this How To:
How to Slush Cast Products used in this How To: * Original Piece * Alumilite High Strength 3 Silicone Rubber * Alumilite Casting Resin * 610 Foam * Alumilite Liquid Dye or Alumidust * Corrugated Plastic
More informationBuilding a 30 Turntable
Building a 30 Turntable Introduction I wanted a turntable at the North end of my Mystic Mountain railroad to turn trains for point-topoint running and for visual interest. After measuring all my engines
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationAK30 Melter Operation Manual
AK30 Melter Operation Manual This article will help you show the importance of knowing how to operate the AK30 melter. Let s start by making your safety a priority. It is recommended that you wear eye
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationHow to make climbing grips. By,
How to make climbing grips By, Items needed: * Items may be needed depending on your preference. - Carving Foam - Level Table - Cardboard - Pen - Ruler - Straight Edge - Box cutter - Hot melt glue gun
More informationOceanside Outdoor Vinyl Shower Kit (3 x 3 Enclosure)
Oceanside Outdoor Vinyl Shower Kit ( x Enclosure) A B ASSEMBLY GUIDE REQUIRED FOR INSTALLATION (A) Zippity Post Extension for In-Ground Installation (Sold as 4-Packs) (B) Zippity Galvanized Steel Surface
More informationSURFACE CASTING METHOD: For Molds & Core Boxes. Presented by: Hapco Inc.
SURFACE CASTING METHOD: For Molds & Core Boxes Presented by: Hapco Inc. RAPIDFIL Detailed Specifications STEP 1 SPACER LAYER Apply a layer of ¼ foam to create a uniform ¼ thickness around the pattern.
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationWEEK 4 COMPLETE SIDING & EXTERIOR PAINTING
WEEK 4 COMPLETE SIDING & EXTERIOR PAINTING INSTALL DRY WALL CLIPS (STAFF) Safety Briefing Complete siding Caulk exterior plumbing & electrical boxes First Coat Exterior Second Coat Exterior Install siding
More informationAssmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS
Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS General Information Assmann polyethylene storage tanks are manufactured to give you the toughest, most reliable
More informationBefore you begin. Rain Barrel Building Instructions
Before you begin 1. Start with Step 1 (big surprise right?). Note that the remaining steps 2 through 4 can be done in any order as long as you pay careful attention to adhere to the barrel layout. 2. SAFETY
More informationBerea Hardwoods Survival Ballpoint Pen
Berea Hardwoods Co., Inc. Pencil Instructions 18745 Sheldon Road Middleburg Heights, Ohio 44130 Toll Free 1-877-736-5487 Survival Ballpoint Pen (Berea #1602/x-xxx- x) Needed: Mandrel-A Bushing-61A Drills-
More informationAutomated Tiki Torch Installation Instructions
Automated Tiki Torch Installation Instructions Automated Tiki Torch with Poles (Exploded View) 14 Automated Tiki Head 6 8 Tiki Pole (Powder Coated Aluminum or Faux Bamboo Pole) 12 Base Pole (Powder Coated
More informationStall warner - retrofit installation - XS
Stall warner - retrofit installation - XS Part 1 - retrofit to aircraft with XS wings Mark a point on the starboard wing root rib half way between the forward lift pin and the front of the spar, and half
More information10. Wing prep and subassembly
Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right
More informationPermanent Mold Casting Processes. Assoc Prof Zainal Abidin Ahmad Department of Manufacturing & Ind. Eng.
Assoc Prof Zainal Abidin Ahmad Department of Manufacturing & Ind. Eng. Universiti Teknologi Malaysia Permanent Mold Casting Processes Gravity die casting Pressure die casting Low pressure High pressure
More informationMGB V8 Roadster restoration project Report 72
8th September 2016. I thought it would be useful to try this product and report how I got on with it. Reading the instructions it all seemed quite easy. You push the tube down into the box section. Press
More informationTECHNICAL FILE FOR THE STIRLING ENGINE
TECHNICAL FILE FOR THE STIRLING ENGINE FABRICATION RANGE ELEMENT: Support ring SET: Stirling engine RANGE: 1 SHEET: 1 of 1 DRAWING: N 11 MATERIAL: white NUMBER: 1 PVC N o PHASE, SUB-PHASE OR 10 MAKING
More information10 x 10 Flat Top Pergola
0 x 0 Flat Top Pergola A S S E M B L Y G U I D E Models: Venetian, Tuscany, Luxor, Acadia O P T I O N A L A C C E S S O R I E S Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post)
More informationHow to make tailwheel shock rubber donuts and aluminum shims with formed flange
How to make tailwheel shock rubber donuts and aluminum shims with formed flange The following shows how to form a flange on the inner hole of aluminum shims to go between the rubber donuts for the tailwheel
More informationInstalla on Guide: Fence Distributors. YourNextFence.com
TM YourNextFence.com Plan Your Fence each line by dividing the length of each line in inches by 97. Round any remainder up. 2 Calculate Materials Tools Needed Stakes Circular Saw String Line Drill Marking
More informationFor Barrel Tapers. Installation and Operating Instructions for use with table saws and large disk sanders
Tim s Taper Tool For Barrel Tapers Installation and Operating Instructions for use with table saws and large disk sanders Your taper tool is capable of making barrel tapered shafts. The term barrel is
More informationTOOLS & SUPPLIES (Included in ProTops Tool Kit)
TOOLS & SUPPLIES (Included in ProTops Tool Kit) Clean Paint/Mixing Sticks Graduated Mixing Buckets Standard Mixing Cups Nylon Paint Brush Propane Torch 3M Masking Gun Masking Film & Painter s Tape Disposable
More informationBiomass Briquette Mold
Biomass Briquette Mold Drawings and Assembly Compendium Round, Square, Stick, Cube & Chunk By Lee Hite and Dr. Zan Smith Published March 2012 Updated 8/3/2017 All Rights Reserved www.leehite.org Page 1
More informationHollow metal clay forms are typically built over organic cores like. Coreless Construction: Rethinking the Metal Clay
PROJECT INTERMEDIATE METAL CLAY Coreless Construction: Rethinking the Metal Clay Build this four-sided pendant using forethought and a 3-D template. by Cindy Ambrose FCT-MWON0216_ART17 Hollow metal clay
More informationManufacturing Processes - I Dr. D. B. Karunakar Department of Mechanical and Industrial Engineering Indian Institute of Technology, Roorkee
Manufacturing Processes - I Dr. D. B. Karunakar Department of Mechanical and Industrial Engineering Indian Institute of Technology, Roorkee Lecture - 4 Module 2 Metal Casting Good morning, Metal casting,
More informationMachining The Clapper Pin and Hole, Version 2
Machining The Clapper Pin and Hole, Version 2 By R. G. Sparber 08/27/2008 Copyleft protects this article. Since I do metal working as a hobby, I am more interested in the journey than the destination.
More informationSawn Baluster Sizing and Installation Guide
Sawn Baluster Sizing and Installation Guide Welcome to the Durabrac sizing and installation guide for Sawn Balusters. This guide has been prepared to answer any questions you may have about our Sawn Balusters
More informationOmarshauntedtrail.com. Obtained from. Merlin's Wall Sconce.
http://hauntershangout.com/home/wallsconce.asp Plaque Construction Merlin's Wall Sconce Warning: This project uses Electricity! Build at your own risk. Not for children to build. Ever been to a haunt and
More informationSupplies required to build a cardboard boat. (SAMPLE BOAT)
! 1 Supplies required to build a cardboard boat. (SAMPLE BOAT) 1. A sharp cutting tool 2. 1 quart (or more) of contact cement - (Gallon size shown) 3. 2 tubes (or more) of construction adhesive (like Liquid
More informationINSTALLATION INSTRUCTIONS FOR #101NS & #101QR FIXED BASE
INSTALLATION INSTRUCTIONS FOR #101NS & #101QR FIXED BASE #165 Anchor Kit #160/161 Epoxy Kit #163 Super Bundy Plus NOTE: BITUMINOUS PRODUCTS CANNOT BE USED TO INSTALL #101 FIXED BASE Revised MAY 2010 IMPACT
More informationMax Launch Abort System Prod. No *Kevlar is a registered trademark of Dupont
Flying Model Parts List Max Launch Abort System Prod. No. 3014 A 11820 - Body Tube 3.5 Diam x 5.5" Long B 11824 - Orange Capsule Base Shoulder Ring C 16032 - Laser-cut Ring motor mount rear D 16033 - Laser-cut
More informationSalter Industries Spiral Stair
Salter Industries Spiral Stair The Leader in Spiral Staircases Continuous Sleeve Stair Installation Instructions TOOLS NEEDED: 1. Electric drill with hex chuck and Phillips bit 2. Drill bits 1/8", 1/4",
More informationFMR-010 1/32 Scale Vietnam-era AH-1G Rocket Pods (M-158, M-200)
P.O. Box 126 Tanner, AL 35671-0126 USA www.fireballmodels.info FMR-010 1/32 Scale Vietnam-era AH-1G Rocket Pods (M-158, M-200) Contents: A) 2x M-200 Rocket Pod B) 1x M-200 Decal C) 14x Brass Tube D) 4x
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationPlans & Materials List for Handwashing Station
Plans & Materials List for Handwashing Station Required Tools Arc Welder (mig or stick) Chop or metal band saw Grinder (bench and/or handheld) 3/8" Drill 1/8", 1/4", 5/16" Drill Bits Copper Pipe Cutter
More informationA simple demand feeder can be made with a 5 gallon bucket, a funnel, brass rods and PVC pipe. It can hold 12 pounds of extruded (floating) fish feed.
How to build a demand feeder. A simple demand feeder can be made with a 5 gallon bucket, a funnel, brass rods and PVC pipe. It can hold 12 pounds of extruded (floating) fish feed. Use a typical 5 gallon
More informationINSTALLATION INSTRUCTIONS
Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.
More information