DESIGN GUIDE FOR INFINITY SYSTEMS

Size: px

Start display at page:

Download "DESIGN GUIDE FOR INFINITY SYSTEMS"

Britton Benjamin Griffin
5 years ago
Views:

1 Doc Rev B DESIGN GUIDE FOR INFINITY SYSTEMS WITH STAND ALONE OR MULTI-LINK FIRMWARE

3 TABLE OF CONTENTS 1. CABINET DIMENSIONS WIRE CHART...1 A. CABLING TO THE MAIN PROCESSOR BOARD... 1 B. CABLING TO THE TELEPHONE INTER FACE BOARD... 2 C. CABLING BETWEEN UNITS WITH DUAL SHORT HAUL MODEMS... 2 D. CABLING BETWEEN UNITS WITHOUT DUAL SHORT-HAUL MODEMS... 2 E. CABLING FOR ADDITIONAL FEATURES... 2 F. CABLING FOR FACTORY-SUPPLIED VIDEO CAMERA OPTION DIMENSIONAL DRAWINGS OF INFINITY...4 A. INFINITY L SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV)... 4 B. INFINITY L FLUSH MOUNT SYSTEM... 5 C. INFINITY M SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV)... 6 D. INFINITY M WITH CAMERA FLUSH MOUNT SYSTEM... 7 E. INFINITY S SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV)... 8 F. INFINITY S FLUSH MOUNT SYSTEM... 9 G. INFINITY DI SURFACE MOUNT SYSTEM...10 H. INFINITY DI FLUSH MOUNT SYSTEM I. INFINITY B SYSTEM J. CAMERA MOUNTING ILLUSTRATION OF PROCESSOR BOARDS...14 A. MAIN PROCESSOR BOARD (REVISIONS E THROUGH F ) B MODEL TELEPHONE INTERFACE BOARD C. AUXILIARY RELAY MODULE BOARD D POWER SUPPLY BOARD IMPORTANT: The Sentex Systems, Inc. warranty on this system is conditioned upon Sentex Systems, Inc. being paid in full for this equipment. The warranty will not be honored until such payment is received by Sentex Systems, Inc. Copyright 2000 All Rights Reserved This document is protected by copyright and may not be copied or adapted without prior written consent of Sentex Systems, Inc. This document contains the information proprietary to Sentex and such information may not be distributed without the prior written consent of Sentex. The software and firmware included in the Sentex Infinity system as they relate to this documentation are also protected by copyright and contain information proprietary to Sentex. Sentex Systems Chatsworth, CA Visit us at Rev B Doc

5 The purpose of this guide is to assist you in meeting any specification requirements you may encounter in installing an Infinity system. The information enclosed in this manual is to be used for reference purposes only and is not intended to be an installation or programming manual. 1. CABINET DIMENSIONS TYPE OF SYSTEM HEIGHT WIDTH DEPTH Infinity L or DI Surface Mount /16 4 1/4 Flush Mount Back Box 21 1/4 16 3/4 3 3/16 Flush Mount Bezel 23 11/ /16 Infinity M or S Surface Mount /4 3 1/4 Flush Mount Back Box 16 7/ /4 2 1/4 Flush Mount Bezel 18 3/4 14 1/2 Infinity B: /4 2. WIRE CHART PLEASE NOTE: If the wires you are pulling for this installation are going to be run through an indoor, weather-proof location, it is acceptable to use unshielded cable. If the wires are going to be run through an outdoor location, we recommend that you use shielded cable. Recommendations for both types of cable are provided where needed. A. CABLING TO THE MAIN PROCESSOR BOARD Cabling to the Main Processor Board Type of Wire Recommendations From the power transformer or power supply 2 conductor cable See chart below: 120 VAC outlet From the door strike or the door strike 2 conductor cable See specifications for power supply the device you are installing. DC POWER WIRE SIZE DISTANCE AC POWER WIRE SIZE 18 AWG 30' and under 14 AWG 16 AWG 30'-75' 12 AWG 12 AWG 75'-150' AWG 150'-250' PLEASE NOTE: If you are using the larger sizes of cable (i.e., 12 awg or 10 awg), you may experience problems inserting the wires into the terminal block. If you encounter this problem, you can connect a awg wire (with the use of a wire nut) to each end of the power cable, as long as the smaller gage wire is under 12 inches in length. Rev B Doc Page 1 of 17

6 B. CABLING TO THE TELEPHONE INTER FACE BOARD Cabling to the Telephone Interface Board Type of Wire Recommendations From the telephone company jack 2 conductor, Shielded-Belden # to 22 awg cable Unshielded-Belden #8740 C. CABLING BETWEEN UNITS WITH DUAL SHORT HAUL MODEMS (Multi-Link Systems only) Type of Wire Recommendations From LINE 2 on the first unit and 2 conductor, 16 to 24 awg Shielded-Belden #9501 LINE 1 on the second unit (5000 ft. max.) twisted pair cable Unshielded-Belden #8740 D. CABLING BETWEEN UNITS WITHOUT DUAL SHORT-HAUL MODEMS (Multi-Link Systems only) Type of Wire Recommendations From TB3 on the first unit and 5 conductor, Shielded-Belden #9929 TB2 on the second unit (50 ft. max.) 18 to 24 awg cable Unshielded-Belden #8445 E. CABLING FOR ADDITIONAL FEATURES On an Infinity System Type of Wire Recommendations From a computer terminal 3 conductor Use shielded cable only to the Main Processor Board (50 ft. max.) 16 to 24 awg cable Shielded-Belden #9925 From a printer 3 conductor Use shielded cable only to the Main Processor Board (50 ft. max.) 16 to 24 awg cable Shielded-Belden #9925 From a Stand-Alone Modem 3 conductor Use shielded cable only to the Main Processor Board (50 ft. max.) 18 to 24 awg cable Shielded-Belden #9925 From a Remote Keypad 7 conductor Use shielded cable only to the Main Processor Board (500 ft. max.) 20 to 24 awg cable Shielded-Belden #9932 From a Weigand, Barium Ferrite, Proximity, or Clikcard card reader to the 5 conductor Use shielded cable only Main Processor Board (500 ft. max.) 24 awg cable Shielded-Belden #9929 On a Multi-Link System Type of Wire Recommendations Between a Computer Terminal 3 conductor Use shielded cable only and the first unit of the system (50 ft. max.) 18 to 24 awg cable Shielded-Belden #9925 Between A Computer Terminal 2 conductor, Use unshielded cable only and a Stand-Alone Short Haul Modem (50 ft. max.) 16 to 24 awg, Unshielded-Belden #8740 twisted pair cable Between a Printer and the 3 conductor Use shielded cable only first (or last) unit of the system (50 ft. max.) 18 to 24 awg cable Shielded-Belden #9925 Between a Printer and a 2 conductor, Use unshielded cable only Stand-Alone Short-Haul Modem (50 ft. max.) 16 to 24 awg, Unshielded-Belden #8740 twisted pair cable Between a Printer and 2 conductor Use shielded cable only the AUX port of a terminal (50 ft. max.) 18 to 24 awg cable Shielded-Belden #9501 Page 2 of 17 Doc Rev B

7 On a Multi-Link System (Continued) Type of Wire Recommendations Between an External Telephone Modem 3 conductor Use shielded cable only and the first unit of the system (50 ft. max.) 18 to 24 awg cable Shielded-Belden #9925 Between an External Telephone Modem 2 conductor, Use unshielded cable only and a Stand-Alone Short-Haul Modem (50 ft. max.) 16 to 24 awg, Unshielded-Belden #8740 twisted pair cable Between a Remote Keypad 7 conductor Use shielded cable only and a unit within the system (500 ft. max.) 20 to 24 awg cable Shielded-Belden #9932 Between a Weigand, Barium Ferrite, Proximity, or Clikcard card reader 5 conductor Use shielded cable only and a unit within the system (500 ft. max.) 24 awg cable Shielded-Belden #9929 F. CABLING FOR FACTORY-SUPPLIED VIDEO CAMERA OPTION Cabling for Factory-Supplied Video Camera Option Type of Wire Recommendations From the separate power transformer 2 conductor cable See chart below: At the 120 VAC outlet Between the video output and a Single Conductor Belden #9240 Video Monitor (100 ft. max) 75 Ohm RG-59/u coaxial cable DC POWER WIRE SIZE DISTANCE AC POWER WIRE SIZE 18 AWG 30' and under 18 AWG 18 AWG AWG 18 AWG AWG 16 AWG AWG 12 AWG AWG Rev B Doc Page 3 of 17

8 3. DIMENSIONAL DRAWINGS OF INFINITY A. INFINITY L SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV) This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity L system itself. NOTE: Camera is optional. Page 4 of 17 Doc Rev B

9 B. INFINITY L FLUSH MOUNT SYSTEM FLUSH MOUNT BOX This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity L Flush Mount system itself. Rev B Doc Page 5 of 17

10 C. INFINITY M SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV) This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity M system itself. NOTE: Camera is optional. Page 6 of 17 Doc Rev B

11 D. INFINITY M FLUSH MOUNT SYSTEM FLUSH MOUNT BOX This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity M Flush Mount system itself. Rev B Doc Page 7 of 17

12 E. INFINITY S SURFACE MOUNT SYSTEM (SHOWN WITH OPTIONAL CCTV) This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity S system itself. NOTE: Camera is optional. Page 8 of 17 Doc Rev B

13 F. INFINITY S FLUSH MOUNT SYSTEM FLUSH MOUNT BOX This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity S Flush Mount system itself. Rev B Doc Page 9 of 17

14 G. INFINITY DI SURFACE MOUNT SYSTEM This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity DI system itself. Page 10 of 17 Doc Rev B

15 H. INFINITY DI FLUSH MOUNT SYSTEM FLUSH MOUNT BOX This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity DI Flush Mount system itself. Rev B Doc Page 11 of 17

16 I. INFINITY B SYSTEM This line drawing is intended for dimensional reference purposes only and is not intended to be an actual drawing of the Infinity B system itself. Page 12 of 17 Doc Rev B

17 J. CAMERA MOUNTING This drawing is provided for your information only. Side View Rev B Doc Page 13 of 17

18 4. ILLUSTRATION OF PROCESSOR BOARDS A MAIN PROCESSOR BOARD (REVISIONS E THROUGH F ) Page 14 of 17 Doc Rev B

19 B MODEL TELEPHONE INTERFACE BOARD Rev B Doc Page 15 of 17

20 C. AUXILIARY RELAY MODULE BOARD Page 16 of 17 Doc Rev B

21 D POWER SUPPLY BOARD WITH BOARD MOUNT CAMERA IMPORTANT NOTE: Do not use the same power supply for this board as for the telephone entry system. The power inputs must be isolated. Rev B Doc Page 17 of 17

Doc Rev. B DESIGN GUIDE SPECTRUM TELEPHONE ENTRY SYSTEM WITH THE -101 BOARD

Doc Rev. B DESIGN GUIDE SPECTRUM TELEPHONE ENTRY SYSTEM WITH THE -101 BOARD Doc. 6001214 Rev. B DESIGN GUIDE SPECTRUM TELEPHONE ENTRY SYSTEM WITH THE -101 BOARD INTRODUCTION The purpose of this guide is to assist you in meeting any specification requirements you may encounter